The sun provides us daily with large quantities of energy in the form of light. With the world’s increasing demand of electrical energy the prospect of converting this solar light into electricity is highly tempting. In the strive towards mass-production and low cost solar cells, new types of solar cells are being developed, e.g. solar cells completely based on organic molecules and polymers. These materials offer a promising potential of low cost and large scale manufacturing and have the additional advantage that they can be produced on flexible and light weight substrate which opens for new and innovating application areas, e.g. integration with paper or textiles, or as building materials. In polymer solar cells a combination of two materials are used, an electron donor and an electron acceptor. The three dimensional distribution of the donor and acceptor in the active layer of the device, i.e. the morphology, is known to have larger influence of the solar cell performance. For the optimal morphology there is a trade-off between sometimes conflicting criteria for the various steps of the energy conversion process. The dissociation of photogenerated excitons takes place at an interface between the donor and acceptor materials. Therefore an efficient generation of charges requires a large interface between the two components. However, for charge transport and collection at the electrodes, continuous pathways for the charges to the electrodes are required. In this thesis, results from morphology studies by atomic force microscopy (AFM) and dynamic secondary ion mass spectrometry (SIMS) of spin-coated blend and bilayer thin films of polyfluorene co-polymers, especially poly[(9,9-dioctylfluorenyl-2,7-diyl)-co-5,5-(4´,7´-di-2-thienyl-2´,1´,3´-benzothiadiazole)] APFO-3, and the fullerene derivative [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) are presented. It is shown that by varying the blend ratio, the spin.-coating solvent, and/or the substrate, different morphologies can be obtained, e.g. diffuse bilayer structures, spontaneously formed multilayer structures and homogeneous blends. The connection between these different morphologies and the performance of solar cells is also analysed. The results indicate that nano-scale engineering of the morphology in the active layer may be an important factor in the optimization of the performance of polymer solar cells.

Based on the solar cell¡¦s four characteristic parameter open-circuit voltage (Voc) makes the discussion.The study of the relation VOC¡¦s paper uses empirical formula. VOC¡¦s formula is ¡§VOC=(1/e)(¡UEDonorHOMO¡W-¡UEAcceptorLUMO¡W)-0.3V¡¨. We can know that VOC related to donor material¡¦s HOMO and acceptor material¡¦s LUMO, if we need a high VOC, it can change the structure of donor material to have higher HOMO value, as well as the acceptor material have lower LUMO value. Our active layer except poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-Butyric acid methyl ester (PCBM), the third material was blended to discuss their effect on the VOC. Two kind of different bromined-P3HT (Br-P3HT) were used 40% and 100% bromined-P3HT to blend in active layer. Their Three materials blended under the different weight percent and the basic device configurations in this study was ITO / PEDOT : PSS / P3HT : Br-P3HT : PCBM / Al , efficiency was measured under AM 1.5G 100mW/cm2 illumination. When blended Br-P3HT(100%) in the active layer, VOC increased from 0.6V to 0.68V and the surface roughness makes short-circuit current and fill factor, increased make lower power conversion efficiency. When blended Br-P3HT(40%) into the active layer, not only can increase VOC to 0.66V, but influence the short-circuit current and the fill factor. The power conversion efficiency changed from 2.20% to 2.46%.

Ce travail a été consacré à la caractérisation, l'optimisation et l'étude du comportement photochimique de couches actives de cellules photovoltaïques organiques. L'objectif était d'identifier les mécanismes de photovieillissement dans le but de proposer des stratégies pour améliorer la stabilité de cellules solaires organiques à base de Poly(3-hexylthiophène) (P3HT) et de [6,6]-phényl-C61-butanoate de méthyl (PCBM). Le premier axe de travail a été consacré à l'étude de l'influence des paramètres structuraux du P3HT (masse molaire, régiorégularité, pureté ...) sur sa stabilité photochimique dans un premier temps, puis sur l'optimisation des performances des cellules dans un second temps. Pour ce faire, quatre P3HT commerciaux différents ont été étudiés. Ils ont tout d'abord été caractérisés avec précision grâce à différentes techniques analytiques. La relation entre microstructure du P3HT et sa photostabilité a ensuite été étudiée, et les paramètres pertinents influençant la photodégradation identifiés. Le deuxième axe de travail a été consacré à la stabilité photochimique de mélanges P3HT:PCBM sur substrat inerte, puis sur des couches tampons. Dans une dernière partie, la dégradation de couches actives au sein de dispositifs complets a été effectuée en faisant " l'autopsie " de cellules vieillies.

A long-term goal within the field of organic electronics has been to developflexible and functional devices, which can be processed and patterned withlow-cost and energy-efficient solution-based methods. This thesis presents anumber of functional paths towards the attainment of this goal via thedevelopment and demonstration of novel fabrication and patterningmethods involving the important organic-semiconductor family termedfullerenes.Fullerenes are soccer-shaped small molecules, with two often-employedexamples being the symmetric C60 molecule and its more soluble derivative[6,6]-phenyl-C61-butyric acid methyl ester (PCBM). We show that PCBM canbe photochemically transformed into a dimeric state in a bi-excited reactionprocess, and that the exposed material features a significantly reducedsolubility in common solvents as well as an effectively retained electronmobility. This attractive combination of material properties allows for adirect and resist-free lithographic patterning of electronic PCBM films downto a smallest feature size of 1 µm, using a simple and scalable two-stepprocess constituting light exposure and solution development. In a furtherdevelopment, it was shown that the two-step method was useful also in thearea-selective transformation of fullerene/conjugated-polymer blend films,as demonstrated through the realization of a functional complementary logiccircuit comprising a 5-stage ring oscillator.In another project, we have synthesized highly flexible, single-crystal C60nanorods with a solution-based self-assembly process termed liquid-liquidinterfacial precipitation. The 1-dimensional nanorods can be deposited fromtheir synthesis solution and employed as the active material in field-effecttransistor devices. Here, it was revealed that the as-fabricated nanorods canfeature an impressive electron mobility of 1.0 cm2 V-1 s-1, which is on par withthe performance of a work horse in the transistor field, viz. vacuumdeposited amorphous Si. We further demonstrated that the processability ofthe nanorods can be improved by a tuned light-exposure treatment, duringwhich the nanorod shell is polymerized while the high-mobility interior bulkis left intact. This has the desired consequence that stabile nanoroddispersions can be prepared in a wide range of solvents, and we anticipatethat functional electronic devices based on solution-processable nanorodscan be realized in a near future.

P3HT single layer, P3HT/PCBM bilayer and P3HT/PCBM inverted bilayer devices were produced by spin coating organic layers onto ITO patterned glass in air, and clamping it with an Au coated silicon wafer, as top electrode, at the end (Figure13). Normal and inverted bilayer devices were also fabricated with and without PEDOT:PSS. All devices were divided into two groups by changing concentration of P3HT solution. The first group of devices contained 1.0 wt. % P3HT solution (P3HT in dichlorobenzene); the second group 0.56wt %. Power conversion efficiency, short circuit current, open circuit voltage, fill factor and maximum extracted power were measured on all produced devices. In contrast, all devices with 1.0wt % P3HT concentration showed better result than the devices with 0.56wt %. The highest result was obtained for P3HT single layer devices in both cases with short circuit current 56uA/cm2, open circuit voltage 0.94mV, maximum power 11.4uW/cm2 and power conversion efficiency of 0.11%. Inverted bilayer devices performed better than the non-inverted one. The devices with PEDOT:PSS got slightly better performance than the non-PEDOT:PSS used one. Charge carrier mobility measurement was done for all fabricated devices with charge extraction by linearly increasing voltage (CELIV) and dark injected space charge limited current (DI-SCLC) methods. All devices showed same magnitude of charge carrier mobility 10-5 cm2/V.s, the highest value still belongs to P3HT single layer device. The charge carrier mobility in all devices observed by DI-SCLC technique is one order of magnitude higher than by CELIV technique. This may be due to DI-SCLC method`s restriction on ohmic contacts between material and electrode. / بۇ تەتقىقاتتا ئورگانىك ماتېرىيالدىن پايدىلنىپ ئۈچ خىل قۇياش ئىنىرگىيەلىك باتارىيە ئادەتتىكى ئۆي مۇھىتىدا ياساپ چىقىلدى. ئەڭ چوڭ توك كۈچى، ئەڭ                                                    يۇقىرى بېسىم، ئەڭ يۇقىرى قۇۋەت ۋە زەرەت يۆتكۈلۈش تېزلىكى ئۆلچەپ چىقىلدى ئۇيغۇر

In recent years, organic photovoltaics (OPVs) have attracted considerable attention as a potential source of renewable energy over traditional materials due to their light weight, low production cost, mechanically stability and compatibility with flexible substrates in roll to roll processing for high volume production. In the OPVs interface plays an important role in determining the performance of the device. Interface signifies formation of efficient contact with electrode, film, and transport of free charge carrier, which results in better performance in the device. Interface engineering also helps in improving mechanical robustness of the device. Hence, understanding of interface, modification and its evaluation is important in fabrication of efficient device. In this thesis interface is modified such that the performance of the device can be improved (chapter 3 and chapter 4). In Chapter 5 and chapter 6 interface is modified such that device can be fabricated on uncommon substrate. Fabrication of device on uncommon substrates (fiber reinforced plastic and flexible glass substrate), has unique challenges. In chapter 5 and chapter 6, we look at how interface is modified to overcome the challenges associated and also understand the role of interface in improving the performance of device on such substrates is discussed. In Chapter 1 we discuss about working of organic solar cells and the challenges associated in device fabrication. Understanding of interface to overcome challenges associated is explained. It also covers brief introduction to the succeeding chapters discussed in the thesis and its recent developments. To understand the properties of interface and to analyze device performance various characterization techniques have been used are discussed in chapter 2. This chapter also covers the materials and general device fabrication techniques used in this thesis. In chapter 3, a narrow bandgap (NBG) polymer used as a near IR sensitizer in P3HT: PCBM blend. Since, P3HT with a band gap of ~1.9 eV, the commonly used p-type material absorbs approximately ~25 % of incident light. Hence, MP2 (NBG polymer) is used along with P3HT: PCBM in active layer to form a ternary blend, which helps in increased absorption. Basic properties of MP2 are evaluated using UV-visible spectroscopy, differential scanning calaorimetry(DSC), thermogravimetric analyser (TGA), gel permeation chromatography (GPC) and photoluminescence (PL) techniques. To evaluate enhanced absorption of ternary UV-visible spectroscopy is carried out. Charge transfer from one moiety to other in ternary blend is evaluated using PL and Ttime resolved microwave conductivity (TRMC). Morphology of the ternary is assessed using atomic force microscope (AFM) and structural characterization is carried out by X-ray diffraction (XRD). Performance of the device is evaluated by current-voltage (J-V) characterizations. Further improved performance is supported by external quantum efficiency (EQE). Charge extraction with linear increasing voltage (CELIV) of the device is done to evaluate the recombination mechanism in the device and to assess the performance of the device. One-dimensional (1D) ZnO nanostructures provide direct paths for charge transport, and also offer large interfacial area to make them an ideal electron transport layer. In chapter 4 highly aligned ZnO nanorods is used as electron transport layer in OPV. Growth of ZnO nanorods is two-step processes, growing seed layer and growing ZnO nanorods from hydrothermal process using an appropriate seed layer. Two different soft-chemical solution- growth methods (upward and downward) are developed to fabricate self-assembled, oriented ZnO nanorods. Substrate mounting, surface properties and optical transmittance are optimized by varying the nanorods growth conditions. Further the ZnO nanorods are UV ozone treated and its effect on performance of nanostructured buffer layer based device is evaluated. In Chapter 5 OPV is fabricated on an opaque FRP substrate. Fabrication of OPV device on opaque substrate plastic is unique and hence understanding various properties is vital. Such devices fabrication require bottom up approach, with transparent electrode as the top electrode and metal electrode on the surface of FRP. FRP has inherent rough surface of about few microns RMS roughness. In order to reduce the roughness of the substrate FRP was planarized. The planarized layer is chosen, such that it chemically binds with the substrate. The chemical interaction between substrate and planarizing coating is evaluated by FTIR and Raman spectroscopy. The binding of planarized layer and FRP is evaluated using nanoscratch technique and surface energies are studied using contact angle measurements. In addition, adhesion properties of the metal electrodes, which are deposited on planarized FRP are evaluated using nanoscratch technique. Fabrication of OPV requires a top transparent electrode. Simple spin coating technique is used to optimize the top electrode. The property of top electrode is evaluated using UV-visible spectroscopy for transmittance, and sheet resistance of the electrode is characterized. OPV device is fabricated on planarized FRP substrate using optimized top transparent electrode and its PV properties is evaluated. Performance of the device is evaluated for two different bottom electrodes and further performance of device is enhanced using buffer layers. Usually flexible OPVs are fabricated on plastic substrate such as PET, PEN. However they are not structurally stable at high temperatures and have high oxygen and moisture Permeability. In Chapter 6 Organic based photovoltaic devices were fabricated on flexible glass. Flexible glass has high strength and it is also known for low oxygen and moisture permeability. Fabrication of device on flexible glass has never been done before and hence, generation of data is necessary for commercialization of the technology. Device fabrication is optimized by using two different transparent conducting layers (ITO- sputter deposited, PEDOT: PSS-solution processed) and device performance was evaluated for both. Since the substrate is flexible in nature understanding the performance of the device during flexing is important. For this 2-parallel plate flexural apparatus is fabricated for in-situ measurements along with current voltage measurements. These devices are flexed cyclically and performance of device is evaluated. Therefore, work discussed in the thesis show by modifying the interface of the device, and understanding various interfaces of the device is crucial for improving the performance of the device. Also by engineering the interface, devices can be fabricated on various types of substrate.

Durable, cheap, and lightweight polymer based solar cells are needed, if simply to meet the demand for decentralized electrical power production in traditionally “off-grid” areas. Using a blend of Poly(3-hexylthiophene-2,5-diyl) (P3HT), Phenyl-C61-butyric acid methyl ester (PCBM), and the low band-gap polymer Poly[2,6-(4,4-bis-(2- ethylhexyl)-4H-cyclopenta [2,1-b;3,4-b′]dithiophene)-alt-4,7(2,1,3-benzothiadiazole)] (PCPDTBT), we have fabricated devices with a wide spectral response and 3% power conversion efficiency in AM 1.5 conditions; however, this thin film system exhibits only 0.43 optical density at 500 nm. To improve the performance of this polymer blend photovoltaic, we aim to increase absorption by adding CdSe(ZnS) core (shell) quantum dots. Four groups of devices are fabricated: a control group with an active polymer layer of 16 mg/mL P3HT, 16 mg/mL PCBM, and 4 mg/mL PCPDTBT; and three groups with dispersed quantum dots at 4 mg/ml, 1 mg/mL, and 0.25 mg/mL. The (CdSe)ZnS quantum dots are coated with octadecylamine ligands and have a peak absorbance at 560 nm and peak emission at 577 nm. The active layer was dissolved in chlorobenzene solvent and spun on glass substrates, patterned with indium tin oxide. The devices were then annealed for fifteen minutes at 110° C, 140° C, and 170° C. Current-voltage characteristic curves v and optical density data were taken before and after the anneal step. Finally, surface characterization was conducted with atomic force microscopy and electrostatic force microscopy. When compared to the control, the sensitized devices exhibited increased absorption and depressed electrical performance with increasing quantum dot loading. The surface morphology, both electrical and physical, showed deviation from the typical values and patterns shown by the control that increased with quantum dot loading. When the degrading electrical characteristics, increasing optical absorbance, and surface changes, are considered together, it becomes likely that the quantum dots interact in a significant manner with the morphology of the P3HT phase, which leads to an overall decrease in performance.

This thesis studies the degradation of perovskite photovoltaic cells placed in atmospheres of different moisture. Samples with inverse structure: ITO/ PEDOT:PSS/ CH3NH3PbI3–XClX / PC70BM/ Ca/ Al were prepared. Electrical characteristics were measured for 2 months and similar degradation trend was observed for all the samples. Perovskite cell efficiency PCE decreased to 20 % of the initial value in t80= 46±3 days in laboratory, t80=23±1$ days in nitrogen atmosphere and t80=25,7±0,6 dní days in dry atmosphere. For the initial 27 days of the experiment, a faster degradation linked with the decrease of ISC, FF and VOC was observed. After this period, the value of FF has stabilised at 0,777±0,009 % and the value of VOC at 0,70±0,02 % of their original value (in the laboratory atmosphere). Additional fall of PCE resulted only from the decrease of ISC and was slower than in the initial period. From the results acquired, it has emerged that during the experiment, the cell encapsulation provided a sufficient barrier against outer moisture. Residual moisture present in the sctructure, was labeled as the source of the degradation. The moisture is believed to enter with the hygroscopic material PEDOT:PSS during the samples preparation procedure. During the degradation, absorption measurements of photovoltaic cells were executed. The absorption spectra didn't change. That indicates, that the decrease of ISC is not caused by the reduction of light absorption. The thesis also studied the degradation of perovskite solar cells under illumination. The samples were exposed to UV radiation for 55,5 hours. The PCE time of decrease to 20 % of the initial value was t80 = 6±2 days. It was revealed, that UV radiation significantly accelerates the decrease of ISC.

This diploma thesis concentrates on the properties characterization of new organic materials for solar cells. In the theoretical part, there is a solar cells themed literature search, there is described a mechanism of conversion of solar energy, factors influencing photovoltaic conversion efficiency and materials using for preparation of organic solar cells. The practical part includes the preparation of solar cells and characterization of optical and electrical properties of the studied materials in thin layers and solutions. Used materials were conjugated polymers and derivatives of fullerenes.

No description available.