Thesis (MEng.)--University of Stellenbosch, 2000. / ENGLISH ABSTRACT: The aim of the thesis was to investigate the use of flow destabilization methods, combined with permeate backflushing (BIF) or on their own, on flux recovery and maintenance in capillary UF membrane systems under cross-flow (XF) and dead-end (DE) operating conditions. Various hydraulic and mechanical methods have been used to remove the accumulated cake layer and improve steady state process flux. Permeate backflushing (B/F) is the most widely used but the drawbacks are loss of product and extensive down-time. In a pilot plant study for ultrafiltration of surface waters containing high NOM, turbidity and cation loads, the use of flow destabilization, or feed flow reversal (FFR) combined with cross-flow B/F was able to improve the normalised flux by 10.7 ± 3.4 %, compared with 3.2 ± 1.6 % improvement for BIF without FFR. When a second B/F included FFR, the flux improvement was 7.0 ± 2.0 % compared with 4.3 ± 2.5 % for a B/F without FFR. The hypothesis was proposed that the flow destabilization caused slight lifting of the oriented cake layer, while the cross-flow B/F was able to sweep the lifted cake out of the lumen. If the flow destabilization may be effected by a simple but effective and low-cost method, and if this flow destabilization may be combined with reverse flow for short durations, the "lift-and-sweep" approach will be the ideal method of maintaining process flux and increasing membrane life. Such a flow destabilization method, now named "reversepressure pulsing" (RIP), was developed. The method involves circulation of feed water in a recycle loop for 2 s to gain momentum, followed by closure of a fast-action valve upstream of the modules. The momentum of the water in the concentrate loop carries it into an air-filled feed accumulator, while concentrate and reverse-flow permeate (which also lifts the fouling layer) are discharged to the atmosphere using the recycle pump for 15 s. When the valve opens again, the air in the accumulator forces the water under pressure through the membrane lumens, causing a pressure pulse and flow perturbations that lift, shift and break up the fouling layer. During 3 such "lift-and-sweep" events, the cake is lifted and the debris is swept out of the lumen. Experimental results for uninterrupted dead-end filtration at a UF pilot plant using RIP only on a severely fouled membrane, indicated that the RIP increased the flux by 18.4 % and decreased the dP by 8.2 % over a 7.2 h period. The method is effective in removing the cake layer intermittently and no long-term flux decline occurred for a period of 555 h since the previous chemical cleaning. / AFRIKAANSE OPSOMMING: Die doel van die tesis was om die gebruik van vloei-destabiliserings metodes, alleen of gekombineer met permeaat-terugwas, op vloed-herwinning en instandhouding in kapillêre UF membraan-stelsels tydens kruisvloei en doodloop bedryf, te ondersoek. Verskeie meganiese en hidrouliese metodes word gebruik in membraan stelsels om die koeklaag op die membraan se oppervlak te verwyder en die gestadigde-toestand vloed te verbeter. Vanhierdie metodes word permeaat-terugwas die meeste gebruik, maar het sy nadele insluitend verlies van produk en produksietyd. In 'n loodsstudie vir die ultrafiltrasie van oppervlakwaters wat hoë beladings NOM, turbiditeit en katione bevat, is die waarneming gemaak dat kruisvloei terugwas met vloeidestabilisering (voerrigting-verandering) die genormaliseerde vloed met 10.7 ± 3.4 % kon verbeter, vergeleke met 'n 3.2 ± l.6 % verbetering sonder voerrigting-verandering. Vir 'n tweede terugwas was die verbetering 7.0 ± 2.0 % vergeleke met 4.3 ± 2.5 % sonder voerrigtingverandering. Die hipotese was voorgestel dat die vloei-destabilisering die geoiënteerde koeklaag van die oppervlak gelig het, en die kruisvloei terugwas die geligde koeklaag uit die lumen kon vee. Indien hierdie vloei-destabilisering bewerk kan word deur 'n eenvoudige maar effektiewe manier, en indien dit gekombineer kan word met terugvloei van produk vir kort tydperke, sal hierdie "lig-en-vee" benadering die ideale metode wees om die membrane se vloed te verbeter en leeftyd te verleng. So 'n vloei-destabiliseringsmetode, nou genoem "terugdruk-pulsering", is ontwikkel. Die metode behels die sirkuiering van voer-water vir 2 s in 'n hersirkulasielus om momentum op te bou, gevolg deur die toemaak van 'n snel-aksie klep stroom-op van die modules. Die water in die konsentraat-lus se momentum dra dit vorentoe tot in In lug-gevulde voer-akkumulator, terwyl konsentraat en terug-vloei permeaat (wat ook tot 'n mate die koeklaag lig) ook na die atmosfeer gewend word vir 15 s deur die hersirkulasiepomp. As die klep weer oopgaan, ontspan die lug in die akkumulator, en forseer die water daarin onder druk deur die membraan-lumens. Die druk-puls en vloei-perturbasies lig, skuif en breek die koeklaag op. Tydens 3 agtereenvolgende "lig-en-vee" aksies word die koeklaag effektief opgebreek en uit die lumen gevee. Eksperimentele uitslae vir ononderbroke doodloop bedryf op uitermate aangevuilde membrane van 'n ultrafiltrasie loodsaanleg toegerus met terugdruk-pulsering, het getoon dat die vloed met 18.4 % verbeter kon word en die dP met 8.2 % verminder kon word in slegs 7.2 h. Die metode breek die koeklaag effektief op, en geen langtermyn vloed-afname is waargeneem vir meer as 555 h sedert die vorige chemiese was-prosedure nie.

Thesis (MSc)-- Stellenbosch University, 2012. / ENGLISH ABSTRACT: Over the past two decades, field flow fractionation (FFF), as a polymer characterization technique, has become cutting edge technology. The demand for molar mass and size characterisation of complex polymer systems has increased, especially in cases where classical calibration techniques such as size exclusion chromatography (SEC) has shown several shortcomings. FFF is a technique resembling chromatography. It has several significant advantages over SEC, especially for the characterisation of ultrahigh molar mass (UHMM), branched and gel-containing polymers. In this study, polybutadienes, which often contain the abovementioned species, were analysed by SEC and asymmetric flow field flow fractionation (AF4). Both separation techniques were coupled to refractive index and multi-angle laser light scattering detection. Similarly, polyrotaxanes, which are polymers with complex and unique molecular architectures, were also investigated. Results showed that AF4 can explicitly be used as a superior tool over SEC. In the case of UHMM polybutadienes, much higher molar masses could be detected by AF4, due to the absence of shear degradation which is often encountered in SEC. Gel-containing species could be detected by AF4 as no filtering is required prior to injection. Abnormal retention behaviour, a phenomenon often encountered in UHMM branched polymers, was observed in SEC analysis of the polyrotaxanes materials. AF4 provided sufficient separation from low to high molar masses, without out any irregularities. / AFRIKAANSE OPSOMMING: Gedurende die afgelope twee dekades het veldvloeifraksionering (FFF) as ‘n polimeerkarakteriseringstegniek groot veld gewen. Die aanvraag na molekulêre massa en groottekarakterisering van komplekse polimeersisteme het toegeneem, veral in die gevalle waar klassieke kalibrasietegnieke soos grootte-uitsluitingschromatografie (SEC) etlike tekortkominge getoon het. FFF is ‘n tegniek soortgelyk aan chromatografie, en het voorheen bewys dat dit oor ‘n redelike aantal voordele bo SEC beskik, veral in die geval van ultrahoë molekulêre massa- (UHMM-), vertakte- en jelbevattende spesies. In die huidige studie is polibutadieenpolimere, wat dikwels bogenoemde spesies bevat, geanaliseer met behulp van SEC en onsimmetriese vloei-veldvloeifraksionering (AF4). Beide skeidingstegnieke is gekoppel aan ‘n brekingsindeks en multihoek-laserligverstrooiingsdetektors. Op dieselfde wyse is polirotaksane (polyrotaxanes) met komplekse molekulêre argitektuur bestudeer. Daar is bewys dat AF4 uitsluitlik gebruik kan word as ‘n meer geskikte tegniek bo SEC. Baie hoër molekulêre massas kon deur middel van AF4 vir UHMM polibutadieenpolimere raakgesien word as gevolg van die verminderde afbrekende degradasie wat dikwels voorkom met SEC. Jel-bevattende spesies is suksesvol geïdentifiseer met behulp van AF4 waartydens geen filtrering vir analise nodig was nie. Abnormale retensie was sigbaar tydens SEC analise van monsters van polirotaksane, wat dikwels voorkom in vertakte polimere. In teenstelling het AF4 bewys dat ‘n bevredigende skeiding van klein na groot molekulêre massas, sonder enige tekortkominge, moontlik is.

Thesis (MSc (Chemistry and Polymer Science))--University of Stellenbosch, 2007. / Electrodialysis is a method of water desalination which involves the separation of TDS through an ion-exchange membrane under a potential gradient. In this study it was attempted to reverse engineer the composite carbon ion-exchange membrane used in a prototype plant and electrochemically evaluate a prototype desalination cell. The influence of applied potential on the capacitance of the various electrode surfaces and possible electrode reactions was investigated. A model was also suggested to describe the conductivity through the membrane. The composition of composite carbon membranes were determined by compositional analysis using various analytical tools. Elemental analysis, done with PIXE and EDS, showed that the membranes contained chloride, fluoride, oxygen, carbon, and possibly hydrogen. With LC-MS and IR it was established that the membranes consisted of two polymers with no carbonyl or aromatic functional groups. After further thermal analysis the following possible compounds remained: hexafluoropropylene tetrafluoroethylene copolymer, polychlorotrifluoroethylene (PCTFE), polyoxyethylene oxide (PEO) and polyethylene glycol (PEG). This assessment is in good agreement with the contents of US patent 4,153, 661, which describes the composite membrane.

Thesis (MSc (Chemistry and Polymer Science))--University of Stellenbosch, 2005. / This study involves the fractionation and characterisation of three propyleneethylene random copolymers. The fractionation technique used in the study was temperature rising elution fractionation (TREF). The TREF fractions were subsequently analysed offline by crystallisation analysis fractionation (CRYSTAF), differential scanning calorimetry (DSC), 13C NMR, high-temperature gel-permeation chromatography (HT-GPC), and wide-angle x-ray diffraction (WAXD). The effect of the ethylene comonomer on the crystallisability of the propylene was investigated, along with the effect of the comonomer on the type of crystal phase formed during the crystallisation. The results show that the comonomer inhibits the crystallisation of the copolymer and that as the ethylene content increases, the crystallisation and melting points decrease. It was also shown that the higher the ethylene content, the more of the γ-phase crystal type is formed. The distribution of the comonomer throughout the copolymers was also investigated. The results show that there is an uneven distribution of the comonomer with most of the comonomer accumulating in the amorphous areas, and very little actually being incorporated in the crystalline regions. It was also observed that the fractions eluting at the highest temperatures had considerably higher polydispersities and lower molecular weights than the fractions eluting just before them. The highest temperature fractions also have lower melting and crystallisation temperatures than the preceding fractions. This has been attributed to a nucleation effect by the sand support used during the TREF fractionation.

90 leaves on CD format, preliminary i-ix pages and numbered pages 1-81. Includes bibliography, list of figures in color to pdf format (OCR). / Thesis (MSc (Chemistry and Polymer Science))--University of Stellenbosch, 2005. / ENGLISH ABSTRACT: The composition of petrochemical products obtained from Fischer Tropsch (FT) technologies is of the highest complexity possible and may contain thousands of components. Chemicals produced from FT feedstocks often contain trace level contaminants that can poison catalysts or that affect product performance in down-line processes. Single dimension GC analysis of these mixtures provides incomplete information because of lack of separation power. This study evaluates the separation power of heart-cut GC-GC, comprehensive GCxGC and sequential GC-GC for three selected challenging petrochemical applications. The fundamental theoretical aspects of the techniques are discussed. Oxygenates are removed as far as possible in C10 – C13 alkylation feedstocks, used in the production of linear alkyl benzenes, because the oxygenates may have deactivating effects on some expensive alkylation catalysts. Residual oxygenates may still be present and can consist of hundreds of components. Detection of individual components at ng/g levels is required. Heart-cut GC-GC is used to illustrate the separation and enrichment power for oxygenates in an alkylation feedstock. The stationary phase in the first dimension column was selected to provide separation of the oxygenates from the hydrocarbons in a relatively narrow window. The oxygenate fraction is then enriched by repeated injections and collection on the cryotrap. After sufficient enrichment, the trap is heated and the oxygenates are analysed on the second dimension column. Comprehensive GCxGC and Sequential GC-GC are compared for the separation and analysis of the oxygenated chemical component classes in the alkylation feedstock, before removal of oxygenates. Cyclic alcohols can occur in detergent alcohols produced from FT feedstocks. These cyclics are regarded as impurities because they affect the physical properties of the detergents. The cyclic and noncyclic alcohols in a narrow C12 – C13 detergent alcohol distillation cut have similar boiling points and polarities, and separation of individual components is thus difficult to achieve. Comprehensive GCxGC and sequential GC-GC are evaluated for the separation of the alcohol component classes. The study shows that both approaches provide component class separation but the high resolving power of the second column and the optimal chromatographic operating conditions of sequential GC-GC provide better separation of the individual components. The study illustrates the immense power of the three multidimensional GC techniques namely heart-cut GC-GC, comprehensive GCxGC and sequential GC-GC. The three multidimensional GC techniques each have their own advantages, disadvantages and unique applications and should be used as complementary rather than as competitive analytical tools. / AFRIKAANSE OPSOMMING: Fischer Tropsch (FT) petrochemiese produkte is van baie hoë kompleksiteit en kan uit duisende komponente bestaan. Chemikalië afkomstig van dié voerstrome bevat soms spoorhoeveelhede onsuiwerhede wat deaktiverend op kataliste kan inwerk of wat die werkverrrigting van finale produkte kan beïnvloed. Enkeldimensie GC analises van die komplekse mengsels is meesal onakkuraat as gevolg van geweldige piekoorvleueling. Die studie evalueer die skeidingsvermoë van drie multidimensionele tegnieke, Heart-cut GC-GC, Comprehensive GCxGC en Sequential GC-GC vir geselekteerde petrochemiese toepassings. Die fundamentele teoretiese aspekte van die tegnieke word bespreek en drie analitiese toepassings word beskryf. Oksigenate word so ver moontlik verwyder uit C10 – C13 paraffien-voerstrome, wat gebruik word in die vervaardiging van liniêre alkielbenzene, aangesien dit deaktiverend kan inwerk op alkileringskataliste. Die oorblywende oksigenate kan uit honderde komponente bestaan sodat analise van individuele komponente tot op lae ng/g vlakke nodig is. Heart-cut GC-GC word gebruik om die skeiding en verryking van die oksigenate in die alkileringsvoerstroom te illustreer. Die stationêre fase in die eerste-dimensie kolom is so gekies dat skeiding tussen oksigenate en koolwaterstowwe verkry word. Met herhaalde inspuitings verhoog die oksigenaat-konsentrasie op die cryo val en - na voldoende verryking - word die val verhit en die oksigenate geanaliseer op die tweede dimensie kolom. Die skeiding en analises verkry met Comprehensive GCxGC en Sequential GC-GC word vergelyk vir die chemiese klasse-skeiding van die alkileringsvoer (voor verwydering van oksigenate). Sikliese alkohole kan voorkom in detergent-alkohole vervaardig vanaf FT voerstrome. Dit word as onsuiwerhede beskou aangesien dit die fisiese eienskappe van die finale produkte beïnvloed. Die sikliese en nie-sikliese alkohole se kookpunte en polariteite is baie naby aanmekaar sodat skeiding van individuele komponente moeilik verkry word. Comprehensive GCxGC en Sequential GC-GC word evalueer vir die skeiding van die alkohol. Die studie toon aan dat albei die tegnieke skeiding gee van die chemiese komponent-klasse maar dat die hoë-resolusie tweede-dimensie kolom en die optimisering van die experimentele kondisies van die Sequential GC-GC sisteem beter skeiding van individuele komponente gee. Die uitsonderlike skeidingsvermoë van die drie multidimensionele tegnieke, Heart-cut GC-GC, Comprehensive GCxGC en Sequential GC-GC word geïllustreer in die studie. Elke tegniek het sy eie voordele, nadele en unieke toepassings en die drie tegnieke behoort as komplementêre eerder as kompeterende tegnieke gebruik te word.

Thesis (MA)--University of Stellenbosch, 2002. / ENGLISH ABSTRACT: This study explores patterns of separation and/or connection in the narratives of the respondent, a female farm worker living and working in the Western Cape, South Africa. The major objective of this qualitative case study is to examine the possible construction, co-existence and interaction of separation-connection themes in the reality of the respondent. Founded within the social constructivist tradition, an approach that assumes reality to be constructed through language and within relationships, a window on the respondent's narrative construction of her reality, relationships and separation-connection processes was obtained. To compliment the explorative nature and social constructionist approach of the study, Grounded Theory and Narrative Analysis were administrated. Through the analysis the two central themes, separation and connection, manifested on two different levels - firstly on a content level (what the participant has to say regarding the themes) and secondly on a process level (what is happening between participant and researcher). Findings provided a preliminary understanding of the techniques the respondent implores to construe a sense of separation and connection. Results confirmed the co-existence of separation-connection themes and indicated a possible interaction between the two constructs. Findings also provided a glimpse on the experiences and impact of the separation-connection process in the idiom of the respondent. / AFRIKAANSE OPSOMMING: Die studie belig patrone van binding en/of skeiding in die narratiewe van die respondent, In vroulike plaaswerker in die Wes-Kaap, Suid-Afrika. Dié kwalitatiewe gevallestudie is gerig op In ondersoek van die potensiële konstruksie, naasbestaan en interaksie van binding- en/of skeidingstemas soos wat die respondent dit beleef en verwoord. Deur die fundering van die navorsing in die sosiaal-konstruktivistiese tradisie, In benadering wat glo dat die realiteit in verhoudings via taal gekonstrueer word, is toegang tot die respondent se narratiewe konstruksie van haar realiteit, verhoudings en binding- en/of skeidingstemas verkry. In ooreenstemming met sosiaal-konstruktivistiese aannames, het die data-analise Narratiewe Analise en Grounded Theory metodiek behels. Met behulp van die ontleding het die twee sentrale konsepte, binding en skeiding, op twee vlakke gemanifesteer - eerstens op In inhoudsvlak (dit wat die respondent daaroor vertel) en tweedens op In prosesvlak (dit wat tussen die respondent en die onderhoudvoerder gebeur). Die resultate bied In voorlopige verstaan van die wyses waarop die respondent binding en/of skeiding konstrueer. Bevindings bevestig die naasbestaan van binding- en skeidingstemas en dui op In moontlike interaksie tussen dié twee konstrukte. Die studie verskaf ook In blik op die respondent se ervaring van die konstrukte in haar eie idioom.

Thesis (PhD)--Stellenbosch University, 2008. / ENGLISH ABSTRACT: Radiochemical research involving ion exchange chromatography is of paramount importance to the future of radionuclide production at the Radionuclide Production Group (RPG) of iThemba LABS. It is required for the production of high-activity yields of radionuclides to effectively remove impurities and for the safety of the operators performing such productions. The radiochemical separations of some new products from their target material, as well as experiments to determine whether production is viable, are described. 67Ga is currently being produced at the RPG and makes use of zinc targets. With the production of ultra-pure 67Ga, it was necessary to remove any Fe(III) impurities from the final product, such that it may be possible to label peptides with this product. The use of Amberchrom CG161M for this purpose was found to be satisfactory. Interest was shown in 88Y by an overseas company for the manufacture of sources. While a method involving extraction of the radionuclide and the ion exchange thereof using Chelex 100 chelating resin had been published, problems with the production persisted. Three methods, using ion exchange chromatography, were devised to produce the radionuclide, with two of them being adopted for production purposes. Thick-target nuclear data have also recently been accumulated in collaboration with colleagues from ATOMKI, Debrecen, Hungary. There is a large demand for 82Sr for the manufacture of 82Sr/82Rb generators for medical use. A method was developed to manufacture this radionuclide with thicker (32 g) target material, bombarded in the Vertical Beam Target Station (VBTS), and to separate 82Sr from its target material with the use of Purolite S950 chelating resin. 68Ge/68Ga generators are becoming increasingly important in the world of radiopharmaceuticals. A project to develop a local generator was funded by the Innovation Fund and research was performed to produce 68Ge, such that the generator could be manufactured. This involved bombarding thicker Ga targets in the VBTS and performing the chemical separation using AG MP-1 anion exchange resin. The final product was loaded onto generators, although tests performed on different materials to the ones being marketed are also reported in this work. A project was initiated to study the cluster radioactive decay of 223Ac via 14C and 15N emission. To produce 223Ac for these observations, a Th target was bombarded. The 227Pa was separated from the target material using AG MP-1 macroporous anion exchange resin and used as a source, which decayed to 223Ac. The chemical separation and the drying of the final product onto a source plate were completed within approximately 70 minutes from the end of bombardment. The work was performed in collaboration with JINR, Russia, and University of Milan and INFN, Italy. 133Ba has a half-life of over 10 years and is an expensive radionuclide to produce. It has been used in medical and biological studies and there still appears to be a demand for it. A method was devised, utilizing AG50W-X4 cation exchange resin, to separate 133Ba from its CsCl target material. Agricultural specialists in the past have shown an interest in 28Mg, to determine the uptake of the element in fruit. It has long been regarded by some of the local researchers as an interesting project to investigate. It has been determined that the product can be produced in reasonable quantities using LiCl target material, with ten targets being bombarded in series using a 200 MeV proton beam delivered by the Separated Sector Cyclotron. A method, involving the use of Purolite S950 chelating resin, was devised to separate 28Mg from its target material. / AFRIKAANSE OPSOMMING: Radiochemiese navorsing, wat ioonuitruiling chromatografie behels, is van uiterste belang vir die toekoms van die produksie van radionukliede by die Radionukliedproduksiegroep (RPG) van iThemba LABS. Dit is nodig vir die hoë aktiwiteit opbrengs van radionuklied produkte om onsuiwerhede te verwyder en vir die veiligheid van die operateurs wat die produksies moet uitvoer. Die skeiding van nuwe produkte van hulle skyfmateriaal, sowel as eksperimente om vas te stel of ‘n produksie uitvoerbaar is, word in die werk beskryf. 67Ga word tans by RPG vervaardig en maak gebruik van sink as skyfmateriaal. Vir die produksie van “ultra-suiwer” 67Ga was dit belangrik om enige Fe(III) onsuiwerhede uit die finale produk te verwyder om sodoende peptiede merking te kan uitvoer. Die gebruik van Amberchrom CG161M hars was voldoende vir dié eksperiment. ‘n Oorsese maatskappy het belangstelling getoon in 88Y vir die vervaardiging van bronne. Alhoewel ‘n metode wat die ekstraksie van die radionuklied en die ioonuitruiling daarvan met die gebruik van Chelex 100 chelerende hars reeds gepubliseer was, het probleme met die produksie voortgeduur. Drie metodes is opgestel om 88Y te produseer, waarvan twee van die metodes tans gebruik word vir produksie doeleindes. Dik-skyf kerndata is ook versamel in samewerking met kollegas van ATOMKI, Debrecen, Hongarye. Daar is ‘n groot aanvraag vir 82Sr vir die vervaardiging van 82Sr/82Rb generators vir mediese doeleindes. ‘n Metode is ontwikkel om die radionuklied te vervaardig van dikker skyfmateriaal (32 g), in die Vertikale Bundelstasie gebombardeer, en om 82Sr van sy skyfmateriaal te skei met die gebruik van Purolite S950 chelerende hars. 68Ge/68Ga generators is besig om toenemend belangrik te word in die wêreld van radiofarmasie. iThemba LABS kry baie navrae om die produk te vervaardig. Die projek was ook deel van die voorlegging aan die “Innovation Fund” en ‘n manier is ondersoek om 68Ge te vervaardig, wat benodig word om so ‘n generator te laai. Dik Ga skyfmateriaal word in die Vertikale Bundelstasie gebombardeer en ‘n chemiese skeiding is uitgevoer deur gebruik te maak van AG MP-1 anioonuitruiling hars. Die finale produk is op die generators gelaai vir toetsdoeleindes. Toetse is ook op ‘n ander tipe generator uitgevoer en word in die werk beskryf. ‘n Projek is begin om “cluster” radioaktiewe verval van 223Ac, via 14C en 15N emissie, te bestudeer. ‘n Th-skyf is met protone gebombardeer om die 223Ac te produseer vir die eksperiment. 227Pa is vervaardig en geskei van die skyfmateriaal. Dit is gedoen met die gebruik van AG MP-1 makroporeuse anioonuitruiling hars en drooggemaak op ‘n bronplaat, waar dit verval het na 223Ac. Die chemiese skeiding en die droogmaak van die finale produk op ‘n bronplaat is uitgevoer binne 70 minute na Einde van Bombardering (EVB). Die werk is deel van ‘n samewerking met kollegas van JINR, Rusland, en die Universiteit van Milaan, sowel as INFN, Italië. 133Ba het ‘n halveertyd van oor die tien jaar en is ‘n duur produk om te vervaardig. Dit is al gebruik in mediese en biologiese studies en daar is deesdae ‘n redelike aanvraag daarvoor. ‘n Metode is uitgewerk om 133Ba te skei van die CsCl skyfmateriaal met die gebruik van AG50W-X4 katioonuitruiling hars. Spesialiste in landboustudies het in die verlede belangstelling getoon in 28Mg. Dit word gebruik om die absorpsie van dié element in vrugte te ondersoek. Die produk kan vervaardig word met die gebruik van LiCl skyfmateriaal: tot soveel as tien skywe (agter mekaar) word gebombardeer met ‘n 200 MeV protonbundel te iThemba LABS. ‘n Metode, wat Purolite S950 behels, is daargestel om 28Mg van die skyfmateriaal te skei.

Thesis (PhD)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: Complex polymer systems have multiple distributions with regard to molecular parameters such as molar mass, functionality, chemical composition, molecular architecture and microstructure. These distributions affect the properties of the polymers making it necessary to develop separation methods to be able to correlate structure to property. A single onedimensional chromatographic method is usually not sufficient to separate these complex polymers with respect to all the distributions. Hence, multidimensional liquid chromatography is necessary for the complete analysis of complex polymers using two or more chromatographic techniques before detection. In this work, two novel liquid chromatographic methods were developed to separate complex polymers according to microstructure. Comprehensive two-dimensional liquid chromatography (LC x LC) was carried out to observe the correlation between microstructure and molar mass. The separation according to microstructure was coupled to NMR (LC-NMR) to observe, identify and quantify the different microstructural components during chromatographic elution. The first chromatographic method separated hydrogenated and deuterated polystyrene homopolymers with respect to the isotope effect. For the LC x LC experiments, liquid chromatography at critical conditions (LCCC) was employed as the first dimension separating according to the isotope effect and size exclusion chromatography (SEC) as the second dimension separating according to molar mass. The LC x LC results of the blends showed that there was an improvement in isotopic separation with an increase in molar mass. The LCNMR coupling using both 1H and 2H NMR detection allowed for the identification of low molar mass blend components which were not sufficiently separated by liquid chromatography. The second chromatographic method separated stereoregular poly(methyl methacrylate)s (PMMAs) with respect to tacticity. The LC x LC experiments of stereoregular PMMAs utilised solvent gradient liquid chromatography as the first dimension to separate according to tacticity and size exclusion chromatography (SEC) as the second dimension to separate according to molar mass. The LC x LC results showed a change in the triad composition with elution of the stereoregular PMMAs with a slight influence of molar mass. The LC-NMR coupling allowed the observation of the triad composition during chromatographic elution. / AFRIKAANSE OPSOMMING: Komplekse polimeriese sisteme het meervoudige verspreidings ten opsigte van molekulêre parameters, soos byvoorbeeld, molêre massa, funksionaliteit, chemiese samestelling, molekulêre argitektuur en mikrostruktuur. Hierdie verspreidings beïnvloed die eienskappe van die polimere en dus is dit nodig om skeidingsmetodes te ontwikkel ten einde polimeerstruktuur met polimeereienskappe te kan korreleer. ‘n Enkele een-dimensionele chromatografiese metode is gewoonlik nie voldoende om hierdie komplekse polimere te skei met betrekking tot al die verspreidings nie. Multidimensionele vloeistofchromatografie, met die insluiting van twee of meer chromatografiese tegnieke, is dus nodig om polimere te skei voor waarneming kan plaasvind. Twee nuwe chromatografiese metodes is ontwikkel om komplekse polimere volgens mikrostruktuur te skei. Twee-dimensionele vloeistofchromatografie (LC x LC) is uitgevoer ten einde die korrelasie tussen mikrostruktuur en molêre massa te ondersoek. Daarna is die skeiding wat op mikrostruktuur gebasseer is, gekoppel aan KMR (LC-KMR) om die verskillende mikrostrukturele komponente gedurende chromatografiese eluering waar te neem, te identifiseer en te kwantifiseer. Die eerste chromatografiese metode het die gehidrogeneerde en gedeutereerde polistireen geskei met betrekking tot die isotoopeffek. Hier het die LC x LC skeiding bestaan uit vloeistofchromatografie onder kritiese kondisies (LCCC) as die eerste dimensie, wat skeiding bewerkstellig het gebasseer op die isotoopeffek, en grootte-uitsluitingschromatografie (SEC) as die tweede dimensie, wat skeiding bewerkstellig het gebasseer op die molêre massa. Die LC x LC resultate van die vermengings het ‘n verbetering in isotopiese skeiding met ‘n toename in molêre massa getoon. Deur gebruik te maak van die LC-KMR koppeling, waar beide 1H en 2H KMR waarneming gebruik is, was dit moontlik om die lae-molêre-massakomponente van vermengings wat nie volledig d.m.v. LC geskei kon word nie, te identifiseer. Die tweede chromatografiese metode het stereoreëlmatige polimetielmetakrilate (PMMAs) m.b.t. taktisiteit geskei. Die LC x LC skeiding van stereoreëlmatige PMMAs het bestaan uit oplosmiddel -gradiënt-LC as eerste dimensie om volgens taktisiteit te skei, en SEC as tweede dimensie om volgens molêre massa te skei. Die LC x LC resultate het ‘n molêre massa afhanklikheid van stereoreëlmatige PMMAs op taktisiteit getoon. Die LC-KMR koppeling het dit moontlik gemaak om die triade-samestelling gedurende chromatografiese eluering waar te neem.

Thesis (MSc)--Stellenbosch University, 2000. / ENGLISH ABSTRACT: The phenolic content of wine is responsible for determining characteristics such as the organoleptic qualities, colour stability, ageing properties and health-beneficial effects associated with wine. The aim ofthis study was to investigate the possibilities offered by capillary electrophoresis (CE) as an alternative separation technique to high performance liquid chromatography (HPLC) for the analysis of polyphenols in wine. The complexity of wine samples was the cause that neither technique was capable of a satisfactory singlestep analysis of wine. Suitable sample preparation techniques such as Sephadex- and Sep- Pak fractionation and ether extraction of wine polyphenols were investigated. These techniques did not, however, prove to be universal. A novel form of sample preparation namely a process analogous to lyophylization used to separate wine volatiles from nonvolatiles was introduced. The versatility of CE was further investigated in an attempt to eliminate the need for sample preparation. The use of polyvinylalcohol (PVA) coated capillaries, micellar electrokinetic chromatography (MEKC) and capillary gel electrophoresis (CGE) were investigated in this regard. Although none of these techniques could offer conclusive results, useful applications were forthcoming and routes for further investigation were outlined. Liquid chromatography coupled to electro spray ionisation mass spectroscopy (LC-ESI-MS) and capillary electrophoresis coupled to electro spray ionisation mass spectroscopy (CE-ESI-MS) were compared for the analysis of polyphenols in wine. While the latter technique could not produce sufficient separation compared to the former, future development ofCE-ESI-MS should make it a powerful technique for these analyses. / AFRIKAANSE OPSOMMING: Die fenoliese komponente in wyn speel 'n bepalende rol by eienskappe soos die organoleptiese karakter, kleur stabiliteit, verouderingspotensiaal en gesondheids-voordele wat met wyn geassosieër word. Die doel van hierdie projek was om ondersoek in te stel na die potensiaal wat kapillêre elektroforese (CE, "capillary electrophoresis") as 'n alternatiewe skeidingstegniek teenoor hoë druk vloeistof chromatografie (HDVC) vir die analise van die polifenole in wyn bied. Die kompleksiteit van wyn monsters is van so 'n aard dat 'n bevredigend enkelstap analise met geeneen van die tegnieke moontlik is nie. Gepaste monster-voorbereidingstappe soos Sephadex- en Sep-Pak fraksionering asook eter ekstraksie van die polifenole in wyn is ondersoek. Geeneen van die tegnieke was egter universeel toepaslik nie. 'n Nuwe metode van monster-voorbereiding, naamlik 'n proses analoog aan liofilisasie wat gebruik word om die wyn te skei in vlugtige en nievlugtige komponente is gedemonstreer. Die veelsydigheid van CE was gevolglik ondersoek in 'n poging om monstervoorbereiding uit te skakel. Die gebruik van polyvinielalkohol-(pVA) bedekte kapillêre, missellêre elektrokinetiese chromatografie (MEKC) en kapillêre gel elektroforese (CGE, "capillary gel electrophoresis) is in hierdie verband ondersoek. Alhoewel geeneen van hierdie tegnieke onweerlegbare resultate gelewer het nie, het bruikbare toepassings hieruit voortgespruit en is die grondslag vir verdere navorsing gelê. Vloeistof chromatografie gekoppel aan eIektrosproei ionisasie massaspektroskopie (LCESI- MS) en kapillêre elektroforese gekoppel aan elektrosproei ionisasie massaspektroskopie (CE-ESI-MS) is vergelyk vir die analise van polifenole in wyn. Alhoewel laasgenoemde tegniek onvoldoende skeiding lewer vergeleke met eersgenoemde, behoort toekomstige ontwikkelinge op die gebied van CE-ESI-MS dit 'n kragtige tegniek vir die analise van hierdie monsters te maak.

Thesis (MSc)--Stellenbosch University, 2014. / ENGLISH ABSTRACT: See item for full text / AFRIKAANSE OPSOMMING: Sien item vir volteks