<p>In this study, universal databases and semi-empirical correlations are developed for cryogenic two-phase heat transfer and pressure drop in heated tubes undergoing flow boiling.</p>

<p>This study comprises experimental investigations and theoretical/empirical analyses of three forced-convective (pumped) boiling schemes: (i) confined round single jet and jet array impingement boiling, and flow boiling through conventional-sized (ii) concentric circular annuli and (iii) rectangular channels. These schemes could be utilized in the thermal management of various applications including high-heat-flux electronic devices, power devices, electric vehicle charging cables, avionics, future space vehicles, etc.</p>

The aim ofthe study was to provideinformation and experience gained with fine wire thermocouples (TCs)or resistance wire thermometers (RWTs) temperature signals to estimate the timeresolved heat transfercoefficient. Constant current method was assumed in the study and medium used in this study was air. Here the heat balance equation has been described, different Nucorrelations and further discusses potential hurdles and difficulties one may encounter while calculating heat transfer coefficient. As asolution, the use of an appropriate heatbalance equation and lowpass filter was suggested as this provides a more accurate fitting. The investigation was carried out for Reynolds number (Re) 103 to 107 and Prandlt number (Pr) 0.734. The impact of the Re and Pr on the Nusselts number (Nu) around a cylinder was represented and all the results were compared with GT-POWER engine simulation software. / Syftet med studien var att tillhandahålla information och erfarenhet från fina trådtermoelement (TC) eller motståndstrådstermometrar (RWT) temperatursignaler för att uppskatta den tidsupplösta värmeöverföringskoefficienten. Metoden med konstant flöde antogs i studien och mediet som användes i denna studie var luft. Här har värmebalansekvationen beskrivits, olika Nu-korrelationer och diskuterat ytterligare potentiella hinder och svårigheter man kan stöta på vid beräkning av värmeöverföringskoefficienten. Som en lösning föreslogs användning av en lämplig värmebalansekvation och lågpassfilter eftersom detta ger en mer exaktpassform. Undersökningen genomfördes för Reynoldsnummer (Re) 103 till 107 och Prandlt nummer (Pr) 0,734. Effekten av Re och Pr på Nusselts-numret (Nu) runt en cylinder representerades och alla resultat jämfördes med GT-POWER-motorns simuleringsprogram.

The aim of this diploma thesis is to get acquainted with modern technological elements currently used in shell-and-tube heat exchanger in the shell-side and tube-side, thermal-hydraulic calculation of selected elements and comparison of thermal-hydraulic properties with classically used competing technological elements. The work deals mainly with EM baffle in the tube-side and tube inserts like the twisted tape type (and its modifications) and coiled wire in the tube-side. The theoretical part is focused on acquaintance with classical technological elements in shell-and-tube heat exchanger and with basic thermal-hydraulic calculations, practical part then on acquaintance with modern elements and thermal-hydraulic calculation of selected elements. These calculations are then compared with the results of the thermo-hydraulic calculation of similar elements.

The master´s thesis deals with verification of thermal insulating property of thermoreflection foil insulations. The teoretical part of thesis focuses on the energy demand of buildings, the problems of heat transfer material, terms required for study of thermoreflection thermal insulation and experimental methods for determination of thermal insulating properties of insulators. In the next part the chapter is accompanied by an overview of the most common insulation materials which used in construction. The last part of teoretical part is devoted to the description of thermoreflect formation and analysis of the spread of thermal insulating layers of thermoreflection thermal insulation. The first part of thesis is devoted to the use of thermoreflection therm insulation in buildings. The second part of thesis is devoted to the design, assembly and calibration of the measuring device that uses a method of protected warm chamber. It is declared as a binding method of detection of the heat transfer performance of thermoreflection thermal insulation. The developed measuring device allows detection of endpoints in some direction of propagation of heat. Measurment of heat transfer coefficient devoted the third part of practical part. This part contains a description of the samples used for the measurement of the heat transfer coefficient. In the fourth chapter of the practical part are presented the results of the heat transfer coefficient measurments on selected samples of thermoreflection foil insulation. It is shown the characteristic of heat transfer coefficient of individual samples, the dependence of the heat transfer coefficient on the position of the sample in the measuring device and the recommendation of an appropriate use of sample in the works for the climatic conditions of the Czech republic. The work concludes the chapter of comparing and evaluating of all samples with practical recommendations.

The task of the diploma thesis named VBA and Maple Application on Process Engineering Problems is to show the possibilities of using these programming languages for various engineering tasks. Particularly the programming language Visual Basic for Application (VBA), which is a part of MS Office package, is very little used in practise. That´s why this thesis solves the complex task of a furnaces design process; the topic was reccomended by the supervisor prof. Ing. Josef Kohoutek, CSc. Specifically, the thesis deals with calculations of heat transfer and optimization of the height of extended surfaces of tubes in the convection section of process furnaces. The entire task is elaborated in VBA and runs in Excel. After entering the input information, the created program first calculates the size and heat output of the convection section, but it can also optimize the height of extended surfaces in different parts of the convection section and thus minimize investment costs.

Master´s thesis deals with an assessment of investment return in saving precurations. The issue is used on an ordinary detached family house. The assessment is done in more variants to reach an objective comparison of the most advantageous investments. In the first part there is a comprehensive theory explaining the connections of the procedures and the algorithms of the calculations. The second part is calculation, especially from the thermal engineering, energy rating of buildings and the economic return on investment. The third part is an evaluation which, on the basis of the experiences and the results from the thesis, offers a proces show to think in case of intended reconstruction and how to evaluate the efficiency of the investments in the saving precurations.

This diploma thesis deals with the operation of radiators. It is divided into three parts. The first part describes the various types of radiators and heating surfaces, radiator control and heat measurement, the second part deals with the design of heating and hot water in an apartment building in Brno in two variants of the conceptual solution and the third part is processed in the form of experimental measurements issues of radiator operation during a real day in the heating season and operating conditions that may occur.

Injection molding is one of the most commonly applied processing methods for plastic components. Heat transfer coefficient (HTC), which describes the heat conducting ability of the interface between a polymer and cavity wall, significantly influences the temperature distribution of a polymer and mold during injection molding and thus affects the process and quality of plastic products. This thesis focuses on HTC under diverse processing situations. On the basis of the heat conducting principle, a theoretical model for calculating HTC was presented. Injection mold specially used for measuring and calculating HTC was designed and fabricated. Experimental injection studies under different processing conditions, especially different surface roughness, were performed for acquiring necessary temperature data. The heat quantity across the interface and HTC between a polymer and cavity wall was calculated on the basis of experimental results. The influence of surface roughness on HTC during injection molding was investigated for the first time. The factors influencing the HTC were analyzed on the basis of the factor weight during injection molding. Subsequently FEM (Finite element method) simulations were carried out with observed and preset value of HTC respectively and the relative crystallinity and part density were obtained. In the comparison between results from simulation and experiment, the result calculated with observed HTC shows better agreement with actually measured value, which can verify the reliability and precision of the injection molding simulation with observed HTC. The results of this thesis is beneficial for understanding the heat transfer process comprehensively, predicting temperature distribution, arranging cooling system, reducing cycle time and improving precision of numerical simulation. / Das Spritzgießen ist eines der am häufigsten angewandten Verarbeitungsverfahren zur Herstellung von Kunststoffkomponenten. Der Wärmedurchgangskoeffizient (WDK), welcher den Wärmeübergang zwischen Kunststoff und Werkzeugwand beschreibt, beeinflusst während des Spritzgießens maßgeblich die Temperaturverteilung im Bauteil und dem Werkzeug und folglich den Prozess und die Qualität der Kunststoffprodukte. Der Inhalt dieser Arbeit beschäftigt sich mit dem WDK unter verschiedenen Prozessbedingungen. Auf Grundlage des Wärmeleitungsprinzips wurde ein theoretisches Modell für die Berechnung des WDK vorgestellt. Es wurde dazu ein Spritzgießwerkzeug konstruiert und hergestellt, welches Messungen zur späteren Berechnung des WDK ermöglicht. Praktische Spritzgießversuche unter verschiedenen Prozessbedingungen, insbesondere unterschiedlicher Oberflächenrauheit, wurden für die Erfassung der erforderlichen Temperaturdaten durchgeführt. Auf Grundlage der experimentellen Ergebnisse wurde der Wärmeübergang zwischen dem Polymer und der Werkzeugwand berechnet. Der Einfluss der Oberflächenrauhigkeit auf den WDK wurde hierbei zum ersten Mal untersucht. Auf Grundlage des Bauteilgewichtes wurden anschließend die Faktoren, die den WDK beeinflussen, berechnet. Des Weiteren wurden FEM-Simulationen (Finite Element Methode) mit dem gemessenen und dem voreingestellten WDK durchgeführt und daraus der Kristallinitätsgrad und die Bauteildichte gewonnen. Der Vergleich zwischen den realen Ergebnissen und der Simulation zeigt, dass die Berechnungen mit dem gemessenen WDK eine bessere Übereinstimmung mit den realen Werten aufweist, was die Zuverlässigkeit und Präzision der Spritzgusssimulation bestätigt. Die Ergebnisse dieser Arbeit tragen zum umfassenden Verständnis des Wärmeübergangs im Spritzgießprozess, zur Vorhersage der Temperaturverteilung, zur Auslegung des Kühlsystems, zur Reduzierung der Zykluszeit und zur Verbesserung der Genauigkeit der numerischen Simulation bei.

Diploma thesis focuses on effect of the bypass factor on design and geometry of the evaporator for the cooling unit of data centre. Effect of the bypass factor on individual design parameters is solved in detail. All dependendecies are captured by using graphs in which s placed a cement on that parameter. In part C, mathematical and physical solutions are demonstrated calculations and processes leading to the design of the exchanger. In the end, evaluation of the calculations is done and there is also showed possible improvements for the practise.