Spelling suggestions: "subject:"simplified method"" "subject:"implified method""
1 |
The Effect of Bonded Reinforcing Steel on Increase in Stress in Unbonded Prestressing Steel at Ultimate StateWei, Sisi 19 March 2013 (has links)
To investigate the benefit induced by adding a small amount of bonded reinforcing steel into a fully unbonded prestressed concrete beam, two well-founded and straightforward approaches for predicting tendon stress are proposed. The primary approach utilizes a flexural analysis to calculate member deformation. The supplementary approach employs a truss model to consider the additional member deformation due to shear force. Both approaches use a simplified iterative method.
With these two approaches, a systematic parametric study is conducted to investigate the effects of various factors. The results indicate that adding little bonded reinforcement does significantly increase the stress increment in unbonded tendons at ultimate state for one-point loading as expected. Moreover, a lower span-to-depth ratio, the use of high-strength concrete, and a smaller mechanical reinforcement ratio also raise the stress increment.
|
2 |
The Effect of Bonded Reinforcing Steel on Increase in Stress in Unbonded Prestressing Steel at Ultimate StateWei, Sisi 19 March 2013 (has links)
To investigate the benefit induced by adding a small amount of bonded reinforcing steel into a fully unbonded prestressed concrete beam, two well-founded and straightforward approaches for predicting tendon stress are proposed. The primary approach utilizes a flexural analysis to calculate member deformation. The supplementary approach employs a truss model to consider the additional member deformation due to shear force. Both approaches use a simplified iterative method.
With these two approaches, a systematic parametric study is conducted to investigate the effects of various factors. The results indicate that adding little bonded reinforcement does significantly increase the stress increment in unbonded tendons at ultimate state for one-point loading as expected. Moreover, a lower span-to-depth ratio, the use of high-strength concrete, and a smaller mechanical reinforcement ratio also raise the stress increment.
|
3 |
Análise numérica de pilares de aço isolados e inseridos em paredes em situação de incêndio / Numerical analysis of isolated and embedded on walls steel columns under fire situationSimões, Yagho de Souza 10 April 2018 (has links)
Em um incêndio, pilares de aço inseridos em paredes apresentam uma resposta termoestrutural diferente daqueles isolados, de modo que a compartimentação oferece um aumento de sua resistência ao fogo. Poucos estudos foram desenvolvidos até o presente momento para avaliar o desempenho de pilares em contato com paredes, sendo que aqueles já realizados apresentaram respostas que ainda deixam dúvidas sobre esses elementos. Diante disso, este trabalho propõe analisar, em contexto numérico, o comportamento de pilares de aço isolados e inseridos em paredes sujeitos à ação térmica, a partir do uso do código computacional ABAQUS versão 6.14. A modelagem termoestrutural, considerando a parede somente como elemento de compartimentação, promoveu resultados pouco consistentes, o que leva a concluir que a alvenaria influencia na resposta estrutural de pilares em situação de incêndio. Por essa razão, ao inserir molas que controlam o deslocamento axial das paredes na modelagem numérica, os resultados alcançados passaram a ser mais representativos. Análises complementares a respeito da influência do fator de carga e do nível de rigidez axial e rotacional na resistência ao fogo dos pilares também foram realizadas. Para todos os modelos, constatou-se a influência negativa do fator de carga quando aumentado. Quanto à restrição axial, foi verificado que sua presença possui maior influência na resistência ao fogo em comparação com sua intensidade, uma vez que a elevação desse parâmetro não afetou o tempo crítico dos pilares, para a maior parte dos casos analisados. Em relação à rigidez rotacional, ela se mostrou favorável para a resistência ao fogo. Além do mais, a pesquisa contou com uma avaliação do método simplificado da ABNT NBR 14323:2013 para cálculo da evolução da temperatura em perfis de aço. Concluiu-se que ele apresenta melhores resultados para os pilares com aquecimento uniforme na seção transversal. Por essa razão, foi proposta uma nova metodologia de cálculo de temperatura para pilares em contato com paredes, validada por meio de testes numéricos. / In a fire situation, steel columns embedded on walls demonstrate a different thermo- structural response from those isolated, so that the subdivision offers an increase of its fire resistance. Few studies have been developed in order to evaluate the performance of columns in contact with walls, and those already performed showed results that still leave doubts about these elements. Therefore, this work proposes to analyze, in a numerical context, the behavior of isolated and embedded on walls steel columns in fire using the software ABAQUS 6.14 as a modeling tool. The thermo-structural modeling, considering the wall only as a compartmentation element, has presented poor results, which leads to the conclusion that the masonry has influence on the structural response of columns subjected to fire situation. For this reason, when inserting springs in order to control the axial displacement of the walls in numerical modeling, the obtained results were satisfactory. Further analyzes in respect of the load factor influence and the level of axial and rotational stiffness on the fire resistance of columns were also performed. For all the models, it was verified a negative influence of the load factor when increased. However, when it comes to the axial restriction, it was verified that its presence had more influence in the fire resistance of the structural element despite of its intensity, once the increase of this parameter did not affect the critical time of the columns, for most cases analyzed. In respect to rotational stiffness, it was proven favorable to the fire resistance. In addition, this research employed the simplified method presented in the ABNT NBR 14323: 2013 to calculate the temperature evolution in steel profiles. It was concluded that it presents good results only for the columns with uniform heating in the cross section. For this reason, a new methodology to calculate the temperature of columns in contact with wall was proposed, validated by numerical tests.
|
4 |
Stabilité des digues sous chargement sismique : vers une nouvelle génération de méthodes simplifiées / Stability of embankments under seismic loading : towards a new generation of simplified methodsDurand, Capucine 12 July 2018 (has links)
Permettant de protéger les populations des inondations, de canaliser l'eau à des fins d'irrigation ou de production d'électricité, les digues en terre sont des ouvrages stratégiques dont la rupture peut avoir des conséquences dramatiques. La stabilité de ces ouvrages doit ainsi pouvoir être assurée, notamment en cas de séisme. Cependant, étant donné le très grand linéaire qu'ils représentent, la mise en œuvre de vastes campagnes de reconnaissances et de modèles numériques complexes n'est pas toujours envisageable dans les zones de sismicité modérée. L'utilisation d'outils simplifiés, faisant appel à des données facilement mesurables, se révèle indispensable pour fournir une indication sur la stabilité de tronçons de digue soumis à un chargement sismique. Les méthodes simplifiées existantes permettant d'estimer la réponse dynamique des remblais sont inadaptées au contexte des digues. En effet, alors que les digues sont pour la plupart construites dans des vallées sédimentaires, la majorité de ces méthodes, développées pour l’étude des barrages, supposent que l’ouvrage est fondé directement au rocher. Seules deux approches permettent de prendre en compte l’interaction entre l’ouvrage et son sol d’assise (effets de site) : la méthode de Sarma(1979) et celle de Papadimitriou(2014). Cependant, la première est basée sur des hypothèses très fortes (elle considère notamment un rocher rigide et un amortissement uniforme, qui plus est très fort) et la seconde se limite à des ouvrages ayant une hauteur supérieure à 20 si{m}. L'approche développée au cours de cette thèse repose sur des hypothèses plus réalistes, en considérant notamment des géométries adaptées à celles des digues, en prenant en compte les effets de site et en adaptant la dissipation d'énergie au niveau de sollicitation. Une étude paramétrique numérique (calcul de la réponse visco-élastique par éléments spectraux en deux dimensions) est utilisée pour couvrir un ensemble de configurations géométriques et mécaniques de digues. Pour prendre en compte la non-linéarité, les valeurs d'amortissement et de dégradation du module de cisaillement sont adaptées en chaque point des modèles à partir des résultats fournis par une série de calculs en linéaire équivalent 1D. Les réseaux de neurones artificiels, dont l'apprentissage est basé sur les résultats des simulations numériques, sont utilisés pour le développement d'une nouvelle méthode simplifiée. Des abaques sont réalisés, à partir des réseaux de neurones établis, pour offrir une alternative visuelle à leur utilisation "mathématiques". Les outils simplifiés auxquels aboutit cette thèse font appel à des paramètres facilement mesurables sur le terrain. Des méthodes géophysiques sont mises en œuvre au niveau de quatre sites de digues afin d'identifier le meilleur compromis de mesures permettant d'estimer les paramètres nécessaires à l'évaluation de la réponse dynamique de l'ouvrage. / Embankments are strategic facilities that, among other things, protect population from flooding and canalize rivers for energy production or for irrigation concerns. Since their rupture can lead to terrible consequences, they must remain stable, especially in case of earthquake. However, given the very large length of embankments, it is rarely possible to conduct complete investigations and complex numerical models in regions of moderate seismicity. Therefore, simplified tools to estimate the dynamic response of embankments using accessible embankments’ features are necessary to estimate their capacity to resist seismic loadings. Existing simplified methods, generally developed to assess the dynamic response of embankment-dams, turn out to be inappropriate to study the particular case of embankments along rivers – or other types of embankment, with small height and large length. The majority of these simplified methods do not take into account site effects: they assume the presence of rock directly at the base of the embankment, whereas most of large length embankments are located in alluvial valleys. Two methods only - Sarma(1979) and Papadimitriou(2014) - take into account the interaction between the embankment and its soil foundation. However, the first one relies on strong assumptions (among others, that the bedrock is considered rigid and that the viscous damping is supposed to be both spatially uniform and very large) and the second one is limited to tall embankments (higher than 20 si{m}).The method developed in this thesis relies on assumptions that are more realistic: it considers geometries adapted to large length embankments, it accounts for the presence of a soil foundation and includes an energy dissipation process consistent with expected levels of strain. A numerical parametric study is performed based on the computation with the spectral element method of the viscoelastic response of a large set of embankments spanning a wide range of geometrical and mechanical properties. In order to take into account nonlinearity, damping and shear modulus reduction are adapted in each point of the numerical models according to the results of a set of 1D linear equivalent computations. A new simplified method is derived from the obtained numerical results using artificial neural networks. Abacuses are produced from the neural networks so that engineers can have at their disposal a visual tool. This thesis leads to a simplified method that uses some accessible features of embankments as input parameters. The ability of classical geophysical methods to provide those input parameters is further estimated on four sites corresponding to different realistic configurations.
|
5 |
Análise numérica de pilares de aço isolados e inseridos em paredes em situação de incêndio / Numerical analysis of isolated and embedded on walls steel columns under fire situationYagho de Souza Simões 10 April 2018 (has links)
Em um incêndio, pilares de aço inseridos em paredes apresentam uma resposta termoestrutural diferente daqueles isolados, de modo que a compartimentação oferece um aumento de sua resistência ao fogo. Poucos estudos foram desenvolvidos até o presente momento para avaliar o desempenho de pilares em contato com paredes, sendo que aqueles já realizados apresentaram respostas que ainda deixam dúvidas sobre esses elementos. Diante disso, este trabalho propõe analisar, em contexto numérico, o comportamento de pilares de aço isolados e inseridos em paredes sujeitos à ação térmica, a partir do uso do código computacional ABAQUS versão 6.14. A modelagem termoestrutural, considerando a parede somente como elemento de compartimentação, promoveu resultados pouco consistentes, o que leva a concluir que a alvenaria influencia na resposta estrutural de pilares em situação de incêndio. Por essa razão, ao inserir molas que controlam o deslocamento axial das paredes na modelagem numérica, os resultados alcançados passaram a ser mais representativos. Análises complementares a respeito da influência do fator de carga e do nível de rigidez axial e rotacional na resistência ao fogo dos pilares também foram realizadas. Para todos os modelos, constatou-se a influência negativa do fator de carga quando aumentado. Quanto à restrição axial, foi verificado que sua presença possui maior influência na resistência ao fogo em comparação com sua intensidade, uma vez que a elevação desse parâmetro não afetou o tempo crítico dos pilares, para a maior parte dos casos analisados. Em relação à rigidez rotacional, ela se mostrou favorável para a resistência ao fogo. Além do mais, a pesquisa contou com uma avaliação do método simplificado da ABNT NBR 14323:2013 para cálculo da evolução da temperatura em perfis de aço. Concluiu-se que ele apresenta melhores resultados para os pilares com aquecimento uniforme na seção transversal. Por essa razão, foi proposta uma nova metodologia de cálculo de temperatura para pilares em contato com paredes, validada por meio de testes numéricos. / In a fire situation, steel columns embedded on walls demonstrate a different thermo- structural response from those isolated, so that the subdivision offers an increase of its fire resistance. Few studies have been developed in order to evaluate the performance of columns in contact with walls, and those already performed showed results that still leave doubts about these elements. Therefore, this work proposes to analyze, in a numerical context, the behavior of isolated and embedded on walls steel columns in fire using the software ABAQUS 6.14 as a modeling tool. The thermo-structural modeling, considering the wall only as a compartmentation element, has presented poor results, which leads to the conclusion that the masonry has influence on the structural response of columns subjected to fire situation. For this reason, when inserting springs in order to control the axial displacement of the walls in numerical modeling, the obtained results were satisfactory. Further analyzes in respect of the load factor influence and the level of axial and rotational stiffness on the fire resistance of columns were also performed. For all the models, it was verified a negative influence of the load factor when increased. However, when it comes to the axial restriction, it was verified that its presence had more influence in the fire resistance of the structural element despite of its intensity, once the increase of this parameter did not affect the critical time of the columns, for most cases analyzed. In respect to rotational stiffness, it was proven favorable to the fire resistance. In addition, this research employed the simplified method presented in the ABNT NBR 14323: 2013 to calculate the temperature evolution in steel profiles. It was concluded that it presents good results only for the columns with uniform heating in the cross section. For this reason, a new methodology to calculate the temperature of columns in contact with wall was proposed, validated by numerical tests.
|
6 |
Vertical-flow constructed wetlands for the treatment of wastewater and stormwater from combined sewer systemsArias Lopez, José Luis 30 September 2013 (has links) (PDF)
French vertical-flow constructed wetlands (VFCW) directly treating raw wastewater are known to perform well on for SS, COD and nitrification. They are also known to robustly cope with hydraulic overloads during rainfall events. Although numerous systems have been installed in areas equipped with a combined sewer, the limits of stormwater acceptance remain ill-defined and need to be improved. Looking at the various VFCW designs and usages reported in the literature, it is difficult to draw any consensus on their hydraulic limits. Consequently, designing VFCW to accept hydraulic overloads is a complex task, as local context strongly impacts inlet flows produced during rainfall events. Dynamic models appear a requisite for filter design in such cases. Numerical CW models have essentially focused on horizontal flow, with few attempting to study VFCW dynamics which are more commonly tackled via mechanistic models. Although mechanistic models are powerful tools for describing processes within the VFCW, they are generally too complicated to be readily used by designers. The choice between detailed description and easy handling will depend on the modelling aims. If the aim is a global design tool, simplified models offer a good alternative. However, the simplified models geared to studying VFCW dynamics are extremely reduced. They are easy-handling for design and well-adapted to specific purposes (combined sewer overflow -CSO- treatment) but not necessarily to VFCW treating combined sewer wastewater, where long-term infiltration rates vary significantly. Consequently, this PhD thesis work focused on developing a simplified hydraulic model of VFCW to guide designers through the process of adapting VFCW systems to treat domestic wastewater in both dry and rain events. The simplified model makes it possible to link (i) hydraulics, by simulation of ponding time variations, (ii) biological performances, by establishing "dysfunction alerts" based on treatment performance assessment and variations in online N forms effluent from the young VFCW. These "dysfunction alerts" plot the maximal hydraulic load that a filter can accept without compromising its biological activity. The simplified model was used to model long-term hydraulics in the VFCW (i) to analyze the impact of local context and filter design on hydraulic overload acceptance (using "dysfunction alerts" and bypass discharges) and (ii) to propose VFCW designs for accepting hydraulic overload in different contexts. The modelling demonstrates that VFCW can limit days with bypass discharges to less than 20 times per year without jeopardizing filter performances. Moreover, the most problematic scenario on stormwater treatment remains a watershed with high imperviousness coefficient and low slope under a Bretagne-type climate, demonstrating that the filter is more sensitive to periodicity and duration than to intensity of rainfall events.
|
7 |
Prise en compte des contraintes résiduelles dans le dimensionnement en fatigue oligocyclique par des méthodes simplifiées / Taking residual stresses into account using simplified methods in low cycle fatigueLevieil, Bruno 03 November 2016 (has links)
Les contraintes résiduelles, introduites lors de la fabrication des pièces mécaniques, influent sur leur durée de vie en fatigue et doivent donc être prises en compte. Ce travail vise à développer une méthode de dimensionnement rapide en fatigue oligocyclique permettant leur prise en compte, aussi bien sous chargement de traction que de compression. L’idée principale est de calculer analytiquement le cycle stabilisé uniquement au point critique de la structure à l’aide d’une méthode simplifiée en plasticité confinée. Cette dernière est basée sur une loi de localisation, qui étend les méthodes énergétiques de type Neuber au cas général multiaxial. La loi de localisation permet de relier le chargement appliqué à la structure à celui observé localement au point critique. Elle est calibrée à l’aide d’une simulation éléments finis sous chargement monotone de la structure. Pour cela, le comportement élasto-plastique du matériau est d’abord caractérisé à partir d’un essai de traction avec charges-décharges. A l’aide de ce seul essai, la loi de comportement est identifiée de manière séquentielle, en utilisant des écrouissages cinématique et isotrope à seuil. Ce seuil permet d’améliorer la prévision de la contrainte moyenne stabilisée, utilisée dans le critère de fatigue proposé. Ce dernier a été identifié sur des essais purement alterné (Rε=-1), puis validé pour des chargements de traction alternée (Rε>-1) et de compression alternée (Rε<-1). L’application de la démarche en plasticité confinée est réalisée sur des éprouvettes à double encoche présentant initialement différents états de contraintes résiduelles. L’évolution des contraintes locales sous chargement cyclique nominal de traction répétée (Rσ=0) ou de compression répétée (Rσ=-∞) est mesurée. Cette évolution est ensuite comparée aux prévisions numériques et analytiques obtenues à l’aide de la loi de comportement et de la méthode simplifiée. L’application du critère de fatigue aux données stabilisées prévues par les modèles a permis d’obtenir des durées de vie avec un conservatisme indépendant du rapport de charge et de l’état initial. Enfin, une application de la démarche complète sur des joints soudés en T est réalisée afin d’élargir le spectre d’application de la méthode. / Residual stresses are inherent to the manufacturing processes and can have a strong effect on the fatigue life of structures. Therefore, they shall be taken into account in fatigue design. In this PhD thesis, a fast design method is developed to take residual stresses into account in low cycle fatigue, either under tensile or compressive loadings. The main idea is to calculate analytically the stabilised stress-strain curve, at the critical point, by using a simplified method for confined plasticity. This method is based on a localisation law that extends energetic methods like Neuber to general multiaxial stress states. The localization law links the applied load to the local load at the critical point. It has to be identified on a finite element analysis of the structure under monotonic load. For this purpose, the elasto-plastic behaviour of the material is characterised from one single tensile test with loadings-unloadings. The behaviour law, identified sequentially, includes isotropic and kinematic hardenings with thresholds. This improves the stabilised mean stress prediction, which is used in the proposed fatigue criterion to represent the influence of the load ratio on the fatigue life. This criterion is identified on purely alternated tests (Rε=-1), and then validated under various tensile load ratios (Rε>-1) as well as compressive load ratios (Rε<-1). The methodology is validated on plate specimens with two semi-circular notches, which initially present different residual stresses states. The experimental evolution of local stresses during cyclic compressive (Rσ=-∞) and tensile (Rσ=0) repeated applied loads have been studied experimentally and compared to the numerical and analytical predictions. The same work has been achieved on the fatigue lives predictions. It shows that a slight conservatism, independent from the load ratio and the initial state, is obtained. Finally, an application of the method on T-Joints is realised to enlarge the scope of the method.
|
8 |
A Comperative Assessment Of Available Methods For Seismic Performance Evaluation Of Buried StructuresOzcebe, Ali Guney 01 August 2009 (has links) (PDF)
In the last three decades, seismic performance assessment of buried structures has evolved through the following stages : i) buried structures are not prone to seismically-induced damages, thus no need for detailed investigations, ii) eliminating soil-structure-earthquake interaction and use of seismically-induced free field ground deformations directly as the basis for seismic demand, thus producing conservative results, and finally iii) soil-structure and earthquake interaction models incorporating both kinematic and inertial interactions. As part of soil-structure and earthquake interacting models, simplified frame analysis established the state of practice and is widely used. Within the confines of this thesis, the results of simplified frame analysis based response of buried structures are compared with those of 2-D finite element dynamic analyses. For the purpose, 1-D dynamic and 2-D pseudo-dynamic analyses of free field and buried structural systems are performed for a number of generic soil, structure and earthquake combinations. The analyses results revealed that, in general, available closed form solutions are in pretty good agreement with the results of finite element analyses. However, due to the fact that dynamic analyses can model both kinematic and inertial effects / it should be preffered for the design of critical structures.
|
9 |
Porovnání cen ovocných dřevin zjištěných zjednodušeným a výnosovým způsobem / Comparison of Fruit Trees Prices Ascertained by the Simplified and Yield MethodJašová, Alena January 2012 (has links)
The Thesis „Comparison of fruit trees prices ascertained by the simplified and yield method“ deals with the comparison of both pricing methods, where there are defined factors on the basis of ascertained facts which have essential influence on price difference of fruit trees and subsequently the proposal to their modification is made.
|
10 |
Porovnání cen venkovních úprav na pozemku ve funkčním celku s rodinným domem stanovených nákladovým a zjednodušeným způsobem ve vybrané lokalitě v Brně / Comparison of Prices for External Works on a Land Parcel in a Functional Unit with a Family House Determined via the Cost Method and in a Simplified Manner at a Chosen Location in BrnoŘíha, Milan January 2012 (has links)
The aim of the thesis is to assess the influence of the exterior finish works on the total price of a house. The total price of the house consists of the interior price valuated by the cost method and the price of the exterior finishes which were valuated with the help of two methods: the cost method and the simplified method based on the Property Valuation Act. The valuation also covers several periods of time: a new building and 11-, 25-, 50-, 75- and 100-years-old buildings. The thesis focuses on the lifetime of individual parts of the exterior finishes—especially the time after which it is necessary to replace or reconstruct a part. A significant focus was placed on the percents listed in the Act and their correspondence to the actual state. The thesis also deals with the various methods of valuation and their appropriateness in each case. It also mentions the influence of other factors on the price of an estate (the use of different exterior finishes, or a selection of a building location) but these factors were not examined in detail.
|
Page generated in 0.0642 seconds