The main aim of the thesis is to evaluete properties of a simplified thermal calculation of the direct fired heater published in the journal Applied Energy at 2010 and its application to specific industrial cases. At first, general issues of process heaters are talk over. Second, calculation model in cited article is briefly introduced. After that, custom computational model at program Maple is created in accordance with published article. Subsequently, the model is applied to the existing process furnaces in the form of a check calculation. An integral part of the work is also a detailed discussion of the results obtained.

Energy mix modellers often use a constant emissions factor model, which more or less implies a constant heat rate, when trying to show the emissions reduction benefits of integrating renewable power generation system on the grid. This approach does not consider the fact that there is a deterioration in the heat rate with load for the Coal Fired Power Plants that need to accommodate the additional renewable supply. If varying heat rate were to be included in a study, it is often limited to plant specific cases. This PhD presents a novel Variable Turbine Cycle Heat Rate (V-TCHR) model for predicting the part load Turbine cycle heat rate (TCHR) response of various Coal Fired Power Plant (CFPP) architectures, without detail knowledge of the entire steam cycle parameters. A total of 192 process models of representative CFPP architectures were developed using a Virtual Plant software. The models had different combinations of the degree of reheat; the throttle temperature; throttle pressure; and condenser cooling technology. The part load response of all the models were simulated using the software.

L’argile est une ressource locale, abondante mais peu valorisée au Bénin. Le recyclage des déchets constitue de nos jours, un enjeu majeur au niveau mondial. Les briques d’argile cuite sont des matériaux à fort tonnage de production capables d’absorber différents produits considérés comme des déchets. Cette thèse vise d’une part la valorisation des matériaux de construction localement disponibles au Bénin, notamment l’argile et d’autre part, le recyclage des déchets en construction. Ainsi, nous nous proposons de valoriser des bouteilles en verre non recyclés et des cendres issues de la combustion du charbon de bois lors de la préparation des repas au Bénin, dans la matrice argileuse destinée à l’élaboration de briques cuites. Le but est de ressortir les formulations idéales des produits qui présentent des propriétés physiques et mécaniques suffisantes. Les études ont montré que le dosage de 5% des cendres de bois du Bénin et 20% de verres broyés favorise un gain de résistance à la traction par flexion trois points sans modifier la résistance à la compression des blocs d’argile cuits de Zogbodomey et de Sèmè-Podji. En outre, le dosage en ajout ne modifie pas les propriétés thermiques des blocs cuits. L’utilisation des cendres de charbon de bois et des déchets de verre comme matières premières secondaires dans la fabrication de briques cuites constitue alors un grand atout pour l’amélioration du cadre de vie des béninois. / Clay is a local resource, abundant but little valued in Benin. Waste recycling is nowadays a major issue at the global level. The fired clay bricks are high production tonnage materials capable of absorbing different products considered as waste. This thesis aims on the one hand the valuation of building materials locally available in Benin, including clay and secondly, the recycling of waste under construction. Thus, we propose to valorize nonrecycled glass bottles and ashes from the burning of charcoal during the preparation of meals in Benin, in the clay matrix for the preparation of cooked bricks. The goal is to highlight the ideal formulations of products that have sufficient physical and mechanical properties. Studies have shown that the 5% Benin wood ashes content and 20% crushed glass content increase the tensile strength by three-point bending without modifying the compressive strength of the Zogbodomey fired clay blocks from Seme-Podji. In addition, the addition dosage does not modify the thermal properties of the fired blocks. The use of wood ashes and glass waste as a secondary raw material in the manufacture of fired bricks is an effective alternative to land and environmental conservation, and it can be a sustainable and cost-effective solution for the building industry. These materials are then a great asset for improving the living environment in Benin.

Due to the power requirements for today's microprocessors, point of load converter packaging is becoming an important issue.   Traditional thermal management techniques involved in removing heat from a printed circuit board are being tested as today's technologies require small footprint and volume from all electrical systems.  While heat sinks are traditionally used to spread heat, ceramic substrates are gaining in popularity for their superior thermal qualities which can dissipate heat without the use of a heat sink.  3D integration techniques are needed to realize a solution that incorporates the active and components together.  The objective of this research is to explore the packaging of a high current, high power density, high frequency DC/DC converter using ceramic substrates to create a low profile converter to meet the needs of current technologies. One issue with current converters is the large volume of the passive components.  Increasing the switching frequency to the megahertz range is one way to reduce to volume of these components.  The other way is to fundamentally change the way these inductors are designed.  This work will explore the use of low temperature co-fired ceramic (LTCC) tapes in the magnetic design to allow a low profile planar inductor to be used as a substrate.  LTCC tapes have excellent properties in the 1-10 MHz range that allow for a high permeability, low loss solution.  These tapes are co-fired with a silver paste as the conductor.  This paper looks at ways to reduce dc resistance in the inductor design through packaging methods which in turn allow for higher current operation and better heavy load efficiency.  Fundamental limits for LTCC technologies are pushed past their limits during this work.  This work also explores fabrication of LTCC inductors using two theoretical ideas: vertical flux and lateral flux.  Issues are presented and methods are conceived for both types of designs.  The lateral flux inductor gives much better inductance density which results in a much thinner design. It is found that the active devices must be shielded from the magnetic substrate interference so active layer designs are discussed.  Alumina and Aluminum Nitride substrates are used to form a complete 3D integration scheme that gives excellent thermal management even in natural convection.  This work discusses the use of a stacked power technique which embeds the devices in the substrate to give double sided cooling capabilities.  This fabrication goes away from traditional photoresist and solder-masking techniques and simplifies the entire process so that it can be transferred to industry.  Time consuming sputtering and electroplating processes are removed and replaced by a direct bonded copper substrate which can have up to 8 mil thick copper layers allowing for even greater thermal capability in the substrate.  The result is small footprint and volume with a power density 3X greater than any commercial product with comparable output currents.  A two phase coupled inductor version using stacked power is also presented to achieve even higher power density. As better device technologies come to the marketplace, higher power density designs can be achieved.  This paper will introduce a 3D integration design that includes the use of Gallium Nitride devices.  Gallium Nitride is rapidly becoming the popular device for high frequency designs due to its high electron mobility properties compared to silicon.  This allows for lower switching losses and thus better thermal characteristics at high frequency.  The knowledge learned from the stacked power processes gives insight into creating a small footprint, high current ceramic substrate design.  A 3D integrated design is presented using GaN devices along with a lateral flux inductor.  Shielded and Non-Shielded power loop designs are compared to show the effect on overall converter efficiency.  Thermal designs and comparisons to PCB are made using thermal imaging.  The result is a footprint reduction of 40% from previous designs and power densities reaching close to 900W/in3. / Master of Science

No description available.

The objective of this study is to investigate the eect of dierent fuels on two uidized bed boiler systemsat the energy company Soderenergi's site in Igelsta, called IKV and IGV P3. Today, recovered wastewood (RWW) is the major fuel share fed into the boilers. However, with an insecure fuel supply in thefuture, other fuel types must be considered. Based on knowledge from previous fuel usage in the boilers,an evaluation of how other potential fuel mixtures may eect the operation is conducted. The additionalfuels considered in the fuel blends are; stem wood chips, cutter shavings, solid recycled fuel (SRF) andrubber.With elemental analysis of the fuels and established key numbers, the previous fuel mixtures are evaluated.The indications by the guiding parameters are compared with experienced problems and the formercondition of the boilers, and the risk limits for the key numbers are adjusted to a suitable level. Thepotential mixtures are evaluated with the key numbers and the updated limits. In addition to the keynumbers, the heavy metal concentration, the heating value, the moisture content and the ash content ofthe fuel blends are included in the evaluation. The considered damages in the boilers caused by the fuelblends are corrosion, sintering and fouling.The damage level from the current fuel usage for IKV and IGV P3 is fairly low. The results from theanalyzed fuel mixtures show an increased damage risk in the boilers. Additionally, adjustments of theboiler systems are required by some of the analyzed fuel mixtures. In general, the corrosion risk andthe heavy metal content will increase in comparison with today's fuel. The fouling and slagging are aswell expected to increase for the assessed fuel mixtures. Moreover, the result illustrates an increased ashgeneration, which demands a reconstruction of the ash cooling system for IKV. Furthermore, the increaseof LHV in the assessed fuel mixtures to IGV P3, is likely to require an increased capacity of the ue gasrecirculation pump.In the analysis of the potential fuel mixtures it is found that the corrosion risk expressed by the keynumbers is reduced with a higher share of rubber. The heavy metal content is, however, increased,leading to e.g. an enhanced risk for formation of eutectic salts, which as well are corrosive. On thecontrary, the fuel mixtures with a high risk expressed by the key numbers, have the lowest concentrationsof heavy metals. Due to the results are con icting, a balance between the risk indicated by the keynumbers and the heavy metal concentration must be considered in the evaluation. The fuel mixturesconsidered causing least damage to IKV are a mixture of 42% RWW, 48% wood fuel and 15% SRF, and amixture of 70% wood fuel, 20% SRF and 10% rubber. The fuel mixtures considered causing least damageto IGV P3 are a mixture of 85% RWW and 15% rubber and a mixture of 70% RWW and 30% SRF. / Syftet med studien var att undersoka branslets paverkan pa tva uidbaddpannor, IKV och IGV P3, hos energiforetaget Soderenergi. Idag ar det huvudsakliga branslet i dessa pannor returtra (RT). Med en standigtrorlig branslemarknad kravs kunskap av alternativa branslen. Baserat pa tidigare bransleanvandning,har paverkan fran potentiella bransleblandningar pa pannan undersokts. Utover returtra ar stamveds is,span, papper-plast-tra (SRF) och gummi med i de analyserade blandningarna.Med elementaranalyser pa branslen och etablerade nyckeltal utvarderades de tidigare anvanda branslena.Indikationen fran nyckeltalen ar jamford med upplevda problem och risknivaerna for nyckeltalen arandrade till passande nivaer. De framtida bransleblandningarna analyserades med hjalp av nyckeltalenoch de uppdaterade risknivaerna. Utover nyckeltalen analyserades tungmetallhalten, varmevardet, fukthaltenoch askhalten i bransleblandningarna. De pannskador orsakade av bransleblandningarna somundersokts ar korrosion, sintring och paslag.Det nuvarande branslet till IKV och IGV P3 ger en relativt lag skadeniva. Resultaten fran de analyseradebransleblandningarna visar att skaderisken i pannorna kommer att oka och forandringar av pannan kankomma att kravas. Generellt kommer korrosionsrisken och tungmetallinnehallet att oka i jamforelse meddagens bransle. Okat paslag och slaggning ar ocksa forvantat. Vidare visar resultatet att askproduktionenkommer att oka, vilket gor att IKVs kylsystem for bottenaskan kommer behovas byggas ut. LHV for deanalyserade bransleblandningarna for IGV P3 okar, vilket innebar att kapaciteten for returgas aktarnatroligen maste okas.I jamforelsen av de olika bransleblandningarna visas att korrosionsrisken, forutspadd av nyckeltalen,minskar med en hogre andel gummi. Daremot okar tungmetallinnehallet, vilket leder till en okad riskfor bildning av eutektiska salter, vilka ocksa ar korrosiva. Bransleblandningarna med en indikerad hogrisk av nyckeltalen, har tvartemot den lagsta koncentrationen av tungmetaller. Eftersom resultatenar motsagande, kravs en avvagning mellan riskerna indikerade av nyckeltalen och tungmetallshalten.De bransleblandningar som ar ansedda att vara minst skadliga for IKV ar en blandning av 42% RT,48% tradbransle och 15% SRF, och en blandning av 70% tradbransle, 20% SRF och 10% gummi. Debransleblandning som ar ansedda att vara minst skadliga for IGV P3 ar en blandning av 85% RT och15% gummi, och en blandning av 70% RT och 30% SRF.

På grund av det stundande ökade elektricitetsbehovet vill Växjö Energi AB utreda möjligheter för utökad kapacitet för elektricitetsproduktion i samband med att ett av deras befintliga kraftvärmeblock börjar nå sin livslängd. En av de tekniker som Växjö Energi, genom detta examensarbete, granskar är Biomass fired Top Cycle. Denna teknik står företaget Phoenix BioPower AB för, där tekniken är specifikt inriktad på att kunna få ut ett högre elutbyte än vad befintliga kraftvärmeverk kan idag. Genom två olika scenarion, där ett Biomass fired Top Cycle block ingår, jämför arbetet bränsleförbrukning, värme- och elproduktion emot VEAB:s befintliga anläggning under ett år. I Scenario 1 var BTC-blocket i drift självt under sommarperioden, medan det i scenario 2 var avstängt och SV3 istället var i drift. Resultatet för de två scenariona visade på en stor ökning för elektricitetsproduktionen, men också en ökning för bränsleförbrukningen. Utifrån elektricitetsproduktionen och bränsleförbrukningen analyserades intäkter och kostnader för ett exempel år 2022. Arbetet konstaterar att välja mellan hög elektricitetsproduktion alternativt hög bränsleförbrukning är en komplex fråga, där både faktorer så som tillgänglighet på biomassa och världens energiläge läggs till.

No description available.

Today, every microprocessor is powered with a Voltage Regulator (VR), which is also known as a high current Point-of-Load converter (POL). These circuits are mostly constructed using discrete components, and populated on the motherboard. With this solution, the passive components such as inductors and capacitors are bulky. They occupy a considerable footprint on the motherboard. The problem is exacerbated with the current trend of reducing the size of all forms of portable computing equipment from laptop to netbook, increasing functionalities of PDA and smart phones. In order to solve this problem, a high power density POL needs to be developed. An integration solution was recently proposed to incorporate passive components, especially magnetic components, with active components in order to realize the needed power density for the POL. Today's discrete VR only has around 100W/in3 power density. The 3D integration concept is widely used for low current integrated POL. With this solution, a very low profile planar inductor is built as a substrate for the active components of the POL. By doing so, the POL footprint can be dramatically saved, and the available space is also fully utilized. This 3D integrated POL can achieve 300-1000W/in3 power density, however, with considerably less current. This might address the needs of small hand-held equipment such as PDA and Smart phone type of applications. It does not, however, meet the needs for such applications as netbook, laptop, desk-top and server applications where tens and hundreds of amperes are needed. So, although the high density integrated POL has been demonstrated at low current level, magnetic integration is still one of the toughest barriers for integration, especially for high current POL. In order to alleviate the intense thirst from the computing and telecom industry for high power density POL, the 3D integration concept needs be extended from low current applications to high current applications. The key technology for 3D integration is the low profile planar inductor design. Before this research, there was no general methodology to analyze and design a low profile planar inductor due to its non-uniform flux distribution, which is totally different as a conventional bulky inductor. A Low Temperature Co-fired Ceramic (LTCC) inductor is one of the most promising candidates for 3D integration for high current applications. For the LTCC inductor, besides the non-uniform flux, it also has non-linear permeability, which makes this problem even more complicated. This research focuses on penetrating modeling and design barriers for planar magnetic to develop high current 3D integrated POL with a power density dramatically higher than today's industry products in the same current level. In the beginning, a general analysis method is proposed to classify different low profile inductor structures into two types according to their flux path pattern. One is a vertical flux type; another one is a lateral flux type. The vertical flux type means that the magnetic flux path plane is perpendicular with the substrate. The lateral flux type means that the magnetic flux path plane is parallel with the substrate. This analysis method allows us to compare different inductor structures in a more general way to reveal the essential difference between them. After a very thorough study, it shows that a lateral flux structure is superior to a vertical flux structure for low profile high current inductor design from an inductance density point of view, which contradicts conventional thinking. This conclusion is not only valid for the LTCC planar inductor, which has very non-linear permeability, but is also valid for the planar inductor with other core material, which has constant permeability. Next, some inductance and loss models for a planar lateral flux inductor with a non-uniform flux are also developed. With the help of these models, different LTCC lateral flux inductor structures (single-turn structure and multi-turn structures) are compared systematically. In this comparison, the inductance density, winding loss and core loss are all considered. The proposed modeling methodology is a valuable extension of previous uniform flux inductor modeling, and can be used to solve other modeling problems, such as non-uniform flux transformer modeling. After that, a design method is proposed for the LTCC lateral flux inductor with non-uniform flux distribution. In this design method, inductor volume, core thickness, winding loss, core loss are all considered, which has not been achieved in previous conventional inductor design methods. With the help of this design method, the LTCC lateral flux inductor can be optimized to achieve small volume, small loss and low profile at the same time. Several LTCC inductor substrates are also designed and fabricated for the 3D integrated POL. Comparing the vertical flux inductor substrate with the lateral flux inductor substrate, we can see a savings of 30% on the footprint, and a much simpler fabrication process. A 1.5MHz, 5V to 1.2V, 15A 3D integrated POL converter with LTCC lateral flux inductor substrate is demonstrated with 300W/in3 power density, which has a factor of 3 improvements when compared to today's industry products. Furthermore, the LTCC lateral flux coupled inductor is proposed to further increase power density of the 3D integrated POL converter. Due to the DC flux cancelling effect, the size of LTCC planar coupled inductor can be dramatically reduced to only 50% of the LTCC planar non-coupled inductor. Compared to previous vertical flux coupled inductor prototypes, a lateral flux coupled inductor prototype is demonstrated to have a 50% core thickness reduction. A 1.5MHz, 5V to 1.2V, 40A 3D integrated POL converter with LTCC lateral flux coupled inductor substrate is demonstrated with 700W/in3 power density, which has a factor of 7 improvements when compared to today's industry POL products in the same current level. In conclusion, this research not only overcame some major academia problems about analysis and design for planar magnetic components, but also made significant contributions to the industry by successfully scaling the integrated POL from today's 1W-5W case to a 40W case. This level of integration would significantly save the cost, and valuable motherboard real estate for other critical functions, which may enable the next technological innovation for the whole computing and telecom industry. / Ph. D.

No description available.