The Diploma thesis is adressing the issue of polymer-modified mortars (PMM) and theirs properties in dependence on curing conditions. The reasons of using polymer additives and some selected applications of PMM are described in theoretical part of this work. Cementitious composite (mortar) hardening is especially focused on mechanism of formation co-matrix system based on cement hydration products and polymer film in dependence on curing conditions. The knowledge of interaction of cement and ethylene-vinyl acetate (EVA) copolymer is presented in the latest paragraphs of theoretical work. Following practical part presents influence of EVA to physical and mechanic properties of PMM in dependence of dosage polymer additive and exogenous factors. The study of microstructure was investigated by scanning electron microscope and high-pressure mercury porosimetry. Tests and investigations are described and evaluated.

Denna rapport utreder möjligheten att implementera avfallsplast, specifikt polyeten, som polymertillsats i svenska asfaltvägar. Tekniken, med avseende på avfallsplast, används idag i begränsad utsträckning i andra länder samt utreds på flera håll som en möjlig metod att främja hållbar utveckling genom att öka materialåtervinningen av plast. I Sverige förbränns idag en stor mängd plast för energiåtervinning och införandet av metoden skulle, förutsatt att den ersätter en del av energiåtervinningen, bidra till att minska växthusgasutsläpp från fossila material. Det används idag jungfruliga polymerer som tillsatser i vägmaterial tillsammans med bitumen som utvinns ur råolja, införandet av metoden kan således även substituera uttag av fossila råvaror. För att inhämta resultatet har en litteraturstudie tillsammans med intervjuer med representativa experter inom området utförts. Resultatet redogör för plasters egenskaper och hur dessa fördelaktigt samverkar med, och kan integreras i, asfaltmaterial. Vidare hur dessa egenskaper bidrar till att klimatanpassa vägbyggnationer, leva upp till kravställningen på vägar samt hur egenskaperna utreds genom olika mätmetoder. Även negativa aspekter som kan uppstå kopplat till miljö- och hälsorisker redogörs för. Ett urval av aktuella aktörer som berörs av implementeringen presenteras ur konkurrens- och synergiperspektiv samt med en beskrivning av verksamhetens mål och drivkrafter kopplat till metoden. En stor del av aktörsperspektivet inhämtades från de genomförda intervjuerna med representanter inom asfaltindustrin, bitumentillverkning och innovations- och kemiindustrierna. Inställningen till implementeringen i syfte att arbeta med hållbar utveckling bedöms vara försiktigt positiv på grund av höga krav på sorteringsgrad, jämnhet hos materialströmmar samt eventuella följdproblem som kan följa av införandet. Däremot har tekniken visat sig vara positiv ur ett prestandahöjande perspektiv för vägen genom att vidga tillgängligt temperaturområde, öka åldrings-, deformations- och nötningsresistens samt vattenbeständigheten. För att göra en mer rättmätig bedömning, och ytterligare slutsatser, krävs vidare studier för att undersöka de långsiktiga effekterna av att tillämpa metoden i svenska vägar. / This report investigates the possibility to implement plastic waste, specifically polyethylene, as a polymer additive in Swedish asphalt roads. The technique, when applied with waste plastic, is used to a limited extent in other countries and is investigated as a method in order to forward sustainable development by increasing material recycling of plastics. A large quantity of plastics is incinerated for energy recovery in Sweden today and introducing the method would, given that it replaces parts of the energy recovery method, contribute to decrease greenhouse gas emissions derived from fossil materials. Today virgin polymers are used as additives in road materials as well as bitumen that is extracted from crude oil, introducing the method could therefore substitute the outtake of fossil raw materials. In order to obtain the result a literature review was carried out along with interviews with representative experts related to the area. The result presents properties of plastics and how these can beneficially cofunction and integrate with asphalt material. Furthermore, how these properties contribute to adapt the road to climatic changes, achieve overall related demands and how these properties are measured. Negative environmental and health aspects related to the method are also presented. A selection of would-be affected actors are portrayed with regards to competition and synergies as well as overall goals and driving factors related to the method. A large portion of the chapter portraying actors is based on the information collected during the interviews with representatives from the asphalt industry, bitumen manufacturers and the Chemical and innovation companies. The overall outlook on implementing the method in order to forward sustainable development is considered carefully optimistic, due to high requirements on consistent material streams and potential problems that can arise from the implementation. The technique has been proven to be beneficial regarding performance by broadening the available temperature range as well as increasing resistance towards aging, deformation, wear and water. In order to more precisely analyse and make conclusions regarding the method further studies regarding long-time effects in Swedish roads are needed.

Esta dissertação apresenta um estudo da deformação permanente de misturas asfálticas à luz dos resultados de ensaios de fluência por compressão uniaxial estática e dinâmica. Para isso, um programa experimental completo foi desenvolvido combinando fatores relacionados às misturas asfálticas e às condições de ensaio. Foram produzidos corpos de prova de misturas asfálticas densas tipo CAUQ com asfalto convencional (CAP 50/70) e com asfalto modificado com polímero SBS (CAP 50/70+SBS), variando o volume de vazios em dois níveis, 4 e 7%, e a presença de aditivo em dois níveis, sem e com cal hidratada. Os corpos de prova foram submetidos a ensaios de fluência com carregamentos estático e dinâmico em dois níveis de tensões, 0,1 MPa e 0,4 MPa, e em duas temperaturas diferentes, 40 e 50ºC. Essas condições do programa experimental permitiram observar o efeito do modificador SBS, da presença da cal e do volume de vazios nas misturas asfálticas, e entender o efeito da temperatura, do nível de tensão e do tipo de carregamento no comportamento de cada tipo de mistura asfáltica. Os resultados indicam que (i) a adição da cal promoveu redução de deformação acumulada somente nas misturas com ligante convencional (CAP 50/70); (ii) as misturas com volume de vazios de 7% apresentam maiores acúmulos de deformação permanente independente da presença de cal, do tipo de carregamento e da temperatura do ensaio, sendo maiores para a mistura asfáltica com CAP 50/70; (iii) as misturas com ligante modificado se mostraram menos sensíveis às variações da temperatura e do nível de tensão; (iv) e a melhora das características das misturas com asfalto modificado com polímero é detectada somente a partir de ensaios dinâmicos. / This paper presents a study of rutting on hot mixture asphalt (HMA) by means of static and dynamic creep tests. A full factorial experiment was developed considering factors related to HMA and to the test conditions. It was produced HMA (unmodified (CAP 50/70) and SBS modified binders) specimens at two different air voids (4 and 7%) and with or without hydrated lime. The specimens were submitted to static and dynamic creep tests at two stress levels, 0,1 MPa e 0,4 MPa, and two temperatures, 40 e 50ºC. These conditions of the experimental program allowed to observe the effects of the modifier SBS, the presence of the lime and the air voids in HMA, and to understand the effects of the temperature, stress and the type of loading on the behavior of each type of asphalt mix. The results indicate that (i) the addition of lime promoted reduction of accumulative deformation only in mixtures with conventional binder (CAP 50/70), (ii) mixtures with 7% air voids showed greater accumulation of permanent deformation regardless of presence of lime, the type of load and temperature of the test, mainly for the conventional HMA, (iii) the Polymer Modified Asphalt Hot Mix Asphalt (PMA-HMA) were less sensitive to temperature and the stress variation (iv) the improvement of the polymer modified asphalt mixture characteristics (PMA-HMA) were detected only on dynamic load conditions.

Untersuchungen zur Dauerhaftigkeit von ARGlasbewehrung im Textilbeton haben gezeigt, dass durch die Alkalität des Betons in Verbindung mit Feuchtigkeit eine Glaskorrosion hervorgerufen wird, die im Laufe der Zeit zu Festigkeitsverlusten des Glases führt. Eine Möglichkeit, die durch die Glaskorrosion verursachten Festigkeitsverluste zu reduzieren, stellt die Polymermodifikation des Betons dar. Durch die Polymerzugabe wird die Wasseraufnahme der Feinbetonmatrix reduziert, dadurch sinkt der Gehalt an gelösten Alkalien im Bereich der Bewehrung. Um den Einfluss verschiedener Feinbetonmatrices auf die Dauerhaftigkeit von Textilbeton beurteilen zu können, sind u. a. zeit- und tiefenabhängige Informationen zur Feuchteverteilung erforderlich, die durch den Einsatz der NMR-Technik gewonnen werden. Der nachfolgende Artikel beschreibt den Feuchtetransport in einer speziell für den Textilbeton entwickelten Feinbetonmatrix sowie den Einfluss verschiedener Modifikationsstoffe auf das Wasseraufnahmeverhalten des Betons. / Durability tests of textile reinforced concrete revealed a loss of strength of the AR-glass reinforcement due to glass corrosion effected by the alkalinity and moisture content of the concrete. In order to reduce this strength loss of AR-glass in cementitious matrices, polymers can be used for concrete modification. The aim of the polymer addition is to reduce the amount of capillary water absorption of the matrix, which reduces the amount of free alkalies closed to the reinforcement. In order to evaluate the effect of the concrete matrix on the durability of TRC, it is necessary to determine the moisture content as functions of time and depth. This data can be obtained by the use of nuclear magnetic resonance (NMR) technique. This paper deals with the moisture transport in a finegrained concrete matrix especially developed for the use in TRC as well as the influence of polymer addition on the water absorption properties of the concrete matrix.

Esta dissertação apresenta um estudo da deformação permanente de misturas asfálticas à luz dos resultados de ensaios de fluência por compressão uniaxial estática e dinâmica. Para isso, um programa experimental completo foi desenvolvido combinando fatores relacionados às misturas asfálticas e às condições de ensaio. Foram produzidos corpos de prova de misturas asfálticas densas tipo CAUQ com asfalto convencional (CAP 50/70) e com asfalto modificado com polímero SBS (CAP 50/70+SBS), variando o volume de vazios em dois níveis, 4 e 7%, e a presença de aditivo em dois níveis, sem e com cal hidratada. Os corpos de prova foram submetidos a ensaios de fluência com carregamentos estático e dinâmico em dois níveis de tensões, 0,1 MPa e 0,4 MPa, e em duas temperaturas diferentes, 40 e 50ºC. Essas condições do programa experimental permitiram observar o efeito do modificador SBS, da presença da cal e do volume de vazios nas misturas asfálticas, e entender o efeito da temperatura, do nível de tensão e do tipo de carregamento no comportamento de cada tipo de mistura asfáltica. Os resultados indicam que (i) a adição da cal promoveu redução de deformação acumulada somente nas misturas com ligante convencional (CAP 50/70); (ii) as misturas com volume de vazios de 7% apresentam maiores acúmulos de deformação permanente independente da presença de cal, do tipo de carregamento e da temperatura do ensaio, sendo maiores para a mistura asfáltica com CAP 50/70; (iii) as misturas com ligante modificado se mostraram menos sensíveis às variações da temperatura e do nível de tensão; (iv) e a melhora das características das misturas com asfalto modificado com polímero é detectada somente a partir de ensaios dinâmicos. / This paper presents a study of rutting on hot mixture asphalt (HMA) by means of static and dynamic creep tests. A full factorial experiment was developed considering factors related to HMA and to the test conditions. It was produced HMA (unmodified (CAP 50/70) and SBS modified binders) specimens at two different air voids (4 and 7%) and with or without hydrated lime. The specimens were submitted to static and dynamic creep tests at two stress levels, 0,1 MPa e 0,4 MPa, and two temperatures, 40 e 50ºC. These conditions of the experimental program allowed to observe the effects of the modifier SBS, the presence of the lime and the air voids in HMA, and to understand the effects of the temperature, stress and the type of loading on the behavior of each type of asphalt mix. The results indicate that (i) the addition of lime promoted reduction of accumulative deformation only in mixtures with conventional binder (CAP 50/70), (ii) mixtures with 7% air voids showed greater accumulation of permanent deformation regardless of presence of lime, the type of load and temperature of the test, mainly for the conventional HMA, (iii) the Polymer Modified Asphalt Hot Mix Asphalt (PMA-HMA) were less sensitive to temperature and the stress variation (iv) the improvement of the polymer modified asphalt mixture characteristics (PMA-HMA) were detected only on dynamic load conditions.

Master´s thesis deals with the study properties of polymer modified mortars using recycled glass and is divided into two parts, theoretical and practical. In the theoretical part has been expert search which deals with polymer modified mortars using recycled glass. On the basis of this information has been formulate practical part, which focused on the study properties of mortars depending on the time period and environment.

Untersuchungen zur Dauerhaftigkeit von ARGlasbewehrung im Textilbeton haben gezeigt, dass durch die Alkalität des Betons in Verbindung mit Feuchtigkeit eine Glaskorrosion hervorgerufen wird, die im Laufe der Zeit zu Festigkeitsverlusten des Glases führt. Eine Möglichkeit, die durch die Glaskorrosion verursachten Festigkeitsverluste zu reduzieren, stellt die Polymermodifikation des Betons dar. Durch die Polymerzugabe wird die Wasseraufnahme der Feinbetonmatrix reduziert, dadurch sinkt der Gehalt an gelösten Alkalien im Bereich der Bewehrung. Um den Einfluss verschiedener Feinbetonmatrices auf die Dauerhaftigkeit von Textilbeton beurteilen zu können, sind u. a. zeit- und tiefenabhängige Informationen zur Feuchteverteilung erforderlich, die durch den Einsatz der NMR-Technik gewonnen werden. Der nachfolgende Artikel beschreibt den Feuchtetransport in einer speziell für den Textilbeton entwickelten Feinbetonmatrix sowie den Einfluss verschiedener Modifikationsstoffe auf das Wasseraufnahmeverhalten des Betons. / Durability tests of textile reinforced concrete revealed a loss of strength of the AR-glass reinforcement due to glass corrosion effected by the alkalinity and moisture content of the concrete. In order to reduce this strength loss of AR-glass in cementitious matrices, polymers can be used for concrete modification. The aim of the polymer addition is to reduce the amount of capillary water absorption of the matrix, which reduces the amount of free alkalies closed to the reinforcement. In order to evaluate the effect of the concrete matrix on the durability of TRC, it is necessary to determine the moisture content as functions of time and depth. This data can be obtained by the use of nuclear magnetic resonance (NMR) technique. This paper deals with the moisture transport in a finegrained concrete matrix especially developed for the use in TRC as well as the influence of polymer addition on the water absorption properties of the concrete matrix.

The target of the ‘Green Overlays’ research was a cost effective, minimal disruption, sustainable and environmentally friendly alternative to the wholesale demolition, removal and complete reconstruction of the existing structural concrete pavement. The important problem of flexural resistance for strengthening concrete pavements with structural overlays has been scrutinised. A new mix design method for steel fibre reinforced, roller compacted, polymer modified, bonded concrete overlay has been proposed. The mixes developed were characterized of high flexural strength and high bond strength with the old concrete substrate. ‘Placeability’ and ‘compactability’ of the mix were two dominant issues during laboratory investigation. An innovative approach for establishing the relationship between Stress and Crack Face Opening Displacement for steel fibre reinforced concrete beams under flexure was developed. In addition, a new and simple method for calculating the interfacial Strain Energy Release Rate of both, a two-dimensional specimen and a three-dimensional model of the overlay pavement system were developed. This method can be readily and easily used by practicing engineers. Finally, a new test specimen and its loading configuration for measuring interfacial fracture toughness for concrete overlay pavements were established. The interfacial fracture toughness of a composite concrete beam, consisted of steel fibre-reinforced roller compacted polymer modified concrete bonded on conventional concrete and undergoing flexure, was assessed. In summary, this thesis presents four key findings: A new mix design method for steel fibre-reinforced roller compacted polymer modified concrete bonded on conventional concrete. A new method for establishing the fibre bridging law by an inverse analysis approach. A new, simplified method for calculating strain energy release rate at the interface of a composite beam. A new, innovative technique for calculating strain energy release rate at the interface of an overlaid pavement. The thesis contains a plethora of graphs, data-tables, examples and formulae, suitable for future researchers.

O objetivo desta pesquisa foi contribuir para o entendimento sobre a suscetibilidade ao dano por umidade de misturas asfálticas densas à luz dos ensaios da ASTM D 4867 e AASHTO T 283. Para isso, foi desenvolvido um programa experimental completo que considerou a variação, em dois níveis, dos seguintes fatores: tipo de asfalto (CAP 50/70 e CAP 50/70+SBS), presença de aditivo (sem e com cal) e modo de preparo (envelhecimentos em curto e em longo prazos). O programa experimental resultou em 8 tipos de misturas asfálticas (condições experimentais) que foram caracterizadas em suas propriedades originais e após um condicionamento térmico composto de uma fase de congelamento (-18º C por 16 horas) e uma fase de descongelamento (60º C por 24 horas). A partir das análises dos resultados foi possível constatar que (i) nenhuma mistura testada foi considerada suscetível ao dano por umidade, mas a relação de resistência à tração das misturas com CAP 50/70 de ambos os métodos se encontraram no limiar dos valores limites; (ii) as misturas com asfalto modificado, em geral, apresentaram maiores valores de módulo de resiliência e resistência à tração e foram mais resistentes à ação da água; (iii) a adição de cal não promoveu mudanças notáveis nas propriedades originais, no entanto contribuiu para a manutenção ou para o aumento da resistência ao dano por umidade; (iv) os envelhecimentos em curto e longo prazos dos métodos da ASTM e da AASHTO não provocaram mudanças importantes nas propriedades originais e após o condicionamento as misturas testadas exibiram tendências de comportamentos similares. / This research presents a contribution to understanding hot mix asphalt (HMA) moisture damage susceptibility according to ASTM D 4867 and AASHTO T 283 tests. A full factorial experiment design was carried out considering the factor variations, on two levels: asphalt type (CAP 50/70 and CAP 50/70+SBS), additive presence (with or without hydrated lime) and mixture procedure (short and long term aging). The experimental program resulted in 8 types of asphalt mixes (experimental conditions) which were characterized by the original properties and after a thermal conditioning wich consisted of a freezing phase (-18 °C for 16 hours) and a thawing phase (60 °C for 24 hours). Findings indicate that (i) no one mix was considered susceptible to moisture damage, however the ITR (indirect tensile ratio) of the CAP 50/70 mixes resulted ITR near to protocol admissible values; (ii) in general, CAP 50/70+SBS mixes presented higher resilient modulus, indirect tensile strength and indirect tensile ratio values, (iii) the addition of hydrated lime did not show remarkable changes in original properties, nevertheless it contributed for maintaining or increasing the moisture damage resistance; (iv) short and long term aging procedures (ASTM and AASHTO) did not cause important changes in original properties and after conditioning the mixes showed similar behavior tendencies.

Esta pesquisa tem como objetivo estudar a relação entre parâmetros de compactação e de deformação permanente à luz dos ensaios de compactação giratória Superpave ® e de ensaios de compressão uniaxial estática e dinâmica. Foram estudadas 8 misturas asfálticas com a mesma granulometria (Faixa C) e tipo de agregado mineral (granito) porém variou-se o ligante asfáltico (CAP 50/70 e CAP 50/70+SBS), o volume de vazios (4% e 7%) e a adição de cal hidratada. A partir dos resultados do ensaio de compactação observou-se que a inclinação das curvas de compactação das misturas compactadas a 7% foram mais acentuadas do que as de 4% e os parâmetros incidentais deste ensaio foram sensíveis à presença de cal e à variação do asfalto das misturas testadas. Quanto aos resultados dos ensaios de creep estático e dinâmico, notou-se que as misturas com Vv de 4% e as com asfalto modificado apresentam menor suscetibilidade à deformação permanente, no entanto, essas vantagens do asfalto modificado foram observadas somente nos ensaios de creep dinâmico. No que se refere às relações entre os parâmetros de compactação e de deformação permanente, os ajuste não se mostraram promissores como verificado pela qualidade dos ajustes (R2) exceto para algumas relações com CDI e TDIm. / This research aims to study relations between compaction and permanent deformation by means of Superpave® gyratory compaction and static and dynamic creep tests. Thus, eight asphalt mixtures were evaluated which were composed by same type (granite) and gradation (dense) of mineral aggregate but two types of asphalt binder (Pen 50/70 AC and Pen 50/70+SBS AC), two different levels of air voids (4% and 7%) and the addition of hydrated lime. Compaction results indicated that curve slopes of 7% air void asphalt mixtures were stronger than the 4% ones, and compaction parameters were sensitive to lime addition and asphalt type change. Static and dynamic creep test results indicated that 4% air void and modified asphalt mixtures presented lower susceptibility to rutting, but, these modified asphalt advantages were observed only in dynamic creep tests. In regard to relation between compaction and rutting parameters, linear models did not fit accurately, excepting some CDI and TDIm ones.