High-speed, medium-resolution, analog-to-digital converters (ADCs) are important building blocks in a wide range of applications. High-speed, medium-resolution ADCs have been implemented by various ADC architectures such as a folding ADC, a subranging ADC, and a pipeline ADC. Among them, pipeline ADCs have proven to be efficient architectures for applications such as digital communication systems, data acquisition systems and video systems. Especially, power dissipation is a primary concern in applications requiring portability. Thus, the objective of this work is to design and build a low-voltage low-power medium-resolution (8-10bits) high-speed pipeline ADC in deep sub-micron CMOS technology. The non-idealities of the circuit realization are carefully investigated in order to identify the circuit requirements for a low power circuit design of a pipeline ADC. The resolution per stage plays an important role in determining overall power dissipation of a pipeline ADC. The pros and cons of both large and small number of bits per-stage are examined. A power optimization algorithm is developed to decide more accurately which approach is better for lower power dissipation. Both identical and non-identical number of bit per-stage approaches are considered and their differences are analyzed. A low-power, low-voltage 10-bit 100Msamples/s pipeline ADC was designed and implemented in a 0.18mm CMOS process. The power consumption was minimized with the right selection of the per-stage resolution based on the result of the power optimization algorithm and by the scaling down the sampling capacitor size in subsequent stages.

<p>The analog to digital converters is the key components in modern electronic systems. As the digital signal processing industry grows the ADC design becomes more and more challenging for researchers. In these days an ADC becomes a part of the system on chip instead of standalone circuit for data converters. This increases the requirements on ADC design concerning for example speed, power, area, resolution, noise etc. New techniques and methods are going to develop day by day to achieve high performance ADCs.</p><p>Of all types of ADCs the flash ADC is not only famous for its data conversion rate but also it becomes the part of other types of ADC for example pipeline and multi bit Sigma Delta ADCs. The main problem with a flash ADC is its power consumption, which increases in number of bits. This thesis presents the comparison of power consumption of different blocks in 1Gbps flash ADCs for 2, 4 and 6 bits in a 90nm CMOS technology. We also investigate the impact on power consumption by changing the design of decoder block.</p>

This thesis strives to enhance the performance of delta-sigma modulators in two areas: increasing their speed and enabling their operation in a low voltage environment. Parallelism based on time-interleaving can be used to increase the speed of delta-sigma modulators. A novel single-path time-interleaved architecture is derived and analyzed. Finite opamp gain and bandwidth result in a mismatch between the noise transfer functions of the internal quantizers which degrades the performance of the new modulator. Two techniques are presented to mitigate the mismatch problem: a hybrid topology where the first stage uses multiple integrators while the rest of the modulator uses a single path of integrators and a digital calibration method. The input-feedforward technique removes the input-signal component from the internal nodes of delta-sigma modulators. The removal of the signal component reduces the signal swing and distortion requirements for the opamps. These characteristics enable the reliable implementation of delta-sigma modulators in modern CMOS technology. Two implementation issues for modulators with input-feedforward are considered. First, the drawback of the analog adder at the quantizer input is identified and the capacitive input feedforward technique is introduced to eliminate the adder. Second, the double sampled input technique is proposed to remove the critical path generate by the input feedforward path. Novel input-feedforward delta-sigma architecture is proposed. The new digital input feedforward (DIFF) modulator maintains the low swing and low distortion requirements of the input feedforward technique, it eliminates the analog adder at the quantizer input, and it improves the achievable resolution. To demonstrate these advantages, a configurable delta-sigma modulator which can operate as a feedback topology or in DIFF mode is implemented in 0.18μm CMOS technology. Both modulators operate at 20MHz clock with an oversampling ratio of 8. The power consumption in the DIFF mode is 22mW and in feedback mode is 19mW. However, the DIFF mode achieves a peak SNDR of 73.7dB (77.1dB peak SNR) while the feedback mode achieves a peak SNDR of 64.3dB (65.9dB peak SNR). Therefore, the energy required per conversion step for the DIFF architecture (2.2 pJ/step) is less than half of that required by the feedback architecture (5.7 pJ/step).

This thesis presents two hybrid luminescence-based biochemical photosensory microsystems: a CMOS/microfluidic chemiluminescence contact imager, and a CMOS/thin-film fluorescence contact imager. A compact, low-power analog-to-digital converter (ADC) architecture for use in such sensory microsystems is also proposed. Both microsystems are prototyped in a standard 0.35um CMOS technology. The CMOS/microfluidic microsystem integrates a 64x128-pixel CMOS imager and a soft polymer microfluidic network. Circuit techniques are employed to reduce the dark current and circuit noise for low-level light sensitivity. Experimental validation is performed by detecting luminol chemiluminescence and electrochemiluminescence. The CMOS/thin-film microsystem integrates an existing 128x128-pixel CMOS imager and a prefabricated, high-performance optical filter. Experimental validation is performed by detecting human DNA labeled with Cyanine-3 fluorescent dye. The proposed ADC architecture employs a novel digital-to-analog converter with a flexible trade-off between the integration area and the conversion speed. The area savings and good linearity of the DAC are verified by simulations.

This thesis presents two hybrid luminescence-based biochemical photosensory microsystems: a CMOS/microfluidic chemiluminescence contact imager, and a CMOS/thin-film fluorescence contact imager. A compact, low-power analog-to-digital converter (ADC) architecture for use in such sensory microsystems is also proposed. Both microsystems are prototyped in a standard 0.35um CMOS technology. The CMOS/microfluidic microsystem integrates a 64x128-pixel CMOS imager and a soft polymer microfluidic network. Circuit techniques are employed to reduce the dark current and circuit noise for low-level light sensitivity. Experimental validation is performed by detecting luminol chemiluminescence and electrochemiluminescence. The CMOS/thin-film microsystem integrates an existing 128x128-pixel CMOS imager and a prefabricated, high-performance optical filter. Experimental validation is performed by detecting human DNA labeled with Cyanine-3 fluorescent dye. The proposed ADC architecture employs a novel digital-to-analog converter with a flexible trade-off between the integration area and the conversion speed. The area savings and good linearity of the DAC are verified by simulations.

This thesis strives to enhance the performance of delta-sigma modulators in two areas: increasing their speed and enabling their operation in a low voltage environment. Parallelism based on time-interleaving can be used to increase the speed of delta-sigma modulators. A novel single-path time-interleaved architecture is derived and analyzed. Finite opamp gain and bandwidth result in a mismatch between the noise transfer functions of the internal quantizers which degrades the performance of the new modulator. Two techniques are presented to mitigate the mismatch problem: a hybrid topology where the first stage uses multiple integrators while the rest of the modulator uses a single path of integrators and a digital calibration method. The input-feedforward technique removes the input-signal component from the internal nodes of delta-sigma modulators. The removal of the signal component reduces the signal swing and distortion requirements for the opamps. These characteristics enable the reliable implementation of delta-sigma modulators in modern CMOS technology. Two implementation issues for modulators with input-feedforward are considered. First, the drawback of the analog adder at the quantizer input is identified and the capacitive input feedforward technique is introduced to eliminate the adder. Second, the double sampled input technique is proposed to remove the critical path generate by the input feedforward path. Novel input-feedforward delta-sigma architecture is proposed. The new digital input feedforward (DIFF) modulator maintains the low swing and low distortion requirements of the input feedforward technique, it eliminates the analog adder at the quantizer input, and it improves the achievable resolution. To demonstrate these advantages, a configurable delta-sigma modulator which can operate as a feedback topology or in DIFF mode is implemented in 0.18μm CMOS technology. Both modulators operate at 20MHz clock with an oversampling ratio of 8. The power consumption in the DIFF mode is 22mW and in feedback mode is 19mW. However, the DIFF mode achieves a peak SNDR of 73.7dB (77.1dB peak SNR) while the feedback mode achieves a peak SNDR of 64.3dB (65.9dB peak SNR). Therefore, the energy required per conversion step for the DIFF architecture (2.2 pJ/step) is less than half of that required by the feedback architecture (5.7 pJ/step).

The analog to digital converters is the key components in modern electronic systems. As the digital signal processing industry grows the ADC design becomes more and more challenging for researchers. In these days an ADC becomes a part of the system on chip instead of standalone circuit for data converters. This increases the requirements on ADC design concerning for example speed, power, area, resolution, noise etc. New techniques and methods are going to develop day by day to achieve high performance ADCs. Of all types of ADCs the flash ADC is not only famous for its data conversion rate but also it becomes the part of other types of ADC for example pipeline and multi bit Sigma Delta ADCs. The main problem with a flash ADC is its power consumption, which increases in number of bits. This thesis presents the comparison of power consumption of different blocks in 1Gbps flash ADCs for 2, 4 and 6 bits in a 90nm CMOS technology. We also investigate the impact on power consumption by changing the design of decoder block.

abstract: ABSTRACT As the technology length shrinks down, achieving higher gain is becoming very difficult in deep sub-micron technologies. As the supply voltages drop, cascodes are very difficult to implement and cascade amplifiers are needed to achieve sufficient gain with required output swing. This sets the fundamental limit on the SNR and hence the maximum resolution that can be achieved by ADC. With the RSD algorithm and the range overlap, the sub ADC can tolerate large comparator offsets leaving the linearity and accuracy requirement for the DAC and residue gain stage. Typically, the multiplying DAC requires high gain wide bandwidth op-amp and the design of this high gain op-amp becomes challenging in the deep submicron technologies. This work presents `A 12 bit 25MSPS 1.2V pipelined ADC using split CLS technique' in IBM 130nm 8HP process using only CMOS devices for the application of Large Hadron Collider (LHC). CLS technique relaxes the gain requirement of op-amp and improves the signal-to-noise ratio without increase in power or input sampling capacitor with rail-to-rail swing. An op-amp sharing technique has been incorporated with split CLS technique which decreases the number of op-amps and hence the power further. Entire pipelined converter has been implemented as six 2.5 bit RSD stages and hence decreases the latency associated with the pipelined architecture - one of the main requirements for LHC along with the power requirement. Two different OTAs have been designed to use in the split-CLS technique. Bootstrap switches and pass gate switches are used in the circuit along with a low power dynamic kick-back compensated comparator. / Dissertation/Thesis / M.S. Electrical Engineering 2012

The notion of mechanical computation has been revived in the past few years, with the advances of nanofabrication techniques. Although electromechanical devices are inherently slow, they offer zero or very low off-state current, which reduces the overall power consumption compared to the fast complementary-metal-oxide-semiconductor (CMOS) counterparts. This energy efficiency feature is the most crucial requirement for most of the stand-alone battery-operated gadgets, biomedical devices, and the internet of things (IoT) applications, which do not require the fast processing speeds offered by the mainstream CMOS technology. In particular, using Micro-Electro-Mechanical (MEM) resonators in mechanical computing has drawn the attention of the research community and the industry in the last decade as this technology offers low power consumption, reduced circuit complexity compared to conventional CMOS designs, run-time re- programmability and high reliability due to the contactless mode of operation compared to other MEM switches such as micro-relays. In this thesis, we introduce digital circuit design techniques tailored for clamped-clamped beam MEM resonators. The main operation mechanism of these circuit blocks is based on fine-tuning of the resonance frequency of the micro-resonator beam, and the logic function performed by the devices is mainly determined by factors such as input/output terminal arrangement, signal type, resonator operation regime (linear/non-linear), and the operation frequency. These proposed circuits include the major building blocks of any microprocessor such as logic gates, a full adder which is a key block in any arithmetic and logic operation units (ALU), and I/O interface units, including digital to analog (DAC) and analog to digital (ADC) data converters. All proposed designs were first simulated using a finite element software and then the results were experimentally verified. Important aspects such as energy per operation, speed, and circuit complexity are evaluated and compared to CMOS counterparts. In all applications, we show that by proper scaling of the resonator’s dimensions, MHz operation speeds and energy consumption in the range of femto-joules per logic operation are attainable. Finally, we discuss some of the challenges in using MEM resonators in digital circuit design at the device level and circuit level and propose solutions to tackle some of them.

The objective of our research is to develop system architectures and CMOS circuits that interface with high-Q silicon microgyroscopes to implement navigation-grade angular rate sensors. The MEMS sensor used in this work is an in-plane bulk-micromachined mode-matched tuning fork gyroscope (M² – TFG ), fabricated on silicon-on-insulator substrate. The use of CMOS transimpedance amplifiers (TIA) as front-ends in high-Q MEMS resonant sensors is explored. A T-network TIA is proposed as the front-end for resonant capacitive detection. The T-TIA provides on-chip transimpedance gains of 25MΩ, has a measured capacitive resolution of 0.02aF /√Hz at 15kHz, a dynamic range of 104dB in a bandwidth of 10Hz and consumes 400μW of power. A second contribution is the development of an automated scheme to adaptively bias the mechanical structure, such that the sensor is operated in the mode-matched condition. Mode-matching leverages the inherently high quality factors of the microgyroscope, resulting in significant improvement in the Brownian noise floor, electronic noise, sensitivity and bias drift of the microsensor. We developed a novel architecture that utilizes the often ignored residual quadrature error in a gyroscope to achieve and maintain perfect mode-matching (i.e.0Hz split between the drive and sense mode frequencies), as well as electronically control the sensor bandwidth. A CMOS implementation is developed that allows mode-matching of the drive and sense frequencies of a gyroscope at a fraction of the time taken by current state of-the-art techniques. Further, this mode-matching technique allows for maintaining a controlled separation between the drive and sense resonant frequencies, providing a means of increasing sensor bandwidth and dynamic range. The mode-matching CMOS IC, implemented in a 0.5μm 2P3M process, and control algorithm have been interfaced with a 60μm thick M2−TFG to implement an angular rate sensor with bias drift as low as 0.1°/hr ℃ the lowest recorded to date for a silicon MEMS gyro.