O presente trabalho apresenta uma discussão de metodologia para o diagnóstico e ações para redução de perdas de água, auxiliando na determinação do perfil das perdas, permitindo uma melhor priorização das ações de combate e redução de perdas reais (físicas) e perdas aparentes (comerciais). Para o desenvolvimento desta metodologia, foi realizada uma ampla revisão bibliográfica, onde é apresentada a conceituação geral sobre perdas de água, suas causas e ocorrências, indicadores, ações para redução, e uma abordagem detalhada quanto às metodologias existentes para avaliação de perdas e ferramentas disponíveis para isto. A metodologia aqui aplicada desenvolve a avaliação das perdas através do balanço hídrico, utilizando o software gratuito desenvolvido pelo Banco Mundial (W-B Easy Calc - v1.17), e foi aplicada no sistema de abastecimento de água da Região Metropolitana de São Paulo (RMSP). Foram levantados os dados básicos de controle do sistema e realizados ensaios de campo, com medições de pressão e ensaios para determinação das perdas aparentes. Como estudo de caso, a metodologia foi aplicada em três setores de abastecimento da área central da RMSP, com características distintas. Os resultados do diagnóstico das perdas foram coerentes com as expectativas. Em função dos resultados, em cada setor deverá ser desenvolvida uma estratégia específica para a redução de perdas. / This study presents a discussion of a methodology for diagnosis and actions to reduce water losses, to assist in determining the profile of water losses, allowing a better prioritization of actions to combat and reduce real (physical) losses and apparent (commercial) losses. For developing the methodology, it was conducted an extensive bibliography review, where is presented the general concepts on water losses, its causes and events, indicators, actions to reduce, and a detailed discussion about the existing methodologies to assess losses and tools available for this. The applied methodology consists of an assessment of losses through the water balance, using free software developed by the World Bank (WB Easy Calc - v1.17) and it was applied in the water supply system in metropolitan region of Sao Paulo. To do this, it was necessary to collect basic data of system control and field tests, with pressure measurements and tests to determine apparent losses. As case study, the methodology was applied in three supply zones at the central area of metropolitan region of Sao Paulo, with different characteristics. The results of water losses diagnosis were consistent with expectations. With these results, a specific strategy should be developed in each sector for reducing losses.

Neste trabalho foi avaliada a influência das condições de processamento (pouring temperature and de vazamento e condições de isolamento térmico dos moldes cerâmicos) na formação de trincas nas palhetas de turbinas policristalinas, a base da superliga B1914, produzidas por microfusão. E devido à falta de informações sobre a superliga B1914 foram levantadas informações sobre o equilíbrio de fases (THERMOCALC) e foi realizada a caracterização microestrutural e mecânica deste material desta liga no estado bruto e tratada termicamente. Todas as palhetas vazadas a 1570, 1520 e 1470 °C em moldes sem isolamento e com isolamento parcial apresentaram trincas e outros defeitos de solidificação. Já as palhetas vazadas em moldes totalmente isolados estavam livres das trincas. No entanto foram identificados aglomerados de microporos na raíz de todas as palhetas. Os resultados de simulação de fração de fases mostraram que o equilíbrio de fases da superliga B1914 é constituído majoritariamente pelas fases γ e γ\' e pelas fases minoritárias MB2, M3B2 e sigma. A caracterização microestrutural da superliga B1914 confirmou os resultados de simulação e foram identificadas as fases gama (&#947) - dendritas e os precipitados da fase gama linha (&#947\') - no interior das dendritas e na região interdendrítica. As fases M3B2 e eram os microconstituintes do eutético. Os resultados de DTA e Scheil mostraram que o processo de solidificação, da superliga B1914, ocorreu fora de equilíbrio. Nos resultados obtidos a partir dos tratamentos térmicos, ficaram evidentes as dificuldades encontradas para solubilização das placas da fase &#947\'. A integridade estrutural dos corpos-de-prova foi comprometida pela presença de defeitos de solidificação (vazios). Tanto que os valores de LR e r obtidos nos ensaios estão muito abaixo dos valores encontrados na literatura. / This study was evaluated the influence of processing conditions (temperatures of casting conditions and thermal insulation of ceramic shells) in crack formation of equiaxed B1914 turbine blades produced by investment casting. Due to lack of information about B1914 alloy was performed microstructural and mechanical characterization of this alloy material in the raw state and treated. In shells uninsulated and partly insulated, after pouring was observed casting solidification defects. However the shells in a fully insulated were not observed casting crack formation. However were identified clusters of micropores in the root of all blades. The results of simulation phase fraction showed that the balance of phases in B1914 alloy is made mostly by γ and γ\' phases and the minority phases: MB2, M3B2 and sigma. The microstructural characterization of B1914 alloy confirmed the results of simulation and were identified: gamma (γ) - dendrites and gamma prime (γ\') - inside the dendrites and interdendritic regions. The M3B2 was found in eutectic. The results of DTA and Scheil showed that the process of solidification occurred in non-equilibrium. The results obtained from the thermal treatments showed difficulties to solubilize γ\' phase. The structural integrity of samples was compromised by the presence of solidification defects (pores). Both values of LR and εr obtained in the tests are much below the values found in literature.

Vid framställning av olika material är introduceringen av legeringselement ett betydelsefullt område. Vid framställning av stål kan egenskaperna för stålet optimeras genom att styra de kemiska reaktionerna som sker i samband med att stålet legeras. För legeringar av stål är låga halter av grundämnet bor av intresse. Tillsatser av bor vid ståltillverkningen har visats ge betydande förbättringar av olika materialegenskaper för stål. Ett känt problem är att bor uppvisar hög affinitet till flera andra grundämnen. Detta leder till att bor vid materialtillverkningen bildar ej önskvärda kemiska föreningar med dessa ämnen vilket leder till att borets bidrag till stålets egenskaper förloras i hög utsträckning.Med hjälp av termodynamiska beräkningsmodeller, såsom CALPHAD-metoden, går det att beräkna olika termodynamiska beskrivningar av kemiska föreningar. Dessa kan därefter sammanställas i databaser för framtida beräkningar. Genom att utföra utvärderingar och beräkningar på system av lägre grad, t.ex. binära system, kan i förlängningen mer komplexa beräkningar utföras på multikomponenta system som innehåller flera olika grundämnen. Databasen i detta projekt saknar en uppdaterad beskrivning av tillgänglig termodynamisk informationen för vissa borkarbider. Syftet med detta examensarbete var att utföra en utvärdering av stål mikrolegerat med bor och utföra en uppdatering av en databas med avseende på utvalda kemiska föreningar. Med programvaran Thermo-Calc har en termodynamisk utvärdering skett av Fe-B-C-systemet med avseende på de tidigare ej beskrivna borkarbiderna Fe3(B,C) och Fe23(B,C)6. Deframtagna beskrivningarna av föreningarna implementerades i databasen på ekvationsform och beräkningar utfördes för att påvisa pålitligheten i beskrivningarna. Resultaten från beräkningarna visades överensstämma väl med referenser i litteraturen. / When studying the production of different materials, the introduction of alloying elements is of great importance. The material properties of steels can be optimized through control of the different chemical reactions taking place in the production process. For different steel alloys, alloying with the element boron has shown an increased hardenability for the end products. One problem with boron is that it shows high affinity to several other elements. This can lead to boron forming different chemical compounds that are not desired and thus losing the contribution of boron to the hardenability effect. With the help of thermodynamic calculation models, such as the CALPHAD-method, it is now possible to calculate different kinds of thermodynamic descriptions for chemical compounds. These descriptions can be used in databases for future calculations. By making evaluations of thermodynamic systems of lower degrees, for example a binary system, one could perform more complex calculations of systems involving many elements and compounds. The database used in this project lacked an updated thermodynamic description of selected boron carbides. The purpose of this Master’s Thesis was to perform a thermodynamic evaluation of steel alloyed with small amounts of boron. Using the updated descriptions, the database was updated with the latest thermodynamic information regarding the chemical compounds of Fe3(C,B) and Fe23(C,B)6.A thermodynamic evaluation has been performed using the software Thermo-Calc for the boron carbides Fe3(C,B) and Fe23(C,B)6 in the ternary system Fe-B-C. These new descriptions were implemented in the database and through calculations validated against published articles and journals. The results from the calculations were shown to be satisfactory when comparing to other published results.

O uso do cálculo termodinâmico e consequentemente base de dados desenvolvidas para esse propósito é hoje uma das ferramentas fundamentais para o aprimoramento e desenvolvimento de superligas a base de níquel. A proposta deste trabalho foi avaliar a confiabilidade de uma base de dados comercial, específica para superligas a base de níquel, utilizada em softwares de cálculos termodinâmicos computacionais. Comparou-se os dados experimentais da superliga Inconel 713LC com informações obtidas através do calculo termodinâmico para a composição química específica da superliga estudada. As amostras da superliga comercial Inconel 713LC foram retiradas de barras da liga fundida a vácuo (VIM). Os tratamentos térmicos foram realizados sob atmosfera de argônio em cápsulas de quartzo nas temperaturas de 600?C, 900?C e 1250 ?C nos tempos de 10h, 24h, 50h, 100h, 250h, 500h, 1000h e 2000 horas, de acordo com a temperatura de tratamento utilizada, visando acompanhar o desenvolvimento microestrutural até alcançar a condição de equilíbrio termodinâmico. Previamente, a amostra no estado bruto de fusão e as amostras após os tratamentos de equilíbrio foram caracterizadas microestruturalmente via microscopia eletrônica de varredura (MEV) e a composição das fases medidas por microanálise de energia dispersiva (EDS). As temperaturas das transformações de fases foram medidas por analise térmica diferencial (DTA). Nas amostras também foram realizadas medidas de microdureza para acompanhar indiretamente a evolução microestrutural da fase gama prime. Para os cálculos termodinâmicos foram utilizados o software Thermo-Calc® e a base de dados TTNi8 da empresa Thermotech Ltd®. / The computational thermodynamic simulation and the databases designed for this purpose are today one the most important tools to develop new nickel based superalloys. The aim of this work was to check the reliability of a commercial database, designed specifically for Ni-based superalloys. The experimental phase diagram data of Inconel 713LC, such as, liquidus and solidus temperatures as well as chemical phase compositions were compared with thermodynamic information extracted from computational simulations. Samples of a commercial superalloy Inconel 713LC were extracted from an ingot produced by Vacuum Induction Melting (VIM) and heat treated under argon in quartz capsules at 600?C, 900 ?C and 1250?C for 10h, 24h, 50h, 100h, 250h, 500h, 1000h and 2000h, according to the treatment temperature used, aiming at reaching the thermodynamic equilibrium conditions. The as-cast and all heat-treated samples were characterized by Scanning Electron Microscopy (SEM) and the chemical compositions of the phases were measured via Energy Dispersive X-ray Spectroscopy (EDS). Temperatures of phase transformations were determined by Differential Thermal Analysis (DTA). Microhardness measurements were performed to indirectly follow the microstructural evolution of gamma prime. The Thermo-Calc® software and the TTNi8 database from Thermotech Ltd® were used for thermodynamic calculations.

Neste trabalho foi avaliada a influência das condições de processamento (pouring temperature and de vazamento e condições de isolamento térmico dos moldes cerâmicos) na formação de trincas nas palhetas de turbinas policristalinas, a base da superliga B1914, produzidas por microfusão. E devido à falta de informações sobre a superliga B1914 foram levantadas informações sobre o equilíbrio de fases (THERMOCALC) e foi realizada a caracterização microestrutural e mecânica deste material desta liga no estado bruto e tratada termicamente. Todas as palhetas vazadas a 1570, 1520 e 1470 °C em moldes sem isolamento e com isolamento parcial apresentaram trincas e outros defeitos de solidificação. Já as palhetas vazadas em moldes totalmente isolados estavam livres das trincas. No entanto foram identificados aglomerados de microporos na raíz de todas as palhetas. Os resultados de simulação de fração de fases mostraram que o equilíbrio de fases da superliga B1914 é constituído majoritariamente pelas fases γ e γ\' e pelas fases minoritárias MB2, M3B2 e sigma. A caracterização microestrutural da superliga B1914 confirmou os resultados de simulação e foram identificadas as fases gama (&#947) - dendritas e os precipitados da fase gama linha (&#947\') - no interior das dendritas e na região interdendrítica. As fases M3B2 e eram os microconstituintes do eutético. Os resultados de DTA e Scheil mostraram que o processo de solidificação, da superliga B1914, ocorreu fora de equilíbrio. Nos resultados obtidos a partir dos tratamentos térmicos, ficaram evidentes as dificuldades encontradas para solubilização das placas da fase &#947\'. A integridade estrutural dos corpos-de-prova foi comprometida pela presença de defeitos de solidificação (vazios). Tanto que os valores de LR e r obtidos nos ensaios estão muito abaixo dos valores encontrados na literatura. / This study was evaluated the influence of processing conditions (temperatures of casting conditions and thermal insulation of ceramic shells) in crack formation of equiaxed B1914 turbine blades produced by investment casting. Due to lack of information about B1914 alloy was performed microstructural and mechanical characterization of this alloy material in the raw state and treated. In shells uninsulated and partly insulated, after pouring was observed casting solidification defects. However the shells in a fully insulated were not observed casting crack formation. However were identified clusters of micropores in the root of all blades. The results of simulation phase fraction showed that the balance of phases in B1914 alloy is made mostly by γ and γ\' phases and the minority phases: MB2, M3B2 and sigma. The microstructural characterization of B1914 alloy confirmed the results of simulation and were identified: gamma (γ) - dendrites and gamma prime (γ\') - inside the dendrites and interdendritic regions. The M3B2 was found in eutectic. The results of DTA and Scheil showed that the process of solidification occurred in non-equilibrium. The results obtained from the thermal treatments showed difficulties to solubilize γ\' phase. The structural integrity of samples was compromised by the presence of solidification defects (pores). Both values of LR and εr obtained in the tests are much below the values found in literature.

Lead (Pb) is frequently used as an alloying element in brass to enhance machinability and castability. However, this element poses a significant risk to human health and the environment. The 2021 revision of the Drinking Water Directive imposed stricter limits on Pb content in brass, encouraging the development of lead-free brass. Several studies have identified tin (Sn) as a potential substitute for Pb in brass. This master’s thesis examines the thermodynamic description of the Cu-Zn-Sn ternary system, using the Swerim Cu database. The investigation involved casting five alloys in the Cu-rich corner, followed by heat treatment at 550 oC until homogenized, and quenching, after which the samples were analyzed to determine the bcc and fcc phase composition. The results were used to confirm the thermodynamic description, and the ternary parameters of the fcc and bcc phases were optimized to match the experimental results. After the optimization, a significant enhancement is achieved in the description of the Cu-Zn-Sn ternary system, which better fits the experimental data. / Bly  (Pb)  används  ofta  som  ett  legeringselement  i  mässing  för  att  förbättra bearbetbarheten och  gjutbarheten.    Detta  element  utgör  dock  en  betydande  risk för människors  hälsa  och miljön.   2021 års översyn  av  dricksvattendirektivet införde strängare  gränser  för  Pb-halten  i mässing,  vilket  uppmuntrade utvecklingen av blyfri mässing.    Flera  studier  har  identifierat tenn  (Sn)  som  ett potentiellt substitut  för  Pb i mässing.   Denna  masteruppsats  undersöker den termodynamiska beskrivningen  av det ternära  Cu-Zn-Sn-systemet  med  hjälp  av Swerim Cu-databasen.   Undersökningen innefattade  gjutning  av  fem  legeringar  i det  Cu-rika hörnet, följt av värmebehandling vid 550 oC tills de homogeniserades, och härdning, varefter proverna analyserades  för  att bestämma  bcc-  och  fcc-fassammansättningen.   Resultaten  användes  för att  bekräfta den  termodynamiska  beskrivningen,  och  de  ternära  parametrarna  för  faserna  fcc och bcc  optimerades  för  att  matcha  experiment resultaten.  Efter  optimeringen  uppnås  en betydande  förbättring  av  beskrivningen  av  det  ternära  Cu-Zn-Sn-systemet,  vilket bättre  passar experimentdata.

Thermo-Calc software AB develops high quality thermodynamic and kinetic databases to predict and simulate accurately multi-component phase behaviour in complex systems. One problem with their Ni-based alloys and superalloy solutions database (TCNI8) is poor description of tungsten partitioning for multi-component nickel based alloys. This work investigates the thermodynamic description of some lower-order systems i.e., Ni-W, Al-Ni-W and Cr-Ni-W by performing key experiments on three binary Ni-W alloys, and two ternary alloys (Al-Ni-W and Cr-Ni-W). Experiments at four different temperatures were carried out in which alloys were homogenized, equilibrated, quenched and investigated to determine the equilibrium solid/liquid compositions. Experimental results are used to validate the thermodynamic descriptions of the liquid and the fcc phase. Unlike ternary Al-Ni-W and Cr-Ni-W, binary Ni-W reproduced the experimental information in a satisfactory way. Ternary parameters for fcc are changed to fit the experimental results of this work. The findings of this work highlight that ternary parameters for the fcc of Al-Ni-W and Cr-Ni-W systems significantly effect the tungsten partitioning values in higher order systems. / Thermo-Calc Software AB utvecklar termodynamiska och kinetiska databaser av hög kvalitet för att korrekt kunna förutsäga och simulera jämvikter och fasomvandlingar i komplexa flerkomponentsystem. Ett problem med deras databas för Ni-baslegeringar och superlegeringar (TCNI8) är att beskrivning av volframpartitionering stämmer dåligt för nickelbaslegeringar. I detta arbete undersöktes den termodynamiska beskrivningen av vissa lägre system, dvs Ni-W, Al-Ni-W och Cr-Ni-W genom att utföra nyckelförsök på tre binära Ni-W-legeringar och två ternära legeringar (Al-Ni-W och Cr-Ni-W). Experimentvid fyra temperaturer utfördes i vilka legeringarna homogeniserades,jämviktsbehandlades, släcktes och undersöktes för att bestämma sammansättning för jämvikt fast fas/smälta. De erhållna experimentella resultaten användes för att validera den termodynamiska beskrivningen av smältan och fcc-fasen. Till skillnad från ternära Al-Ni-W ochCr-Ni-W, reproducerade den experimentella informationen den binära Ni-W-beskrivningen tillfredsställande. Ternära parametrar för fcc justerades efter de experimentella resultaten från detta arbete. Resultaten visar att de ternära parametrarna för fcc i Al-Ni-W och Cr-Ni-W systemen signifikant påverkar volframs fördelning mellan fast fas och smälta i nickelbaslegeringar.

Aluminium applications in automotive will increase by 25 % over the next decade, mainly driven by the electrification and the reduction of fuel consumption. This diploma work aims to increase the understanding of the chemical interactions between aluminium alloys and typical tool systems in metal cutting. First the temperature at the tool-chip interface was estimated by FEM simulations, using the software AdvantEdge. Thereafter the chemical interaction of the tool-chip interface was calculated at the simulated temperature using the Thermo-Calc software. The thermodynamic data and descriptions of the multicomponent systems used where found in the literature, assessed by other authors, but critically reviewed for the use in this work. The results of the FEM simulations indicate that the temperature for machining aluminium with PCD and cemented carbide is between 60-80 % of the melting temperature of Al7wt %Si alloy. The calculations of the chemical interaction in turn results in that several hard precipitates can stick to or transform on the surface of the workpiece or tool-chip interface, for example SiC, Al4C3 and evidently diamond from the tool. This work concluded that more predictive modelling is needed to refine the results and the results from this work needs to be confirmed with experiments. The results show that the modelling can predict the reaction phases at the tool-chip interface, this can be used as input for the tool wear mechanisms during development of tooling solutions. / Aluminium användningen inom fordonsindustrin förväntas öka med 25 % under det närmsta decenniet, främst på grund av elektrifiering men också för att för att minska bränsleförbrukning. Målet med detta examensarbete är till att öka förståelsen för de kemiska interaktionerna mellan aluminiumlegeringar och typiska verktygssystem vid metallskärning, framförallt vid bearbetning av aluminiumlegeringar innehållande kisel med ett TiN-belagt PCD-verktyg och icke-belagda verktyg. Detta gjordes genom prediktiva FEM-simuleringar av temperatur, med hjälp av mjukvaran AdvantEdge. Parallellt med detta skapades databaser för simulering av den kemiska interaktionen mellan skär och bearbetningsmaterial i programvaran Thermo-Calc. De termodynamiska data och beskrivningarna av de termodynamiska system som används var bedömda av andra författare men kritiskt granskade för användning i detta arbete. Resultaten av FEM-simuleringarna gav den beräknade temperaturen för bearbetning av aluminium med PCD ligger någonstans mellan 60-80 % av smälttemperaturen för Al7wt % Si-legering. Beräkningarna av den kemiska interaktionen resulterar i sin tur i att flera hårda utskiljningar kan fastna på eller transformera på ytan mellan arbetsstycket och verktyget, till exempel SiC, Al4C3och diamant från verktyget. Resultaten från detta arbete visar att det går att förutsäga fasomvandlingar mellan skär och arbetsstycket, samt att detta kan användas som indata för skärförslitning under utvecklingen av verktygslösningar.

Current aircraft noise guidelines are based primarily on outdoor sound levels. However, human perception is highly related to indoor response, particularly for residences. A research project has been conducted that provides insight into how typical residential dwelling envelopes affect sound transmitted indoors. A focus has been placed on the effect of residential dwelling envelopes on subsonic civil aircraft noise. Typical construction types across the United States have been identified and used to develop model predictions of outdoor-to-indoor transmission loss. While it was initially hypothesized that these construction types could be grouped by climate region, it was found that these constructions are better grouped according to their outermost construction layer. Further, the impact of systematically altering construction variables (such as the construction materials used and the ratio of window area to wall area) has been investigated. Results will be used to better understand trends for expected noise reduction for typical construction types around the United States. Additionally, comparisons have been made between the effect of older and more modern wall construction techniques on whole-house performance.

Foi investigada a influência de elementos de liga como o Cromo, o Níquel, o Carbono e o Nitrogênio no intervalo de solidificação de um aço inoxidável martensítico fundido do tipo CA6NM. Este tipo de aço, utilizado na fundição de peças de grande porte, é bastante utilizado pela sua ótima resistência ao impacto, e boas propriedades contra corrosão em meio aquoso. Além disso, este aço possui ótima fundibilidade, tendo como principal característica seu reduzido intervalo de solidificação, o que torna diminutos os defeitos relacionados a este fenômeno. Resultados obtidos por cálculos termodinâmicos utilizando-se o Thermo-calc sugeriram forte dependência deste parâmetro em relação ao teor de Carbono (0,018%C a 0,044%C), com o intervalo de solidificação variando de 25°C a 43°C no intervalo de composições definidos pela norma como aceitáveis para a liga. Os outros elementos de liga analisados, segundo os cálculos termodinâmicos, não demonstraram influência significativa dentro das faixas toleradas pela norma. Foram fundidas 13 amostras com as composições químicas simuladas no Thermo-calc, e seus intervalos de solidificação foram investigados por análise térmica diferencial (DTA) e calorimetria exploratória diferencial (DSC). Contrariando os resultados do Thermo-calc, a influência do Carbono não foi comprovada, não havendo variação do intervalo de solidificação entre as amostras. Para confirmar os resultados de análise térmica, as amostras desta técnica foram analisadas por metalografia, não sendo observado qualquer tipo de reação no material ensaiado (descarbonetação, oxidação, etc). / The influence of alloying elements like Chromium, Nickel, Carbon and Nitrogen on the solidification interval on a CA6NM martensitic stainless steel casting was investigated. This steel class, mainly used on large castings, applies due to the fact that it has very good impact resistance, and satisfactory corrosion properties. Besides that, this stainless steel class has excellent castability, having as an important characteristic its reduced solidification interval, diminishing the tendency for solidification defects. The results obtained by thermodynamic calculations using Thermo-calc package have suggested a strong influence of the Carbon content on the solidification interval (25°C a 43°C) when the carbon content is varied within the range allowed by the alloy standard (0,018%C to 0,044%C). Other alloying elements, according to the thermodynamic calculations, have no influence over the solidification interval. Thirteen samples were cast based on the simulated chemical compositions and their solidification interval was investigated by differential thermal analysis (DTA) and differential scanning calorimetry (DSC). Contrary to the thermodynamic calculations, no influence of Carbon was observed on the solidification interval. In order to confirm the thermal analysis results, metallographic tests were performed on the DTA samples, with no observation of any unusual reaction on them, like oxidation or decarburizing.