Interactive handheld electronic displays use hydrogenated amorphous silicon (a-Si:H) thin film transistor (TFT) as a backplane and a Touch Screen Panel (TSP) on top as an input device. The low mobility and instability of a-Si:H TFT threshold voltage are major two issues for driving constant current as required for Active Matrix Organic Light Emitting Ddiode (AMOLED) displays. Low mobility is compensated by increasing transistor width or resorting to more expensive material TFTs. On the other hand, the ever increasing threshold voltage shift degrades the drain current under electrical operation causing OLED display to dim. Mutual capacitive TSP, the current cell phone standard, requires two layers of metals and a dielectric to be put in front of the display, further dimming the device and adding to visual noise due to sun reflection, not to mention increased integration cost and decreased yield. This thesis focuses on the aforementioned technological hurdles of a handheld electronic display by proposing a dual-gate TFT used as an OLED current driving TFT and a novel phase response readout scheme that can be applied to a one metal track TSP. Our dual-gate TFT has shown on average 20% increase in drive current over a single gate TFT fabricated in the same batch, attributed to the aid of a top channel to the convention bottom channel TFT. Furthermore the dual gate TFT shows three times the Poole-Frenkel current than the single gate TFT attributed to the increase in gate to drain overlap. The dual-gate TFT shows a 50% improvement in threshold voltage shift over a single gate TFT at room temperature, but only ~8% improvement under 75ºC. This is an important observation as it shows an accelerated threshold voltage shift in the dual-gate. This difference in the rate of threshold voltage change under varying temperature is attributed to the difference in interface states, supporting Libsch and Kanicki’s multi-level temperature dependant dielectric trapping model. The phase response TSP readout scheme requires IC only on one side of the display. Cadence Spectre simulation results showed that both touch occurrence and touch position can be obtained using only one metal layer.

Interactive handheld electronic displays use hydrogenated amorphous silicon (a-Si:H) thin film transistor (TFT) as a backplane and a Touch Screen Panel (TSP) on top as an input device. The low mobility and instability of a-Si:H TFT threshold voltage are major two issues for driving constant current as required for Active Matrix Organic Light Emitting Ddiode (AMOLED) displays. Low mobility is compensated by increasing transistor width or resorting to more expensive material TFTs. On the other hand, the ever increasing threshold voltage shift degrades the drain current under electrical operation causing OLED display to dim. Mutual capacitive TSP, the current cell phone standard, requires two layers of metals and a dielectric to be put in front of the display, further dimming the device and adding to visual noise due to sun reflection, not to mention increased integration cost and decreased yield. This thesis focuses on the aforementioned technological hurdles of a handheld electronic display by proposing a dual-gate TFT used as an OLED current driving TFT and a novel phase response readout scheme that can be applied to a one metal track TSP. Our dual-gate TFT has shown on average 20% increase in drive current over a single gate TFT fabricated in the same batch, attributed to the aid of a top channel to the convention bottom channel TFT. Furthermore the dual gate TFT shows three times the Poole-Frenkel current than the single gate TFT attributed to the increase in gate to drain overlap. The dual-gate TFT shows a 50% improvement in threshold voltage shift over a single gate TFT at room temperature, but only ~8% improvement under 75ºC. This is an important observation as it shows an accelerated threshold voltage shift in the dual-gate. This difference in the rate of threshold voltage change under varying temperature is attributed to the difference in interface states, supporting Libsch and Kanicki’s multi-level temperature dependant dielectric trapping model. The phase response TSP readout scheme requires IC only on one side of the display. Cadence Spectre simulation results showed that both touch occurrence and touch position can be obtained using only one metal layer.

Thin Film Transistors (TFTs) are widely used in large area electronics because they offer the advantage of low cost fabrication and wide substrate choice. TFTs have been conventionally used for switching applications in large area display arrays. But when it comes to designing a sensor actuator system on a flexible substrate comprising entirely of organic and inorganic TFTs, there are two main challenges – i) Fabrication of complementary TFT devices is difficult ii) TFTs have a drift in their threshold voltage (VT) on application of gate bias. Also currently there are no circuit simulators in the market which account for the effect of VT drift with time in TFT circuits. The first part of this thesis focuses on integrating the VT shift model in the commercially available AIM-Spice circuit simulator. This provides a new and powerful tool that would predict the effect of VT shift on nodal voltages and currents in circuits and also on parameters like small signal gain, bandwidth, hysteresis etc. Since the existing amorphous silicon TFT models (level 11 and level 15) of AIM-Spice are copyright protected, the open source BSIM4V4 model for the purpose of demonstration is used. The simulator is discussed in detail and an algorithm for integration is provided which is then supported by the data from the simulation plots and experimental results for popular TFT configurations. The second part of the thesis illustrates the idea of using negative feedback achieved via contact resistance modulation to minimize the effect of VT shift in the drain current of the TFT. Analytical expressions are derived for the exact value of resistance needed to compensate for the VT shift entirely. Circuit to realize this resistance using TFTs is also provided. All these are experimentally verified using fabricated organic P-type Copper Phthalocyanine (CuPc) and inorganic N-type Tin doped Zinc Oxide (ZTO) TFTs. The third part of the thesis focuses on building a robust amplifier using these TFTs which has time invariant DC voltage level and small signal gain at the output. A differential amplifier using ZTO TFTs has been built and is shown to fit all these criteria. Ideas on vertical routing in an actual sensor actuator interface using this amplifier have also been discussed such that the whole system may be “tearable” in any contour. Such a sensor actuator interface can have varied applications including wrap around thermometers and X-ray machines.