O presente trabalho tem por objetivo avaliar o comportamento dos campos eletromagnéticos no interior de câmaras reverberantes de modos misturados através do método numérico TLM (Transmission Line Matrix). Inicialmente, apresenta-se uma descrição dos diversos tipos de câmaras aplicáveis na avaliação de desempenho de compatibilidade eletromagnética de equipamentos e sistemas elétricos, destacando-se suas principais características físicas e geométricas, com ênfase nas câmaras reverberantes. Os aspectos teóricos relacionados à descrição do método TLM são detalhados e sua aplicação na avaliação do ambiente eletromagnético das câmaras é então abordada. Diversos resultados são apresentados, considerando-se configurações pré-definidas de câmaras reverberantes, ressaltando-se a definição e cálculo de índices de mérito, bem como os principais aspectos relacionados à representação e definição de critérios adotados nas simulações destas. / The aim of this report is the evaluation of the behavior of electromagnetic fields inside reverberation chambers by means of Transmission Line Modeling (TLM). Initially, it is presented a description of several kinds of chambers applicable for electromagnetic compatibility tests followed by a more detailed description regarding reverberation chambers. Theoretical aspects of TLM method and its application for electromagnetic fields solution are covered. Some results are presented, considering pre-defined reverberation chambers configurations, highlighting some merit indicators and the main aspects adopted on its simulation.

This thesis covers the development of the Reverberation Chamber as a measurement tool for cell phone tests in electronic production. It also covers the development of the Scattered Field Chamber as a measurement tool for simulations of real propagation environments. The first part is a more ”general knowledge about Reverberation Chambers”-part that covers some important phenomena like unstirred power and position dependence that might occour in a small Reverberation Chamber used for cell phone tests. Knowing how to deal with these phenomenas, give the possibility to use the chamber as a measurement tool for production tests even though it is too complex for a simple test of the antenna function. The second part shows how to alter some important propagation parameters inside the chamber to fit some real world propagation environments. The 3D plane wave distribution, the polarization and the amplitude statistics of the plane waves are all altered with simple techniques that are implementable all together. A small, shielded anechoic box with apertures is used to control 3D plane wave distribution and polarization. Antennas that introduce unstirred power in the chamber are used to control the statistics.

Ce travail porte sur les techniques de mesure des champs en cavité électromagnétique et plus précisément en chambre réverbérante. En raison de la perturbation induite sur la distribution du champ au sein d'une cavité résonante par la présence d'un objet, les techniques de mesure de champ classiques utilisant une antenne souffrent d'une précision limitée. Par conséquent, nous proposons une nouvelle technique de mesure de la distribution du champ électrique basée sur la théorie des perturbations. Elle consiste à mesurer les variations de la fréquence de résonance de la cavité pour chaque position de l'élément perturbateur introduit dans la cavité, puis à en déduire la variation de l'amplitude du champ électrique. Le choix de la forme de l'objet perturbateur, de ses dimensions et de son matériau constitutif est effectué à partir des résultats des simulations et des mesures dans un cas canonique, de façon à adapter le banc de mesure au cas étudié. Cette technique de mesure est ensuite appliquée avec succès au cas d'une chambre réverbérante équipée d'un brasseur de modes, ainsi qu'à des mesures de champ à l'intérieur d'un boitier inséré dans la cavité. Cette approche a permis, via un post-traitement basé sur l'utilisation de l'algorithme MUSIC, de déterminer avec une grande précision les directions d'arrivée des champs dans la chambre réverbérante / This work deals with field measurement techniques in large electromagnetic enclosures namely reverberation chambers. Due to the perturbation of the field distribution within a resonant cavity due to the presence of an introduced object, conventional field measurement techniques employing an antenna suffer from a limited accuracy. Therefore we propose a new measurement technique of the electric field distribution based on the perturbation theory; it consists of a measure of the cavity resonant frequency variation when displacing a small perturbing object within the cavity, and leads to the electric field distribution. The choice of the perturbing object shape, dimension and material is discussed with the help of simulation and measurement results in a canonical case in order to adapt the measurement setup to the studied case. This technique is then successfully employed in a reverberation chamber equipped with a mode stirrer, as well as to measure the field within a metallic box placed in the cavity. Using a post-processing based on MUSIC algorithm, this approach has permitted to determine accurately the field directions-of-arrival in the reverberation chamber

Die Elektromagnetische Verträglichkeit (EMV) betrachtet die Fähigkeit eines elektrischen Gerätes, in seiner elektromagnetischen Umgebung störungsfrei zu funktionieren, ohne diese dabei unzulässig zu stören. Zur Prüfung der Elektromagnetischen Verträglichkeit werden verschiedene Messumgebungen verwendet. Die Messung der strahlungsgebundenen Störfestigkeit und Störaussendung kann zum Beispiel in einer Modenverwirbelungskammer (MVK) erfolgen. Bei der Störfestigkeitsmessung wird der Prüfling einem externen Prüffeld ausgesetzt und untersucht, ob dieser die definierten Kriterien für einen störungsfreien Betrieb erfüllt. Für das Prüffeld muss vor der Messung nachgewiesen werden, dass die Anforderungen an dessen Homogenität eingehalten werden. Einen entscheidenden Einfluss auf die Homogenität des Prüffeldes hat der sogenannte Rührer. Bei einer MVK handelt es sich prinzipiell um einen Hohlraumresonator, in den ein mechanischer Rührer, d.h. ein elektrisch großer, drehbarer Streukörper integriert wird. Durch die Drehung des Rührers verändert sich die Feldverteilung in der MVK, was auch als Verwirbelung bezeichnet wird. Prinzipiell ergibt sich für jede Stellung des Rührers ein inhomogenes Feld mit lokalen Minima und Maxima. Ein Ziel bei der Verwendung von Modenverwirbelungskammern ist es, mit Hilfe geeigneter Verfahren Rührerstellungen zu finden, deren Feldverteilungen in Überlagerung ein möglichst homogenes Prüffeld erzeugen. Zum Lehrstuhl für Theoretische Elektrotechnik und Elektromagnetische Verträglichkeit der Technischen Universität Dresden gehört seit 2010 eine Modenverwirbelungskammer. Die Charakterisierung dieser MVK sowie eine weiterführende Untersuchung zur Wahl der Rührerstellungen bilden die Schwerpunkte der vorliegenden Arbeit. / In 2010 the Chair of Electromagnetic Theory and Compatibility of Technical University Dresden could extend its laboratories by a reverberation chamber with the dimensions 5.3 m, 3.7m and 3.0 m. Since then, a detailed characterisation of the chamber as well as further investigations have been the main emphasis of the authors research. The submitted doctoral thesis presents the obtained results. With the design, the fundamentals of operation and further characterisation of the reverberation chamber, given in Chapter 1 and 2, it aims to give an introduction and better understanding of reverberation chambers. On this basis, the authors research focused on methods for determining the independent stirrer positions in reverberations chambers. The results of the investigations are presented and summarised in chapter 3. One scope of Electromagnetic Compatibility are radiated immunity measurements. Besides the GTEM cell and the anechoic chamber the reverberation chamber gains in importance as an alternative measurement environment. A reverberation chamber is a shielded room with reflecting walls and one or more integrated mechanical stirrers. By rotating the stirrer the spatial boundary conditions for the electromagnetic field quantities are altered. The resulting change of the spatial field distribution depends on the location within the chamber and the geometry of the stirrer. Each stirrer position yields an inhomogeneous field distribution created by interfering waves. A general aim is to find a set of stirrer positions, whose superimposed field distributions create a more uniform test field. In practice, the given requirements for the homogeneity of the test field shall, with regards to an optimisation of measurement time, be realized with a minimum number of stirrer positions. In this context the term ’independent stirrer positions’ was established and describes stirrer positions, whose field distributions are linearly uncorrelated and therefore assumed to be practical for creating a more homogeneous test field using only a minimal number of stirrer positions. A general method for determining the number of independent stirrer positions in reverberation chambers is presented. The method uses a certain number of measurement positions in a defined test volume in order to characterize the spatial field distribution inside the chamber. Using the Pearson correlation coefficient the field distributions of the stirrer positions are tested for linear correlation and pairs of independent stirrer positions are determined. On this basis, cliques of pairwise independent stirrer positions are identified using appropriate algorithms. It is shown that the general method yields detailed information about the number and distribution of the independent stirrer positions and is therefore particularly suitable to evaluate other methods. Finally, the standard method according to IEC 61000-4-21 as well as selected alternative methods, that have been proposed in the past, are evaluated and compared based on the results of the general method.

Measurements in a reverberation chamber use spatially averaged squared pressure to calculate sound absorption, sound power, and other sound measurements. While a reverberation chamber provides an approximation of a diffuse sound field, variations in the measurements introduce uncertainty in measurement results. Room qualification procedures require a sufficient number of source-receiver locations to obtain suitable measurements. The total acoustic energy density provides greater spatial uniformity than squared pressure, which requires fewer source-receiver positions to produce similar or better accuracy in measurement results. This paper explores the possibility of using energy density in place of squared pressure, using methods outlined in current ISO standards, by describing several experimental and analytical results.

Звукоизоляция материалов является ключевым вопросом в оценке конкурентоспособности на строительном рынке. Поэтому, для удовлетворения новым и перспективным нормам по шуму необходимы прорывные решения, основанные на глубоких научных исследованиях, создание работоспособных методов и методик оценки звукоизоляции строительных материалов и повышения коэффициента звукопоглощения. Для реализации этих целей требуются научно-исследовательские лаборатории, имеющие достаточную материально-техническую базу, удовлетворяющие требованиям стандартов. Главной целью диссертации является создание акустической реверберационной камеры для испытаний строительных изделий и конструкций на звукоизоляцию. Также диссертация посвящена проведению первичной аттестации камеры. / Soundproof materials is a key issue in assessing competitiveness in the construction market. Therefore, to meet new and promising noise norms, breakthrough solutions based on in-depth scientific research, the creation of efficient methods and techniques for assessing the sound insulation of building materials and increasing the sound absorption coefficient are necessary. To achieve these goals, research laboratories that have sufficient material and technical facilities that meet the requirements of standards are required. The main goal of the dissertation is to create an acoustic reverberation chamber for testing construction products and structures for soundproofing. Also the Thesis is devoted to the primary certification of the camera.

<p>The aim of the research work presented here, is to contribute to the adaptation of electronic packaging towards the needs of high frequency applications. As the field of electronic packaging stretches over several very different professional areas, it takes an interdisciplinary approach to optimize the technology of electronic packaging. Besides this, an extensive knowledge of industrial engineering should be an essential part of this undertaking to improve electronic packaging. Customary advances in technology are driven by new findings and a continuous development of processes in clearly defined fields. However, in the field of the higher levels of the interconnection hierarchy, that is external to the chip level interconnections and chip packaging, it is supposed that a wide combination of disciplines and technical creativity, instead of advanced technology in a special area should produce most added value.</p><p>The thesis is divided into five areas, interlinked by the overall aim of there advantages to the common goal. These areas are the Printed Wiring Board (PWB) technology, PWB connections using flexible printed circuit boards, multiconductor cable connections, shielded enclosures and the related EMC issues, and finally the cooling of electronics. A central issue was to improve the shielded enclosures to be effective also at very high frequencies; it will be shown that shielded enclosures without apertures can cope with frequencies up to and above 15 GHz. Due to this enclosure without apertures, it was necessary to develop a novel cooling structure. This cooling structure consists of a heat sink where the PCB’s are inserted in close contact to the cooling fins on one side, whereas the other side of the heat sink is cooled by forced ventilation. The heat transfer between these parts is completely inside the same body. Tests carried out on a prototype have shown that the performance of the cooling structure is satisfactory for electronic cooling.</p><p>Another problem area that is addressed are the interconnect problems in high frequency applications. Interconnections between parts of a local electronic system, or as within the telecom and datacom field between subscribers, are commonly accomplished by cable connections. In this research work multiconductor cables are examined and a patented novel cable-connector for high frequency use is presented. Further, an experimental complex soldering method between flexible printed circuits boards and rigid printed circuits boards, as part of connections between PCBs, is shown. Finally, different sectors of the PCB technology for high frequency applications are scrutinized and measurements on microstrip structures are presented.</p>

Halmstad University is currently equipped with an Echo-free chamber to perform EMC testing, but no reverberation chamber. The construction of a paddle stirrer to be utilized in Halmstad University would drastically reduce the time required to perform EMC testing, since reverberation chambers are more efficient than Echo-free chambers for these kind of tests. The goal of this project was to design and develop a paddle stirrer structure and a control system able to rotate the stirrer to specific repeatable absolute angles with an accuracy of a tenth of a degree,holding a mass up to 70kg and rotating a mass up to 20 kg distributed on a 1x1m surface. To achieve this goal the system has been designed using a metal base structure, bearings to hold the lower shaft in its axes reducing its friction, a stepper motor connected to the gears to increase its holding torque, a magnetic rotary encoder and a control system with a double feedback from interrupts and from the encoder to improve the accuracy and reliability of the system. The resultis a completely working prototype, which fulfils all the requirements except for the speed. The target speed has not been achieved due to the insufficient holding torque of the available stepper motor. / Halmstad Högskola är för närvarande utrustad med en Ekofri kammare för att utföra EMCtestning, men ingen modväxlande kammare. Konstruktionen av en paddle-omrörare för användning i Halmstad Högskola skulle drastiskt minska tiden som krävs för att utföra EMC-testning, eftersom modväxlande kammaren är effektivare än en ekofri kammare för dessa typer av tester.Målet med detta projekt var att designa och utveckla en paddle-omrörare, både strukturen samt ett styrsystem som kan rotera den till specifika repeterbara absoluta vinklar med en noggrannhet av en tiondel av en grad, hantera en massa upp till 70 kg och rotera en massa upp till 20 kg fördelad på en 1x1m yta. För att uppnå detta mål har systemet konstruerats med en basstruktur gjord av metall, lager har placerats i axeln för att reducera friktion, en stegmotor är anslutentill kugghjul för att öka vridmomentet, en magnetisk roterande sensor och ett styrsystem med en dubbel återkoppling från interrupts och från sensorn för att förbättra systemets noggrannhet och tillförlitlighet. Resultatet är en helt fungerande prototyp som uppfyller alla krav, förutom hastigheten. Målhastigheten har inte uppnåtts på grund av otillräckligt vridmoment hos stegmotorn.

Les mesures utilisées actuellement en chambres anéchoïque, pour la caractérisation de la surface équivalente radar (SER) sont généralement perturbées, en particulier en basse fréquence lorsque les parois de la chambre génèrent des trajets multiples. En basse fréquence l’épaisseur des matériaux absorbants devient faible devant la longueur d’onde et ceux-ci ne peuvent plus être considère comme parfaitement absorbants. Dans ce cas, le champ total incident sur la cible sous test est ainsi la somme du champ incident direct et des champs réfléchis par les parois. Basé sur le principe de retournement temporel qui permet de focaliser spatialement et temporellement une onde électromagnétique, l’objectif de la thèse est de présenter une nouvelle méthode d’imagerie microonde qui profite des degrés de liberté spatio-temporels de la propagation au sein d’un milieu diffusant afin de détecter une cible avec une haute résolution. / The currently used methods for radar cross section (RCS) measurements at low frequencies encounter several disturbing phenomena, such as the multipath propagation caused by reflections from the walls. Descending in frequency, the thickness of absorbent materials becomes small compared with the wavelength and they are no longer perfectly absorbent. Therefore, the total incident field on the target becomes the sum of the incident wave and the reflected waves from the walls of the chamber. Inspired by time reversal technique which allows spatial and temporal focusing of an electromagnetic wave, the objective of the thesis is to present a novel imaging method in the microwave range which benefits from the spatio-temporal degrees of freedom provided by the transmission through a random medium in order to detect a target with high resolution.

La chambre réverbérante à brassage de modes (CRBM) est une cavité métallique fermée surdimensionnée, équipée d’un brasseur de modes. Le brassage de modes rend le champ électromagnétique homogène et isotrope à l’intérieur de la CRBM (dans son volume utile). Cette thèse illustre tout d’abord une nouvelle méthode pour évaluer les performances d’un brasseur de modes (via le spectre Doppler). Ensuite, elle présente une nouvelle méthode permettant de mesurer la surface équivalente radar (SER) d’un objet canonique en utilisant la technique de fenêtrage temporel ou time-gating. Enfin, elle présente une nouvelle méthode permettant de mesurer le diagramme de rayonnement d’une antenne dans une cavité surdimensionnée via la technique de time-gating. / The reverberation chamber (RC) is an oversized closed metal cavity, equipped with a mode-stirrer. The mode stirring makes the electromagnetic field homogeneous and isotropic inside the RC (in its useful volume). This thesis illustrates firstly a new method for evaluating the performance of a mode-stirrer (via the Doppler spectrum). Then, it presents a new method for measuring the radar cross section (RCS) of a canonical object using the time-gating technique. Finally, it presents a new method for measuring the antenna radiation pattern in an oversized cavity via the time-gating technique.