Certains procédés de production d’énergie nécessitent l’utilisation de poudres de biomasse, par exemple la gazéification en réacteur à flux entraîné (RFE). Cependant, les poudres de biomasse ont une mauvaise coulabilité. L’objectif de cette thèse est d’étudier leurs propriétés d’écoulement dans le contexte de la gazéification en RFE, à l’échelle du laboratoire et à l’échelle pilote. A l’échelle du laboratoire, des mesures en tambour rotatif, des tests de cisaillement et des mesures de densité ont été effectués. D’une part, une corrélation est mise en évidence entre la cohésion (issue des tests de cisaillement), la densité et l’angle d’avalanche (tiré des mesures en tambour). Ainsi, un paramètre difficile à obtenir comme la cohésion peut l’être à partir de mesures simples. D’autre part, l’influence de l’humidité sur la coulabilité des poudres de biomasse a été évaluée. L’humidité n’a pas d’effet significatif sous 15 % (en masse, base humide), car l’eau est adsorbée dans la structure de la biomasse ; les particules gonflent et ne sont pas liées par des ponts liquides. Un procédé de granulation humide est proposé. Un liant issu de déchets de biomasse est ajouté à la poudre pour former des granulés d’environ 1 mm. Leur forme sphérique diminue l’entrelacement des particules et leur faible polydispersité diminue le nombre de points de contact. Une amélioration de l’écoulement est observée à l’échelle labo. Une étude énergétique montre que la consommation énergétique du procédé peut descendre jusqu’à 12% du pouvoir calorifique inférieur, ce qui suggère une potentielle rentabilité économique du procédé. Enfin, la caractérisation à l’échelle supérieure est effectuée dans un pilote reproduisant l’injection en RFE. Les résultats montrent le rôle essentiel de la sphéricité et d’une faible polydispersité des particules. L’effet positif de la torréfaction et de la granulation sur la coulabilité est mis en évidence. / Some power generation processes require the biomass to be finely ground, such as biomass gasification in entrained flow reactors. However, fine biomass powders are cohesive and present flow issues. This thesis aims to study the biomass powder flowability in the context of the entrained flow gasification process. Biomass powders are characterized both at laboratory scale and pilot scale. Characterization at lab scale consisted of rotating drum measurements, shear tests and density measurements. First, a correlation is found between the cohesion (derived from shear tests), the powder density and the avalanche angle (derived from the rotating drum measurements). Thus, parameters difficult to get such as the cohesion can be obtained with easy to perform measurements. Then, the influence of moisture content on wood powder flowability has been assessed. No significant effect of the water content is found below 15 wt% (wet basis). Below 15%, as water is adsorbed in the biomass structure, the particles swell without being linked by liquid bridges. A wet granulation method is proposed. Biomass waste binders are added to the powder to form granules around 1 mm. The spherical shape lowers the interlocking phenomenon. The low size dispersity of the grains decreases the number of contact points between particles. An improvement of the flowability at lab scale is observed. An energetic study of the granulation process is proposed, showing the energy consumption can be as low as 12% of the biomass Lowest Heating Value. Thus, the process is potentially economically profitable. Finally, characterization at pilot scale is performed with a device mimicking the injection in an entrained flow reactor. The results show the essential roles in the injection step of both the spherical shape and the narrow size distribution of the particles. The positive effect of torrefaction and granulation on the flowability is highlighted.

The regulations of many food products in the United States have been made and followed very well but unfortunately some products are not put under such rigorous standards as others. This leads to products being sold, that are thought to be healthy, but in reality contain unknown ingredients that may be hazardous to the consumers. With the use of several instrumentations and techniques the detection, characterization and identification of these unknown contaminates can be determined. Both the AZ-100 and the TE2000 inverted microscope were used for visual characterizations, image collection and to help guide the extraction. Direct analyte-probed nanoextraction (DAPNe) technique and nanospray ionization mass spectrometry (NSI-MS) was the technique used for examination and identification of all adulterants. A Raman imaging technique was than introduced and has proven to be a rapid, non-destructive and distinctive way to localize a specific adulterant. By compiling these techniques then applying them to the FDA supplied test samples three major adulterants were detected and identified.

The production of metal powders by water atomisation is a well established process, which can be used to produce a wide range of particle sizes. A careful control of the particle size distribution is necessary, to atomise powders with a high quality and at a low production cost. Therefore, it is necessary to have a substantial knowledge of the relation between operational parameters and the particle size, to be able to produce water atomised metal powders with consistent and high yields. The main purpose with this thesis was to increase the knowledge about factors which affect the mass median particle size (d50) for water atomised metal powders. The specific objectives with the study were to develop a theoretical d50 model and to investigate the relation between the particle size and the physical properties of the liquid metal. Pilot scale experiments for liquid iron showed that alloy additions of carbon and sulphur decreased the d50 value, at a maintained liquid steel temperature before atomisation. Moreover, it was indicated that the reduced particle size at increased %C and %S contents may be related to a decreased viscosity and surface tension of the liquid metal, respectively. An alternative explanation could be that raised superheats at increased carbon contents increased the total available time for atomisation, which may have contributed to a reduction of the d50 value. The theoretical d50 model developed in this work showed a very good correlation to the current experimental data. The model considers the influence of surface tension, viscosity, melt stream diameter, water pressure, water jet angle and water to metal ratio. This model was further used to analyse how the d50 value was influenced by the viscosity and the surface tension. A reduced viscosity from 4∙9 to 2∙1 mPa s decreased the d50 value with 33%. In addition, the particle size was estimated to decrease with 21% by decreasing the surface tension from 1840 to 900 mN m-1. / Q 20120529

Due to the high efficiency and productivity of continuous casting process, this method has been the most employed process to produce steel in past decades. The need to improve and optimize the finished product made it essential to gain more knowledge about the process, types of defects that may occur and the reasons for them. Moreover, the solutions for reducing the shortcomings in continuous casting process have been an intriguing subject to study. Many attempts have been done in order to reach this goal. Understanding, determining and optimizing the mould flux slag properties is especially important, since it plays an important and significant role in this process. For this, it is of outmost importance to acquire more knowledge about different properties of mould flux powders. Hence, there has been a world wide effort to measure and model the properties of mould flux properties, such as liquidus and solidus temperatures, heat capacity, enthalpy, thermal expansion, density, viscosity, electrical conductivity, surface tension and thermal conductivity. This thesis presents a brief review on continuous casting process, mould flux powder and its properties and characteristics. Furthermore, it focuses on the thermo-physical properties of mould fluxes. In present work, different industrial mould flux powders have been analyzed to measure their viscosity, break temperature, physical properties such as density, flowablity of powder, slag structure and chemical composition. The experimental data have been compared to some of the most commonly used models such as Riboud model, Urbain model, Iida model and KTH model.

As many of the dairy powders manufactured have to travel long distances to reach their customers, both domestically and internationally, there is considerable interest among dairy powder manufacturers to maintain the quality of their products for relatively long storage periods. Dairy powders can have a long shelf life if packaged and stored properly. Vacuum packaging can be an attractive packaging strategy to maintain the quality of dairy powders and provide added value by improving the efficiency of using the storage space; because of the inherent compactness of these products. Vacuum packaged dry dairy ingredients may also have added ease of handling for end users. However, little is known about the impact of vacuum packaging on the physical properties of dry dairy ingredients. The main objective of this study was to determine the effect of vacuum packaging over 12 months storage on particle size, particle density, bulk density, tapped density, flowability, compressibility, color, moisture content, surface morphology, and solubility of six types of dairy powders. In addition, the effect of dairy ingredients type was also assessed. Commercial samples of nonfat dry milk powder, whole milk powder, buttermilk powder, milk protein Isolate, whey protein concentrate#80, and sweet whey powder were repackaged in duplicate using multi-wall foil side gusseted bags under varying degrees of vacuum (1, 0.7, 0.4 bar) and a control with no vacuum, then stored for 3, 6, and 12 months at 25°C and 60% relative humidity. Each powder was sampled and analyzed in duplicate for all the above listed quality attributes, upon receiving the powder and after 3, 6, and 12 months of storage. Moreover, the effect of vacuum packaging on storage space was evaluated comparing three different models; Model (1) represented a 25 kg bag of atmospheric packaged non fat dry milk with the actual dimensions of a commercial 25 kg bag of non fat dry milk. Model (2), a hypothetical model, represented a 25 kg bag of vacuum packaged non fat dry milk with a length and a width equal to those of model (1). Model (3), another hypothetical model, also represented a 25 kg bag of vacuum packaged non fat dry milk with a length equal to half of a pallet width and a width equal to one third of a pallet length, in order to achieve the highest pallet efficiency possible. The pallet used for all three models was considered to be a (48 × 40) pallet. The height of models 2 and 3 was allowed to reflect the bulk reduction effect of vacuum packaging and was determined based on the weight, density and the known dimensions of the bags. It is important to note that the density of models 2 and 3 was assumed to be equal to the density of a small bag of nonfat dry milk. The saved space per bag and pallet efficiency of vacuum packaging and atmospheric packaging were compared using the three models described above. Physical properties analyses of the dairy powders revealed statistically significant effect of vacuum pressure on only color values: L-, a-, and b but none of the other powder quality attributes examined. Powders packaged under vacuum showed a significantly higher mean of L- color value (p-value = 0.003 < 0.01), but significantly lower means of (a- and b-) color values (p-values = 0.005, and 0.001, respectively). This effect was more dramatic in high fat containing powder such as whole milk powder. In fact, vacuum packaged whole milk powders were significantly whiter, less red, and less yellow. It is likely that vacuum packaging has prevented color changes due to lipid oxidation in whole milk powder. Physical properties analyses of the dairy powders also revealed statistically significant increases in the particle density, particle size, bulk density, and tapped density due to the effect of storage time (all p-values = 0.000 < 0.01), statistically significant decreases in the angle of repose and compressibility due to the effect of storage time (p = 0.000 < 0.01) and (p = 0.004 < 0.01), respectively. The physical properties analyses also revealed a statistically significant effect of the powder type on particle density, particle size, bulk density, and tapped density, angle of repose, compressibility, and color values: L-, a-, and b- (all p-values = 0.000 < 0.01). In other words, particle density, particle size, bulk density, and tapped density of the powders increased over the storage time, while angle of repose (AOR) and compressibility decreased over the storage time. The powder type had a significant effect on particle density, particle size, bulk density, tapped density, AOR, compressibility, and color values: L-, a-, and b; however, it did not have any significant effect on solubility and moisture content. In addition, observations of the surface morphology of dairy powders were made using a scanning electron microscope. This evaluation demonstrated the differences in powder particle shape and surface morphology which are believed to be partially responsible for the significant differences observed in the physical properties, due to the effect of powder type. It was shown that vacuum packaging does increase the efficiency of using the storage space by removing the interstitial air and increasing the density of the powder. As described above, the height of model (2) and the length of model (3) both were expectedly shorter compared to those of model (1). Storage space calculations for non fat dry milk were performed based on comparing the volume of the 3 models and showed 15 % saving in storage space per bag and per pallet, due to vacuum packaging. The effect of space saving on the number of bags per pallet was evaluated using CAPE PACK v2.09 software and showed an increase from 45 bags/ pallet in model (1) to 50 bags/ pallet in model (2) and 54 bags/ pallet in model (3). Overall, this study demonstrates the impact of vacuum packaging on physical properties, solubility, and storage properties of dairy powders. The data suggest that the proposed vacuum packaging method may be beneficial to maintain the quality of the powders studied and it results in space savings per unit of dairy powder compared to conventional atmospheric packaging.

No / This paper presents the results of a recent comprehensive investigation of selective laser melting (slm) of prealloyed gas and water atomised M2 and H13 tool steel powders. The objective of the study was to establish the parameters that control the densification of single and multiple layers with the aim of producing high density parts without the need for infiltration. Powders were processed using continuous wave (CW) CO2 and Nd:YAG lasers. Relationships between alloy composition, powder particle size and shape, flowability, microstructure (phases present, their size, morphology and distribution), track morphology, post scanned density, surface finish and scan conditions (Laser power, spot size and scan speed) are discussed for single track, single layer and multi-layer (up to 25 layers) constructions. Processing with a Nd:YAG laser with powders placed on substrates rather than on a loose powder bed gave more stable builds than with the CO2 laser. Using the Nd:YAG laser densities up to ~90% relative were possible with H13 powder compared with a maximum of ~70% for M2 in multi-layer builds. Maximum density achieved with CW CO2 processing was only ~60%, irrespective of powder composition. The paper compares the processibility of these materials with stainless steel powders processed to higher densities (up to 99% relative) under similar conditions. The results of the work show that a crucial factor for high density processing is melt pool wettability and this is controlled largely by carbon content; low carbon contents producing better wettability, flatter tracks and higher densities. The significance of this observation for the processing high alloy steels by slm will be discussed.

No description available.

京都大学 / 新制・課程博士 / 博士(農学) / 甲第23249号 / 農博第2456号 / 新制||農||1084(附属図書館) / 学位論文||R3||N5339(農学部図書室) / 京都大学大学院農学研究科農学専攻 / (主査)教授 松村 康生, 教授 田尾 龍太郎, 教授 丸山 伸之 / 学位規則第4条第1項該当 / Doctor of Agricultural Science / Kyoto University / DGAM

Engineered components can gain desirable properties when coated with surface materials. Wear-resistant coatings can improve the performance of contacting surfaces and allow for an extended life of the parts. Hard chromium has been the plating material of choice for certain wear and corrosion- resistant coatings because of its desirable combination of chemical resistance, adhesion, and mechanical properties. However, hexavalent chromium, a component of the process for applying hard chromium coatings, has been recognized by the EPA as having hazardous health and environmental impacts. Existing and planned environmental regulations restricts the use of process chemicals containing hexavalent chromium ions. This substantiates a need to develop an environmental friendly process for alternative coatings. Praxair has reported that Cr-Ni-C particles have a better corrosion resistance than current chromium carbide and nickel chromium powders. Today, Cr-Ni-C provides great qualities for flame spray and does not contain the toxic compounds used to deposit hard chromium, but is not compatible with application by cold spray. The purpose of this thesis project is to compare two processes for plating metal powder, chromium nickel carbide (Cr-Ni-C, CRC-410-1 from Praxair), with nickel. The particles were encapsulated using three different methods: one electroplating method previously used on particles, and two electroless plating processes using different solutions. The Cr-Ni-C particles were successfully encapsulated with Ni by one of the electroless deposition methods. The electrolytic deposition experiments did not yield the uniformity of coating without agglomeration that is being attained in industrial practice today. Further research on this method is recommended, due to the material operational cost in an industrial setting that is projected to be over 200 times cheaper than electroless deposition method. In the meantime, it should be possible to produce enough coated powder by electroless deposition to validate the utility of this coated powder in depositing wear- and corrosion-resistant coatings of Cr-Ni-C by cold spray.

Esta tesis presenta un conjunto original de procedimientos para la síntesis de nanoestructuras de TiO2 y ZnO por biomimetización de membranas de cáscara de huevo obteniendo materiales valiosos para fotovoltaica como se muestra en su evaluación de rendimiento como ánodo en células solares sensibilizadas por colorante. "El manuscrito está dividido en 7 capítulos. En el primer capítulo, titulado Introducción, se presentan las bases teóricas para la comprensión de los procesos de biomimetización, membranas de cáscara de huevo, síntesis de ZnO y TiO2, y células solares sensibilizadas por colorantes (DSSC). Después del capítulo introductorio, el Capítulo 2 revela los objetivos generales y específicos de esta investigación. Posteriormente, el Capítulo 3 describe el procedimiento experimental utilizado para las síntesis y caracterizaciones de ZnO y TiO2, así como el procedimiento utilizado en el ensamblaje y la caracterización de las células fotovoltaicas. En el capítulo 4 se presentan y discuten los resultados obtenidos con las síntesis y la aplicación de los polvos como fotodoles en DSSC. En este capítulo, hemos decidido subdividirlo en secciones específicas para explicar cuestiones científicas específicas sobre el tema. En el capítulo 5 se presentan las conclusiones del estudio en vista de los diferentes aspectos: obtención de TiO2 biomimético y ZnO, diferencias entre los polvos sintetizados por biomimetización de las membranas de cáscara de huevo, y la caracterización de las células construidas con los polvos biomiméticos. / Esta tesi presenta un conjunt original de procediments per a la síntesi de nanoestructuras de TiO2 i ZnO per biomimetización de membranes de corfa d'ou obtenint materials valuosos per a fotovoltaica com es mostra en la seua avaluació de rendiment com a ànode en cèl·lules solars sensibilitzades per colorant. &#34;El manuscrit està dividit en 7 capítols. En el primer capítol, titulat Introducció, es presenten les bases teòriques per a la comprensió dels processos de biomimetización, membranes de corfa d'ou, síntesi de ZnO i TiO2, i cèl·lules solars sensibilitzades per colorants (DSSC) . Després del capítol introductori, el Capítol 2 revela els objectius generals i específics d'esta investigació. Posteriorment, el Capítol 3 descriu el procediment experimental utilitzat per a les síntesis i caracteritzacions de ZnO i TiO2, així com el procediment utilitzat en l'acoblament i la caracterització de les cèl·lules fotovoltaiques. En el capítol 4 es presenten i discutixen els resultats obtinguts amb les síntesis i l'aplicació de les pols com fotodoles en DSSC. En este capítol, hem decidit subdividir-ho en seccions específiques per a explicar qüestions científiques específiques sobre el tema. En el capítol 5 es presenten les conclusions de l'estudi en vista dels diferents aspectes: obtenció de TiO2 biomimético i ZnO, diferències entre les pols sintetitzats per biomimetización de les membranes de corfa d'ou, i la caracterització de les cèl·lules construïdes amb les pols biomiméticos. / This thesis introduces an original set of procedures for the Synthesis of ZnO and TiO2 nanostructures by biomimetization of eggshell membranes obtaining valuable materiales for photovoltaic as shown on their performance evaluation as anode in Dye-Sensitized Solar Cells". The manuscript is divided into 7 chapters. In the first chapter, entitled Introduction, it is presented the theoretical bases for the understanding of the biomimetization processes, eggshell membranes, ZnO and TiO2 syntheses, and dye-sensitized solar cells (DSSC). After the introductory chapter, Chapter 2 reveals the general and specific objectives of this research. Subsequently, Chapter 3 describes the experimental procedure used for the syntheses and characterizations of ZnO and TiO2 as well as the procedure used in the assembly and characterization of the photovoltaic cells. In chapter 4 are presented and discussed the results obtained with the syntheses and application of the powders as photoanodes in DSSC. In this chapter, we have chosen to subdivide it into specific sections to explain specific scientific issues on the subject. In chapter 5 the conclusions of the study are presented in view of the different aspects: obtaining ZnO and biomimetic TiO2, differences between the powders synthesized by biomimetization of eggshell membranes, and the characterization of the cells constructed with the biomimetic powders. / Camaratta, R. (2018). Synthesis Of ZnO and TiO2 By Biomimetization Of Eggshell Membranes And Its Evaluation As Anode In Dye-Sensitized Solar Cells [Tesis doctoral]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/113416