Abstract Paper recycling is an ecological strategy for disposing of waste paper, but more importantly, recovered paper is an important source of raw material in the paper and board industry. Deinked pulp production from recovered paper has proved economically viable by comparison with virgin fibre pulp manufacturing, but this viability is now threatened by increasing waste disposal costs, as up to 25% of the raw material available for deinked pulp production can end up in the reject streams, which then have to be disposed of. The most common practice at present is incineration and disposal of the resulting ash in landfills, but tightening legislation has meant that landfills have become very expensive and are likely to be completely banned in the near future. Thus new ways have to be sought for managing the waste problem in deinked pulp production in order to ensure that the recycled paper production remain both economically and environmentally feasible. The aim of this thesis was to study means of improving the material efficiency of a deinked pulp mill without excessively detracting from end product quality or the performance of the combined sludge dewatering stage. First, an analytical procedure was developed for determining the utilisation potential of reject streams, and a considerable potential for material recovery from these streams was identified. The results presented here show that 80% of the most valuable long fibres from the fine-screening rejects and 15% of the fine material from the flotation froth reject can be recovered. Altogether, with the simultaneous recovery of both categories of reject, it would be possible to improve the material efficiency at the deinked pulp mill by a total of about 5 percentage units, which can be considered significant for process efficiency. Moreover, this would enable the fibre content of the combined sludge to be kept above a certain limit, so that the combined sludge dewatering properties would not be affected. Consequently, the results presented in this thesis provide several widely applicable means for improving the resource efficiency of a deinked pulp mill. / Tiivistelmä Paperin kierrätys uusiksi paperituotteiksi on ympäristöystävällinen tapa jätepaperin käsittelemiseksi. Uusiomassan valmistus on myös taloudellisesti kannattavaa verrattuna paperimassan valmistukseen neitseellisistä raaka-aineista. Taloudellinen kannattavuus on kuitenkin vaarassa jätemaksujen alati kasvaessa, sillä siistausmassan valmistuksessa jopa 25 % kierrätyspaperiraaka-aineesta päätyy jätejakeisiin, jotka hävitetään yleisesti polttamalla ja läjittämällä syntynyt tuhka kaatopaikalle. Lainsäädäntö on rajoittanut kaatopaikkasijoittamista ja se on nykyään hyvin kallista. Tulevaisuudessa jätteiden kaatopaikkasijoittaminen voi olla jopa täysin kiellettyä. Jäteongelman ratkaisemiseen tarvitaan siis uusia menetelmiä, jotta kierrätyspaperin valmistus säilyisi sekä taloudellisista että ympäristöllisistä näkökulmista kannattavana toimintana. Tämän väitöskirjatyön tavoitteena oli etsiä keinoja parantaa siistausmassan valmistuksen resurssitehokkuutta palauttamalla käyttökelpoisia materiaaleja jätevirroista takaisin prosessiin siten, ettei heikennetä lopputuotteen laatua eikä lietteidenkäsittelyprosessin toimintaa. Väitöstyön alussa kehitettiin analyysiproseduuri rejektivirtojen hyötykäyttöpotentiaalin arvioimiseksi ja siistamon rejektijakeissa havaittiin merkittävästi hyödynnettävää materiaalia. Tulokset osoittavat, että 80 % hienolajittelun rejekteissä poistuneista arvokkaista pitkistä kuiduista voidaan palauttaa takaisin prosessiin. Lisäksi flotaation vaahtorejektistä voidaan palauttaa 15 % hienoainetta. Palauttamalla yhtäaikaisesti sekä kuituja hienolajittelun rejekteistä että hienoainetta flotaation vaahtorejektistä, voidaan siistausmassan valmistuksen materiaalitehokkuutta parantaa yhteensä noin 5 prosenttiyksikköä, mikä on merkittävä parannus prosessitehokkuuteen. Kuitujen ja hienoaineen samanaikainen palauttaminen pitää lisäksi lietteiden käsittelyssä seoslietteen kuitupitoisuuden tarpeeksi korkeana, jotta sen vedenerotusominaisuudet säilyvät hyvinä. Tämän tutkimuksen tuloksena löydettiin siis useita laajalti sovellettavissa olevia keinoja siistausmassan valmistuksen resurssitehokkuuden parantamiseksi.

Skanskas bergtäkt, Vikan kross, i Göteborg producerar ett ersättningsmaterial till naturgruset i form av helkrossad betongballast. Utvinningen av naturgrus ska fasas ut eftersom det utvinns från grusåsar vilket är negativt för naturen då grusåsarna renar vatten och fungerar som naturliga vattenreservoarer. Historiskt sett har naturgruset använts till betongtillverkning under en väldigt lång tid och år 2013 investerade Vikan kross i en anläggning för att kunna producera helkrossad betongballast och på så vis fasa ut naturgruset från deras betongtillverkning. År 2014 stod anläggningen klar för att börja tillverka helkrossad betongballast. En lång uppstartsperiod där många tester utfördes för att få den helkrossade betongballasten att efterlikna naturgruset i form och egenskaper. I dagsläget producerar Vikan kross en bra ersättningsprodukt till naturgruset men produktionsledning har kommit underfund med att fuktkvoten på det ingående materialet till vindsikten har en stor påverkan på slutprodukten. Skanska gav mig i uppdrag att undersöka hur vindsiktens inställningar bör justeras beroende på vilken fuktkvot det ingående materialet har för att kunna bibehålla en acceptabel kornstorleksfördelning. Skanska har även önskemål att mängden filler (ballastkorn mindre än 63 μm) i slutprodukten skall öka från den mängd som finns i slutprodukten i dagsläget. En provtagningsplan baserad på tidigare tester och erfarenheter upprättades för att på så vis kunna följa vägen fram till ett bra resultat. Metoden som använts är provtagning av det ingående materialet samt det utgående materialet från vindsikten. Materialen har analyserats med hjälp av siktanalyser där kornstorleksfördelning har tagits fram. Vindsiktens inställningar har sedan varierats och ytterligare provtagning samt analyser har genomförts. När vindsikten ansågs producera helkrossad betongballast med så bra kornstorleksfördelning som möjligt bevattnades det ingående materialet till vindsikten. Vatten tillfördes för att höja fuktkvoten och på så vis förstå hur vindsiktens inställningar bör justeras för att behålla kornstorleksfördelningen inom de gränsvärden som finns. Resultatet visar att om det ingående materialet till vindsikten har en avvikande fuktkvot (> 1 vikt-%) är det möjligt att erhålla en kornstorleksfördelning som efterliknar den kornstorleksfördelning som erhålls när materialet har en normal fuktkvot (< 1 vikt-%). Mängden filler har inte ökat i slutprodukten eftersom att den ingående mängden filler till vindsikten redan är så låg att den inte går att justera med hjälp av enbart vindsikten. Orsaken till att mängden filler är lägre än vad som tidigare observerats kopplas till bergets geologi. Det berg som krossats under testperioden var väldigt hårt och där med produceras en mindre mängd filler. För en ökad mängd filler i slutprodukten krävs en förändring i krossprocessen före vindsikten. / Skanska Asfalt och Betong AB is the owner of the quarry Vikan kross in Gothenburg. They produce manufactured sand as a replacement product for the natural sand that is used in todays fin aggregates for concrete production. The Swedish government is limiting the extraction of natural sand because of environmental reasons. In 2013 Vikan kross invested in a plant to produce manufactured sand thus phasing out the natural sand from their concrete production. In 2014 the plant was ready to start producing manufactured sand. Through a long start-up period, many tests were done to get the manufactured sand to mimic the natural sand as much as possible. Today Vikan kross is producing a good replacement product for the natural sand, but the production team has come to the conclusion that the moisture content in the input material to the air classifier has a major impact on the final product. Skanska assigned me to investigate how the air classifiers settings should be adjusted depending on the moister content of the input material in order to maintain an acceptable particle size distribution. Skanska also wished that the amount of fines (particles smaller than 63 μm) in the manufactured sand should increase from the amount present today. A plan based on previous tests and experiences was set up in order to reach a good result. The method used was to take tests of the input materials as well as the output materials from the air classifier. The materials have been analyzed by using sieving methods to determinate the particle size distribution. The settings of the air classifier were then adjusted and further tests and analysis was done. When the air classifier was producing manufactured sand with a particle size distribution as good as possible, the input material was watered. Water was added to raise the moisture content to understand how the settings of the air classifier should be adjusted to maintain a particle size distribution within the limit values. The result shows that if the input material to the air classifier has a deviating moisture content (> 1 wt-%) it is possible to obtain a particle size distribution that mimics the particle size distribution obtained when the material has a normal moisture content (<1 wt-%). The amount of fines has not increased in the manufactured sand because the amount of fines in the input material is already so low that it can’t be adjusted by only changing the settings of the air classifier. The reason for the amount of fines being lower than previously observed is linked to the geology of the material. The material that had been crushed during this test period was very hard and thus produced a small amount of fines. For an increased amount of fines in the manufactured sand, a change is necessary in the process prior to the air classifier.

Some researchers have suggested that the weakest link of dental composites is thefiller-matrix bond. However, due to incompleteness of information dealing with this bond and its stability in a humid environment, it was considered desirable to investigate the effect of water on this region, as well as the influence of filler bonding and filler fraction on compressive strength and therm al expansion. Experimental composites containing different filler fractions of either silane-treatedor untreated fillers were made. Compressive strength and coefficient of thermalexpansion were determined using routine methods, while the hydrolytic degradation was investigated by measuring changes in concentrations of elements in the storagewater using atomic absorption spectrophotom etry. Scanning electron microscopicinvestigations were made on fractured samples. The diffusion coefficient of a representative resin system was determined gravimetrically. Seven commercial composites were investigated regarding hydrolyticdegradation. The filler compositions of these composite materials were determined by emission spectroscopy or energy-dispersive x-ray analysis before storage in distilledwater. This water was replaced and analyzed m onthly using plasma spectrophotom etryor atomic absorption spectrophotom etry. After completed water storage the samples were fractured and investigated by useof scanning electron microscopy.From the results of these studies the following conclusions were drawn: 1. The compressive strength of composites changes linearly with increased fillerfraction. Contrary to bonded fillers, composites containing unbonded fillers loststrength with increased filler fraction. 2. Water diffuses through the polymer m atrix and attacks the filler particles. This degradation is most pronounced for untreated fillers containing glass modifying elements such as sodium, barium and strontium. 3. The resin, used as a matrix, influences the speed with which the hydrolyticdegradation of the filler proceeds. 4. The hydrolytic degradation of the filler seemed to be associated w ith micro-crackform ation occurring in the matrix. Of the investigated composites, the micro-filledresin showed the lowest frequency of such crack formations. 5. The coefficient of ther al expansion decreases linearly with increased fillerfraction. Silane treatment did not influence this coefficient. 6. Using a simplified model to predict stresses in a particle filled composite indicatesthat rather high stress levels are induced in the polymer m atrix due to polym erizationshrinkage. This shrinkage induces radial compressive and tangential tensilestresses with respect to the filler surface. Increased filler fraction increases thetangential tensile stresses but reduces the compressive radial stresses. / <p>S. 1-66: sammanfattning, s. 67-168: 6 uppsatser</p> / digitalisering@umu

Abstract The amount of printing ink in a pulp suspension produced from recovered paper and its impact on overall brightness is commonly estimated from the reflectance-based ink content measured at a wavelength of 700 nm or 950 nm. The method uses a light scattering coefficient that can be measured from a slightly translucent test medium, i.e. of an opacity less than 97%. This is the case with machine-made papers in most instances. Alternatively, suitable opacity can be achieved by preparing a standard low-grammage sheet on a wire screen, but this results in poor retention of fibre fines, mineral fillers and printing inks, which is especially detrimental to ink measurement when the pulp suspension contains substantial amounts of printing inks. Hence opaque pads are often prepared on filter paper to achieve high retention. Unfortunately their high opacity prevents measurement of the light scattering coefficient, and thus a constant coefficient must be used for the determination of ink content. The aim of this thesis was to clarify the effects of retention and fine material changes on the light scattering coefficient in ink content measurement. The results showed that the light scattering properties of pulp in the wavelength region used for ink content analysis do not remain constant when the fine material content varies. The grade of the recovered paper, hyperwashing and flotation alter the fine material content and thus affect the light scattering. Printing ink also affects light scattering, but its practical impact is smaller than that of fibre fines and mineral fillers. The light scattering coefficient used for each ink content measurement needs to be representative, otherwise a systematic bias in ink content measurements may result from changes in the nature of the fine material and in its content. It is recommended that the light scattering coefficient should be measured in order to avoid this. The measurement should preferably be performed from a low-grammage sheet prepared on filter paper, as this ensures high retention and a measured value that represents better the initial state of the pulp suspension. / Tiivistelmä Mustepitoisuusmittaus perustuu hajaheijastukseen joko 700 nm tai 950 nm aallonpituudella ja sitä käytetään usein arvioitaessa keräyspaperista valmistetun massasuspension soveltuvuutta painopaperien valmistukseen ja painomusteen vaikutusta massan vaaleuteen. Mustepitoisuuden mittauksessa käytetään valonsirontakerrointa, joka voidaan mitata hieman läpikuultavasta näytteestä eli näytteen opasiteetin on oltava pienempi kuin 97 %. Tämä opasiteettiraja toteutuu useimmiten paperikoneella tehdyille painotuotteille. Riittävän alhainen opasiteetti saavutetaan myös valmistamalla standardin mukainen matalaneliömassainen arkki viiralle, mutta tämä johtaa kuitumaisten hienoaineiden, mineraalisten täyteaineiden ja painomusteiden alhaiseen retentioon. Matala retentio on erityisen haitallinen piirre mustemittauksen kannalta massoilla, jotka sisältävät huomattavia määriä painomusteita. Siten usein valmistetaan läpikuultamattomia arkkeja suodatinpaperin päälle, joiden retentio on korkea. Korkeasta opasiteetista johtuen näistä arkeista ei voida määrittää valonsirontakerrointa, jolloin mustepitoisuuden määritys perustuu vakiokertoimeen. Tämän väitöskirjan tavoitteena oli selvittää retention ja hienoaineiden muutoksien vaikutuksia valonsirontakertoimeen ja mustemittaustulokseen. Tutkimuksen tulokset osoittivat että valonsirontakerroin, joka mitataan mustepitoisuuden yhteydessä, ei pysy vakiona hienoainepitoisuuden muuttuessa. Hienoainepitoisuuteen ja siten valonsirontakertoimeen vaikuttavat keräyspaperin laji, hyperpesu ja vaahdotus. Myös painomuste vaikuttaa valonsirontakertoimeen, mutta käytännössä vaikutuksen suurusluokka on pienempi kuin hieno- ja täyteaineilla. Mustepitoisuuden määrityksessä käytetyn valonsirontakertoimen on oltava edustava, muutoin arvot voivat olla systemaattisesti virheellisiä hienoainemäärän tai laadun muuttuessa. Virheen välttämiseksi olisi suositeltavaa määrittää valonsirontakerroin mustepitoisuusanalyysin yhteydessä. Tämä olisi mahdollista tehdä suodatinpaperin päälle valmistetusta matalaneliömassaisesta arkista, jolloin saavutetaan korkea retentio ja näin mitattu arvo edustaa paremmin massasuspension alkuperäistä tilaa.

L'objectif de ce travail est d'étudier l'influence de l'état de dispersion de la silice sur les propriétés viscoélastiques et mécaniques des élastomères chargés silice pour l'application pneumatique. En effet, il est montré qu'une grande partie de la résistance au roulement dépend de la dissipation d'énergie de l'élastomère chargé. De plus, les propriétés mécaniques pourraient intervenir dans les propriétés ultimes telles la propagation de fissure en fatigue et l'usure : l'étude de ces différentes propriétés est donc primordiale. La première partie s'attèle donc à l'identification des leviers pouvant moduler la dispersion de la silice dans les élastomères. La dispersion pouvant être vue comme la compétition entre les forces de cohésion des charges et les forces appliquées au système pour les rompre, ces paramètres ont été étudiés de manière systématique. Enfin, l'influence des interactions silice-matrice est abordée (modification de l'état de surface de la silice, nature de l'élastomère) : le nombre d'interactions silice-élastomère par chaîne de polymère pourrait intervenir dans les mécanismes de dispersion. Dans la seconde partie, l'influence de ces différents états de dispersion sur les propriétés viscoélastiques et mécaniques est discutée. L'amélioration de la dispersion à iso-formulation permet de diminuer le module élastique linéaire dans le domaine linéaire et entraîne une augmentation des modules aux grandes déformations en traction. Concernant l'étude des propriétés ultimes, notre dispositif expérimental n'a pas permis de mettre en évidence, sur les formulations testées, d'influence de la dispersion sur la dynamique de propagation de fissure en fatigue. En revanche, l'amélioration de la dispersion entraîne une amélioration de la résistance à l'usure et ce malgré une diminution de la dureté / Filled elastomers are used in tread tires. It has been demonstrated that most of rolling resistance of tires is due to filled elastomer energy dissipation. In that way, understanding viscoelastic properties of these materials is a key point. Then, filled elastomer behavior at high deformations may be involved in ultimate properties of tire application such as fatigue crack propagation and wear. The aim of this work is to study the impact of silica dispersion on viscoelastic and mechanical properties of filled elastomers. First, levers impacting silica dispersion are evaluated. Dispersion of fillers can be considered as a competition between fillers cohesion forces and applied forces to the system to break them, these parameters have been studied methodically. Finally, the impact of silica-matrix interactions is studied, changing silica surface treatments or elastomer natures. The quantity of interactions possible per polymer chain between the silica and the elastomer may play a role in silica dispersion. Secondly, the impact of silica dispersion on viscoelastic and mechanical properties is discussed. It is shown than increasing silica dispersion leads to a decrease of linear elastic modulus and an increase of reinforcement in tensile at high deformations. Finally, regarding ultimate properties, our experimental device on the selected formulations has not shown any impact of silica dispersion on fatigue crack propagation. Nevertheless, we observe a better wear resistance with increasing dispersion, despite the lower materials hardness

In the world there are adverse climates, climates that hinder the good construction and paving of roads, generating insecurity among the locals and visitors. This over time affects the economy of a country, as a road boosts tourism, transport and commerce. Therefore, a mixture was designed to mitigate a problem in the placement of hot asphalt mixture at temperatures below zero degrees Celsius. That is, a conventional mix design was proposed, but with different types of filler (lime, Portland cement type I and silica) tested with the Marshall and Lottman method which are governed according to the EG-2013 standards [1] and parameters established in the Asphalt Institute [2]. To find the optimum, it was tested with 5.0%, 5.5% 6.0% and 6.5% asphalt cement. Then with the results obtained a comparative analysis was performed. Finally, specimens without any additives were made, the specimens once prepared at 140°C were subjected to freezing, resulting in the three types of filler, that the hot asphalt mixture with incorporation of Portland cement type I to a 5, 90% of asphalt cement is the optimum since, subject to extreme temperatures below 0°C they comply with the parameters required in the standards.

Aim of magister´s thesis was to study reaction kinetics of dental materials. Thesis was focused on dimethacrylate dental polymers, which are for example used for dental restoration, tooth repair and creating now teeth. First part of the thesis concentrates on influence of molar ratio on reation kinetics by addition of other monomer to polymer resin. Second part concentrates on influence of addition of additive silica on reaction kinetics of polymerization. Essential variables know as a polymerization ratio, conversion, gel point, glass transition temperature and storage modulus were studied. Firstly, polymerization ratio and conversion were observed by differential scanning calorimetry (DSC). Secondly rheology was observed by photoreometr. Finally, glass transition temperature and storage modulus were observed by dynamic mechanical analysis (DMA). Behaviour changes caused by addion of monomer or filler point out decrease of polymeration ratio and converstion. Same behaviour was observed by short exposure. In order to established network formation, values of gel point increased by higher concentration of monomer or filler. Glass transition temperature and storage modulus measured by DMA were evaluated. Those valuables had variable tendency due to monomer acting like filler at higher concentration. Also contradictory impact of different material conversion and filler concetration was discussed.

The diploma thesis deals with study of system of polypropylene and inorganic filler. As filler was used commercially available particulate filler CaCO3 termed NPCC 201. The objective of the study was a surface plasma treatment of filler in order to obtain composite based on polypropylene. Mechanical properties of this composite will show significantly greater value than basic matrix. The filler was treated in dielectric barrier plasma discharge by atmospheric pressure. The characterization of filler was performed before and after plasma treatment by x-ray photoelectron spectroscopy (XPS), electron microscope (SEM) and sedimentation analysis. The distribution of particle size was measured by laser diffraction and by dynamic light scattering. The composite materials with various weight concentration of filler were prepared in POLYMER INSTITUTE BRNO by using the twin-screw extruder and the test specimens were prepared by the injection molding technology. Their mechanical properties was studied by using of short and long-term tests. The uniaxial creep testing in tension was used for study of long-term behavior of composites.

The work deals with the development of a new thermal insulation material that contains a secondary raw materials or waste. It is an insulating material with the requirement of resistance to high temperatures - 200 ° C and 500 ° C. Type of material is determined by the way of reducing density - direct and indirect. Direct is achieved by adding lightweight aggregates, indirect is achieved by gas evolution through chemical reaction and the subsequent incorporation of gas into the structure of the material. This thesis is part of the MPO TIP č. FR-TI 2/340 project.

This master thesis focus on the analysis of effects that cause defects in concrete blocks. Experiences show that the defect of the blocks are often manifested in the form of cracks. Great rate of occurrence of defects is attributed to volume changes of poor quality concrete filler. The aim of this master thesis is to analyze the finding from the practical use and exploration of the requirements for the actual blocks and especially the concrete filler which is used to make monolithic structures built from these blocks. The attention will be paid to the interaction between the block and the concrete filler. Here we focus mainly on the volume changes caused by a change of moisture level and especially the cyclic moisture.