From the Proceedings of the 1975 Meetings of the Arizona Section - American Water Resources Assn. and the Hydrology Section - Arizona Academy of Science - April 11-12, 1975, Tempe, Arizona / Evaporation of water from bare soils is an important consideration in the scheduling of many farming operations in both irrigated and dryland agriculture. Accurate predictions of bare soil evaporation can serve as the basis for decisions to increase the acreage planted with a given crop. An alternative is presented to previous approaches to bare soil evaporation estimation by empirically correlating the ratio of daily totals of actual to potential evaporation and the amplitude of the diurnal surface soil temperature wave. Since evaporation is directly related to the surface soil water pressure, the soil thermal inertia technique might be capable of prescribing relative bare soil evaporation rates which, combined with potential evaporation calculations, could allow determination of actual evaporation rates over the entire range of soil drying.

Lignocellulosic biomass is composed of cellulose, hemicellulose, lignin and extraneous compounds (waxes, fats, gums, starches, alkaloids, resins, tannins, essential oils, silica, carbonates, oxalates, etc). The sugars within the complex carbohydrates (cellulose and hemicellulose) can be accessed for cellulosic bioethanol production through ethanologenic microorganisms. However, the composite nature of lignocellulosic biomass, particularly the lignin portion, presents resistance and recalcitrance to biological and chemical degradation during enzymatic hydrolysis/saccharification and the subsequent fermentation process. This leads to a very low conversion rate, which makes the process uneconomically feasible. Thus, biomass structure requires initial breakdown of the lignocellulosic matrix. In this study, two types of biomass pretreatment were applied on barley straw grind: radio-frequency (RF)-based dielectric heating technique using alkaline (NaOH) solution as a catalyst and steam explosion pretreatment at low severity factor. The pretreatment was applied on barley straw which was ground in hammer mill with a screen size of 1.6 mm, so as to enhance its accessibility and digestibility by enzymatic reaction during hydrolysis. Three levels of temperature (70, 80, and 90oC), five levels of ratio of biomass to 1% NaOH solution (1:4, 1:5, 1:6, 1:7, & 1:8), 1 h soaking time, and 20 min residence time were used for the radio frequency pretreatment. The following process and material variables were used for the steam explosion pretreatment: temperature (140-180oC), retention time (5-10 min), and 8-50% moisture content (w.b). The effect of both pretreatments was assessed through chemical composition analysis and densification of the pretreated and non-pretreated biomass samples. Results of this investigation show that lignocellulosic biomass absorbed more NaOH than water, because of the hydrophobic nature of lignin, which acts as an external crosslink binder on the biomass matrix and shields the hydrophilic structural carbohydrates (cellulose and hemicellulose). It was observed in the RF pretreatment that the use of NaOH solution and the ratio of biomass to NaOH solution played a major role, while temperature played a lesser role in the breakdown of the lignified matrix, as well as in the production of pellets with good physical quality. The heat provided by the RF is required to assist the alkaline solution in the deconstruction and disaggregation of lignocellulosic biomass matrix. The disruption and deconstruction of the lignified matrix is also associated with the dipole interaction, flip flop rotation, and friction generated between the electromagnetic charges from the RF and the ions and molecules from the NaOH solution and the biomass. The preserved cellulose from the raw sample (non-treated) was higher than that from the RF alkaline pretreated samples because of the initial degradation of the sugars during the pretreatment process. The same observation applies to hemicellulose. This implies that there is a trade-off between the breakdown of the biomass matrix/creating pores in the lignin and enhancing the accessibility and digestibility of the cellulose and hemicellulose. The use of dilute NaOH solution in biomass pretreatment showed that the higher the NaOH concentration, the lower was the acid insoluble lignin and the higher was the solubilized lignin moieties. The ratio of 1:6 at the four temperatures studied was determined to be the optimal. Based on the obtained data, it is predicted that this pretreatment will decrease the required amount and cost of enzymes by up to 64% compared to using non-treated biomass. However, the use of NaOH led to an increase in the ash content of biomass. The ash content increased with the decreasing ratio of biomass to NaOH solution. This problem of increased ash content can be addressed by washing the pretreated samples. RF assisted-alkaline pretreatment technique represents an easy to set-up and potentially affordable route for the bio-fuel industry, but this requires further energy analysis and economic validation, so as to investigate the significant high energy consumption during the RF-assisted alkaline pretreatment heating process. Data showed that in the steam explosion (SE) pretreatment, considerable thermal degradation of the energy potentials (cellulose and hemicellulose) with increasing acid soluble and insoluble lignin content occurred. The high degradation of the hemicellulose can be accounted for by its amorphous nature which is easily disrupted by external influences unlike the well-arranged crystalline cellulose. It is predicted that this pretreatment will decrease the required amount and cost of enzymes by up to 33% compared to using non-treated biomass.The carbon content of the solid SE product increased at higher temperature and longer residence time, while the hydrogen and oxygen content decreased. The RF alkaline and SE treatment combinations that resulted to optimum yield of cellulose and hemicellulose were selected and then enzymatically digested with a combined mixture of cellulase and β-glucosidase enzymes at 50oC for 96 h on a shaking incubator at 250 rev/min. The glucose in the hydrolyzed samples was subsequently quantified. The results obtained confirmed the effectiveness of the pretreatment processes. The average available percentage glucose yield that was released during the enzymatic hydrolysis for bioethanol production ranged from 78-96% for RF-alkaline pretreated and 30-50% for the SE pretreated barley straw depending on the treatment combination. While the non-treated sample has available average percentage glucose yield of just below 12%. The effects of both pretreatment methods (RF and SE) were further evaluated by pelletizing the pretreated and non-pretreated barley straw samples in a single pelleting unit. The physical characteristics (pellet density, tensile strength, durability rating, and dimensional stability) of the pellets were determined. The lower was the biomass:NaOH solution ratio, the better was the quality of the produced pellets. Washing of the RF-alkaline pretreated samples resulted in pellets with low quality. A biomass:NaOH solution ratio of 1:8 at the three levels of temperature (70, 80, and 90oC) studied are the RF optimum pretreatment conditions. The higher heating value (HHV) and the physical characteristics of the produced pellets increased with increasing temperature and residence time. The steam exploded samples pretreated at higher temperatures (180ºC) and retention time of 10 min resulted into pellets with good physical qualities. Fourier transform infrared-photoacoustic spectroscopy (FTIR-PAS) was further applied on the RF alkaline and SE samples in light of the need for rapid and easy quantification of biomass chemical components (cellulose, hemicellulose, and lignin). The results obtained show that the FTIR-PAS spectra can be rapidly used for the analysis and identification of the chemical composition of biofuel feedstock. Predictive models were developed for each of the biomass components in estimating their respective percentage chemical compositions.

Gelfill (GF) is made of tailings, water, binder and chemical additives (Fillset, sodium silicate gel). The components of GF are combined and mixed on the surface and transported (by gravity and/or pumping) to the underground mine workings, where the GF can be used for both underground mine support and tailings storage. Thermal (T), hydraulic (H), and mechanical (M) properties are important performance criteria of GF. The understanding of these engineering properties and their evolution with time are still limited due to the fact that GF is a new cemented backfill material. In this thesis, the evolution of the thermal, hydraulic, mechanical, and microstructural properties of small GF samples are determined. Various binder contents of Portland cement type I (PCI) are used. The GF is cured for 3, 7, 28, 90, and 120 days. It is found that the thermal, hydraulic and mechanical properties are time-dependent or affected by the degree of binder hydration index. Furthermore, a relationship is found between the compressive strength and the saturated hydraulic conductivity of the GF samples. The unsaturated hydraulic properties of GF samples have also been investigated. The outcomes show that unsaturated hydraulic conductivity is influenced by the degree of binder hydration index and binder content, especially at low suction ranges. Simple functions are proposed to predict the evolution of air-entry values (AEVs), residual water content, and fitting parameters from the van Genuchten model with the degree of hydration index (α). Furthermore, two columns are built to simulate the coupled thermo-hydro-mechanical (THM) behaviour of GF under drained and undrained conditions. The obtained results from the GF columns are compared with the small samples. It is observed that the mechanical properties, hydraulic properties (suction and water content), and temperature development are strongly coupled. The magnitude of these THM coupling factors is affected by the size of the GF. The findings also show that the mechanical, hydraulic and thermal properties of the GF columns are different from samples cured in plastic moulds.

Effect of architecture at nanoscale on the macroscopic properties of polymer materials has long been a field of major interest, as evidenced by inhomogeneities in networks, multimodal network topologies, etc. The primary purpose of this research is to establish the architecture-property relationship of polymer networks by studying the physical and mechanical responses of a series of topologically different PTHF networks. Monodispersed allyl-terminated PTHF precursors were synthesized through ¡°living¡± cationic polymerization and functional end-capping. Model networks of various crosslink densities and inhomogeneities levels (unimodal, bimodal and clustered) were prepared by endlinking precursors via thiol-ene reaction. Thermal characteristics, i.e., glass transition, melting point, and heat of fusion, of model PTHF networks were investigated as functions of crosslink density and inhomogeneities, which showed different dependence on these two architectural parameters. Study of freezing point depression (FPD) of solvent confined in swollen networks indicated that the size of solvent microcrystals is comparable to the mesh size formed by intercrosslink chains depending on crosslink density and inhomogeneities. Relationship between crystal size and FPD provided a good reflection of the existing architecture facts in the networks. Mechanical responses of elastic chains to uniaxial strains were studied through SANS. Spatial inhomogeneities in bimodal and clustered networks gave rise to ¡°abnormal butterfly patterns¡±, which became more pronounced as elongation ratio increases. Radii of gyration of chains were analyzed at directions parallel and perpendicular to stretching axis. Dependence of Rg on ¦Ë was compared to three rubber elasticity models and the molecular deformation mechanisms for unimodal, bimodal and clustered networks were explored. The thesis focused its last part on the investigation of evolution of free volume distribution of linear polymer (PE) subjected to uniaxial strain at various temperatures using a combination of MD, hard sphere probe method and Voronoi tessellation. Combined effects of temperature and strain on free volume were studied and mechanism of formation of large and ellipsoidal free volume voids was explored.

Divertors are in-vessel, plasma-facing, components in magnetic-confinement fusion reactors. Their main function is to remove the fusion reaction ash (α-particles), unburned fuel, and eroded particles from the reactor, which adversely affect the quality of the plasma. A significant fraction (~15 %) of the total fusion thermal power is removed by the divertor coolant and must, therefore, be recovered at elevated temperature in order to enhance the overall thermal efficiency. Helium is the leading coolant because of its high thermal conductivity, material compatibility, and suitability as a working fluid for power conversion systems using a closed high temperature Brayton cycle. Peak surface heat fluxes on the order of 10 MW/m^2 are anticipated with surface temperatures in the region of 1,200°C to 1,500°C. Recently, several helium-cooled divertor designs have been proposed, including a modular T-tube design and a modular finger configuration with jet impingement cooling from perforated end caps. Design calculations performed using the FLUENT® CFD software package have shown that these designs can accommodate a peak heat load of 10 MW/m^2. Extremely high heat transfer coefficients (~50,000 W/(m^2 K)) were predicted by these calculations. Since these values of heat transfer coefficient are considered to be outside of the experience base for gas-cooled systems, an experimental investigation has been undertaken to validate the results of the numerical simulations. Attention has been focused on the thermal performance of the T-tube and the finger divertor designs. Experimental and numerical investigations have been performed to support both divertor geometries. Excellent agreement has been obtained between the experimental data and model predictions, thereby confirming the predicted performance of the leading helium-cooled divertor designs for near- and long-term magnetic fusion reactor designs. The results of this investigation provide confidence in the ability of state-of-the-art CFD codes to model gas-cooled high heat flux plasma-facing components such as divertors.

[Truncated abstract] Rocks, as the host to natural chains of coupled thermal, hydraulic and mechanical processes, are heterogeneous at a variety of length scales, and in their mechanical properties, as well as in the hydraulic and thermal transport properties. Rock heterogeneity affects the ultimate hydro-carbon recovery or geothermal energy production. This heterogeneity has been considered one important and difficult problem that needs to be taken into account for its effect on the coupled processes. The aim of this thesis is to investigate the effect of rock heterogeneity on multi-physical processes. A fully coupled finite element model, hereinafter referred to as a porosity-based model (PBM) was developed to characterise the thermal-hydraulic-mechanical (THM) coupling processes. The development of the PBM consists of a two-staged workflow. First, based on poromechanics, porosity, one of the inherent rock properties, was derived as a variant function of the thermal, hydraulic and mechanical effects. Then, empirical relations or experimental results, correlating porosity with the mechanical, hydraulic and thermal properties, were incorporated as the coupling effects. In the PBM, the bulk volume of the model is assumed to be changeable. The rate of the volumetric strain was derived as the difference of two parts: the first part is the change in volume per unit of volume and per unit of time (this part was traditionally considered the rate of volumetric strain); and the second is the product of the first part and the volumetric strain. The second part makes the PBM a significant advancement of the models reported in the literature. ... impact of the rock heterogeneity on the hydro-mechanical responses because of the requirement of large memory and long central processing unit (CPU) time for the 3D applications. In the 2D PBM applications, as the thermal boundary condition applied to the rock samples containing some fractures, the pore pressure is generated by the thermal gradient. Some pore pressure islands can be generated as the statistical model and the digital image model are applied to characterise the initial porosity distribution. However, by using the homogeneous model, this phenomenon cannot be produced. In the 3D PBM applications, the existing fractures become the preferential paths for the fluid flowing inside the numerical model. The numerical results show that the PBM is sufficiently reliable to account for the rock mineral distribution in the hydro-mechanical coupling processes. The applications of the statistical method and the digital image processing technique make it possible to visualise the rock heterogeneity effect on the pore pressure distribution and the heat dissipation inside the rock model. Monitoring the fluid flux demonstrates the impact of the rock heterogeneity on the fluid product, which concerns petroleum engineering. The overall fluid flux (OFF) is mostly overestimated when the rock and fluid properties are assumed to be homogeneous. The 3D PBM application is an example. As the rock is heterogeneous, the OFF by the digital core is almost the same as that by the homogeneous model (this is due to that some fractures running through the digital core become the preferential path for the fluid flow), and around 1.5 times of that by the statistical model.

Made available in DSpace on 2014-12-17T14:07:07Z (GMT). No. of bitstreams: 1 MarcioCSM_TESE.pdf: 957118 bytes, checksum: 7c10d815ada900ecb0efde8936a6064e (MD5) Previous issue date: 2011-07-29 / The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ? showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes. / A crescente preocupa??o com a gest?o de res?duos s?lidos, observada na ?ltima d?cada, em virtude de sua enorme quantidade e impacto ambiental, tem motivado a busca por processos de reciclagem, onde estes res?duos podem ser reprocessados de modo a gerarem novos produtos, ampliando o ciclo dos materiais e energia neles contidos. Dentre os res?duos polim?ricos, destaca-se o poli(tereftalato de etileno) (PET). O PET ? utilizado em embalagens de alimentos, preferencialmente, no envase de bebidas carbonatadas. A reintegra??o do PET p?s-consumo ao meio produtivo pode ser considerada uma a??o mitigat?ria dos impactos ambientais causados por estes res?duos e j? ? realizada por meio da obten??o de diversos produtos diferentes ao da origem, ou seja, embalagens para alimento, com taxas de reciclagem crescente a cada ano. Este trabalho focou o desenvolvimento e a caracteriza??o mec?nica, t?rmica, termo-mec?nica, termo-din?mico-mec?nica e morfol?gica do PET reciclado processado e dos comp?sitos de PET reciclado com flocos de vidro na fra??o em peso de 5%, 10% e 20% processados em uma extrusora rosca simples, utilizando as seguintes t?cnicas de an?lise: termogravimetria (TG), calorimetria explorat?ria diferencial (DSC), tra??o uniaxial, impacto Izod, dureza Rockwel, temperatura de amolecimento Vicat, ?ndice de fluidez, taxa de queima, an?lise termo-din?mico-mec?nica (DMTA) e microscopia eletr?nica de varredura (MEV). Os resultados das an?lises t?rmicas e das propriedades mec?nicas conduziram a uma avalia??o positiva, pois nos termogramas as adi??es dos flocos de vidro mostraram comportamento crescente nas temperaturas inicial de decomposi??o t?rmica e de fus?o cristalina, al?m disso, observou-se comportamento crescente no desempenho mec?nico dos comp?sitos polim?ricos, cuja estrutura morfol?gica foi observada por MEV, verificando uma boa distribui??o dos flocos de vidro, apresentando diferen?a na orienta??o no centro e na camada superficial do corpo de prova dos comp?sitos com 10 e 20% de flocos de vidro. Nos resultados de DMTA os valores de Tg dos comp?sitos obtidos a partir do pico de tan ?, apresentaram pequenas redu??es, devido a pobre ades?o interfacial entre o PET reciclado e os flocos de vidro.

Le secteur du bâtiment recèle un fort potentiel d’amélioration de l'efficacité énergétique et de réduction de l’empreinte écologique. Dans cette optique, l’enveloppe du bâtiment joue un rôle important pour relever le défi de la transition énergétique. En effet, une bonne conception de l’enveloppe contribue efficacement à réduire la consommation d’énergie tout en réduisant les émissions de CO2 associés. Cela s’accompagne notamment d’une démarche de développement de nouveaux matériaux et principes constructifs. Ce projet de thèse s’inscrit dans ce cadre en proposant un nouveau matériau composite, qui porte sur l’association de deux matériaux innovant : composite textile mortier (TRC) et matériaux à changement de phase (MCPs). L’objectif de cette combinaison est de contribuer au développement d’éléments de façades multifonctionnelles permettant d’allier performances énergétiques, mécaniques et environnementales. Le but de notre étude est de caractériser en premier lieu, les propriétés mécaniques et thermiques de ces composites puis, d’évaluer l’impact des MCPs sur le confort thermique intérieur pour différentes configurations. Pour atteindre ces objectifs, nous avons adopté une démarche expérimentale et numérique multi échelle. Une campagne expérimentale à l’échelle du laboratoire et in-situ a été menée. En parallèle, nous avons développé un modèle numérique de paroi multicouche, couplé à un modèle de bâtiment. Enfin, nous avons exploité ce couplage pour réaliser une optimisation multicritère à base d’algorithmes génétiques. / The building sector has a great potential to improve energy efficiency and reduce the greenhouse gas emissions. Improvements to the building envelope and Innovations in building materials have the potential to achieve sustainability within the built environment. This PhD thesis focuses on the development of multifunctional façade elements in order to optimize the building energy consumption while maintaining an optimal indoor human thermal comfort. The proposed solution consist of using passive storage by means of phase change materials associated with alternative construction materials such as textile reinforced concrete (TRC). The aim of the study is to characterize mechanical and thermal properties of TRC composites and to evaluate the effect of PCMs on indoor thermal comfort. To meet these objectives, experimental devices have been set up for the characterization (at the component scale and in situ) of the mechanical and thermal behaviour of different TRC panels. In parallel, we have developed a numerical model for the prediction of wall temperature profiles. Finally, a multi-objective optimization of the façade elements is carried out using genetic algorithms to determine the better combinations able to combine the energy performance with the mechanical performance.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Neste trabalho, desenvolveu-se um sistema de detecção fotoacústico para medidas simultâneas e independentes dos sinais fotoacústicos dianteiro e traseiro, utilizando dois microfones e um único feixe de excitação. Utiliza-se a diferença de fase entre estes sinais para a determinação da difusividade térmica de materiais, com base na abordagem teórica da técnica da Diferença de Fase dos Dois Feixes (T2F). Na metodologia apresentada não há a necessidade de se alternar o feixe de excitação entre as faces da amostra. Esta característica torna mais rápido o procedimento de medida e simplifica o monitoramento automatizado de processos dinâmicos que afetam a difusividade térmica do material, como a cura de resinas poliméricas. É apresentado o procedimento utilizado para determinar a diferença entre as fases intrínsecas dos microfones e o método empregado para compensar tal diferença e, assim, obter a defasagem entre os sinais fotoacústicos dianteiro e traseiro. O sistema de detecção desenvolvido é avaliado em medidas de difusividade térmica de amostras metálicas (aço inoxidável AISI 304 e aço SAE 1020) e poliméricas (polipropileno e polietileno de baixa densidade). Os resultados obtidos concordam de forma satisfatória com dados disponíveis na literatura. Finalmente, a aplicação do sistema proposto ao monitoramento de cura de amostras de resina epóxi indicou sua potencialidade de acompanhar, em tempo real, este tipo de processo dinâmico. / In this work, a photoacoustic detection system was developed for simultaneous and independent measurements of both front and rear photoacoustic signals, using two microphones and a single beam illumination mode. The phase-lag between these signals is used in the determination of thermal diffusivity of materials, based on the theoretical approach of the Two-Beam Phase-Lag technique. In the experimental setup presented in this work there is no need to alternate the light beam between the sample surfaces. This feature provides faster measurements and simplify the automated monitoring of dynamic processes that affect the material thermal diffusivity, as crosslinking processes. The procedure to determine the difference between the intrinsic phases of the microphones is presented, as well as the method to compensate this difference and to obtain the phase-lag between front and rear photoacoustic signals. The developed detection system is tested in thermal diffusivity measurements of metallic (AISI 304 stainless steel and SAE 1020 steel) and polymeric (polypropylene and low-density polyethylene) samples. The results are in good agreement with the available literature values. Finally, the system here proposed is applied in studies of epoxy resin curing, which shows its potentiality for real-time monitoring of dynamic process.

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior / Neste trabalho, desenvolveu-se um sistema de detecção fotoacústico para medidas simultâneas e independentes dos sinais fotoacústicos dianteiro e traseiro, utilizando dois microfones e um único feixe de excitação. Utiliza-se a diferença de fase entre estes sinais para a determinação da difusividade térmica de materiais, com base na abordagem teórica da técnica da Diferença de Fase dos Dois Feixes (T2F). Na metodologia apresentada não há a necessidade de se alternar o feixe de excitação entre as faces da amostra. Esta característica torna mais rápido o procedimento de medida e simplifica o monitoramento automatizado de processos dinâmicos que afetam a difusividade térmica do material, como a cura de resinas poliméricas. É apresentado o procedimento utilizado para determinar a diferença entre as fases intrínsecas dos microfones e o método empregado para compensar tal diferença e, assim, obter a defasagem entre os sinais fotoacústicos dianteiro e traseiro. O sistema de detecção desenvolvido é avaliado em medidas de difusividade térmica de amostras metálicas (aço inoxidável AISI 304 e aço SAE 1020) e poliméricas (polipropileno e polietileno de baixa densidade). Os resultados obtidos concordam de forma satisfatória com dados disponíveis na literatura. Finalmente, a aplicação do sistema proposto ao monitoramento de cura de amostras de resina epóxi indicou sua potencialidade de acompanhar, em tempo real, este tipo de processo dinâmico. / In this work, a photoacoustic detection system was developed for simultaneous and independent measurements of both front and rear photoacoustic signals, using two microphones and a single beam illumination mode. The phase-lag between these signals is used in the determination of thermal diffusivity of materials, based on the theoretical approach of the Two-Beam Phase-Lag technique. In the experimental setup presented in this work there is no need to alternate the light beam between the sample surfaces. This feature provides faster measurements and simplify the automated monitoring of dynamic processes that affect the material thermal diffusivity, as crosslinking processes. The procedure to determine the difference between the intrinsic phases of the microphones is presented, as well as the method to compensate this difference and to obtain the phase-lag between front and rear photoacoustic signals. The developed detection system is tested in thermal diffusivity measurements of metallic (AISI 304 stainless steel and SAE 1020 steel) and polymeric (polypropylene and low-density polyethylene) samples. The results are in good agreement with the available literature values. Finally, the system here proposed is applied in studies of epoxy resin curing, which shows its potentiality for real-time monitoring of dynamic process.