The aim of the thesis has been to evaluate and understand the effect of caustic alkali solution of varying composition on the behaviour of expansive soil containing mixed layered minerals. Mixed layered minerals are formed of two or more kinds of inter grown layers, not physical mixtures. Illite - smectite is the most abundant and wide spread of the mixed layered clay minerals in sedimentary rocks and soils and also more common than either discrete illite or smectite. In geotechnical engineering much attention has not been paid to the behaviour of soils containing mixed layered minerals. Much less is known about the behaviour of these soils in polluted environment. Mixed layered minerals are more susceptible to environmental changes as the structural linkages between the layer minerals are weak compared to normal layered phyllosilicates. One important pollutant that can have considerable effect on the behaviour of soils is the caustic alkali contamination released from various industries. Recent studies have shown that the behaviour of even stable minerals is affected by alkali contamination. However, the effect of caustic alkali contamination on the behaviour of soils containing mixed layered minerals is not known and has been chosen for detailed study. Also to understand the mechanism of their interaction with alkali, it is necessary to study the effect of alkali solutions on the constituent clay minerals viz., montmorillonite and illite under similar conditions. To elucidate the mechanism of soil alkali interaction limited tests were conducted with simple electrolyte solution, as the alkali solution also acts as electrolyte apart from being alkaline. To confirm the mechanism of interaction, tests are also conducted on these soils with industrial spent liquor containing high caustic alkali and suspended alumina obtained from an alumina extraction plant treating bauxite with high alkali solutions at high temperatures. The results obtained in the laboratory are compared with the soil samples contaminated with leaking industrial Bayer's liquid in the field. Studies are also conducted to suggest remedial measures to control the adverse effects of alkali solutions on soil containing mixed layer minerals. The content of the thesis is broadly divide into 8 Chapters - viz., Introduction, Background and overview, Experimental program and procedures, Behaviour of soils containing mixed layer mineral illite - smectite (BCSI), Behaviour of montmorillonite and illite, Influence of Bayer's liquor and study on the field contaminated soils, Measures to control the influence of alkali contamination on BCSI and Summary and conclusions. The broad outline of these chapters is given in Chapter 1. A review of literature on the behaviour of soils containing different types of clay minerals with emphasis on mixed layer minerals has been presented in Chapter 2. The influence of different inorganic contaminants on the properties of soils in terms of their physical and chemical characteristics as well as their concentration has been summarized. The importance of changes in surface characteristics of soil particles and the changes in the thickness of diffuse double layer in altering the property of soils at low concentration of contaminants and changes in the mineralogy with high concentrated contaminants such as acids and alkalis has been highlighted. This forms the background information necessary to bring out the scope of the study. Four soils having different mineralogy have been used in this study. These soils are, black cotton soil containing predominantly mixed layer mineral illite - smectite mineral called rectorite, illite, montmorillonite (common smectite) and black cotton soil containing predominantly montmorillonite. The properties of the soils used are described in Chapter 3. Caustic alkali solutions of 1N, 4N concentration prepared in the laboratory and industrial alkali-spent liquor are used as contaminants. The spent Bayer's liquor had about 4N alkali concentration and 10% alumina in suspension. To simulate the effect of suspended alumina, two more caustic alkali solutions of 1N and 4N solutions containing 10% alumina by weight of solutions are also prepared. To isolate the effect of electrolyte solutions from that of alkali solution, two electrolyte solutions of 1N and 4N sodium chloride solutions are also used. Test procedures for conducting various tests such as pH, water adsorption characteristics, X-ray diffraction studies, SEM studies, thermal characteristics and geotechnical properties such as Atterberg limits, Oedometer tests and Shear Strength are given in this chapter. The test procedures are modified, wherever necessary, to bring out the effect of contaminants, particularly the effect of duration of interaction on the properties of soils. The source and properties of black cotton soil are presented in Chapter 4. Detailed x-diffraction studies have confirmed the presence of inter layered illite-smectite mineral viz., rectorite, which is uncommon in Indian expansive soils, and is classified as CH (Clay of high compressibility) as per ASTM soil classification. Effect of alkali and salt solutions of 1N and 4N concentration on all physico chemical and geotechnical properties are studied in this chapter. As it is known that presence of certain elements such as aluminium influence the soil alkali interaction, the effect of suspended alumina along with alkali solution has also been investigated. The effect of contaminating fluids such as 1N NaOH, 4N NaOH with and without alumina, 1N NaCl and 4N NaCl on the geotechnical properties of the soil has been studied. Mineralogical changes were observed by XRD and thermal studies in the soil treated with 4N NaOH solution and 4N NaOH + 10% alumina. The interlayer potassium of illite is released and potassium hydroxide is formed in soil treated with 4N NaOH. Swelling compounds such as sodium aluminium silicate hydroxide hydrate (SASH) has formed due to attack of 4N NaOH + 10% alumina on silica rather than on rectorite. Thus the studies clearly bring out that the rectorite present in the soil is dissociated only in the presence of strong alkali solutions of concentration of about 4N. The liquid limit of soil decreased with increase in the electrolyte concentration in the case of NaCl solutions. With 1N NaOH, the liquid limit of soil increased due to increase in the thickness of diffuse double layer due to increased pH. However, Proctor's maximum dry density increased and optimum moisture content decreased with 1N NaOH. With increase in the concentration of alkali solution to 4N, the rectorite dissociates into constituent minerals with the formation potassium hydroxide. The liquid limit of soil decreased probably due to the dominating influence of electrolyte nature of hydroxide solution over the effect of increased negative charge on clay particles due increase in the pH on the constituent minerals. Proctor's maximum dry density decreased and optimum moisture content increased with 4N NaOH. Sediment volume and oedometer free swell at seating/nominal surcharge load of 6.25 kPa of soil increased in 1N and 4N caustic alkali solutions, though by different mechanisms. The increase with 1N solution is essentially due to increased negative charges on clay mineral surface. However, the increase in swelling with 4N solution is associated with the dissociation of rectorite mineral and occurs in two distinct phases unlike in the case of 1N solution. While the first phase can be attributed to the effect of alkaline nature of the solution after reduction in its concentration due to reaction with rectorite and the consequent reduction in its electrolyte nature. The second phase is due to the swelling of the separated constituent minerals in the presence of excess of alkali and occurs after much delay. Consolidation behaviour of rectorite in 1N and 4N alkali solutions has been studied in two ways: 1). Loading without waiting for the second stage of swelling to occur, as in standard consolidation procedure and 2). Loading after completion of second stage of swelling which is occurring after considerable delay as explained earlier. Normally one would initiate loading after equilibrium is reached at the end of first stage of swelling and second stage of swelling is not suspected. As there is no second stage of swelling with 1N solutions, these two types of consolidation tests produced the same results. Abnormal rebound is observed during unloading with 4N solution in which loading cycle is initiated without waiting for second stage of swelling to complete. It is interesting to note that while the liquid limit of soil decreased with increase in the concentration of alkali solution, the swelling increased. The testing procedure and period of interaction as well as the concentration of alkali solution during the test in these two tests are different. The effects of alkali solution are more severe in case of liquid limit because of thorough mixing and consequent effective reaction during testing. Similarly, the volume changes in soil that has already reacted with 4N alkali solution when exposed to further to alkali contamination are considerably less compared to uncontaminated soil exposed to fresh contamination. The shear strength of soil treated with 4N-alkali solution has increased particularly after long period of interaction. This indicates that the soil after mineralogical changes posses good strength. Chapter 5 presents the effect of alkali and salt solutions on the physico chemical and geotechnical properties of component minerals of mixed layered illite/smectite. For this study, commercially obtained montmorillonite (bentonite), naturally occurring black soil containing montmorillonite and commercially pure illite are used. It was observed that montmorillonite alkali reactions would not produce significant mineralogical changes where as illite is dissociated into smectite with the formation of potassium silicate by the interaction of released potassium with soluble silica. This confirms that the ultimate products of rectorite with alkali solutions would be smectite and compounds of potassium. In the absence of mineralogical alterations the liquid limit of montmorillonite decreases due to suppression of diffuse double layer thickness due to dominating influence of alkali solutions on this highly active clay. However a small increase in liquid limit is observed in illite with alkali solutions. Thus the net effect of alkali on rectorite is to decrease the liquid limit with increase in alkali concentration. While the free swell and oedometer swelling of montmorillonite generally decreases with increase in the alkali concentration, they increase in illite. However, in both the minerals the swelling occurs only in one phase. Thus the second phase of swelling that has been observed in rectorite can be attributed to delayed swelling of montmorillonite that has been released by the attack of alkali on rectorite. The behaviour of black soil containing mixed layer mineral contaminated in the field and laboratory by leaking Bayer's spent liquor in an alumina extraction plant has been studied in Chapter 6. The Atterberg limits of the samples treated with liquor are reduced and sediment volume increased. Similarly the swelling at seating load in consolidation test is higher in sample compacted with water and inundated with liquor. X-ray diffraction studies showed that the mineralogical changes are similar to those occurred with 4N caustic alkali solution. The mineralogical and micro structural changes in the soil samples that are contaminated by leaked spent liquor in the field are relatively more marked. Also the behavior of highly montmorillonite clay, bentonite, has been studied contaminated with liquor in the laboratory. The study on the effect of high concentrated alkali solutions on montmorillonite can be useful to study the effect of interaction on the dissociated montmorillonite. These studies are helpful to suggest some possible remedial measures to control the adverse effect of alkali on soils. Possible Remedial schemes that can be adopted before and after contamination of the soil to control the adverse effect of alkali solutions on the black cotton soil containing mixed layered mineral are listed and their effectiveness examined in Chapter 7. The suggested remedial measures include flushing with water to dilute the effect of alkali, neutralisation with dilute hydrochloric acid, stabilisation of soil with lime and calcium chloride and use of impervious membrane to separate the foundation soil from alkali solution. The effectiveness of different measures as well as the method of their application has been described. Efforts are made to understand the mechanism of remedial action. Consolidation tests conducted on soil contaminated with 4N alkali solution and inundated with water showed increased swelling due to dilution of the alkali concentration. Though the swelling of contaminated soil can be controlled by passing dilute hydrochloric acid (1N), the method is not advocated as it can lead to ground water contamination. Mixing the soil with solutions containing up to 5% by weight of calcium compound in water could not prevent the alkali induced heave in the long run when inundated with 4N alkali solution. This was due to dissolution of silica by the strong alkali solutions and formation of swelling compounds such as sodium aluminium silicate hydroxide hydrate (SASH). The formation of sodium aluminates occurred only when the alkali solution contained alumina or soil contained calcium compounds. There are no significant variations in the effects of calcium chloride or calcium hydroxide on contaminated soil. Replacing the foundation soil with soil thoroughly contaminated with 4N alkali solutions and controlling the migration of contaminants into the foundation soil using high-density polyethylene (HDPE) geosynthetic membranes can be an effective measure to control the heaving in alkali contaminated foundation soil containing interstratified illite – smectite. Summary and the major conclusions of the thesis are presented in Chapter 8.

Sub-surface soil pollution by various processes with high concentration of contaminants can significantly alter geotechnical properties of soils causing unexpected failures of structures founded on them. The changes can occur due to alteration in soil water interaction processes and/or by intense chemical interactions leading to mineralogical and microstructural changes. Behaviour of soil upon contamination with alkali pollutant is one of the major concerns faced by the geotechnical researchers in recent years. In the present study an attempt has been made to understand the role of mineralogical and morphological changes on the volume change (swelling and compressibility) behaviour of soils by prolonged interaction with caustic alkali pollutant. Based on the results it has been proposed to develop remedial measures to nullify and/or control the detrimental effects. A comprehensive experimental program has been planned to achieve these objectives. The experimental investigations carried out and results obtained are presented in eight chapters as follows. The broad outline of thesis is given in Chapter 1. A detailed review of literature on the type of phyllosilicate minerals present in various soils is presented in Chapter 2 with a view to select most common soils for the study. Various sources of contaminants and their effect on the properties of soils have been summarised. Present understanding on the mechanisms leading to changes in the soil properties has been elucidated. The occurrence of alkali contamination has been reviewed in this chapter which enabled to select the ranges of alkali concentration for the study. Based on the review of various methods employed to improve the soil behaviour, the use of salt solutions such as potassium chloride (KCl) and magnesium chloride (MgClB2B) and pozzolanic fly ash has been considered to counteract the alkali effects. Based on this detailed survey, the scope of the present investigation has been elaborated at the end of the chapter. Chapter 3 presents different materials used and various methods adapted in the current study. Three soils having different mineralogy have been used in this study to bring out the effect of alkali solutions on their volume change behaviour. While two soils were classified as CH, the third one was of CL. The CH soils used in this study are called Black Cotton Soils in India. One soil contained predominantly mixed layer illite-smectite mineral (BCS I) and the other contained predominantly montmorillonite mineral (BCS M). The locally available CL soil used is referred as red earth (RE) whose predominant mineral is kaolinite. Alkali solutions of concentration ranging from 1N to 4N are prepared using sodium hydroxide pellets (NaOH). Slat solutions viz. potassium chloride and magnesium chloride and pozzolanic fly ash obtained from Neyveli thermal power plant (NFA) are used as additives. Procedures to determine the geotechnical properties of the soils such as Atterberg limits, specific gravity, grain size distribution and compaction characteristics are given in this chapter. Procedures for identifying the mineral and microstructure of the soils such as X-ray diffraction (XRD) and scanning electron microscopy (SEM) are also presented in this chapter. Standard oedometer tests with fixed ring apparatus were performed to study the volume change behaviour of soils under various conditions. Volume change behaviour of soils in the presence of alkali solutions is presented in Chapter 4. In order to assess the effect of alkali solution on the volume change behaviour of soils it is necessary to study their behaviour in water. Relatively very high swell was observed in BCS M, whereas the swell in RE and BCS I soil specimens was very low and moderate respectively. Adsorption of water to form diffuse double layer near the negative surface of clay mineral particles leads to swelling in soils. The thickness of the double layer depends on the cation exchange capacity of soil. Higher cation exchange capacity leads to development of higher thickness of double layer thereby inducing swell. The higher is the swell the higher would be the compression. The effect of different concentrations (1N, 2N and 4N) of alkali solutions on volume change behaviour of three types of soil is presented in this chapter. All the three soils studied, irrespective of their mineralogical composition, exhibited high swell when contaminated with alkali solution compared to water. However, the extent and nature of swell varied both with the type of mineral present in the soil and concentration of sodium hydroxide solution. The swell in BCS I increases with increase in the concentration of the alkali solution. In 1N alkali solution the high swell occurred is due to the breaking up of interstratified mineral into constituent minerals initiated by the leaching of potassium from soil due to high pH. In 2N and 4N alkali solutions, the observed high swell occurs in two stages: the first stage of swelling is due to breaking up of interstratified mineral into constituent minerals initiated by the leaching of potassium from soil due to high pH, and the second stage of swelling is due to the formation of new minerals (Zeolite P in case of 2N NaOH and Sodalite in case of 4N NaOH). The nature of swell is influenced by the formation of minerals depending on the concentration of alkali solution. Thus the studies clearly indicate that the swelling is due to the release of potassium from soil at higher pH and due to mineralogical changes depending upon the concentration of alkali solution. Confirmative tests were conducted to support the release of potassium during first stage of swelling and mineralogical alteration after second stage of swelling. The high swell in BCS M becomes higher in 1N alkali solution. The increased swell in the soil with 1N alkali solution is due to increase in the ion exchange capacity of soil at higher pH. The swell which is very high with 1N alkali solution decreases with 2N alkali solution. With increase in concentration of alkali solution to 2N, the increase in the negative charges due to alkalinity becomes less and the swell decreases due to dominant influence of electrolyte effect. With increase in the concentration of alkali solution to 4N, both these influences become less and the amount of swell remains the same. Significant increase in the amount of swell is observed with alkali solution even in non-swelling red earth. The nature of swell as well as the formation of minerals is not altered by the change in the concentration of alkali solution. At any concentrations of alkali solution the observed swell is noticed in two stages – very small first stage of swell due to lower ion exchange capacity and considerable second stage of swell due to the formation of new mineral (Sodalite) with any concentration of alkali solution. It has been observed that the normal hyperbolic swell – compression relationship does not apply for the alkali contaminated soils. The higher swell does not result in higher compression, as the swollen soil remains fairly incompressible. Analysis of the results and detailed studies on micro-structure and mineralogy of soils bring out mechanism of alkali effects. Comparing the swell behaviour of soils with alkali solutions brings out the relative importance of various mechanisms proposed for induced heave. The effect of salt solutions used viz., potassium chloride and magnesium chloride to restrict the influence of alkali solution on the volume change behaviour of BCS I is presented in Chapter 5. These salts react with alkali solution to form partly soluble potassium hydroxide (KOH) and sparingly soluble magnesium hydroxide (Mg(OH)B2B) respectively. Presence of ionic potassium can bring out potassium linkages, by bridging potassium ion between the unit layers of expansive minerals reducing the swell. Magnesium ions can restrict swell, by replacing the monovalent exchangeable ions present in soil and/or by formation of magnesium hydroxide which is a weak cementing agent. The effect of potassium hydroxide on the volume change behaviour of soil has been studied and the results clearly indicate that fixation of potassium is facilitated by high pH of KOH solution. Addition of potassium chloride has partially controlled the alkali induced heave in soil. Of the two stages of swelling observed in soil in the presence of 4N alkali solution, only the first phase of swelling is reduced which may be due to electrolyte effect and/or due to fixation of potassium. The second phase of swelling that occurs in soil due to mineralogical changes can not be controlled with the use of potassium chloride. Addition of magnesium chloride salt solution also reduced the effect of alkali solution mostly due to suppression of thickness of diffuse double layer that develops near clay surface. The nature of reduction in the swell of alkali solution during the two stages by magnesium chloride is similar to that of potassium chloride. The partial reduction in swell of soil in the presence of salt solutions leads to reduction in the compressibility of soil. Detailed data and analysis, presented in this chapter, bring out the role of microstructure and mineralogy on soil behaviour. The abnormal volume changes due to mineralogical changes affected by high concentration of sodium hydroxide could not be controlled with salt solutions, attempts are made to utilize fly ash to control the alkali induced heave. The pozzolanic compounds produced by hydration of compounds presented and/or produced by lime silica reactions can bind the soil particles controlling the swelling. The results on the effectiveness of fly ash on BCS I soil are presented in Chapter 6. The physical and chemical properties of fly ash along with the mineralogical composition and the microstructure of the fly ash are also presented in this chapter. Before studying the effect of fly ash to control the volume change behaviour of soils in presence of alkali solutions, the effect of alkali solutions on the volume change behaviour of fly ash itself has been studied. The results showed no noticeable changes in swell and compressibility of fly ash, encouraging its use for controlling the alkali induced swell. The ability of different percentages (10%, 20% and 50%) of fly ash to control alkali induced volume changes in soil with varying concentrations of alkali solutions, viz., 1N, 2N and 4N has been studied. The results indicate that the addition of fly ash effectively reduces alkali induced swell in BCS I. The effectiveness of fly ash increases with increase in its content. The reduction in swelling of soil is partially due to replacement of soil with fly ash and mainly due to cementation of soil particles by pozzolanic compounds produced. More than 25% of fly ash is generally required to significantly reduce the swell in alkali solutions. The reduction in swell with addition of fly ash also leads to lower compressibility of soil. The role of microstructure and mineralogy in controlling the volume change behaviour are also presented in this chapter. The effectiveness of fly ash in controlling the volume changes in RE and BCS M due to alkali solutions are studied in Chapter 7. The addition of fly ash completely eliminates the swelling in both the soils. The reduction in swelling up on addition of fly ash is essentially due to efficient binding of particles by pozzolanic reaction compounds. Addition of even 10% of fly ash is sufficient in completely arresting the swelling of RE and BCS M by alkali solution. Detailed data and analysis of the results to bring out the role of microstructure and mineralogy on the behaviour of soils are presented. It is clear that relatively higher amounts of fly ash is required to control the alkali induced heave in BCS I than in other soils at higher concentrations of alkali solution. The major conclusions from the study are presented in Chapter 8. The thesis demonstrates that alkali contamination alters mineralogy and morphology of soils affecting the volume change behaviour significantly. The study also brings out that fly ash can control the undesirable swell that occurs in most types of soils by cementing the soil particles to resist swelling. Though the amount of fly ash required to control the alkali induced heave varies, 25% of fly ash is often sufficient.

Nowadays, thin-walled load bearing structures can be realised using textile reinforced concrete (BRAMESHUBER and RILEM TC 201-TRC [1]). The required tensile strength is achieved by embedding several layers of textile. By means of the laminating technique the number of textile layers that can be included into the concrete could be increased. To further increase the first crack stress and the ductility as well as to optimize the crack development, fine grained concrete mixes with short fibres can be used. By a schematic stress-strain curve the demands on short fibres are defined. Within the scope of this study, short fibres made of glass, carbon, aramid and polyvinyl alcohol are investigated in terms of their ability to fit these requirements. On the basis of these results, the development of hybrid fibre mixes to achieve the best mechanical properties is described. Additionally, a conventional FRC with one fibre type is introduced. Finally, the fresh and hardened concrete properties as well as the influence of short fibres on the load bearing behaviour of textile reinforced concrete are discussed.

Anhand von Versuchsergebnissen wird gezeigt, dass Stahlbetonbauteile mit textilbewehrtem Beton verstärkt werden können. Sowohl die Torsionstragfähigkeit als auch die Gebrauchstauglichkeit werden durch die textilbewehrte Verstärkungsschicht deutlich verbessert. Vergleichsrechnungen zeigen, dass die Torsionstragfähigkeit mit bereits bekannten Stabwerksmodellen ermittelt werden kann.

Dieser Beitrag befasst sich mit der experimentellen und analytischen Bestimmung der Verankerungslängen textiler Bewehrungsstrukturen einer Textilbetonverstärkungsschicht. Die experimentelle Untersuchung des Verbundverhaltens erfolgte anhand von Pull-Out-Versuchen. Die analytische Betrachtung des Verbundproblems geschieht aufbauend auf multilinearen Lösungen der Verbunddifferentialgleichung anhand der experimentell ermittelten Kraft- Rissöffnungs-Beziehungen. Mit Hilfe eines separaten Modells wird aus der so ermittelten Verbundspannungs-Schlupf-Beziehung (VSB) die zur Verankerung einer entsprechenden Kraft F erforderliche Verankerungslänge lE bestimmt. Die Überprüfung der Berechnung erfolgt anhand von unabhängig in experimentellen Versuchen zur Bestimmung der Verankerungslänge ermittelten Werten. Es konnte eine gute Übereinstimmung der berechneten mit den versuchstechnisch bestimmten Verankerungslängen festgestellt werden.

Die Anwendung von textilbewehrtem Beton ermöglicht vorgefertigte, filigrane und leichte Betonkonstruktionen von hoher Dauerhaftigkeit und Oberflächenqualität. Stand der Technik in der Anwendung sind hinterlüftete Fassadenplatten mit Dicken von 20-35 mm und Größen von bis zu 12,3 m², die aufgrund der geringen Querschnittssteifigkeiten nur mit metallischen oder monolithischen Aussteifungen realisierbar sind. Steife, tragfähige und dennoch leichte Querschnitte lassen sich mit Sandwichkonstruktionen erreichen, die große Spannweiten und zusätzliche Einsparpotentiale im Betoneinsatz und der Gesamtbauteilstärke ermöglichen. Insbesondere selbsttragende Sandwichkonstruktionen bieten ein hohes Anwendungspotenzial im Fassadenbereich. Der vorliegende Beitrag berichtet über Lastannahmen, Tragverhalten, Herstellung und Anwendung beim Hallenneubau des Instituts für Textiltechnik, RWTH Aachen.

On s'intéresse dans le présent travail au comportement au gel des sols fins limono-argileux traités à la chaux seule, sols valorisables qui sont couramment rencontrés sur les chantiers de terrassement. Trois sols appartenant aux classifications A1, A2, A3 selon la norme NF P 11300, ont été choisis pour cette étude. Ces sols sont traités à 3 dosages en chaux correspondant à 3 objectifs : 1) amélioration (dosage en chaux minimal), 2) stabilisation et insensibilité à l'eau (dosage en chaux intermédiaire), 3) stabilisation et résistance au gel (dosage en chaux le plus élevé). Les sols traités sont ensuite conservés pendant quatre périodes de cure : 7 jours, 28 jours, 90 jours et 365 jours. Les deux processus de gel - le géligonflement et la gélifraction sont étudiés, parallèlement à l'évaluation des performances mécaniques, hydrauliques et microstructurales. Les résultats expérimentaux ont montré que les propriétés hydrauliques (la succion au front de gel, sp et la conductivité hydraulique à l'état non-saturé, kunsat) sont les paramètres qui gouvernent le phénomène de géligonflement des sols, traités ou non. Les résultats ont également mis en évidence le lien direct existant entre la microstructure (la distribution porale) et les propriétés hydrauliques du sol, principalement en termes de capacité de rétention d'eau et conductivité hydraulique. Le traitement augmente les performances mécaniques des sols d'une part, et amène d'autre part à des modifications de leur microstructure ; ceci induit des changements vis-à-vis de leur sensibilité au gel. Les sols sont plus gélifs directement après le traitement, cette sensibilité au gel diminuant avec le temps de cure. Une modélisation simple permettant d'estimer le gonflement au gel à partir de la succion au front de gel et de la valeur de conductivité hydraulique à l'état non-saturé a été proposée et validée. Vu que la détermination de la conductivité hydraulique à l'état non-saturé n'est pas un essai couramment pratiqué au sein de la plupart des laboratoires, un critère basé sur la succion au front de gel, sp, et la conductivité hydraulique à l'état saturé, ksat a été proposé pour évaluer la sensibilité des sols au gel. L'essai de gélifraction consiste à évaluer un coefficient de résistance de l'éprouvette de sol après 10 cycles de gel/dégel, RFT (%) - « retained strength factor after freeze-thaw testing ». Les résultats expérimentaux montrent que la valeur RFT des sols traités varie de 0% (lorsque les éprouvettes de sol perdent totalement leur résistance à la compression simple et sont détruites après 10 cycles de gel/dégel) à 90%. Quand RFT ≥ 60%, aucune dégradation visuelle de la surface des éprouvettes des sols traités n'est constatée. Ainsi, cette valeur est proposée comme critère d'acceptation des matériaux constitutifs d'une couche de forme subissant le gel avant son recouvrement. L'étude de l'effet du nombre des cycles de gel/dégel montre une diminution importante de la performance mécanique (RFT) durant trois premiers cycles de gel/dégel, et ce paramètre se stabilisant après 10 cycles. A l'aide de la technique de µ Tomographie X, l'endommagement interne des éprouvettes de sol ayant subi des cycles de gel/dégel a été quantifié. Une corrélation directe entre la diminution de performance mécanique et l'augmentation de l'indice de l'endommagement de l'éprouvette a été mise en évidence. Enfin, un modèle d'endommagement permettant d'évaluer la dégradation de la performance mécanique avec l'augmentation de l'indice d'endommagement a été établi / The present work deals with the behaviour of fine-grained silty and clayey soils treated with lime under frost. Those soils are frequently encountered in earthworks. Three soils corresponding to A1, A2, A3 classes according French NF P 11-300 standard were chosen for this study. These soils were treated with 3 lime dosages corresponding to three objectives: 1) improvement (minimum dosage), 2) stabilization and insensitivity to water (intermediate dosage), 3) stabilization and frost resistance (highest dosage). Lime-treated soils were subsequently cured for different times: 7, 28, 90, 365 days. Two frost processes, frost heave and freeze-thaw cycles, were applied in parallel with the assessment of mechanical, hydraulic and microstructural properties. Experimental results evidenced that it is the hydraulic properties (suction at frost front, sp and unsaturated hydraulic conductivity, kunsat) that govern the frost heave phenomenon of soils, treated or not. In addition, this study demonstrates the direct link between the microstructure (the pore size distribution) and the hydraulic properties (water retention curve and hydraulic conductivity). The treatment on one hand improves the mechanical performances of soils, and on the other hand modify their microstructure, and thus changes their frost sensitivity. The frost susceptibility increases directly after treatment, and then decreases with curing time. Based on the suction at frost front and the unsaturated hydraulic conductivity, a simple model was proposed and validated allowing to estimate the frost heave. Considering that the determination of unsaturated hydraulic conductivity is not a test commonly performed by most laboratories, a criterion based on the suction at frost front and the saturated hydraulic conductivity was proposed to estimate the frost sensibility of soils. The second frost resistance test consists of measuring the retained strength factor after 10 freeze-thaw cycles, RFT (%). The results obtained show that RFT of lime treated soil varies from 0% (when soil specimen completely loses its resistance and collapses after 10 freezethaw cycles) to 90%. When RFT is higher than 60%, no visual damage was observed on the specimen surface; consequently, this value is proposed as a criterion for acceptance of lime treated soil in capping layer before covering. In addition, the study of effect of freeze-thaw cycles showed a significant decrease of mechanical performance (RFT) during the first three cycles, and a stabilization after 10 cycles. Using X-ray Tomography, the intern damage of specimens due to freeze-thaw cycles was quantified. A correlation between the decrease of mechanical performance and the increase of damage index was evidenced. A model was then developed to evaluate the degradation of mechanical performance with the increase of damage index

Title: Physical properties of ultrafine-grained magnesium based alloys prepared by various severe plastic deformation techniques Author: Jitka Stráská Department / Institute: Department of Physics of Materials Supervisor of the doctoral thesis: Doc. RNDr. Miloš Janeček, CSc. Abstract: The objective of the doctoral thesis is the complex investigation of ultrafine-grained magnesium alloy AZ31 prepared by two different severe plastic deformation techniques, in particular the hot extrusion followed by equal-channel angular pressing (EX-ECAP) and high pressure torsion (HPT). These severe plastic deformation methods, and as well as many others, are described in detail in the introductory theoretical section. Experimental results are summarized in the following experimental part of the thesis. Mechanical properties, lattice defect structure and especially microstructure were investigated using various experimental techniques. Thermal stability of ultrafine-grained microstructure of AZ31 after EX-ECAP was investigated and the activation energies for grain growth in different temperature ranges were calculated using kinetic equation for grain growth and Arrhenius equation. Results from the dislocation density measurements proved temperature ranges of the recovery and the following grain growth. Results from the...

No description available.

Le traitement des sols est une technique connue qui a largement été utilisée dans les constructions ferroviaires et routières. Il améliore la maniabilité des sols en réduisant la teneur en eau et en améliorant les performances hydromécaniques par renforcement et lien des agrégats du sol. Cependant, la durabilité des sols traités reste une question ouverte, elle constitue l'objectif principal du projet ANR TerDOUEST (Terrassements Durables – Ouvrages en Sols Traités, 2008-2012).La présente étude fait partie des travaux réalisés dans le cadre du projet TerDOUEST, et traite de l'effet de la taille des agrégats sur l'évolution de la raideur (Gmax) des sols fins provenant d'Héricourt (70) et traités à la chaux et/ou au ciment, à l'aide de la technique piézo-électrique (bender element). Dans les conditions de laboratoire, quatre tailles d'agrégats ont été étudiées (Dmax = 0.4, 1, 2 et 5 mm). Afin d'obtenir des tailles d'agrégats souhaitées, les sols ont d'abord été séchés, broyés puis tamisés à une taille désirée. Les sols ont ensuite été ramenés à la teneur en eau souhaitée, mélangés au liant hydraulique (chaux et/ou ciment) puis compactés du côté sec et du côté humide de l'optimum du Proctor normal, tout en conservant la même densité sèche. Les mesures de Gmax des sols traités ont été réalisées pendant la cure et pendant l'application de cycles humidification/séchage. Dans les conditions du terrain, qui correspondent au remblai expérimental d'Héricourt, les tailles des agrégats sont nettement plus élevées : Dmax = 20 et 31.5 mm pour le limon et l'argile, respectivement. Les résultats montrent que le comportement hydromécanique des sols traités est fortement influencé par la taille des agrégats, que les sols soient argileux ou limoneux, préparés en laboratoire ou bien dans les conditions du terrain : plus la taille des agrégats est élevée, plus la raideur diminue avec le temps de cure et moins les sols résistent à la succession de cycles humidification/séchage. Une forte hétérogénéité des sols in-situ a aussi été identifiée clairement. Un modèle hyperbolique a été développé afin de permettre l'application des résultats obtenus en laboratoire à ceux obtenus dans des conditions de terrain, étant donné l'effet de la taille des agrégats. La comparaison entre le modèle de prédictions et les mesures expérimentales démontre la performance du modèle proposé, à condition d'utiliser les valeurs moyennes des données expérimentales afin de minimiser l'effet de l'hétérogénéité du sol / Soil treatment is a well known earthwork technique which has been widely used in constructions of railway and highway substructures. It can improve the workability of soils by lowering their water contents and improve the hydro-mechanical performance by reinforcing and binding the soil grains/aggregates. However, the durability of the treated soils is still an open question. It constitutes the main objective of the ANR project TerDOUEST (Terrassements Durables - Ouvrages en Sols Traités, 2008 - 2012).The present study is part of the works in TerDOUEST project, and deals with the aggregate size effect on the stiffness (Gmax) development of lime and/or cement treated fine-grained soils from Héricourt using bender element technique. In the laboratory conditions, four aggregates sizes were accounted for (Dmax = 0.4, 1, 2 and 5 mm). To prepare an aggregate size, the soils were first air-dried, crushed and sieved through a target sieve. The soils were then brought to a desired water content, mixed with additive (lime and/or cement) and compacted both dry and wet of optimum of normal Proctor by keeping the same dry density. The Gmax measurements were performed during curing and during application of wetting/drying cycles. In field conditions that refer to the experimental embankment in Héricourt, the aggregates size is significantly larger: Dmax = 20 mm and 31.5 mm for the silt and the clay, respectively. Cores samples were taken from the embankment at two different times and the Gmax measurements on core specimens were performed. The results show that the hydromechanical behaviour of the cementitious treated soils is strongly influenced by the aggregates size for the treated silt and clay prepared in both laboratory and field conditions: the larger the aggregates, the lower the Gmax and the resistance to wetting/drying cycles. The high heterogeneity of the in-situ soils was also clearly identified. A hyperbolic model was developed enabling up-scaling the results in laboratory conditions to those in field conditions by considering the effect of aggregate size. Comparison between the model predictions and experimental measurements shows the performance of the model proposed, provided that the mean values of experimental data are used to minimize the effect of soil heterogeneity