Spelling suggestions: "subject:"flipchip"" "subject:"flipchart""
91 |
Exploration of liquid crystal polymer packaging techniques for rf wireless systemsPatterson, Chad E. 03 July 2012 (has links)
In the past decade, there has been an increased interest in low-cost, low-power, high data rate wireless systems for both commercial and defense applications. Some of these include air defense systems, remote sensing radars, and communication systems that are used for unmanned aerial vehicles, ground vehicles, and even the individual consumer. All of these applications require state-of-the-art technologies to push the limits on several design factors such as functionality, weight, size, conformity, and performance while remaining cost effective. There are several potential solutions to accomplish these objectives and a highly pursued path is through the utilization of advanced integrated system platforms with high frequency, versatile, multilayered materials.
This work intends to explore advanced 3-D integration for state-of the art components in wireless systems using LCP multilayer organic platforms. Several packaging techniques are discussed that utilize the inherent benefits of this material. Wire bond, via interconnect, and flip-chip packages are implemented at RF and millimeter-wave (mm-wave) frequencies to explore the benefits of each in terms of convenience, reliability, cost, and performance. These techniques are then utilized for the demonstration of bulk acoustic waveguide (BAW) filter applications and for the realization of highly integrated phased-array antenna systems.
|
92 |
Experimental and theoretical study of on-chip back-end-of-line (BEOL) stack fracture during flip-chip reflow assemblyRaghavan, Sathyanarayanan 07 January 2016 (has links)
With continued feature size reduction in microelectronics and with more than a billion transistors on a single integrated circuit (IC), on-chip interconnection has become a challenge in terms of processing-, electrical-, thermal-, and mechanical perspective. Today’s high-performance ICs have on-chip back-end-of-line (BEOL) layers that consist of copper traces and vias interspersed with low-k dielectric materials. These layers have thicknesses in the range of 100 nm near the transistors and 1000 nm away from the transistors close to the solder bumps. In such BEOL layered stacks, cracking and/or delamination is a common failure mode due to the low mechanical and adhesive strength of the dielectric materials as well as due to high thermally-induced stresses. However, there are no available cohesive zone models and parameters to study such interfacial cracks in sub-micron thick microelectronic layers.
This work focuses on developing framework based on cohesive zone modeling approach to study interfacial delamination in sub-micron thick layers. Such a framework is then successfully applied to predict microelectronic device reliability. As intentionally creating pre-fabricated cracks in such interfaces is difficult, this work examines a combination of four-point bend and double-cantilever beam tests to create initial cracks and to develop cohesive zone parameters over a range of mode-mixity. Similarly, a combination of four-point bend and end-notch flexure tests is used to cover additional range of mode-mixity. In these tests, silicon wafers obtained from wafer foundry are used for experimental characterization. The developed parameters are then used in actual microelectronic device to predict the onset and propagation of crack, and the results from such predictions are successfully validated with experimental data. In addition, nanoindenter-based shear test technique designed specifically for this study is demonstrated. The new test technique can address different mode mixities compared to the other interfacial fracture characterization tests, is sensitive to capture the change in fracture parameter due to changes in local trace pattern variations around the vicinity of bump and the test mimics the forces experienced by the bump during flip-chip assembly reflow process. Through this experimental and theoretical modeling research, guidelines are also developed for the reliable design of BEOL stacks for current and next-generation microelectronic devices.
|
93 |
Development of lightweight and low-cost microwave components for remote-sensing applicationsDonado Morcillo, Carlos Alberto 11 January 2013 (has links)
The objective of the proposed research is to design, implement, and characterize low-cost, lightweight front-end components and subsystems in the microwave domain through innovative packaging architectures for remote sensing applications. Particular emphasis is placed on system-on-package (SoP) solutions implemented in organic substrates as a low-cost alternative to conventional, expensive, rigid, and fragile radio- frequency substrates. To this end, the dielectric properties of organic substrates RT/duroid 5880, 6002 and 6202 are presented from 30 GHz to 70 GHz, covering most of the Ka and V radar bands, giving also a thorough insight on the uncertainty of the microstrip ring resonator method by means of the Monte Carlo uncertainty analysis.
Additionally, an ultra-thin, high-power antenna-array technology, with transmit/ receive (T/R) functionality is introduced for mobile applications in the X band. Two lightweight SoP T/R array panels are presented in this work using novel technologies such as Silicon Germanium integrated circuits and microelectromechanical system switches on a hybrid organic package of liquid crystal polymer and RT/duroid 5880LZ. A maximum power of 47 dBm is achieved in a package with a thickness of 1.8 mm without the need of bulky thermal management devices.
Finally, to address the thermal limitations of thin-film substrates of interest (liquid crystal polymer, RT/duroid 6002, alumina and Aluminum Nitride), a thermal assessment of microstrip structures is presented in the X band, along with the thermal characterization of the dielectric properties of RT/duroid 6002 from 20 C to 200 C and from 30 GHz to 70 GHz. Additional high-power, X-band technologies presented in this work include: a novel and compact topology for evanescent mode filters, and low-profile Wilkinson power dividers implemented on Aluminum Nitride using Tantalum Nitride thin-film resistors.
|
Page generated in 0.0349 seconds