Yttria stabilized zirconia (YSZ) is the state of the art ceramic top coat material used for TBC applications. The desire to achieve a higher engine efficiency of agas turbine engine by increasing the turbine inlet temperature has pushed YSZ toits upper limit. Above 1200°C, issues such as poor phase stability, high sinteringrates, and susceptibility to CMAS (calcium magnesium alumino silicates) degradation have been reported for YSZ based TBCs. Among the new materials,gadolinium zirconate (GZ) is an interesting alternative since it has shown attractive properties including resistance to CMAS attack. However, GZ has a poor thermo-chemical compatibility with the thermally grown oxide leading to poor thermal cyclic performance of GZ TBCs and that is why a multi-layered coating design seems feasible.This work presents a new approach of depositing GZ/YSZ multi-layered TBCs by the suspension plasma spray (SPS) process. Single layer YSZ TBCs were also deposited by SPS and used as a reference.The primary aim of the work was to compare the thermal conductivity and thermal cyclic life of the two coating designs. Thermal diffusivity of the YSZ single layer and GZ based multi-layered TBCs was measured using laser flash analysis (LFA). Thermal cyclic life of as sprayed coatings was evaluated at 1100°C, 1200°C and 1300°C respectively. It was shown that GZ based multi-layered TBCs had a lower thermal conductivity and higher thermal cyclic life compared to the single layer YSZ at all test temperatures. The second aim was to investigate the isothermal oxidation behaviour and erosion resistance of the two coating designs. The as sprayed TBCs were subjected toisothermal oxidation test at 1150°C. The GZ based multi-layered TBCs showed a lower weight gain than the single layer YSZ TBC. However, in the erosion test,the GZ based TBCs showed lower erosion resistance compared to the YSZ singlelayer TBC. In this work, it was shown that SPS is a promising production technique and that GZ is a promising material for TBCs.

Reducing the heat losses in heavy-duty diesel engines is of importance for improving engine efficiency and reducing CO2 emissions. Depositing thermal barrier coatings (TBCs) onto engine components has been demonstrated to have great potential to reduce heat loss from the combustion chamber as well as from exhaust components. The overall aim of this thesis is to evaluate the thermal cycling lifetime and thermal insulation properties of TBCs for the purpose of reducing heat losses and thermal fatigue in heavy-duty diesel engines. In the thermal cycling test inside exhaust manifolds, nanostructured yttria-stabilized zirconia (YSZ) performed best, followed by YSZ with conventional microstructure and then La2Zr2O7. Forsterite and mullite could not withstand the thermal cycling conditions and displayed large cracks or spallation. Two sol-gel composite coatings displayed promising thermal cycling performance results in a furnace test under similar conditions. Thermal cycling testing of YSZ coatings having different types of microstructure, in a furnace at temperatures up to 800°C, indicated that the type of microstructure exerted a great influence. For the atmospheric plasma sprayed coatings, a segmented microstructure resulted in the longest thermal cycling lifetime. An even longer lifetime was seen for a plasma spray–physical vapour deposition (PS-PVD) coating. In situ heat flux measurements inside the combustion chamber indicated that plasma-sprayed Gd2Zr2O7 was the TBC material providing the largest heat flux reduction. This is explained by a combination of low thermal conductivity and high reflectance. The plasma-sprayed YSZ and La2Zr2O7 coatings provided very small heat flux reductions. Long-term testing indicated a running-in behaviour of YSZ and Gd2Zr2O7, with a reduction in heat flux due to the growth of microcracks in YSZ and the growth of macrocracks in Gd2Zr2O7. / <p>QC 20170821</p>

The durability of Thermal Barrier Coatings (TBCs) used on the turbine blades of aircraft and power generation engines has been known to be affected by sand particle ingression comprised of Calcium-Magnesium-Alumina-Silicate (CMAS). Previous studies have shown that these effects present themselves through variations in the thermomechanical and thermochemical properties of the coating. This study investigated the impact of CMAS ingression on the Yttria Stabilized Zirconia Topcoat (YSZ) and Thermally Grown Oxide (TGO) strain in sprayed Thermal Barrier Coating (TBC) samples of varying porosity with and without CMAS ingression. In-Situ Synchrotron X-ray Diffraction measurements were taken on the sample under thermal loading conditions from which the YSZ and TGO peaks were identified and biaxial strain calculations were determined at high temperature. Quantitative strain results are presented for the YSZ and TGO during a thermal cycle. In-plane strain results for YSZ near the TGO interface for a complete thermal cycle are presented, for a 6% porous superdense sample with CMAS infiltration. The outcomes from this study can be used to understand the role of CMAS on the strain tolerance of the TBC coating. It is well known that under engine operational conditions the development of the TGO layer, with large critical stresses, has been linked to failure of the coating. The growth of the TGO manifests as undulations in a series of peaks and troughs. Understanding the mechanics of the oxide layer at these locations provides significant information with respect to the failure mechanisms of the TBC coating. This study investigated the stress at the peak and trough of a TGO undulation for a cycled Dense Vertically Cracked (DVC) plasma sprayed TBC sample through photo-luminescence (PL) spectroscopy. High resolution nanoscale stress maps were taken nondestructively in the undulation of the TGO. Preliminary results from first line mapping of TGO peak and trough scan, at a resolution of 200 nm, have shown a non-uniform TGO stress variation. The results obtained from this study can be used to understand the stress variation in the peak and trough of a DVC sample's TGO undulation and how it contributes to the life of the TBC coating.

The development of thermal barrier coatings (TBCs) has been undoubtedly the most critical advancement in materials technology for modern gas turbine engines. TBCs are widely used in gas turbine engines for both power-generation and propulsion applications. Metallic oxidation-resistant coatings (ORCs) are also widely employed as a stand-alone protective coating or bond coat for TBCs in many high-temperature applications. Among the widely studied durability issues in these high-temperature protective coatings, one critical challenge that received greater attention in recent years is their resistance to high-temperature degradation due to corrosive deposits arising from fuel impurities and CMAS (calcium-magnesium-alumino-silicate) sand deposits from air ingestion. The presence of vanadium, sulfur, phosphorus, sodium and calcium impurities in alternative fuels warrants a clear understanding of high-temperature materials degradation for the development of fuel-flexible gas turbine engines. Degradation due to CMAS is a critical problem for gas turbine components operating in a dust-laden environment. In this study, high-temperature degradation due to aggressive deposits such as V2O5, P2O5, Na2SO4, NaVO3, CaSO4 and a laboratory-synthesized CMAS sand for free-standing air plasma sprayed (APS) yttria stabilized zirconia (YSZ), the topcoat of the TBC system, and APS CoNiCrAlY, the bond coat of the TBC system or a stand-alone ORC, is examined. Phase transformations and microstructural development were examined by using x-ray diffraction, scanning electron microscopy, and transmission electron microscopy. This study demonstrated that the V2O5 melt degrades the APS YSZ through the formation of ZrV2O7 and YVO4 at temperatures below 747°C and above 747°C, respectively. Formation of YVO4 leads to the depletion of the Y2O3 stabilizer and the deleterious transformation of the YSZ to the monoclinic ZrO2 phase. The investigation on the YSZ degradation by Na2SO4 and a Na2SO4 + V2O5 mixture (50-50 mol. %) demonstrated that Na2SO4 itself did not degrade the YSZ, however, in the presence of V2O5, Na2SO4 formed vanadates such as NaVO3 that degraded the YSZ through YVO4 formation at temperature as low as 700°C. The APS YSZ was found to react with the P2O5 melt by forming ZrP2O7 at all temperatures. This interaction led to the depletion of ZrO2 in the YSZ (i.e., enrichment of Y2O3 in t' -YSZ) and promoted the formation of the fluorite-cubic ZrO2 phase. Above 1250°C, CMAS deposits were observed to readily infiltrate and significantly dissolve the YSZ coating via thermochemical interactions. Upon cooling, zirconia reprecipitated with a spherical morphology and a composition that depended on the local melt chemistry. The molten CMAS attack destabilized the YSZ through the detrimental phase transformation (t - > t - > f + m). Free standing APS CoNiCrAlY was also prone to degradation by corrosive molten deposits. The V2O5 melt degraded the APS CoNiCrAlY through various reactions involving acidic dissolution of the protective oxide scale, which yielded substitutional-solid solution vanadates such as (Co,Ni)3(VO4)2 and (Cr,Al)VO4. The molten P2O5, on the other hand, was found to consume the bond coat constituents significantly via reactions that formed both Ni/Co rich phosphates and Cr/Al rich phosphates. Sulfate deposits such as Na2SO4, when tested in encapsulation, damaged the CoNiCrAlY by Type I acidic fluxing hot corrosion mechanisms at 1000°C that resulted in accelerated oxidation and sulfidation. The formation of a protective continuous Al2O3 oxide scale by preoxidation treatment significantly delayed the hot corrosion of CoNiCrAlY by sulfates. However, CoNiCrAlY in both as-sprayed and preoxidized condition suffered a significant damage by CaSO4 deposits via a basic fluxing mechanism that yielded CaCrO4 and CaAl2O4. The CMAS melt also dissolved the protective Al2O3 oxide scale developed on CoNiCrAlY by forming anorthite platelets and spinel oxides. Based on the detailed investigation on degradation of the APS YSZ and CoNiCrAlY by various corrosive deposits, an experimental attempt was carried out to mitigate the melt-induced deposit attack. Experimental results from this study demonstrate, for the first time, that an oxide overlay produced by electrophoretic deposition (EPD) can effectively perform as an environmental barrier overlay for APS TBCs. The EPD protective overlay has a uniform and easily-controllable thickness, uniformly distributed closed pores and tailored chemistry. The EPD Al2O3 and MgO overlays were successful in protecting the APS YSZ TBCs against CMAS attack and hot corrosion attack (e.g., sulfate and vanadate), respectively. Furnace thermal cyclic oxidation testing of overlay-modified TBCs on bond-coated superalloy also demonstrated the good adhesive durability of the EPD Al2O3 overlay.

Au cours de la dernière décennie, la technologie de projection à la torche à plasmasous très faible pression (VLPPS) (inférieure à 10 mbar) a attiré l’attention denombreux chercheurs car ce procédé permet d’envisager la possibilité de réaliser desdépôts de structure voisine de celle des dépôts en phase vapeur avec une cinétiqueproche de celle de la projection thermique classique. Cette technologie vise donc àévaporer totalement ou partiellement des poudres afin de déposer des revêtementsdenses avec une structure colonnaire ou mixte.Le travail effectué dans cette étude à consisté à étudier et à développer des moyenspour assurer la fusion et l’évaporation de matériaux céramiques en vue d’élaborer desrevêtements de haute qualité et à caractériser les propriétés de ces revêtements.Dans une première approche des dépôts denses et homogènes de zircone stabilisée àl’yttrine (YSZ) ont été obtenus sur un substrat « inox » en utilisant des torches àplasma « classiques » de type F100 et F4 sous très faible pression (1 mbar) en utilisantde façon originale un principe d’injection axiale via l’alimentation en gazplasmagènes. Un spectromètre d’émission optique a été utilisé pour analyser lespropriétés du jet de plasma et notamment apprécier le taux d’évaporation du matériau.La composition et la microstructure des dépôts ont été caractérisées par diffraction desrayons X et microscopie électronique à balayage. Les résultats ont montré que lapoudre YSZ a été partiellement évaporée et que les dépôts obtenus disposent d’unemicrostructure hybride composée de « splats » formés par des particules fondues etune « matrice » (en faible quantité) résultant de la condensation de vapeurs provenantde l’évaporation des particules surchauffées.Afin de tenter d’augmenter le taux de vaporisation, l’anode de la torche F100 a étéallongée et un dispositif d’arc transféré complémentaire a été réalisé afin d’éleverl’énergie du jet de plasma et de favoriser l’échange thermique. Les effets de cedispositif sur les propriétés du jet de plasma ont été évalués par spectrométried’émission optique et calcul de la température électronique. Des dépôts de YSZ etd’alumine (Al2O3) ont été élaborés à la pression de 1 mbar. Les dépôts de YSZ ontaffiché une microstructure hybride similaire à celle obtenue précédemment alors quepour les dépôts d’alumine, seul un dépôt lamellaire « classique » a été observé. Lacapacité d’évaporation est donc restée limitée. La microstructure, les propriétésmécaniques et les propriétés de résistance aux chocs thermiques des dépôts de YSZont été étudiées plus en détail et comparées avec celle de dépôts réalisés dans desconditions plus classiques. Une tenue améliorée en termes de résistance aux cyclagesthermiques a notamment été observée.Afin de répondre aux attentes en matière de niveau de densité de puissance du jet lelaboratoire s’est équipé d’une une nouvelle torche à plasma tri-cathode expérimentaleélaborée par la société AMT. Cette torche a été modélisée et testée dans un premiertemps en conditions atmosphériques, révélant une limitation importante du rendementde projection. A partir de ces premiers résultats expérimentaux une nouvellegéométrie de buse a été proposée afin d’améliorer le rendement de projection. Il aalors été constaté que le rendement de la projection avait été considérablementaugmenté par cette modification et que la microstructure du dépôt était également plusfavorable. Ce travail devra maintenant se poursuivre par l’intégration de cette torche dans l’enceinte sous pression réduite. / During the last decade, very low pressure plasma spraying (VLPPS) technology(below 10 mbar) attracted attention because it could allow to produce coatings with astructure similar to that of vapor deposited materials (PVD) with kinetics close to thatof thermal spray. This technology aims to fully or partially evaporate the feedstockmaterials in order to build rapidly dense, thin, and columnar coatings.The work during this thesis preparation was thus devoted to the study anddevelopment of tools and techniques allowing fusion and evaporation of ceramicmaterials in order to obtain high quality deposits with new performance and then tocharacterize the properties of those deposits. In a first approach dense and homogeneous yttria-stabilized zirconia (YSZ) coatingswere deposited successfully on a stainless steel substrate using “classical” plasmaspray torches such as F100 and F4 under very low pressure (1 mbar) by means ofusing an original way of introducing the feedstock material in the core of the plasmajet via the plasma gas port. Optical emission spectroscopy was used to analyze theproperties of the plasma jet and especially to observe the feedstock materialevaporation rate. The phase composition and the microstructure of the coatings werecharacterized by X-ray diffraction and scanning electron microscopy. Results showedthat the YSZ powder was partially evaporated and that the coatings possessed aduplex microstructure which was composed of splats formed by the impingement ofmelted particles and a little amount of a matrix formed by the condensation of thevapor emitted by overheated particles.In order to try and increase the evaporation rate, a home-made transferred arc nozzlewas made and mounted on a F100 plasma torch in order to enhance the energy levelof the plasma jet and then to increase thermal exchanges. The effects of thetransferred arc nozzle on the plasma jet properties were evaluated by optical emissionspectroscopy and electron temperature calculation. YSZ and alumina (Al2O3) coatingsWere elaborated using such a nozzle below 1 mbar. It was found that the YSZ coatingsdisplayed a duplex microstructure similar to that obtained in the previous experiments.However, no vapor condensation could be observed in the case of the Al2O3 coatingsindicating that the evaporation capacity of the system remained limited.The microstructure, the mechanical properties and the thermal shock resistance of theYSZ coatings were studied in more details and compared to that of deposits madeusing classical thermal spray routes. An enhanced resistance to thermal shock couldthus be observed for the coatings with a duplex structure.In order to find a solution for a substantial increase in the energy density of theplasma jet, the laboratory commissioned a novel experimental tri-cathode plasmatorch made to the AMT Company. This new torch was modeled and first testedunder atmospheric conditions, which revealed a poor spray yield. Following thosefirst experimental results, a modified nozzle was designed. As a result, the sprayefficiency was considerably increased and the coating fabricated by the tri-cathodetorch displayed a better microstructure. Now this work has to be pursued with theintegration of this torch in the low pressure spray tank.

The reliability of modern gas turbine engines is largely due to careful damage tolerant design a method of structural design based on the assumption that flaws (cracks) exist in any structure and will continue to grow with usage. With proper monitoring, largely in the form of periodic inspections at conservative intervals reliability and safety is maintained. These methods while reliable can lead to the early retirement of some components and unforeseen failure if design assumptions fail to reflect reality. With improvements to sensor and computing technology there is a growing interest in a system that could continuously monitor the health of structural aircraft as well as forecast future damage accumulation in real-time. Through the use of two-dimensional and three-dimensional numerical modeling the initial goals and findings for this continued work include: (a) establishing measurable parameters directly linked to the health of the blade and (b) the feasibility of detecting accumulated damage to the structural material and thermal barrier coating as well as the onset of damage causing structural failure.

The purpose of this research work was to develop a nozzle capable of depositing dense CoNiCrAlY coatings via cold gas dynamic spray (CGDS) as well as compare the oxidation performance of bond coats manufactured by CGDS, high-velocity oxy-fuel (HVOF) and air plasma spray (APS) at temperatures of 1000°C and 1100°C. The work was divided in two sections, the design and manufacturing of a CGDS nozzle with an optimal profile for the deposition of CoNiCrAlY powders and the comparison of the oxidation performance of CoNiCrAlY bond coats. Throughout this work, it was shown that the quality of coatings deposited via CGDS can be increased by the use of a nozzle of optimal profile and that early formation of protective α-Al2O3 due to an oxidation temperature of 1100°C as opposed to 1000°C is beneficial to the overall oxidation performance of CoNiCrAlY coatings.

The reliability of modern gas turbine engines is largely due to careful damage tolerant design a method of structural design based on the assumption that flaws (cracks) exist in any structure and will continue to grow with usage. With proper monitoring, largely in the form of periodic inspections at conservative intervals reliability and safety is maintained. These methods while reliable can lead to the early retirement of some components and unforeseen failure if design assumptions fail to reflect reality. With improvements to sensor and computing technology there is a growing interest in a system that could continuously monitor the health of structural aircraft as well as forecast future damage accumulation in real-time. Through the use of two-dimensional and three-dimensional numerical modeling the initial goals and findings for this continued work include: (a) establishing measurable parameters directly linked to the health of the blade and (b) the feasibility of detecting accumulated damage to the structural material and thermal barrier coating as well as the onset of damage causing structural failure.

The purpose of this research work was to develop a nozzle capable of depositing dense CoNiCrAlY coatings via cold gas dynamic spray (CGDS) as well as compare the oxidation performance of bond coats manufactured by CGDS, high-velocity oxy-fuel (HVOF) and air plasma spray (APS) at temperatures of 1000°C and 1100°C. The work was divided in two sections, the design and manufacturing of a CGDS nozzle with an optimal profile for the deposition of CoNiCrAlY powders and the comparison of the oxidation performance of CoNiCrAlY bond coats. Throughout this work, it was shown that the quality of coatings deposited via CGDS can be increased by the use of a nozzle of optimal profile and that early formation of protective α-Al2O3 due to an oxidation temperature of 1100°C as opposed to 1000°C is beneficial to the overall oxidation performance of CoNiCrAlY coatings.

The continuing quest for higher performance levels of modern gas turbine engines has been accompanied by the demand for higher engine operating temperatures. The use of Thermal Barrier Coatings (TBCs) enabled gas turbines to operate at higher temperatures by protecting the blade material (nickel superalloy) while operating in extreme environments. The TBC system typically consists of a bond coat for protection of the nickel–based superalloy against oxidation followed by a top coat consisting of a thermally insulating zirconia-yttria. In addition to the complex gradation in phases, the coatings are subjected to continuous oxidation with service exposure, mechanical loading on rotating parts, fatigue, thermal mis-match and temperature gradients. Hence, the study of failure mechanisms of TBCs become important in deciding operational reliability and service life of the coating. As there are many systems in which the operating temperatures are not high enough to warrant the use of the top coat (ceramic layer), the study of failure mechanisms in superalloys coated with only the bond coat continue to be of great interest. The present work concentrates on the fracture behavior of NiAl bond coats on nickel superalloy and seeks to evaluate the fracture toughness of the coating through the use of micro-machined samples. A review of the relevant literature indicated that while a considerable body of work exists on bulk tests of failure (spalling, splitting, etc.), not much has been reported in the open literature on the evaluation of basic quantities such as the toughness of the coating itself. The present thesis seeks to establish a protocol for the evaluation of toughness and crack propagation mechanisms in coatings through a combination of micro-sample testing that allows fracture to be correlated with location in the film and the use of an analytical model to quantitatively evaluate stress intensity factors in a bi-material system. A system of NiAl coating produced by pack aluminizing is studied for the fracture properties of the coating. Specimen geometries are optimized to enable micro-cracks to be machined and propagated in a low load testing system, such as a depth sensing indenter, so that crack lengths (and position relative to the interface) can be correlated with load. To enable linear elastic theory to be used, dimensions are determined that allow fracture before general yielding. A three point bending test using miniaturized micro-beam specimens of ~ 4 X 0.3 X 0.3 mm is found to be suitable for the above purpose. The technique is a challenging one that requires focused ion beam machining (FIB) along with careful handling and alignment of small samples. The coatings are characterized for their microstructure by electron microscopy to identify compositional variation across the thickness and to determine the thickness of the coating and inter diffusion zone (IDZ). The crack advancement is monitored with increments of loading and the stress intensity factor is evaluated using a program written in “MAPLE” for an edge crack subjected to bending in a bilayered material. Surprisingly, fracture in this system is found to be stable owing to a gradual increase in toughness from the coating surface to the interface. Such an increase from less than 2 to more than 9 MPa m0.5 may be due to the increasing Ni/Al ratio across the thickness of the bond coat. Crack branching is observed as the crack approaches the IDZ and the reasons for such behaviour are not fully understood. This work establishes the viability of this technique to determine fracture properties in highly graded coated systems and may be readily extended to more complex coating architectures and other forms of loading such as cyclic, mixed mode, etc.