Bead-on-plate laser welds were made on an industrially produced DP780 steel to determine the effect of normalized welding heat input on the microstructure and mechanical properties within the weld fusion zone (FZ) and heat affected zone (HAZ) with reference to the base material (BM) mechanical properties. Normalized welding heat input was calculated using an established model from the literature utilizing measurements from the weld cross-section microstructures along with known materials properties. Microhardness profiles and optical microscopy were employed to evaluate materials properties and microstructural changes across the various microstructural zones of each weld. The mechanical properties of the welds were evaluated globally through standard ASTM tensile specimens as well as through a series of specialized mechanical testing sample geometries which examined the properties of individual microstructural zones. These specialized sample geometries included non-standard uniaxial and plain strain tension where effective stress and effective strains were used to compare the mechanical properties across samples. It was determined that there was a good correlation between ASTM standard samples and the specialized sample geometries employed in this study and that the UTS and YS values obtained in both cases were comparable. Sigmoidal decay behaviour was observed in the UTS and YS with increasing heat input for both the FZ and HAZ of all welds. It was found that welds with heat inputs greater than 60 J/mm2 had both a UTS and YS which were significantly depressed in the FZ and HAZ when compared to the base material values. Conversely, welds with heat inputs below 36.3 J/mm2 were found to have a UTS and YS in both the FZ and HAZ microstructural zones which were above the values determined for the BM. When global weld properties were tested, it was found that welds with a heat input greater than 60.0 J/mm2 failed within the HAZ while welds with heat inputs below 36.3 J/mm2 failed within the BM. It has been shown that there is a significant correlation between the heat inputs of laser welded DP steels and both the mechanical properties and microstructural features of the various microstructural zones as well as the location of failure during weld tensile testing. It has also been demonstrated that the mechanical properties of weld microstructural zones can be qualitatively evaluated using specialized tensile testing geometries. / Thesis / Master of Applied Science (MASc)

Super duplex stainless steels are applied in highly corrosive environments. To withstand such conditions, they designed with increased content of alloying elements and a duplex microstructure consisting of austenitic and ferritic phases. The result of this combination is the desired improvement in corrosion resistance, but also, the enhancement of mechanical properties. Machining super duplex stainless steels involves strain hardening of the workpiece, intense adhesive wear and elevated temperatures within the cutting zone leading to rapid tool wear and poor machined surface integrity. This research pertains to the application of commercially available PVD coatings to minimize the detrimental effects when turning super duplex stainless steel S32750. The selected coatings for this study were Alcronos (AlCrN), Alnova (AlCrN + AlCrSiN), Formera (CrN + CrAlTiN), Croma Plus (Cr + CrN + OX), Fortiphy (CrN) and Certiphy (TiAlN). The wear behavior and mechanisms in two distinct machining experiments were evaluated, and all tools failed by chipping preceded by intense adhesive wear and BUE formation. The use of AlCrN coatings improved tool life significantly. Data on the cutting force, chip formation, and workpiece surface integrity indicate less workpiece strain hardening effects, improved friction conditions at the tool/chip interface, as well as thinner chips being formed when machining with Alcronos coated carbide inserts. The micro-mechanical properties of the selected coatings were assessed and Alcronos combined high hardness and elastic modulus with a high plasticity index value that allows this coating to better manage the friction in the cutting zone and better dissipate the energy generated during cutting. / Thesis / Master of Applied Science (MASc) / Super duplex stainless steels are designed to be applied in highly corrosive environments. Like any other stainless steels, processing the super duplex grade can be challenging, especially when it comes to machining. The major causes of poor machined surface quality and rapid tool wear are high temperature, the workpiece enhanced mechanical properties, surface hardening and the tendency to stick to the cutting tool causing adhesive wear. This research explores the application of coated cutting tools to improve the machinability of the super duplex stainless steel UNS S32750. Different commercially available coatings were tested and two, Alcronos and Alnova, improved tool life significantly. These two coatings were capable of improving the friction conditions within the cutting zone which, in turn, helps with the formation of the chips and leads to a better machined surface integrity and an approximately 5 to 6 times longer tool life.

Yes / Brittleness in manganese steels can be associated with processing in a "wet¿ [micro]climate resulting in the formation of continuous oxide networks. The formation of these networks can be prevented by sintering in an atmosphere, also ¿local¿ in a semiclosed container, adhering to the Ellingham-Richardson oxide reduction criteria. When this requirement is satisfied, however, further types of ductile ¿ brittle transitions are observed. Rapid cooling, typically above 40°C/min, produces enough martensite to render Fe-(3-4)Mn-(0·6-0·7)C material macroscopically brittle. Quenched and conventionally tempered structures remain brittle. It is tentatively suggested that segregation of minor alloying/tramp element(s), as in cast materials, is responsible for this temper embrittlement. To overcome it, heat treatment at a temperature no higher than 200°C, recovery/stress relief, is recommended.

No description available.

No description available.

Materials to be used in thermal power plants have to resist creep deformation for time periods up to 30 years. The role of alloying elements for creep strength of 9-12% Cr steels is analysed. The creep strength in these steels relies on minor additions of alloying elements. Precipitates give rise to the main strengthening and remaining elements produce solid solution hardening. Nucleation, growth and coarsening of particles are predicted by thermodynamic modelling. Phase fractions and size distributions of M23C6 carbides, MX carbonitrides and Laves phase are presented. The size distributions are needed in order to determine the particle hardening during creep. At elevated temperatures the climb mobility is so high that the dislocations can climb across particles instead of passing by making Orowan loops. By solving Fick's second law the concentration profile around a moving dislocation can be determined. The results show an accumulation of solutes around the dislocation that slows down dislocation movement. When Laves phase grows a decrease in creep strength is observed due to a larger loss in solid solution hardening than strength increase by particle hardening. Solid solution hardening also gives an explanation of the low dislocation climb mobility in 9-12% Cr steels. Three different dislocation types are distinguished, free dislocations, immobile dislocation and immobile boundary dislocations. This distinction between types of dislocations is essential in understanding the decreasing creep with strain during primary creep. The empirical relation with subgrain size inversely proportional to stress has been possible to predict. The total creep strength can be predicted by adding the contribution from individual mechanisms. / QC 20101112

Intercritically annealed medium manganese steels are a promising third-generation advanced high-strength steel candidate, relying on large fractions of Mn-enriched retained austenite for excellent strength-ductility combinations. The present study proposes a novel cyclic intercritical annealing to promote nucleation and efficient stabilization of austenite in a medium Mn microstructure. Design of the heat treatment is driven by the hypothesis that the distribution of ductile austenite is key in mitigating the strain incompatibility that accelerates failure in these steels. Development and preliminary testing of the heat treatment are first detailed and compared with literature results for equivalent isothermal annealing. The effects of cyclic annealing parameters on the amount and stability of retained austenite are also explored through diffraction methods and mechanical testing. Finally, steps are taken towards quantifying austenite formation during the cyclic treatment, and recommendations are made for adapting the designed heat treatment to thicker gauges.

<p> Intercritically annealed steels, such as dual-phase steels, have found widespread use in automotive structural components due to their high strength and ductility. Elements such as Mn, Al and Si, added to improve the mechanical properties are selectively oxidized during heat treatment and limit the ability of the alloy to be reactively wet during continuous hot-dip galvanizing. Subsequently, a limit has been placed on the amount of alloy which can be used if the steel is to be subsequently galvanized. The specifics of this limit have not been explored in detail, nor has the mechanism of decreased wettability been well demonstrated in the literature other than to say that the galvanizing reaction is limited by oxides on the surface.</p> <p> Using a force balance, it is shown that the presence of MnO on the surface of steels greatly reduces the wettability with a typical galvanizing bath (Zn-0.2wt%Al, Fe-saturated, 460°C). Furthermore, it was determined that this is caused by the additional and rate-limiting step of aluminothermic reduction of the oxide layer with the bath Al, required for subsequent inhibition layer formation. By using a low pO2 during annealing, the wettability was improved by reducing the thickness of the MnO layer when compared to intermediate and industrially common values of pO2. Using a high pO2 also resulted in improved wettability since the internal oxide which was formed did not reduce the wettability since it was not exposed to the bath alloy.</p> <p> Improvements in hardenability were also explored via dilatometry showing that the formation of bainite is delayed with increasing Mn content, as well as a decrease in transformation temperatures from γ during cooling (i.e. Ms and Bs). At ~5wt% Mn, only the the transformation to αM could be observed. This opens the door to higher strength, galvanized steels - as well as possibly galvanized martensitic steels.</p> / Thesis / Master of Applied Science (MASc)

<p> Case hardening of steels is extensively used throughout general engineering to produce components with a hardened layer whilst retaining a tough core. This is usually accomplished using different sources of energy, e.g. flame and induction being the most common. In recent years, a new case hardening technology, named 'Grind-Hardening' has surfaced. In this method, the heat dissipated during grinding is utilized to induce martensitic phase transformation in the surface layer of a component. Therefore it is possible to incorporate grinding and surface hardening into a single operation to develop a cost-effective production method. The grinding process then becomes an integrated heat treatment process.</p> <p> In the present study on 'grind hardening', a numerical thermal model has been developed to compute the temperature distribution beneath the ground surface to predict the extent of surface hardening and the case depth. Grinding experiments were conducted in order to examine the influence of various process variables such as wheel depth of cut, feed speed, and wheel preparation. AISI 52100 and 1045 steels were used in this study to evaluate the behavior of plain and alloy steels during grind hardening. Effective case depth was measured using a Vickers hardness tester and was found to be over 0.5 mm for a target hardness of 513 Hv. Microstructure was analyzed using optical and scanning electron microscopes. The microstructure was observed to have fine martensitic laths which give rise to remarkable high hardness.</p> / Thesis / Master of Applied Science (MASc)

Third generation advanced high-strength steels (3G-AHSS) have received significant interest from leading auto steel industries and OEMs as candidate materials for reduced mass Body In White (BIW) components due to their unique combination of high specific strength and ductility. However, the continuous hot-dip galvanizing of these steels is challenging due to selective oxidation of the main alloying elements such as Mn, Si, Al and Cr at the steel surface during the annealing step prior to immersion in the galvanizing Zn(Al, Fe) bath, as extensive coverage of the substrate surface by these oxides is detrimental to reactive wetting, good coating adhesion and integrity. Simulated galvanizing treatments were conducted on two prototype Fe-0.1C-6Mn-2Si (wt pct) 3G steels; one as the reference steel and the other with 0.05 wt pct Sn added to the composition. The combined effects of annealing temperature, time, process atmosphere oxygen partial pressure and 0.05 wt pct Sn addition on the selective oxidation of the steel substrates were determined. Subsequently, the reactive wetting of the steels with respect to the pre-immersion surface structures of the samples annealed for 120 s was examined. Annealing heat treatments were carried out at 800˚C and 690˚C in a N2-5 vol pct H2 process atmosphere under three dew points of –50˚C, –30˚C and +5˚C, covering process atmosphere oxygen partial pressures within the range of 1.20  10-27 atm to 1.29  10-20 atm. MnO was present at the outmost layer of the external oxides on all samples after annealing. However, the morphology, distribution, thickness and surface coverage were significantly affected by the experimental variables. Annealing the reference steel under the low dew point process atmospheres, i.e. –50˚C and –30˚C, resulted in the highest Mn surface concentration as well as maximum surface oxide coverage and thickness. The oxides formed under these process atmospheres generally comprised coarse, compact and continuous film forming nodules, whereas the surface morphologies and distributions obtained under the +5˚C dew point process atmosphere, which was consistent with the internal oxidation mode, exhibited wider spacing between finer and thinner MnO nodules. The grain boundary internal oxide networks had a multi layer structure with SiO2 and MnSiO3 at the oxide cores and shells, respectively. Significant morphological changes were obtained as a result of Sn addition. The continuous film-like external MnO nodules were modified to a fine and discrete globular morphology, with less surface coverage by the oxides and reduced external oxide thickness. Both the external and internal oxidations followed parabolic growth kinetics, where the depth of the internal oxidation zone decreased with Sn addition and decreasing oxygen partial pressure. Poor reactive wetting was observed for the reference steel substrates that were annealed for 120 s under the –50˚C and –30˚C dew point process atmospheres at 800˚C and under the –50˚C dew point atmosphere at 690˚C, such that no integral metallic coating was formed after the 4 s immersion in the Zn(Al, Fe) bath. By contrast, excellent coating quality was obtained for the Sn-added steels when the –30˚C and +5˚C dew point process atmospheres were employed when annealing at 690˚C. The remainder of the experimental conditions demonstrated good reactive wetting with intermediate coating quality. For the two reference steels annealed at 800˚C under the –50˚C and –30˚C dew point process atmospheres, poor reactive wetting was due to full coverage of the surface by 116 nm and 121 nm thick and continuous MnO films. In the case of the 690˚C  –50˚C reference steel with the external layer thickness of only 35 nm, however, poor wetting was attributed to substantial coverage of the surface by continuous, film-like oxides. In both cases, exposure of the underlying substrate to the bath alloy and an intimate contact between the substrate Fe and the bath dissolved Al could not take place and the formation of the Fe2Al5Znx interfacial layer was hidered. For the processing conditions that satisfactory reactive wetting was obtained despite the pre-immersion selective oxidation of the surfaces, several reactive wetting mechanisms were determined. For the samples with a sufficiently thin external MnO layer, good reactive wetting was attributed to partial reduction of MnO by the bath dissolved Al, as well as bridging of the Mn sub-oxides by the Zn coating or Fe2Al5Znx interfacial intermetallics. Partial or full formation of the Fe2Al5Znx interfacial layer was observed in the successfully galvanized substrates with Fe-Al crystals formed between, underneath and also on top of the reduced oxides. Furthermore, for cases with widely-spaced, fine oxide nodules, it was found that the liquid bath alloy was able to infiltrate the external oxide/substrate interface, resulting in surface oxide lift-off and enhanced coating adhesion. It was globally concluded that the thin, discrete and fine globular morphology of external MnO, resultant of annealing the steel substrates with 0.05 wt pct Sn addition under the process atmosphere oxygen partial pressures consistent with internal oxidation, allowed for an enhanced reactive wetting by the Zn(Al, Fe) galvanizing bath which was manifested by increased amount of Al uptake and population of the Fe2Al5Znx intermetallics at the coating/steel interface. / Thesis / Doctor of Science (PhD)