The use of variable frequency drives in centrifugal pump applications has raised the question of how to select a drive. Clogging obstacles in waste water applications create unknown transient loads for the pump system. A sudden load increase occurrence can clog the pump if the drive cannot supply enough current to reach the motor’s torque demand. In order to select a suitable drive, an empirical approach has been implemented, investigating three different drives. Results have shown that selecting a drive with the highest possible overload capabilities, even if for a short time is most suitable. Operation in vector speed control gives the most reliable operation if an automatic parameter tuning is performed by the drive. / Användningen av frekvensomriktare i centrifugalpumpar har väckt fr ågan om hur en omriktare skall väljas. Igensättande objekt i avloppsvatten kan ge upphov till transienta laster i pumpsystemen. En oförutsedd lastökning kan sätta igen pumpen om frekvensomriktaren inte kan förse motorn tillräckligt med ström för att möta momentbehovet. För att välja en lämplig omriktare har ett empiriskt tillvägag ångssätt valts i en undersökning av tre olika omriktare. Resultat har visat att det är lämpligast att välja en omriktare med högst överbelastningskapacitet, även om under en kort tid. Vektor hastighetskontroll är metoden som ger stabil körning om omriktaren f ått automatiskt ställa in motorparametrarna.

Cavity ring-down spectroscopy has been used over the last twenty years as a highly sensitive absorption spectroscopic technique to measure light attenuation in gases, liquids, and solid samples. An optical cavity is used as a multi-pass cell, and the decay time of the light intensity in the cavity is measured, thereby rendering the techniques insensitive to light intensity fluctuations. Optical waveguides are used to build the optical cavities presented in this work. The geometries of such waveguides permit the use of very small liquid sample volumes while retaining the advantages of cavity ring-down spectroscopy. In this thesis cavity ring-down measurements are conducted, both, in the time domain and by measuring phase-shifts of sinusoidally modulated light, and the two methods are theoretically connected using a simple mathematical model, which is then experimentally confirmed. A new laser driver, that is compatible with high powered diode lasers, has to be designed to be able to switch from time domain to frequency domain measurements. A sample path length enhancement within the optical cavity is explored with the use of liquid core waveguides. The setup was optimised with respect to the matrix liquid, the geometrical matching of waveguide geometries, and the shape of liquid core waveguide ends. Additionally, a new technique of producing concave lenses at fibre ends has been developed and the output of a general fibre lens is simulated. Finally, liquid core waveguides are incorporated into a fibre-loop ring-down spectroscopy setup to measure the attenuation of two model dyes in a sample volume of <1 µL. The setup is characterized by measuring concentrations of Allura Red AC and Congo Red from 1 µM to a limit of detection of 5 nM. The performance of the setup is compared to other absorption techniques measuring liquid samples. / Thesis (Ph.D, Chemistry) -- Queen's University, 2013-04-23 14:08:16.33

The development of a numeric simulation for predicting the performance of an Ocean Current Energy Conversion System is presented in this thesis along with a control system development using a PID controller for the achievement of specified rotational velocity set-points. In the beginning, this numeric model is implemented in MATLAB/Simulink® and it is used to predict the performance of a three phase squirrel single-cage type induction motor/generator in two different cases. The first case is a small 3 meter rotor diameter, 20 kW ocean current turbine with fixed pitch blades, and the second case a 20 meter, 720 kW ocean current turbine with variable pitch blades. Furthermore, the second case is also used for the development of a Voltage Source Variable Frequency Drive for the induction motor/generator. Comparison among the Variable Frequency Drive and a simplified model is applied. Finally, the simulation is also used to estimate the average electric power generation from the 720 kW Ocean Current Energy Conversion System which consists of an induction generator and an ocean current turbine connected with a shaft which modeled as a mechanical vibration system.

This thesis deals with the design of Hybrid Energy Storage System (HESS) for Light Electric Vehicles (LEV) and EVs. More specifically, a tri-mode high-efficiency non-isolated half-bridge converter is developed for the LEV based HESS applications. A 2 kW, 100 V interleaved two-phase converter prototype was implemented. The peak efficiency of 97.5% and a minimum efficiency of 88% over the full load range are achieved. Furthermore, a power-mix optimizer utilizing the real-time Global Positioning System (GPS) data for the EV based HESS is proposed. For a specific design, it is shown that at the cost of less than 1.5% of the overall energy savings, the proposed scheme reduces the peak battery charge and discharge rates by 76% and 47%, respectively. A 30 kW bi-directional dc-dc converter is also designed and implemented for future deployment of the designed HESS into a prototype EV, known as A2B.

This thesis deals with the design of Hybrid Energy Storage System (HESS) for Light Electric Vehicles (LEV) and EVs. More specifically, a tri-mode high-efficiency non-isolated half-bridge converter is developed for the LEV based HESS applications. A 2 kW, 100 V interleaved two-phase converter prototype was implemented. The peak efficiency of 97.5% and a minimum efficiency of 88% over the full load range are achieved. Furthermore, a power-mix optimizer utilizing the real-time Global Positioning System (GPS) data for the EV based HESS is proposed. For a specific design, it is shown that at the cost of less than 1.5% of the overall energy savings, the proposed scheme reduces the peak battery charge and discharge rates by 76% and 47%, respectively. A 30 kW bi-directional dc-dc converter is also designed and implemented for future deployment of the designed HESS into a prototype EV, known as A2B.