Sewer and oil pipeline spillage issues have become major causes of pollution in urban and rural areas usually caused by blockages in the water storage and drainage system, and oil spillage of underground oil pipelines. An effective way of avoiding this problem will be by deploying some mechanism to monitor these installations at each point in time and reporting unusual liquid activity to the relevant authorities for prompt action to avoid a flooding or spillage occurrence. This research work presents a low cost energy efficient liquid level monitoring technique using Radio Frequency Identification Technology. Passive UHF RFID tags have been designed, modelled and optimized. A simple rectangular tag, the P-shaped tag and S-shaped tag with UHF band frequency of operation (850-950 MHz) has been designed and modelled. Detailed parametric analysis of the rectangular tag is made and the optimised design results analysed and presented in HFSS and Matlab. The optimised rectangular tag designs are then deployed as level sensors in a gully pot. Identical tags were deployed to detect 4 distinct levels in alternate positions and a few inches in seperation distance within the gully pot height (Low, Mid, High and Ultra high). The radiation characteristic of tag sensors in deployment as modelled on HFSS is observed to show consistent performance with application requirements. An in-manhole chamber antenna for an underground communication system is analysed, designed, deployed and measured. The antenna covers dual-band impedance bandwidths (i.e. 824 to 960 MHz, and 1710 to 2170 MHz). The results show that the antenna prototype exhibits sufficient impedance bandwidth, suitable radiation characteristics, and adequate gains for the required underground wireless sensor applications. Finally, a Linearly Shifted Quadrifilar Helical Antenna (LSQHA) designed using Genetic Algorithm optimisation technique for adoption as an RFID reader antenna is proposed and investigated. The new antenna confirms coverage of the RFID bandwidth 860-960 MHz with acceptable power gain of 13.1 dBi. / Petroleum Technology Development Fund (PTDF) and National Space Research and Development Agency (NASRDA).

Dealing with the electromagnetic issue might bring a sort of discontinuous and nondifferentiable regions. Thus, it is of great interest to implement an appropriate optimisation approach, which can preserve the computational resources and come up with a global optimum. While not being trapped in local optima, as well as the feasibility to overcome some other matters such as nonlinear and phenomena of discontinuous with a large number of variables. Problems such as lengthy computation time, constraints put forward for antenna requirements and demand for large computer memory, are very common in the analysis due to the increased interests in tackling high-scale, more complex and higher-dimensional problems. On the other side, demands for even more accurate results always expand constantly. In the context of this statement, it is very important to find out how the recently developed optimization roles can contribute to the solution of the aforementioned problems. Thereafter, the key goals of this work are to model, study and design low profile antennas for wireless and mobile communications applications using optimization process over a computational electromagnetics numerical solution. The numerical solution method could be performed over one or hybrid methods subjective to the design antenna requirements and its environment. Firstly, the thesis presents the design and modelling concept of small uni-planer Ultra- Wideband antenna. The fitness functions and the geometrical antenna elements required for such design are considered. Two antennas are designed, implemented and measured. The computed and measured outcomes are found in reasonable agreement. Secondly, the work is also addressed on how the resonance modes of microstrip patches could be performed using the method of Moments. Results have been shown on how the modes could be adjusted using MoM. Finally, the design implications of balanced structure for mobile handsets covering LTE standards 698-748 MHz and 2500-2690 MHz are explored through using firefly algorithm method. The optimised balanced antenna exhibits reasonable matching performance including near-omnidirectional radiations over the dual desirable operating bands with reduced EMF, which leads to a great immunity improvement towards the hand-held. / General Secretariat of Education and Scientific Research Libya

The proliferation of modern wireless networks increases demand for high capacity and throughput in order to provide faster, more robust, efficient and broadband services to end users. Mobile WiMAX and LTE are examples of such networks in which for some cases they have exposed limited connectivity due to harsh environment. Relay stations are preferred to overcome problems of weak or no access for such network devices, that are placed in specific positions to maintain high quality of data transfer at low cost and provide the required connectivity anywhere anytime. These stations should be equipped with an antenna system capable of establishing communication between base station (backhaul link) and end users (access link). This thesis focuses on the design and development of a new antenna system that is suitable for a relay-based wireless network. Planar geometries of microstrip patch antennas are utilized. The antenna system comprises two antenna modules: a new design of a single antenna for access link and a new design of an antenna array for backhaul link realization. Both antenna specifications are compatible with the IEEE802.16j protocol standard. Hence, relay station should be capable of pointing its radiation pattern to the base station antenna, thus to achieve the desired radiation pattern of the relay station, a new beam-forming module is proposed, designed and developed to generate the proper radiation pattern. The beam-forming module incorporating digital phase shifters and attenuator chips is fabricated and tested. The optimization process using the Least Mean Square (LMS) algorithm is considered in this study to assign the proper phase and amplitude that is necessary to each radiation element excitation current, to produce the desired steered radiation pattern. A comprehensive study on the coupling effects for several relative positions between two new backhaul and access link antenna elements is performed. Two new antenna configurations for coupling reduction are tested and the simulated and measured results in terms of antenna radiation performances were compared and commented.

Libyan Ministry of Higher Education. / The full text will be available at the end of the embargo: 28th Nov 2024 / Subtitle: Simulation and Measurement of Reconfigurable Antennas for Cognitive Radio, UWB Applications, Investigation of Antenna Gain and Efficiency, Frequency Tuneable Range, Antenna Radiation Performance and Antenna Design Optimization using Parametric Studies as well as using MIMO antenna for wireless body area networks

The proliferation of modern wireless networks increases demand for high capacity and throughput in order to provide faster, more robust, efficient and broadband services to end users. Mobile WiMAX and LTE are examples of such networks in which for some cases they have exposed limited connectivity due to harsh environment. Relay stations are preferred to overcome problems of weak or no access for such network devices, that are placed in specific positions to maintain high quality of data transfer at low cost and provide the required connectivity anywhere anytime. These stations should be equipped with an antenna system capable of establishing communication between base station (backhaul link) and end users (access link). This thesis focuses on the design and development of a new antenna system that is suitable for a relay-based wireless network. Planar geometries of microstrip patch antennas are utilized. The antenna system comprises two antenna modules: a new design of a single antenna for access link and a new design of an antenna array for backhaul link realization. Both antenna specifications are compatible with the IEEE802.16j protocol standard. Hence, relay station should be capable of pointing its radiation pattern to the base station antenna, thus to achieve the desired radiation pattern of the relay station, a new beam-forming module is proposed, designed and developed to generate the proper radiation pattern. The beam-forming module incorporating digital phase shifters and attenuator chips is fabricated and tested. The optimization process using the Least Mean Square (LMS) algorithm is considered in this study to assign the proper phase and amplitude that is necessary to each radiation element excitation current, to produce the desired steered radiation pattern. A comprehensive study on the coupling effects for several relative positions between two new backhaul and access link antenna elements is performed. Two new antenna configurations for coupling reduction are tested and the simulated and measured results in terms of antenna radiation performances were compared and commented.

The rapidly growing demand for UWB as high data rates wireless communications technology, since the Federal Communications Commission (FCC) allocated the bandwidth of UWB from 3.1GHz to 10.6 GHz. Antenna also plays an essential role in UWB system. However, there are some difficulties in designing UWB antenna as compared to narrowband antenna. The primary requirement of UWB antennas is be able to operate over frequencies released by the FCC. Moreover, the satisfaction of radiation properties and good time domain performance over the entire frequency range are also necessary. In this thesis, designing and analysing printed crescent shape monopole antenna, Planar Inverted F-L Antenna (PIFLA) and Planar Inverted FF Antenna (PIFFA) are focused. A Planar Inverted FF Antenna (PIFFA) can be created to reduce the potential for interference between a UWB system and other communications protocols by using spiral slot. The antennas exhibits broadside directional pattern. The performances such as return loss, radiation pattern and current distribution of the UWB antennas are extensively investigated and carried out. All the results have been demonstrated using simulation and experimentally whereby all results satisfy the performance under - 10dB point in the bandwidth of UWB. In addition the miniaturization of MIMO/diversity Planar Inverted-F antenna (PIFA) which is suitable for pattern diversity in UWB applications is presented. This antenna assembly is formed by two identical PIFAs, a T-shaped decoupling structure which connects the two PIFAs and a finite ground plane with a total compact envelope dimension of 50 x 90 x 7.5mm³. The radiation performance of the proposed MIMO antenna was quite encouraging and provided an acceptable agreement between the computed and measured envelope correlation coefficient and channel capacity loss.

This thesis describes an electrically thin surface used for electromagnetic applications in the microwave regime. The surface is free-standing and its primary purpose is to modify the phase distribution, or the phase and amplitude distribution of electromagnetic fields propagating through it: it is called phase shifting surface (PSS) in the first case, and phase and amplitude shifting surface (PASS) in the second case. For practical applications, the surface typically comprises three or four layers of metallic patterns spaced by dielectric layers. The patterns of the metallic layers are designed to locally alter the phase (and amplitude in the case of the PASS) of an incoming wave to a prescribed set of desired values for the outgoing wave. The PSS/PASS takes advantage of the reactive coupling by closely spacing of the metallic layers, which results in a larger phase shift range while keeping the structure significantly thin. The PSS concept is used to design components such as gratings and lens antennas which are presented in this document. The components are designed for an operating frequency of 30 GHz. The PSS phase grating gives high diffraction efficiency, even higher than a dielectric phase grating. Several types of lens antennas are also presented, which show comparable performance to that of a conventional dielectric plano-hyperbolic lens antenna with similar parameters. The PASS concept is used in a beam shaping application in which a flat-topped beam antenna is designed. This work demonstrates the potential for realising thin, lightweight and low-cost antennas at Ka band, in particular for substituting higher-gain antenna technologies such as conventional dielectric shaped lens antennas.

This thesis describes an electrically thin surface used for electromagnetic applications in the microwave regime. The surface is free-standing and its primary purpose is to modify the phase distribution, or the phase and amplitude distribution of electromagnetic fields propagating through it: it is called phase shifting surface (PSS) in the first case, and phase and amplitude shifting surface (PASS) in the second case. For practical applications, the surface typically comprises three or four layers of metallic patterns spaced by dielectric layers. The patterns of the metallic layers are designed to locally alter the phase (and amplitude in the case of the PASS) of an incoming wave to a prescribed set of desired values for the outgoing wave. The PSS/PASS takes advantage of the reactive coupling by closely spacing of the metallic layers, which results in a larger phase shift range while keeping the structure significantly thin. The PSS concept is used to design components such as gratings and lens antennas which are presented in this document. The components are designed for an operating frequency of 30 GHz. The PSS phase grating gives high diffraction efficiency, even higher than a dielectric phase grating. Several types of lens antennas are also presented, which show comparable performance to that of a conventional dielectric plano-hyperbolic lens antenna with similar parameters. The PASS concept is used in a beam shaping application in which a flat-topped beam antenna is designed. This work demonstrates the potential for realising thin, lightweight and low-cost antennas at Ka band, in particular for substituting higher-gain antenna technologies such as conventional dielectric shaped lens antennas.

En este trabajo de Tesis Doctoral se presenta una contribución al estudio de las modificaciones sufridas en los patrones de radiación ultrasónicos mediante el uso de elementos mecánicos acoplados al sensor, de tipo bocinas, y de distintas características físicas y geométricas, con el fin de conseguir que el nuevo patrón de radiación sea más adecuado para una determinada aplicación, y teniendo en cuenta las condiciones ambientales en las que se desarrolla la misma. / This Doctoral Thesis presents a contribution in the study of the modifications suffer by the radiation patterns due to the use of mechanical elements with different dimensions and characteristics, in order to obtain a new radiation pattern more suitable for a given application, which is developed in a determinated environmental conditions and they must be taken into account.

This thesis describes an electrically thin surface used for electromagnetic applications in the microwave regime. The surface is free-standing and its primary purpose is to modify the phase distribution, or the phase and amplitude distribution of electromagnetic fields propagating through it: it is called phase shifting surface (PSS) in the first case, and phase and amplitude shifting surface (PASS) in the second case. For practical applications, the surface typically comprises three or four layers of metallic patterns spaced by dielectric layers. The patterns of the metallic layers are designed to locally alter the phase (and amplitude in the case of the PASS) of an incoming wave to a prescribed set of desired values for the outgoing wave. The PSS/PASS takes advantage of the reactive coupling by closely spacing of the metallic layers, which results in a larger phase shift range while keeping the structure significantly thin. The PSS concept is used to design components such as gratings and lens antennas which are presented in this document. The components are designed for an operating frequency of 30 GHz. The PSS phase grating gives high diffraction efficiency, even higher than a dielectric phase grating. Several types of lens antennas are also presented, which show comparable performance to that of a conventional dielectric plano-hyperbolic lens antenna with similar parameters. The PASS concept is used in a beam shaping application in which a flat-topped beam antenna is designed. This work demonstrates the potential for realising thin, lightweight and low-cost antennas at Ka band, in particular for substituting higher-gain antenna technologies such as conventional dielectric shaped lens antennas.