No description available.

In this thesis, design aspects of fully integrated multibandmultistandard front-end receivers are investigated based onthree fundamental aspects: noise, linearity and operatingfrequency. System level studies were carried out to investigatethe effects of different modulation techniques, duplexing andmultiple access methods on the noise, linearity and selectivityperformance of the circuit. Based on these studies and thelow-cost consideration, zero-IF, low-IF and wideband-IFreceiver architectures are promising architectures. These havea common circuit topology in a direct connection between theLNA and the mixer, which has been explored in this work toimprove the overall RF-to-IF linearity. One front-end circuitapproach is used to achieve a low-cost solution, leading to anew multiband multistandard front-end receiver architecture.This architecture needs a circuit whose performance isadaptable due to different requirements specified in differentstandards, works across several RF-bands and uses a minimumamount ofexternal components. Five new circuit topologies suitable for a front-endreceiver consisting of an LNA and mixer (low-noise converter orLNC) were developed. A dual-loop wide-band feedback techniquewas applied in all circuits investigated in this thesis. Threeof the circuits were implemented in 0.18 mm RF-CMOS and 25 GHzbipolar technologies. Measurement results of the circuitsconfirmed the correctness of the design approach. The circuits were measured in several RF-bands, i.e. in the900 MHz, 1.8 GHz and 2.4 GHz bands, with S11 ranging from–9.2 dB to–17 dB. The circuits have a typicalperformance of 18-20 dB RF-to-IF gain, 3.5-4 dB DSB NF and upto +4.5 dBm IIP3. In addition, the circuit performance can beadjusted by varying the circuit’s first-stage biascurrent. The circuits may work at frequencies higher than 3GHz, as only 1.5 dB of attenuation is found at 3 GHz and nopeaking is noticed. In the CMOS circuit, the extrapolated gainat 5 GHz is about 15 dB which is consistent with the simulationresult. The die-area of each of the circuits is less than 1mm2.

This work consists of two main parts: a) Design of a 3-10GHz UltraWideBand (UWB) Receiver and b) Built-In Testing Techniques (BIT) for Analog and RF circuits. The MultiBand OFDM (MB-OFDM) proposal for UWB communications has received significant attention for the implementation of very high data rate (up to 480Mb/s) wireless devices. A wideband LNA with a tunable notch filter, a downconversion quadrature mixer, and the overall radio system-level design are proposed for an 11-band 3.4-10.3GHz direct conversion receiver for MB-OFDM UWB implemented in a 0.25mm BiCMOS process. The packaged IC includes an RF front-end with interference rejection at 5.25GHz, a frequency synthesizer generating 11 carrier tones in quadrature with fast hopping, and a linear phase baseband section with 42dB of gain programmability. The receiver IC mounted on a FR-4 substrate provides a maximum gain of 67-78dB and NF of 5-10dB across all bands while consuming 114mA from a 2.5V supply. Two BIT techniques for analog and RF circuits are developed. The goal is to reduce the test cost by reducing the use of analog instrumentation. An integrated frequency response characterization system with a digital interface is proposed to test the magnitude and phase responses at different nodes of an analog circuit. A complete prototype in CMOS 0.35mm technology employs only 0.3mm2 of area. Its operation is demonstrated by performing frequency response measurements in a range of 1 to 130MHz on 2 analog filters integrated on the same chip. A very compact CMOS RF RMS Detector and a methodology for its use in the built-in measurement of the gain and 1dB compression point of RF circuits are proposed to address the problem of on-chip testing at RF frequencies. The proposed device generates a DC voltage proportional to the RMS voltage amplitude of an RF signal. A design in CMOS 0.35mm technology presents and input capacitance <15fF and occupies and area of 0.03mm2. The application of these two techniques in combination with a loop-back test architecture significantly enhances the testability of a wireless transceiver system.

<p>In this thesis, design aspects of fully integrated multibandmultistandard front-end receivers are investigated based onthree fundamental aspects: noise, linearity and operatingfrequency. System level studies were carried out to investigatethe effects of different modulation techniques, duplexing andmultiple access methods on the noise, linearity and selectivityperformance of the circuit. Based on these studies and thelow-cost consideration, zero-IF, low-IF and wideband-IFreceiver architectures are promising architectures. These havea common circuit topology in a direct connection between theLNA and the mixer, which has been explored in this work toimprove the overall RF-to-IF linearity. One front-end circuitapproach is used to achieve a low-cost solution, leading to anew multiband multistandard front-end receiver architecture.This architecture needs a circuit whose performance isadaptable due to different requirements specified in differentstandards, works across several RF-bands and uses a minimumamount ofexternal components.</p><p>Five new circuit topologies suitable for a front-endreceiver consisting of an LNA and mixer (low-noise converter orLNC) were developed. A dual-loop wide-band feedback techniquewas applied in all circuits investigated in this thesis. Threeof the circuits were implemented in 0.18 mm RF-CMOS and 25 GHzbipolar technologies. Measurement results of the circuitsconfirmed the correctness of the design approach.</p><p>The circuits were measured in several RF-bands, i.e. in the900 MHz, 1.8 GHz and 2.4 GHz bands, with S11 ranging from–9.2 dB to–17 dB. The circuits have a typicalperformance of 18-20 dB RF-to-IF gain, 3.5-4 dB DSB NF and upto +4.5 dBm IIP3. In addition, the circuit performance can beadjusted by varying the circuit’s first-stage biascurrent. The circuits may work at frequencies higher than 3GHz, as only 1.5 dB of attenuation is found at 3 GHz and nopeaking is noticed. In the CMOS circuit, the extrapolated gainat 5 GHz is about 15 dB which is consistent with the simulationresult. The die-area of each of the circuits is less than 1mm2.</p>

Three new and efficient carrier frequency offset estimators are created for the case of disjoint pilot symbol blocks. The estimators are efficient in both a statistical sense and a computational sense. They are formulated to reduce computational cost for use in real-time applications, such as FPGA (field programmable gate array) devices. A reduced cost maximum likelihood (ML) frequency estimator is described. It is a generalization of the approximate ML estimator for a single block of pilot symbols. A number of recent ML estimation techniques are integrated with the purpose of reducing the computational cost while preserving estimation performance. The estimator incorporates multirate signal processing methods, FFT periodogram searches, and directed periodogram searches. The subsequent relationships between FFT lengths, resampling rates, and search iterations is established. The proposed estimator exhibits very good accuracy, operating range, and a low SNR threshold, and has low cost. A data-aided frequency estimator based on the measurement of phase increments, is also derived. It has extremely low cost, but a high SNR threshold. However, its formulation is such that a careful analysis of the range error problem may be performed. From this analysis certain conclusions are made about proper pilot symbol organization, and these conclusions are applicable to other frequency estimators. The third estimator is a generalization of the autocorrelation frequency estimation technique. The generalizations are needed to account for the spacings between the pilot blocks. A novel iterative approach, incorporating a Kalman filter, is used to improve operating range. It is shown that the autocorrelation frequency estimator exhibits good accuracy while maintaining a useful operating range. Real-time architectures are described for the ML and autocorrelation frequency estimators using disjoint pilot blocks. The computational cost and estimation performance of the proposed estimators are analyzed and it is shown that they give estimation performance near to theoretical limits, while preserving wide operating range. We see that the autocorrelation estimator is appropriate for small numbers of pilot symbols, while the ML estimator is appropriate for large numbers of pilot symbols. The new frequency estimators are the first to be derived (for the case of disjoint blocks of pilot symbols) such that computational cost is kept low, while still achieving high accuracy, a wide operating range, and low SNR thresholds.

Data transfer rates of communication systems continue to rise fueled by aggressive demand for voice, video and Internet data. Device scaling enabled by modern lithography has paved way for System-on-Chip solutions integrating compute intensive digital signal processing. This trend coupled with demand for low power, battery-operated consumer devices offers extensive research opportunities in analog and mixed-signal designs that enable modern communication systems. The first part of the research deals with broadband wireless receivers. With an objective to gain insight, we quantify the impact of undesired out-band blockers on analog baseband in a broadband radio. We present a systematic evaluation of the dynamic range requirements at the baseband and A/D conversion boundary. A prototype UHF receiver designed using RFCMOS 0.18[mu]m technology to support this research integrates a hybrid continuous- and discrete-time analog baseband along with the RF front-end. The chip consumes 120mW from a 1.8V/2.5V dual supply and achieves a noise figure of 7.9dB, an IIP3 of -8dBm (+2dbm) at maximum gain (at 9dB RF attenuation). High linearity active RC filters are indispensable in wireless radios. A novel feed-forward OTA applicable to active RC filters in analog baseband is presented. Simulation results from the chip prototype designed in RFCMOS 0.18[mu]m technology show an improvement in the out-band linearity performance that translates to increased dynamic range in the presence of strong adjacent blockers. The second part of the research presents an adaptive clock-recovery system suitable for high-speed wireline transceivers. The main objective is to improve the jitter-tracking and jitter-filtering trade-off in serial link clock-recovery applications. A digital state-machine that enables the proposed mixed-signal adaptation solution to achieve this objective is presented. The advantages of the proposed mixed-signal solution operating at 10Gb/s are supported by experimental results from the prototype in RFCMOS 0.18[mu]m technology.

CDMA channel selection requires sharp as well as wide-band Filtering. SAW Filters which have been used for this purpose are only available in IF range. In direct conversion receivers this has to be done at low frequencies. Switched Capacitor technique has been employed to design a low power, highly selective low-pass channel select Filter for CDMA wireless receivers. The topology which has been chosen ensures the low sensitivity of the Filter response. The circuit has been designed in a mixed-mode 0. 18u CMOS technology working with a single supply of 1. 8 V while its current consumption is less than 10 mA.

CDMA channel selection requires sharp as well as wide-band Filtering. SAW Filters which have been used for this purpose are only available in IF range. In direct conversion receivers this has to be done at low frequencies. Switched Capacitor technique has been employed to design a low power, highly selective low-pass channel select Filter for CDMA wireless receivers. The topology which has been chosen ensures the low sensitivity of the Filter response. The circuit has been designed in a mixed-mode 0. 18u CMOS technology working with a single supply of 1. 8 V while its current consumption is less than 10 mA.

As one of the major building blocks in a wireless receiver, the Analog-to-Digital Interface (ADI) provides link and transition between the analog Radio Frequency (RF) frontend and the baseband Digital Signal Processing (DSP) module. The rapid development of the radio technologies raises new design challenges for the receiver ADI implementation. Requirements, such as power consumption optimization, multi-standard compatibility, fast settling capability and wide signal bandwidth capacity, are often encountered in a low voltage ADI design environment. Previous research offers ADI design schemes that emphasize individual merit. A systematic ADI design methodology is, however, not suffciently studied. In this work, the ADI design for two receiver systems are employed as research vehicles to provide solutions for different ADI design issues. A zero-crossing demodulator ADI is designed in the 0.35µm CMOS technology for the Bluetooth receiver to provide fast settling. Architectural level modi&#64257;cation improves the process variation and the Local Oscillation (LO) frequency offset immunity of the demodulator. A 16.2dB Signal-to-Noise Ratio (SNR) at 0.1% Bit Error Rate (BER) is achieved with less than 9mW power dissipation in the lab measurement. For ADI in the 802.11b/Bluetooth dual-mode receiver, a con&#64257;gurable time-interleaved pipeline Analog-to-Digital-Converter (ADC) structure is adopted to provide the required multi-standard compatibility. An online digital calibration scheme is also proposed to compensate process variation and mismatching. The prototype chip is fabricated in the 0.25µm BiCMOS technology. Experimentally, an SNR of 60dB and 64dB are obtained under the 802.11b and Bluetooth receiving modes, respectively. The power consumption of the ADI is 20.2mW under the 802.11b receiving mode and 14.8mW under the Bluetooth mode. In this dissertation, each step of the receiver ADI design procedure, from system level optimization to the transistor level implementation and lab measurement, is illustrated in detail. The observations are carefully studied to provide insight on receiver ADI design issues. The ADI design for the Ultra-Wide Band (UWB) receiver is also studied at system level. Potential ADI structure is proposed to satisfy the wide signal bandwidth and high speed requirement for future applications.

Receiver design, especially equalizer design, in communications is a major concern in both academia and industry. It is a problem with both theoretical challenges and severe implementation hurdles. While much research has been focused on reducing complexity for optimal or near-optimal schemes, it is still common practice in industry to use simple techniques (such as linear equalization) that are generally significantly inferior. Although digital signal processing (DSP) technologies have been applied to wireless communications to enhance the throughput, the users' demands for more data and higher rate have revealed new challenges. For example, to collect the diversity and combat fading channels, in addition to the transmitter designs that enable the diversity, we also require the receiver to be able to collect the prepared diversity. Most wireless transmissions can be modeled as a linear block transmission system. Given a linear block transmission model assumption, maximum likelihood equalizers (MLEs) or near-ML decoders have been adopted at the receiver to collect diversity which is an important metric for performance, but these decoders exhibit high complexity. To reduce the decoding complexity, low-complexity equalizers, such as linear equalizers (LEs) and decision feedback equalizers (DFEs) are often adopted. These methods, however, may not utilize the diversity enabled by the transmitter and as a result have degraded performance compared to MLEs. In this dissertation, we will present efficient receiver designs that achieve low bit-error-rate (BER), high mutual information, and low decoding complexity. Our approach is to first investigate the error performance and mutual information of existing low-complexity equalizers to reveal the fundamental condition to achieve full diversity with LEs. We show that the fundamental condition for LEs to collect the same (outage) diversity as MLE is that the channels need to be constrained within a certain distance from orthogonality. The orthogonality deficiency (od) is adopted to quantify the distance of channels to orthogonality while other existing metrics are also introduced and compared. To meet the fundamental condition and achieve full diversity, a hybrid equalizer framework is proposed. The performance-complexity trade-off of hybrid equalizers is quantified by deriving the distribution of od. Another approach is to apply lattice reduction (LR) techniques to improve the ``quality' of channel matrices. We present two widely adopted LR methods in wireless communications, the Lenstra-Lenstra-Lovasz (LLL) algorithm [51] and Seysen's algorithm (SA), by providing detailed descriptions and pseudo codes. The properties of output matrices of the LLL algorithm and SA are also quantified. Furthermore, other LR algorithms are also briefly introduced. After introducing LR algorithms, we show how to adopt them into the wireless communication decoding process by presenting LR-aided hard-output detectors and LR-aided soft-output detectors for coded systems, respectively. We also analyze the performance of proposed efficient receivers from the perspective of diversity, mutual information, and complexity. We prove that LR techniques help to restore the diversity of low-complexity equalizers without increasing the complexity significantly. When it comes to practical systems and simulation tool, e.g., MATLAB, only finite bits are adopted to represent numbers. Therefore, we revisit the diversity analysis for finite-bit represented systems. We illustrate that the diversity of MLE for systems with finite-bit representation is determined by the number of non-vanishing eigenvalues. It is also shown that although theoretically LR-aided detectors collect the same diversity as MLE in the real/complex field, it may show different diversity orders when finite-bit representation exists. Finally, the VLSI implementation of the complex LLL algorithms is provided to verify the practicality of our proposed designs.