Rapportens huvudsyfte är att ta fram en isoleringskombination av högpresterande material, som ska bidra till ett förbättrat U-värde och reducerad väggtjocklek. Konstruktionen är baserad på en befintlig sandwichvägg från Strängbetong, där författarna ersatt den ursprungliga isoleringen med det utvecklade isolerskiktet för att slutligen studera väggarna med lika villkor. Den framtagna väggens isolerings- förmåga presenteras genom handberäkningar, där det erhålls U-värde och temperaturfördelningar mellan elementens olika skikt vid stationära förhållanden. Det har även utförts värmesimuleringar för att analysera samma fysikaliska faktorer dock baserat på 3D förhållanden. I samarbete med företag har flera högpresterande isoleringsmaterial valts ut att ingå i väggkonstruktionen. Genom fördjupade studier av materialens fysikaliska egenskaper kunde en komplett isoleringskombination utvecklas och fick namnet InsuFlex. InsuFlex applicerades sedan i en sandwichkonstruktion för vidare analyser och värmesimuleringar. De nya väggresultaten visade mycket goda förbättringar av den ursprungliga sandwichväggen, tack vare det utvecklade skiktet av InsuFlex. Genom utförda beräkningar kunde författarna konstatera att isoleringsförmågan förbättrats med 46,5- samt 29 %, samtidigt som tjockleken reducerats med 5,5- samt 16,5 %, i jämförelse med Strängbetongs befintliga produkt. Den nya väggen erbjuder goda förutsättningar att reducera energiförlusterna och komma närmare framtida energikrav. Isoleringsmetoden förväntas även kunna appliceras i flera olika konstruktionselement. / The main objective of this report is development of an insulation-layer of high performance materials for a sandwich structure, which will contribute to an improved U-value and reduced wall thickness. The design is based on an existing sandwich wall, where the authors replaced the original insulation with the developed insulation-layer, to study the walls with equal conditions. The insulating ability is presented through calculations and thermal simulation to analyze the thermal aspects of the stationary conditions and 3D conditions. A complete insulation combination was developed through extensive studies of material’s physical properties, and named “InsuFlex”. The insulation-layer was then applied in a sandwich construction for further analysis and thermal simulations. The new design showed improvements in several areas.

La nanotechnologie est devenue un domaine clé de la technologie du XXIe siècle. L’important développement des approches pour la synthèse des nanoparticules (NPs) avec une composition, une taille et une forme désirées rend compte du potentiel de leur utilisation comme « blocs de construction » pour des structures de plus grande échelle. Cela permet d’envisager à la fois la fabrication de matériaux fonctionnels et de dispositifs directement à partir de colloïdes par approche ascendante et la conception de matériaux sur plusieurs échelles de grandeur. Le procédé utilise l'assemblage ou l'auto-assemblage de NPs et conduit à des matériaux avec des architectures différentes notamment 1D (bâtonnets), 2D (films) ou 3D (super-réseaux ou gels). Cependant, la plupart des assemblages 3D sont limités à l'échelle micrométrique et sont difficiles à contrôler. Pratiquement, la seule voie permettant la préparation de structures 3D macroscopiques à partir de NPs est la gélification et la préparation d'aérogels. Une voie alternative consiste à disperser les NPs dans une matrice, conduisant ainsi à un matériau composite massif, avec des NPs non agrégées distribuées de manière homogène.Le présent travail est consacré au développement de matériaux à partir de NPs d'oxydes métalliques (principalement Y3Al5O12: Ce et Li4Ti5O12) de différentes dimensions et pour diverses applications. La première partie de ce travail décrit la synthèse de NPs de YAG: Ce et de LTO par approche glycothermale. Dans le cas du YAG: Ce, les conditions de réaction ont été ajustées de façon appropriée pour obtenir des nanocristaux (NCs) non agrégés de quelques nanomètres. Des solutions colloïdales de différentes concentrations contenant de tels NCs ont été utilisées, pour la fabrication par la technique de « spin-coating », de films minces avec une épaisseur contrôlable. A l’inverse, la synthèse de LTO conduit à des NPs agrégées dans une structure hiérarchique très bénéfique pour les batteries au lithium. La grande surface spécifique et la porosité du matériau obtenu assurent en effet un échange efficace des ions lithium entre l'électrolyte et le matériau d'anode.Par ailleurs, les NCs de YAG: Ce ont été utilisés pour la préparation de matériaux monolithiques de grande taille avec une porosité et une transparence élevées. Pour cela, la solution colloïdale de NCs a été gélifiée par le changement brusque de la constante diélectrique du solvant de dispersion des NCs. Les gels ainsi obtenus ont été par la suite séchés de manière supercritique, donnant ainsi des aérogels à base de NPs de YAG:Ce, avec une porosité et une transparence élevées. La même approche s'est avérée appropriée pour d'autres systèmes à base de NPs de GdF3 ou de mélanges de NPS de YAG: Ce et de GdF3.Alternativement, les NPs de YAG: Ce ont été incorporées dans des aérogels de silice formant ainsi des aérogels macroscopiques robustes et hautement transparents présentant les propriétés des NPs incorporées. Ces aérogels composites ont été utilisés en tant que nouveaux types de capteurs pour les rayonnements ionisants de basse énergie dans les liquides ou les gaz. Leur porosité élevée permet un contact optimal entre l'émetteur radioactif et le scintillateur assurant ainsi une bonne récupération de l'énergie radioactive. / Nanotechnology has become a key domain of technology in XXI century. The great development of the synthetic approaches toward nanoparticles (NPs) with desired composition, size and shape expose the potential of their use as building blocks for larger scale structures. It allows fabrication of functional materials and devices directly from colloids by bottom-up approach, thus involving possibility of material design over several length scales. The process is referred to NPs assembly or self-assembly and leads to materials with varying architectures as for instance 1D (rods), 2D (films) or 3D (superlattices or gels). However most of 3D assemblies are limited to the micrometric scale and are difficult to control. Practically the only route allowing preparation of macroscopic 3D structures from NPs is their gelation and preparation of aerogels. As an alternative, NPs can be embedded in some matrix creating bulk composite material, with homogenously distributed non-aggregated NPs.Therefore, this work is devoted to development of materials with different dimensionalities for various applications from metal oxides NPs (mainly Y3Al5O12:Ce and Li4Ti5O12). The first part describes the syntheses of YAG:Ce and LTO NPs by glycothermal approach. In the case of YAG:Ce, the reactions conditions were appropriately adjusted in order to obtain non-aggregated nanocrystals (NCs) of few nanometers. The colloidal solution containing such NCs with different concentration was used for fabrication of thin films with controllable thickness by spin-coating method. Contrary, the synthesis of LTO led to aggregated NPs with hierarchical structuration which was highly beneficial for Li-ion batteries. The large surface area and porosity ensured efficient exchange of Li ions between electrolyte and anode material. Furthermore, the YAG:Ce NCs were used for preparation of macroscopic monoliths with high porosity and transparency. For that reason, colloidal solution of NCs was gelled by the abrupt change of solvent dielectric constant. The gels were further supercritically dried yielding YAG:Ce NPs-based aerogels with high porosity and transparency. The same approach turned o be appropriate for other systems like GdF3 or hybrid aerogels of YAG:Ce and GdF3.Alternatively, YAG:Ce NPs were incorporated into silica aerogels forming robust macroscopic and highly transparent aerogels exhibiting properties of incorporated NPs. They served for novel type of sensors for low-energy ionizing radiation in liquids and gases. Their high porosity assured well-developed contact between radioactive emitter and the scintillator ensuring good harvesting of radioactive energy.

Cette thèse présente un travail sur l’obtention d’aérogels d’HDL par séchage en conditions CO2 supercritique et l’élaboration de nouveaux bionanocomposites formés par la coprécipitation d’hydroxydes doubles lamellaire (HDL) dans l'espace confiné des billes d'alginate. Grâce à la combinaison d’une synthèse par coprécipitation Flash et d’un séchage en conditions supercritiques au CO2, des aérogels d’HDL possédant des surfaces spécifiques élevées sont élaborés. Parallèlement, l’alginate est utilisé comme une matrice de confinement pour la précipitation inorganique d’HDL. D’une part, les billes d'alginate sont synthétisées par complexation des ions Ca2+ et la coprécipitation des phases HDL s’effectue en réalisant des imprégnations successives de réactifs. D’autre part, des billes d'alginate sont formées directement en présence des cations divalents (Mg2+, Ni2++, Co2+, ...) et des cations des métaux trivalents (Al3+), précurseurs des composés inorganiques. La coprécipitation des HDL se produit dans ce cas lors d'une étape d'imprégnation dans une solution d'hydroxyde de sodium. Tous les composés HDL, aérogels ou encore bionanocomposites sont caractérisés en détail par DRX, spectroscopie IR, MEB/MET, adsorption/désorption d’azote et ATG/DTG, pour obtenir un meilleur aperçu de la structure des particules, de leur taille et de leur morphologie. Des études menées sur l’adsorption de la trypsine pour les aérogels ou encore sur les performances d’électrodes modifiées HDL-alginate ont permis de montrer qu’il était possible d'améliorer les performances des HDL en augmenter leur porosité et en élaborant des bionanocomposites. / In this work, we investigated both the use of CO2 supercritical drying conditions and the use of biopolymer to modify the growth and aggregation of inorganic Layered Double Hydroxide (LDH) particles. Indeed, one possibility to enhance their performances is to increase the LDH porosity and to design them as nanostructured open structure. Thanks to the combinaison of fast coprecipitation and CO2 supercritical drying, highly porous LDH aerogels were obtained with enhanced textural properties. In parallel, the coprecipitation of Layered Double Hydroxides (LDH) in the confined space of alginate beads is reported. In our approach, Alginate acts as a template to support and confined the inorganic precipitation. In one hand, beads made of Alginate are synthesized by complexation of Ca2+ ions and LDH phases are coprecipitated using successive impregnations of reactants. In another hand, Alginate beads are formed directly in presence of the divalent (Mg2+, Ni2+, Co2+,…) and trivalent metal cations (Al3+), precursors of the inorganic compounds. LDH coprecipitation then occurs during a further impregnation step in a sodium hydroxide solution. All the LDH aerogels and LDH nanocomposites beads are deeply characterized using XRD, SEM/TEM, FTIR spectroscopic, adsorption/desorption of nitrogen and TGA/DTG to get better insight on particle structure, size and morphology Aerogels display enhanced adsorption behavior toward trypsine immobilization whereas a net improvement of the electrochemical response is noticed for the NiAl based bionanocomposites prepared by confined coprecipitation into Alginate.

Cette thèse s'intéresse à la préparation, par la technique de la lyophilisation, des aérogelsà base de celluloses et de charges minérales destinés à une utilisation potentielle dans le domainede l'isolation thermique. Le premier objectif de la thèse a été la caractérisation de différentescelluloses (cellulose (PBPD), nanocristaux (NCC) et nanofibrilles oxydées (NFCs)), les chargesminérales (principalement la zéolithe) et les différents aérogels résultants de différentescombinaisons des matériaux de départ utilisés. Nous avons utilisé pour la caractérisation desmatériaux de départ et des aérogels des techniques d'analyse telles que la diffraction des rayonsX (DRX), la BET, le MEB et le potentiel zêta. Nous avons également caractérisé les propriétésmécaniques des aérogels par des essais de compression et leurs propriétés de conductionthermique dans le régime non stationnaire par la technique du fil chaud. Il s’est avéré qu’unestructuration multi-échelles de ces différentes celluloses favorise la création de méso etnanoporosités au détriment de la macroporosité. Ceci favorise le confinement de l’air dans le bioaérogelpar effet de Knüdsen et améliore ses propriétés d’isolation thermique. D'autre part lesnanoparticules (organiques et inorganiques) permettent d'avoir des aérogels de très bonnespropriétés mécaniques. Le troisième objectif était d'essayer d'autres charges minérales (autres quela zéolithe) dans les différentes celluloses et d’explorer les propriétés morphologiques,structurales, thermiques et mécaniques. Cette étude a permis de montrer l'importance descaractéristiques morphologiques et géométriques des charges minérales dans le contrôle despropriétés physiques et mécaniques des aérogels bio-hybrides. / This thesis focuses on the preparation, using freeze drying technique, of aerogels madefrom cellulose and mineral fillers intended for potential use in the field of thermal insulation. Thefirst goal of this thesis was the characterization of different cellulose (cellulose (PBPD)nanocrystals (NCC) and oxidized nanofibrils (NFCs)), the inorganic filler (mainly zeolite) and theresulting aerogels prepared by various combinations. We used for the characterization of thestarting materials and the aerogels analytical techniques such as x-ray diffraction (XRD), BET,SEM and the zeta potential. We also characterized the mechanical properties of the aerogels bycompression tests and their thermal conduction properties in the non-steady state by the hot wiretechnique. It has been found that multi-scale structure of these celluloses promotes the creation ofmeso and nanoporosities to the detriment of macroporosity. This promotes the confinement ofthe air in the bio-aerogel by Knudsen effect and improves their thermal insulation properties. Onthe other hand, the nanoparticles (organic and inorganic) allow the aerogels to have very goodmechanical properties. The third objective was to try other mineral fillers (other than the zeolite)in combination with the different cellulose and explore the morphological, structural, thermaland mechanical of the corresponding aerogels. This study has allowed showing the importance ofmorphological and geometrical characteristics of the mineral fillers in controlling physical andmechanical properties of the bio-hybrid aerogels.

We report on an efficient assembly approach to a variety of electrostatically stabilized all-inorganic semiconductor nanocrystals (NCs) via their linking with appropriate ions into multibranched gel networks. These all-inorganic non-ordered 3D assemblies can combine strong interparticle coupling which facilitates charge transport between the NCs with their diverse morphology, composition, size, and functional capping ligands. Moreover, the resulting dry gels (aerogels) are highly porous monolithic structures, which preserve the quantum confinement of their building blocks. The inorganic semiconductor aerogel made of 4.5 nm CdSe colloidal NCs, capped with iodide ions and bridged with Cd2+ ions, exhibited a surface area as high as 146 m2/g.

Le but de ce travail de thèse est de développer des aérogels biosourcés, mécaniquement résistants et thermiquement très isolants (voire super-isolants). Les aérogels à base de cellulose, souvent appelés « aérocelluloses », sont connus pour être très poreux et extrêmement légers. Ils présentent en revanche une grande dispersion de tailles de pores, donnant de propriétés thermiques relativement modestes. Nous avons étudié plusieurs approches pour améliorer la morphologie des aérocelluloses: la modification du solvant, la réticulation chimique de la cellulose et la formation d'hybrides avec d'autres polymères. La réticulation de la cellulose a réellement permis d'affiner la structure poreuse de l'aérocellulose vers une nano-structuration ce qui a amélioré la conductivité thermique, s'approchant du domaine de la super-isolation (0.026 W.m-1.K-1). Un autre polysaccharide, la pectine, a été utilisé pour préparer un aérogel également poreux et très léger, « l'aéropectine ». L'aéropectine et l'aérocellulose présentent de fortes similitudes dans leur morphologie. Cependant, l'aéropectine possède de meilleures propriétés thermiques, super-isolantes (0.020 W.m-1.K-1), grâce à la nano-structuration du réseau poreux. Ces aérogels sont 100% biosourcés avec un faible impact environnemental, et sont très prometteurs non seulement pour l'isolation thermique mais également pour de nombreuses autres applications, telle que la libération contrôlée de médicaments ou la catalyse. La formation d'aérogel de silice à l'intérieur de la structure poreuse d'aéropectine a augmenté la surface spécifique jusqu'à 700 m2/g et a permis de diminuer la conductivité thermique (0.017 W.m-1.K-1). / The work aims at developing a new generation of bio-based aerogels, mechanically robust and thermally very insulating (super-insulating). Cellulose aerogels, called “aerocelluloses”, are known to be very porous and ultra-lightweight materials but present a wide range of pores and therefore moderate thermal insulating properties. We studied several approaches for tuning aerocellulose towards a finer and nanostructured morphology: modification of solvent, cellulose crosslinking and formation of cellulose-based hybrids. It was cellulose cross-linking that greatly improved aerocellulose structure towards a nano-structuration, reflected by the increase of specific surface area and the decrease of thermal conductivity, close to super-insulation (0.026 W.m-1.K-1). Another polysaccharide, pectin, was used for preparing a highly porous and very lightweight aerogel called “aeropectin”. Aeropectin and aerocellulose were compared; they present many similarities in their morphology. However, aeropectin has better thermal properties, reaching super-insulation (0.020 W.m-1.K-1). These bio-aerogels are 100% bio-based, environmentally friendly and present a high potential not only for thermal insulation but also for a broad range of other applications such as controlled drug release and catalysis. The formation of silica aerogel directly inside the porous structure of aeropectin increased the specific surface area up to 700 m²/g and decreased thermal conductivity (0.017 W.m-1.K-1).

Nanomaterials have attracted considerable attention during the past decades due to their unique and fascinating properties. However, this class of materials is not an invention of modern age. People have been using nanomaterials for centuries, although unwittingly. Probably the most famous example for the usage of nanomaterials in ancient times is the Lycurgus Cup, a Roman glass cage cup created in the 4th century which changes the colour of its glass from green to ruby depending on the illumination conditions. The foundation for the development of the field of nanotechnology was laid by the speech of Feynman “There is plenty of room at the bottom” in 1959, in which he spoke about the principles of miniaturisation as low as to the atomic level. Today, modern nanotechnology made it its business to purposefully develop and synthesise nanomaterials as well as to face their applications in various fields, such as microelectronics, catalysis or biomedicine. However, the term “nanomaterials” does not solely involve the nanoparticulate units itself, but also their arrangement into two- or three-dimensional structures. Thereby, the maintenance of the nanoscale properties is one of the main challenges. This task was focussed by this work implied the preparation and macroscale arrangement of fluorescent QDs while preserving their optical properties. The main achievement of this work was the development of a novel aerogel material with non-quenching PL behaviour by using silica coated QDs as nanoparticulate building units. In comparison to other monolithic silica-QD structures or aerogels from pure QDs, a defined and controllable distance between the fluorescent QDs is provided in these structures by the silica shell. The spacing was shown to efficiently disable energy transfers so that no spectral shifts, lifetime shortening or PL QY losses are observed during the colloid to gel transition. The silica shell, established by a standard reverse microemulsion approach, was found to exhibit a certain porosity, which was proven by gas adsorption measurements. Existing cavities in the micro- and mesoporous range were found to allow small species such as metal ions to pass through the shell and interact with the QD core causing a detectable change of the PL intensity, which makes these materials suitable for future sensing applications. The gel preparation was based on a metal ion assisted complexation approach, which requires tetrazole functionalisation of the nanoparticulate building units. A major development in this work that permitted this gelation approach for silica-QDs was the development of a novel tetrazole-silane ligand. TMSPAMTz was specifically designed to bind to the silica surface of silica-QDs in aqueous solution and was prepared by a covalent coupling of an alkyl chained silane with a 5-subsituted tetrazole ring. Network formation is subsequently achieved by the interconnection of negatively charged tetrazole rings with metal ions, which allows for a broad spectrum of aerogel materials from different NP species as well as their mixtures as long as tetrazole capping is provided. Considering this diversity and the disabling of energy transfers, straightforward colour tuning was demonstrated herein by mixing differently emitting silica-QD species which gives great prospects for lighting applications. Furthermore, the possibility of plasmon enhanced emission was presented for mixed Au NP/silica-QD gels. With respect to future sensing applications, thin porous films from silica-QDs gels were prepared, which showed a promising concentration dependant PL quenching for the model analyst hydrogen peroxide. However, the film reproducibility of the applied drop-cast coating method was insufficient. As a suggestion to this, a LbL method was presented, wherein a gel is subsequently grown with the metal ion assisted complexation approach. In addition to the tetrazole ligands on the NP surface, tetrazole-silane ligands were used in this approach to functionalise the glass substrate surface. By this, homogeneous gel films of distinct thickness can be grown while the use of organic polymers can be completely avoided. Besides the preparation of NP assemblies, standard Cd-based QD materials as well as Au NPs of different sizes and shape, recent progresses in the synthesis of InP-based QDs were presented in this work. A thorough investigation and understanding of the growth influencing parameters allowed for the establishment of preparation routes for In(Zn)P/GaP/ZnS core/shell/shell QDs with emission wavelengths tuneable within a large range from 500 to 650 nm, narrow peak widths of 45 to 70 nm and PL QYs up to 60%. Successful incorporation of these QDs into salt matrices was further demonstrated. The resulting composite materials are very photostable and suitable as colour conversion materials for solid state lighting, as was clearly pointed out by a self-prepared WLED that met the standard commercial LEDs.

Les batteries lithium-air et Li-S sont des techniques prometteuses pour un stockage efficace d’énergie électrochimique. Les principaux défis sont de développer un électrolyte solide à haute conductivité ionique et des cathodes efficaces. Dans ce travail, des aérogels de carbone conducteurs avec une double porosité ont été synthétisés en utilisant la méthode de sol-gel. Ils ont été utilisés comme cathode dans des batteries lithium-air. Ces cathodes peuvent fournir deux types de canaux pour le stockage de produits de décharge, facilitant la diffusion gaz-liquide et réduisant ainsi le risque de colmatage. Presque 100 cycles été obtenus avec une capacité de 0,4 mAh et une densité de courant de 0,1 mA/cm². Pour le développement d'électrolyte solide stable et conducteur, les sulfures, en particulier Li4SnS4 et son dérivé Li10SnP2S12 ont été particulièrement étudiés. Ces composés ont été synthétisés en utilisant une technique en deux étapes comprenant la mécanosynthèse et un traitement thermique à température relativement basse qui a été optimisé afin d'améliorer la conductivité ionique. La meilleure conductivité obtenue est de 8,27×10-4 S / cm à 25°C et ces électrolytes présentent une grande stabilité électrochimique sur une large gamme de voltage de 0,5 à 7V. Les couches minces ont également été déposées en utilisant la technique de pulvérisation cathodique, avec en général une conductivité ionique améliorée. La performance des batteries Li-S assemblées avec ces électrolytes massifs doit être améliorée, en particulier en améliorant la conductivité ionique de l'électrolyte. / Lithium-air and Li-S batteries are promising techniques for high power density storage. The main challenges are to develop solid electrolyte with high ionic conductivity and highly efficient catalyzed cathode. In this work, highly conductive carbon aerogels with dual-pore structure have been synthesized by using sol-gel method, and have been used as air cathode in Lithium-air batteries. This dual- pore structure can provide two types of channels for storing discharge products and for gas-liquid diffusion, thus reducing the risk of clogging. Nearly 100 cycles with a capacity of 0.4mAh at a current density of 0.1 mA cm-2 have been obtained. For developing stable and highly conductive solid electrolyte, sulfides, especially Li4SnS4 and its phosphorous derivative Li10SnP2S12 have been particularly investigated. These compounds have been synthesized by using a two-step technique including ball milling and a relatively low temperature heat treatment. The heat treatment has been carefully optimized in order to enhance the ionic conductivity. The best-obtained conductivity is 8.27×10-4 S/cm at 25°C and the electrolytes show high electrochemical stability over a wide working range of 0.5 – 7V. Thin films have also been deposited by using the sputtering technique, with generally improved ionic conductivity. The performance of the Li-S batteries assembled with these bulk electrolytes is still to be improved, particularly by improving the ionic conductivity of the electrolyte.

Tato práce se zabývá systematickou studií syntézy a zpracováním pokročilých tepelně stabilních aerogelů pro potenciální vysokoteplotní aplikace. V první části dizertační práce jsou podrobně popsány syntetické implikace pro přípravu aerogelů a jejich aplikace spolu s popisem depozičních metod povlaků vytvořených pomocí sol-gel procesu. Experimentální postup je rozdělen do tří částí. První z nich představuje syntetické protokoly k přípravě ZrO2, YSZ, Ln2Zr2O7 (Ln = La3+, Nd3+, Gd3+, and Dy3+) aerogelů, Ln2Zr2O7 prášků a xerogelů. Dále je popsána depoziční metoda, která byla použita pro přípravu povlaků z aerogelů na kovových substrátech. Poté jsou následně specifikovány techniky, jež byly použity pro charakterizaci. Bylo zjištěno, že množství vody a kyseliny dusičné hraje rozhodující roli v přípravě gelů vhodných pro transformaci na aerogely. Po kalcinaci při 500 °C mají ZrO2 a YSZ aerogely velký povrch, a to až do 114 m2 g-1, avšak při 1000 °C dochází k úplnému zhuštění a ztrácí se tak veškerá jejich porézní struktura. Naopak ve srovnání s ZrO2 and YSZ jsou aerogely Ln2Zr2O7 tepelně stabilnější, protože si zachovávají svou porozitu při vyšší kalcinační teplotě (1000 °C), při které dosahují hodnot > 160 m2 g-1. Experimentálně bylo dále zjištěno, že ve studovaném teplotním rozsahu ZrO2 aerogel tvoří tetragonální komplex monoklinický fázový přechod řízený velikostí krystalitů, zatímco YSZ je tvořena jedinou tetragonální fází. Fázové složení zirkoničitanů vzácných zemin je vysoce závislé na způsobu syntézy; všechny Ln2Zr2O7 materiály jsou pyrochlorické nebo fluoritové krystalické fáze. Přímým odléváním aerogelu na kovový substrát dochází k úplnému rozpraskání povlaku z důvodu smršťování, zatímco máčením kovového substrátu v suspenzi je možné vyrobit homogenní, silné a hrubé povlaky z aerogelu. Tyto povlaky neobsahují fázové změny a zůstávají vysoce porézní i po různých tepelných úpravách.

Nanomaterials have attracted considerable attention during the past decades due to their unique and fascinating properties. However, this class of materials is not an invention of modern age. People have been using nanomaterials for centuries, although unwittingly. Probably the most famous example for the usage of nanomaterials in ancient times is the Lycurgus Cup, a Roman glass cage cup created in the 4th century which changes the colour of its glass from green to ruby depending on the illumination conditions. The foundation for the development of the field of nanotechnology was laid by the speech of Feynman “There is plenty of room at the bottom” in 1959, in which he spoke about the principles of miniaturisation as low as to the atomic level. Today, modern nanotechnology made it its business to purposefully develop and synthesise nanomaterials as well as to face their applications in various fields, such as microelectronics, catalysis or biomedicine. However, the term “nanomaterials” does not solely involve the nanoparticulate units itself, but also their arrangement into two- or three-dimensional structures. Thereby, the maintenance of the nanoscale properties is one of the main challenges. This task was focussed by this work implied the preparation and macroscale arrangement of fluorescent QDs while preserving their optical properties. The main achievement of this work was the development of a novel aerogel material with non-quenching PL behaviour by using silica coated QDs as nanoparticulate building units. In comparison to other monolithic silica-QD structures or aerogels from pure QDs, a defined and controllable distance between the fluorescent QDs is provided in these structures by the silica shell. The spacing was shown to efficiently disable energy transfers so that no spectral shifts, lifetime shortening or PL QY losses are observed during the colloid to gel transition. The silica shell, established by a standard reverse microemulsion approach, was found to exhibit a certain porosity, which was proven by gas adsorption measurements. Existing cavities in the micro- and mesoporous range were found to allow small species such as metal ions to pass through the shell and interact with the QD core causing a detectable change of the PL intensity, which makes these materials suitable for future sensing applications. The gel preparation was based on a metal ion assisted complexation approach, which requires tetrazole functionalisation of the nanoparticulate building units. A major development in this work that permitted this gelation approach for silica-QDs was the development of a novel tetrazole-silane ligand. TMSPAMTz was specifically designed to bind to the silica surface of silica-QDs in aqueous solution and was prepared by a covalent coupling of an alkyl chained silane with a 5-subsituted tetrazole ring. Network formation is subsequently achieved by the interconnection of negatively charged tetrazole rings with metal ions, which allows for a broad spectrum of aerogel materials from different NP species as well as their mixtures as long as tetrazole capping is provided. Considering this diversity and the disabling of energy transfers, straightforward colour tuning was demonstrated herein by mixing differently emitting silica-QD species which gives great prospects for lighting applications. Furthermore, the possibility of plasmon enhanced emission was presented for mixed Au NP/silica-QD gels. With respect to future sensing applications, thin porous films from silica-QDs gels were prepared, which showed a promising concentration dependant PL quenching for the model analyst hydrogen peroxide. However, the film reproducibility of the applied drop-cast coating method was insufficient. As a suggestion to this, a LbL method was presented, wherein a gel is subsequently grown with the metal ion assisted complexation approach. In addition to the tetrazole ligands on the NP surface, tetrazole-silane ligands were used in this approach to functionalise the glass substrate surface. By this, homogeneous gel films of distinct thickness can be grown while the use of organic polymers can be completely avoided. Besides the preparation of NP assemblies, standard Cd-based QD materials as well as Au NPs of different sizes and shape, recent progresses in the synthesis of InP-based QDs were presented in this work. A thorough investigation and understanding of the growth influencing parameters allowed for the establishment of preparation routes for In(Zn)P/GaP/ZnS core/shell/shell QDs with emission wavelengths tuneable within a large range from 500 to 650 nm, narrow peak widths of 45 to 70 nm and PL QYs up to 60%. Successful incorporation of these QDs into salt matrices was further demonstrated. The resulting composite materials are very photostable and suitable as colour conversion materials for solid state lighting, as was clearly pointed out by a self-prepared WLED that met the standard commercial LEDs.