The objective of this research is to experimentally investigate the flow characteristics past a bileaflet mechanical heart valve (BMHV) in an anatomical model of the aorta. The measurements were made within a mock circulation loop that produced physiological pressure and flow conditions of the aorta. The velocity was measured upstream and downstream of the valve at single points using laser Doppler velocimetry and on planes using planar particle image velocimetry. Viscous and turbulent stresses were evaluated as indicators of potential blood damage. Measurements were first made with a BMHV mounted at the inlet of an axisymmetric channel, which was similar in geometry to channels previously used, and then with the BMHV mounted at the inlet of an anatomical model of the aorta. By comparing these results, the effects of the anatomical shape of the aorta on the flow past the valve were determined. It was found that the level of turbulence past the valve was significantly greater in the axisymmetric model and that the shape of the anatomical aortic sinus, in particular, was effective in reducing turbulence. Additionally, measurements with the valve mounted in three orientations at the inlet of the anatomical aorta showed that the turbulence and the viscous stresses past the valve were lower when the valve was positioned such that its line of symmetry was parallel with the plane of aorta curvature than when it was normal to it. It was further found that flow in the right coronary artery was highest when the valve was positioned with its central orifice aligned with the opening to this artery. The results of this research may be used to assist surgeons in choosing the best implantation orientation of a BMHV.

Mitral valve disease is widely prevalent among pediatric and adult population across the world, and it encompasses a spectrum of lesions which include congenital valve defects, degenerative valve lesions, and valve dysfunction due to secondary pathologies. Though replacement of the diseased mitral valves with artificial heart valves has been the standard of care until early 1990's, current trends have veered towards complete surgical repair. These trends are encouraging, but current repair techniques are plagued with lack of durability and high rates of failure within 10 years after repair. With increasing number of patients receiving mitral valve repair, there is now an immediate need to understand the mechanisms of repair failure, and assess the role of several clinical risk factors on valve repair. In this thesis, an in vitro pulsatile left heart simulator was developed to mimic the congenital and adult mitral valve pathological morphologies in normal porcine valves, and simulate the pathological valve hemodynamics and mechanics. Different surgical repair techniques were used to correct the valve lesions, and the post repair valve hemodynamics, mechanics and geometry were assessed using quantitative measurement techniques. The extent to which each repair restores physiological valve function and mechanics was assessed, and the impact of different pathological risk factors on repair failure mechanisms was investigated. It is expected that the knowledge from this thesis would play an important role in the evolution of mitral valve surgical repair, and guide the development of more effective and long-lasting heart valve repair technologies.

Thesis (MScEng (Mechanical and Mechatronic Engineering))--Stellenbosch University, 2008. / Aortic valve replacements are frequently performed during heart surgery. However, since this is quite a stressful procedure, many patients are turned down for medical reasons. Stented valves, designed and manufactured for percutaneous insertion, eliminate many of the risks involved in open-heart surgery, thus providing a solution to patients not deemed strong enough for open-chest aortic valve replacements. The aortic valve is a complex structure, and therefore numerical simulation is necessary to obtain flow and stress data to support the design of a prosthetic heart valve in the absence of viable physical measuring methods. To aid in the design of a prosthetic heart valve, various finite element valve models were created, and the fluid structure interaction (FSI) between the valves and the blood was simulated using commercial finite element software. The effect of the geometry of the leaflets on the haemodynamic behaviour over the cardiac cycle was investigated. It was found that leaflet dimensions should be chosen judiciously, because of their considerable effect on the stress distribution and performance of the valve. A simple leaflet geometry optimisation was done for a 20 mm and 26 mm valve, respectively, by means of existing geometry relationships found in the literature. Simulations were done to obtain the maximum leaflet attachment forces that can be used by a stent designer for fatigue loading, or to investigate the structural strength of the stent. These simulations were numerically validated. The effect of leaflet thickness and stiffness on resistance to opening, stress distribution and strain were investigated. Results showed that leaflet thickness has a greater effect on the performance of the valve than leaflet stiffness, and thereby validated the results of similar tests contained in the literature. After simulating over-, as well as under-dilation of a stented valve, it was found that problems associated with over-dilation can be minimised to a certain extent by increasing the coaptation1 region of the leaflets. A simple pulse duplicator was designed based on a four-element Windkessel model. The pulse duplicator was used to study the performance of the prototype valves by means of high-speed photography, the results of which were fed into one of the numerical finite element models and compared to real valve performance. Some of the prototype valves showed efficiencies of 88%.

Native heart valves with limited functionality are commonly replaced by a bileaflet mechanical heart valve (BMHV). However, despite their widespread use, BMHVs still cause major complications, including hemolysis, platelet activation, and thromboembolic events. These complications are believed to be due to the non-physiologic hemodynamic stresses imposed on blood elements by the hinge flows. Three-dimensional characterization of the hinge flows is therefore crucial to ultimately design BMHVs with lower complication rates. This study aims at simulating the pulsatile 3D hinge flows of various BMHVs placed and estimating the thromboembolic potential associated with each hinge. The hinge and leaflet geometries of clinical BMHVs are reconstructed from micro-computed tomography scans. Simulations are conducted using a Cartesian sharp-interface immersed-boundary methodology combined with a second-order accurate fractional-step method. Physiologic flow boundary conditions and leaflet motion are extracted from the Fluid-Structure-Interaction simulations of the BMHV bulk flow. The accuracy of the solver is assessed by comparing the results with experimental data. The numerical results are analyzed using a particle tracking approach coupled with existing blood damage models to relate the flow structures to the risk for blood damage. Calculations reveal complex, unsteady, and highly 3D flow fields. Zones of flow stagnation and recirculation, favorable to thrombosis and regions of elevated shear stresses, which may induce platelet activation, are identified throughout the hinge and cardiac cycle. The hinge gap width and, more importantly, the shape of the hinge recess and leaflet are found to impact the flow distribution. Avoiding sharp corners or sudden shape transitions appear as key geometrical design parameters to minimize flow disturbances and thromboembolic potential. The computed flows underscore the need to perform full 3D pulsatile simulations throughout the cardiac cycle to fully capture the complexity and unsteadiness of the hinge flows. Though based only on three different designs, this study provides general guidelines to optimize the hinge design based on hemodynamic performance and thromboembolic potential. The developed framework enables rapid and cost-efficient pre-clinical evaluation of prototype BMHV designs prior to valve manufacturing. Application to a wide range of hinges with varying design parameters will eventually help in determining the optimal hinge design.

This dissertation centers on the study of epithelial to mesenchymal cell transition (EMT) in the heart model of valve development. EMT is a process used by specific cells to invade adjacent matrix in order to differentiate into a three-dimensional structure. The first section of the project includes a study on the effects of inorganic arsenic on EMT and therefore the environmental concerns produced by deleterious effects on EMT. The second section focuses on the discovery of an intrinsic regulator of EMT, olfactomedin-1 (OLFM1). The discovery of a novel regulator of EMT in the atrioventricular canal is interesting, by itself, as it allows us to better understand the intrinsic molecular regulation of EMT in valve formation of the heart. The activity of this protein, as a regulator of cell invasion, identifies an important checkpoint in EMT. Because OFLM1 is conserved across many species, including humans, it may be a common or shared regulator of all types of EMT including cancer. Therefore, OLFM1 represents a promising new target for an anti-cancer agent as well as a potential clinical inducer of EMT to repair congenital heart disease that include valve defects.

Background Every year about 2,500 patients in Sweden undergo surgery for heart valve disease, primarily in the aortic valve.  In contrast to the mitral valve, which can be repaired in 70% of the cases, the aortic valve is normally replaced by a mechanical or biological prosthesis. A mechanical heart valve (MHV) necessitates lifelong anticoagulation treatment with a vitamin K antagonist, most commonly warfarin, due to the high thrombogenicity of the prosthesis. The quality of the warfarin treatment is crucial in these patients. Compared to other countries, treatment quality in Sweden is very high; nonetheless, there is always room for improvement. One of the ways to achieve this improvement is to implement computerized dosing assistance. Treatment recommendations for anticoagulation intensity are based on few and old studies, making these recommendations uncertain. There is therefore a need for studies designed to establish the appropriate level of anticoagulation therapy. Aim The aim of these studies was to investigate the efficacy and safety of anticoagulation treatment among patients with mechanical heart valve prostheses in Sweden; to assess whether computerized dosing can increase the treatment quality; to investigate the influence of the treatment quality, measured by Time in Therapeutic Range (TTR) and INR variability, on the risk of complications and, finally, to establish the optimal intensity of anticoagulation treatment in this group of patients. Methods Data were obtained from AuriculA – a national quality registry established in 2006, which currently includes approximately 50% of all patients treated with oral anticoagulation in Sweden. Study II used only data from AuriculA. 769,933 warfarin-dosing suggestions proposed by the dosing algorithm in AuriculA were analysed. Accepted dose suggestions (590,939) were compared with 178,994 manually-changed doses in regard to the resultant INR value, measured as mean error (deviation from target INR) and hit rate (number of INR samples within the target range 2-3). In study III, AuriculA was used to identify patients in Sundsvall and Malmö in the period 2008 – 2011 who were receiving warfarin for a mechanical heart valve prosthesis, as well as to retrieve their INR data. Data on background characteristics and bleedings or thromboembolic complications were manually retrieved from medical records by two investigators.  A total of 534 patients with mechanical heart valve prostheses were divided into quartiles based on TTR and were compared regarding the risk of complications. For Studies I and IV, data from AuriculA were merged with the Swedish National Patient Register, SWEDEHEART/ Heart surgery, and the Swedish Cause of Death Register, comprising in total 77,423 patients on warfarin with 217,804 treatment years. Every treatment period registered in AuriculA was given an individual identification number. During the study period a patient could have any number of treatment periods. The number of complications in total and in different patient groups within the study population was investigated. Complications were defined by ICD-10 codes. Major bleeding was defined as an event necessitating hospital treatment and given a discharge diagnosis with one of the ICD-10 codes reflecting bleeding, as listed in the Appendix. Bleeding events were divided into intracranial, gastrointestinal and other bleedings. Thromboembolic complications consist of venous events (deep vein thrombosis, pulmonary embolism, venous stroke) or arterial events (stroke, TIA, acute myocardial infarction, peripheral arterial embolism). Data were analysed using both simple, descriptive statistical methods and various tests such as Mann-Whitney (or two sample Wilcoxon), T-test, Chi 2 test, ANOVA, multivariate analysis with logistic regression and survival analysis with Cox Regression with proportional hazard assumption. Results Treatment quality  Mean TTR among all patients in Study I was 76.5% whereas patients with mechanical heart valve prostheses had a TTR of 74.5%. The annual incidence of major bleeding or thromboembolic events among all patients was 2.24% and 2.65%, respectively. The incidence of intracranial bleeding was 0.37% per year in the general population and 0.51% among patients with mechanical heart valve prostheses, who also had a higher bleeding rate in total (3.37% per year). Both the mean and median errors were smaller (0.44 vs. 0.48 and 0.3 vs. 0.4, respectively) and the hit rate was higher (0.72 vs. 0.67) when the dose suggested by the algorithm was accepted, compared to when it was manually changed. TTR  In Study III there was no significant difference in the risk of thromboembolism regardless of TTR level. Risk of bleeding in quartiles I and II was more than two times higher than in the quartile with TTR >82.9. In Study IV, lower TTR (≤70%) was associated with a significantly higher rate of complications when compared with TTR >70%. Bleeding risk was higher in the group with lower TTR (HR=2.43, CI 2.02-2.89, p<0.001). After dividing patients into TTR quartiles, the rate of complications in total was significantly higher in quartiles I to III compared with quartile IV, which had the highest TTR. Risk of thromboembolism, major bleeding and death was higher in the first and second quartile compared to the quartile with the highest TTR. INR variability  Higher INR variability above mean (≥0.40) was related to a higher rate of complications compared with lower INR variability (<0.40) as shown in Study IV. Bleeding risk was higher in the group with INR variability ≥0.40 (HR = 2.15, CI 1.75-2.61, p<0.001). Comparison of quartile IV, which had the lowest INR variability, with the other three revealed that quartiles I and II, which had the highest INR variability, had significantly worse outcomes for all complications except for thromboembolic events, plus also death in quartile II. TTR and INR variability combined  High variability and low TTR combined was associated with a higher risk of bleedings (HR 2.50, CI 1.99-3.15), death (3.34, CI 2.62-4-27) and thrombosis (1.55, CI 1.21-1.99) compared to the best group. Level of anticoagulation Higher warfarin treatment intensity (mean INR 2.8-3.2 vs. 2.2-2.7) was associated with a higher rate of bleedings (HR 1.29, CI 1.06-1.58), death (1.73, CI 1.38-2.16) and complications in total (1.24, CI 1.06-1.41) after adjustment for MHV position, age and comorbidity. Conclusion Warfarin treatment quality is crucial for patients with mechanical heart valve prostheses. Computerized dosing assistance could help maintain high warfarin treatment quality. Well-managed treatment with TTR ≥70% and INR variability below mean <0.40 is associated with a lower risk of serious complications compared with a lower TTR and higher INR variability. No benefit of higher warfarin treatment intensity was found for any valve type or position.

O objetivo desse trabalho foi investigar a atividade sexual dos pacientes submetidos à cirurgia de valvopatia e compreender as repercussões emocionais desses dois eventos. Para sua realização foram convidados funcionários e pacientes dos hospitais Instituto do Coração, localizado na cidade de São Paulo e Cirurgia em Aracaju no Estado de Sergipe. A amostra da pesquisa foi composta por 35 sujeitos portadores de valvopatia de ambos os sexos, entre 20 e 45 anos, que tinham sido submetidos apenas a uma cirurgia de correção dessa enfermidade, alfabetizados e que não tinham apresentado disfunção sexual antes da cirurgia. Foi também realizado um grupo controle com 35 funcionários pertencentes aos hospitais citados e que até o momento da realização da pesquisa não eram portadores de doenças crônicas. Os participantes responderam perguntas sobre atividade sexual e também criaram quatro histórias, a partir da apresentação das imagens contidas nas Pranchas (4, 10, 13HF, 16) do Teste de Apercepção Temática (TAT). Os resultados da pesquisa apontaram, na comparação entre os grupos, para uma presença estatisticamente significante (p<0,05), no grupo de pacientes, da ansiedade como interferência negativa para o desempenho sexual e de medos como não ser aceito e não ter excitação pelo parceiro, além de não satisfazer sexualmente o parceiro. Este grupo também afirmou que houve mudanças nos seus relacionamentos familiares, sociais e amorosos após a cirurgia. O TAT apontou para uma maior intensidade das necessidades emocionais de planejar e manter uma atividade sexual, apoio e afiliação no grupo de pacientes. Sugere-se que, em estudos posteriores, inclua-se o parceiro na amostra a ser pesquisada, uma vez que suas respostas podem complementar os achados do estudo e também se inclua as entrevistas em outros momentos como o pré-cirúrgico, o que contribuirá para uma melhor interpretação na análise da situação-problema. / The objective of this study was to investigate the sexual activity of patients submitted to the surgery of valvopathy and understand the emotional repercussions of these two events. For its realization were invited hospital staff and patients from the hospitals Instituto do Coração do Hospital das Clínicas da Universidade de São Paulo, and Hospital Cirurgia in Aracaju, both located in Brazil. The research sample consisted of 35 citizens of both gender who are affected by a valvopathy, between 20 and 45 years, that had been submitted only to a one surgery of correction of this disease, literate and that they have not presented some sexual dysfunction before the surgery. It also held a control group with 35 employees belonging to the hospitals cited and that until the completion of the research were not carriers of chronic diseases. The participants had answered questions about sexual activity and also created four stories from the presentation of the images contained in plates 4, 10, 13HF and 16 of the Thematic Apperception Test (TAT). The research results had pointed, in the comparison between groups, a statistically significant (p < 0.05) presence, in the group of patients, of the anxiety as a negative interference for the sexual performance, and the presence of sexual fears such as not be accepted by the partner, not be excited about the partner, and not sexually satisfy your partner. This group also affirmed that it had changes in its familiar, social and love relationships after the surgery. The TAT pointed a greater intensity of emotional needs to plan and maintain a sexual activity, support and membership in the group of patients. It is suggested that in further studies the partner should be included in the sample to be investigated, since their responses can complement the findings of the study and also includes interviews at other times as the pre-surgical, which must contribute to a better interpretation and analysis of the situation-problem

O expressivo número de brasileiros que necessitam correção anatômica da estenose valvar aórtica acentuada e que não realizam cirurgia de substituição valvar devido ao risco proibitivo justifica a necessidade de investigação, tanto da efetividade no cenário clínico real quanto dos custos impostos ao Sistema Único de Saúde e aos planos de saúde suplementar brasileiros pela incorporação do implante transcateter de valva aórtica, que tem se demonstrado efetivo mas oneroso, internacionalmente. No primeiro artigo da tese, avaliaram-se os desfechos intra-hospitalares, a sobrevida e o reembolso pela internação hospitalar de 41 pacientes com idade média de 78,7 ± 6,3 anos, estenose valvar aórtica acentuada, com recusa cirúrgica e decisão multidisciplinar por tratamento transcateter entre outubro de 2010 e outubro de 2015. Os sujeitos foram seguidos prospectivamente por um período mediano de 15,2 (4,5 – 25,6) meses e a sobrevida estimada em 1 e 2 anos foi de 73,2% e 64,1%, respectivamente. Identificou-se que hipertensão pulmonar e revascularização miocárdica cirúrgica prévia estavam independentemente associadas à menor sobrevida. O valor mediano reembolsado pelos pacientes atendidos pelo Sistema Único de Saúde foi R$ 108.634,34 (101.051,05 – 127.255,27) e R$ 115.126,77 (94.603,21 – 132.603,01) para aqueles internados por planos de saúde suplementar ou particulares, sendo o respectivo valor mediano reembolsado pela prótese valvar de R$ 82.000,00 (82.000,00 – 95.450,00) e 84.050,00 (75.000,00 – 92.400,00) Em um grupo de 585 procedimentos de troca valvar aórtica cirúrgica em indivíduos com idade ≥ 60 anos, realizados entre janeiro de 2010 e dezembro de 2015 na mesma instituição, a mortalidade intra-hospitalar estava associada à idade e foi de 5,9% naqueles com idade entre 60 e 70 anos, 10,8% entre 70 e 80 anos e de 22,2% ≥ 80 anos. O reembolso mediano foi de R$ 14.035,96 (11.956,11 – 16.644,90) para os internados pelo Sistema único de Saúde e R$ 20.273,97 (15.358.03 – 32.815,49) pelos planos de saúde suplementar ou particulares. No segundo artigo da tese, identificou-se que do total de 819 pacientes consecutivamente incluídos no Registro Brasileiro de Implante de Bioprótese Aórtica por Cateter entre janeiro de 2008 e outubro de 2015, 15 (1,8%) sofreram perfuração do ventrículo esquerdo. Os pacientes que apresentaram perfuração eram mais idosos (85,4 ± 6,3 vs. 81,5 ± 7,3 anos, p=0,038), predominantemente mulheres (80,0% vs. 50,5%, p=0,024), apresentavam maior fração de ejeção (67,3 ± 7,8% vs. 58,6 ± 15,0%, p=0,001), menor massa ventricular esquerda (203,9 ± 47,1g vs. 247,6 ± 78,7g, p=0,039) e menor altura do tronco da coronária esquerda (11,2 ± 5,4mm vs. 14,0 ± 3,3mm, p=0,034). Os preditores independentes de perfuração do ventrículo esquerdo foram idade e fração de ejeção. No terceiro artigo, descreve-se um caso de ablação septal para tratamento de miocardiopatia hipertrófica obstrutiva assimétrica para posterior implante transcateter de valva aórtica, sugerindo que esta seja uma estratégia factível quando da concomitância dessas duas condições Em conclusão, os desfechos do tratamento transcateter da estenose valvar aórtica acentuada em pacientes inoperáveis são compatíveis com aqueles do cenário idealizado dos ensaios clínicos randomizados, apesar de estarem associados a custos maiores que os anteriormente estimados por painéis de especialistas. O tratamento cirúrgico, por sua vez, apresentou mortalidade maior que aquela idealizada ou relatada como usual. A hipercinesia do ventrículo esquerdo pode favorecer o trauma determinado pelo guia metálico, posicionado em seu interior para realização do procedimento, estando a fração de ejeção independentemente associada à chance de perfuração. Ainda, a ablação septal por álcool eletiva, anterior ao implante transcateter da valva aórtica, é uma abordagem factível para pacientes com hipertrofia ventricular esquerda assimétrica obstrutiva associada à estenose valvar aórtica. / The expressive number of Brazilians who require an anatomic correction for severe aortic valve stenosis and who do not undergo valvar replacement surgery due to prohibitive risk justifies the need to investigate both the effectiveness in the real clinical scenario and the costs imposed to the Public Health System and the Supplementary Health System for the incorporation of the transcatheter aortic valve implantation, which has been shown to be effective but onerous, internationally. In the first article of the thesis, the in-hospital outcomes, long-term survival and reimbursement for 41 patients, with a mean age of 78.7 ± 6.3 years, sever aortic valve stenosis, with surgical refusal and multidisciplinary decision for transcatheter treatment, between October 2010 and October 2015 are described. Subjects were prospectively followed for a median period of 15.2 (4.5 - 25.6) months and the estimated survival at 1 and 2 years was 73.2% and 64.1%, respectively. It was identified that pulmonary hypertension and previous coronary artery bypass grafting were independently associated with lower survival. Median reimbursed values by the Public Health System was R$ 108,634.34 (101,051.05 - 127,255.27) and by supplementary health plans was R$ 115,126.77 (94,603.21 - 132,603.01). The respective median values reimbursed for the valve prosthesis was R$ 82,000.00 (82,000.00 - 95,450.00) and 84,050.00 (75,000.00 - 92,400.00) In a group of 585 surgical aortic valve replacement procedures in subjects aged ≥ 60 years, performed between January 2010 and December 2015 in the same institution, in-hospital mortality was associated with age and was 5.9% in those with age between 60 and 70 years, 10.8% between 70 and 80 years and 22.2% in ≥ 80 years. The median reimbursement was R$ 14,035.96 (11,956.11 - 16,644.90) for those hospitalized by the Public Health System and R$ 20,273.97 (15,358.03 - 32,815.49) by supplementary or private health plans. In the second article of the thesis, it was identified that of the total of 819 patients consecutively included in the Brazilian Registry of Aortic Bioprosthesis Implantation by Catheter (RIBAC) between January 2008 and October 2015, 15 (1.8%) suffered perforation of the left ventricle. Patients with perforation were older (85.4 ± 6.3 vs. 81.5 ± 7.3 years, p=0.038), predominantly women (80.0% vs. 50.5%, p=0.024), had a higher ejection fraction (67.3 ± 7.8% vs. 58.6 ± 15.0%, p=0.001), lower left ventricular mass (203.9 ± 47.1g vs. 247.6 ± 78, 7g, p=0.039) and shorter distance between the aortic annulus and the left main coronary artery ostium (11.2 ± 5.4mm vs. 14.0 ± 3.3mm, p=0.034). The independent predictors of left ventricular perforation were age and ejection fraction. In the third article, a case of septal ablation was described for the treatment of asymmetric obstructive hypertrophic cardiomyopathy for posterior transcatheter aortic valve implantation, suggesting that this is a feasible strategy when these two conditions are concomitant In conclusion, the outcomes of transcatheter treatment of severe aortic stenosis in inoperable patients are compatible with those in the ideal scenario of randomized clinical trials, although they are associated with higher costs than previously estimated by expert panels. Surgical treatment, on the other hand, presented higher mortality than that idealized or reported as usual. The left ventricle hyperkinesia may favor the trauma determined by the metallic guide, positioned inside it to perform the procedure, the ejection fraction being independently associated with the chance of perforation. Furthermore, elective alcohol septal ablation, prior to transcatheter aortic valve implantation, is a feasible approach for patients with obstructive asymmetric left ventricular hypertrophy associated with aortic valve stenosis.

O objetivo deste trabalho foi estudar e comparar a valva mitral e a valva aórtica e em corações com cardiomiopatia dilatada (CMD) de etiologia isquêmica e idiopática, em relação aos corações humanos normais, buscando identificar variações que possam auxiliar em diagnósticos por imagem e para o tratamento cirúrgico das mesmas. Este estudo analisou 22 corações normais, 15 corações dilatados de etiologia isquêmica e 15 corações dilatados de etiologia idiopática, fixados em formaldeído a 10%. Foram obtidas medidas por meio de fotografias digitais dos corações e, posteriormente, utilizando-se software, foram analisados as distâncias e os perímetros da valva mitral e da valva aórtica, que foram comparadas por meio de testes estatísticos. Nos corações normais, a área da valva mitral foi de 5,44 ± 0,82 cm2 e o perímetro de 8,91 ± 0,57 cm, e nos corações com CMD de etiologia isquêmica e idiopática, a área foi de, respectivamente, 7,38 ± 1,76 cm2 e 7,03 ± 1,44 cm2, e o perímetro foi de, respectivamente, 10,41 ± 1,37 cm e 9,97 ± 1,23 cm. O perímetro de inserção da cúspide anterior da valva mitral, nos corações normais, foi de 3,68 ± 0,52 cm e nos corações com CMD de etiologia isquêmica e idiopática foi de, respectivamente, 3,99 ± 0,86 cm e 3,62 ± 0,78 cm. A menor distância perimetral entre os trígonos fibrosos (porção fibrosa), nos corações normais, foi de 2,06 ± 0,26 cm e nos corações com CMD de etiologia isquêmica e idiopática foi de, respectivamente, 2,64 ± 0,37 cm e 2,34 ± 0,37 cm. Nos corações normais, a área da valva aórtica foi de 3,46 ± 0,66 cm2 e o perímetro de 6,83 ± 0,66 cm. Nos corações com CMD de etiologia isquêmica e idiopática, a área da valva aórtica foi de, respectivamente, 5,22 ± 1,53 cm2 e 3,44 ± 1,33 cm2, e o perímetro de, respectivamente, 8,26 ± 1,24 cm e 6,82 ± 1,37 cm. Nos casos de CMD idiopática e isquêmica, a valva mitral apresentava-se aumentada, tanto na sua área e em seu perímetro, quanto na maior e na menor distância perimetral entre os trígonos fibrosos. Em relação à valva aórtica, apenas nos corações com CMD isquêmica houve aumento estatisticamente significante em sua área e em seu perímetro, enquanto que nos corações com CMD idiopática não houve diferença quando comparados aos corações normais. Há manutenção da proporcionalidade, dos corações normais para os com CMD idiopática e isquêmica, das distâncias entre os trígonos fibrosos. Há evidência de que o aumento da valva mitral e da valva aórtica, quando ocorrem na CMD, se dão de forma independente. / The objective of this work was to study and to compare mitral valve as well as aortic valve in the ischemic and idiopathic dilated cardiomyopathy (CMD) in relation to the normal hearts, searching to identify variations that can assist in diagnostic for image and for the surgical treatment of the same ones. This study it analyzed 22 normal hearts, 15 dilated hearts of ischemic etiology and 15 dilated hearts of idiopathic etiology, fixed in formaldehyde 10%. They had been gotten measured through digitalized photographs of the hearts, and, through software, the distances and perimeters of the mitral valve and of the aortic valve had been analyzed, that later they had been compared through statistical tests. In the normal hearts, the area the mitral valve was 5.44 ± 0.82 cm2 and the perimeter of 8.91 ± 0.57 cm. In the hearts with ischemic and idiopathic CMD the area of the mitral valve were, respectively, 7.38 ± 1.76 cm2 and 7.03 ± 1.44 cm2, and to the perimeter it were, respectively, 10.41 ± 1.37 cm and 9.97 ± 1.23 cm. The perimeter of insertion of anterior cusp of mitral valve in the normal hearts was 3.68 ± 0.52 cm, in the hearts with ischemic and idiopathic CMD were, respectively, 3.99 ± 0.86 cm and 3.62 ± 0.78 cm. The lesser length enter the fibrous trigones (fibrous portion) in the normal hearts was 2.06 ± 0.26 cm and in the hearts with ischemic and idiopathic CMD were, respectively, 2.64 ± 0.37 cm and 2.34 ± 0.37 cm In the normal hearts the area of aortic valve was 3.46 ± 0.66 cm2 and the perimeter of 6.83 ± 0.66 cm. In the hearts with ischemic and idiopathic CMD the area of aortic valve were, respectively, 5.22 ± 1.53 cm2 and 3.44 ± 1.33 cm2, and the perimeter of, respectively, 8.26 ± 1.24 cm and 6.82 ± 1.37 cm. In the cases of idiopathic and ischemic CMD, mitral valve is presented increased, as much in its area and its perimeter, how much in the greater and the lesser perimetral distance between the fibrous trigones. In relation to aortic valve, only in the hearts with Ischemic CMD it had significant statistic increase in its area and its perimeter, whereas in the hearts with Idiopathic CMD it did not have difference when compared with the normal hearts. It has maintenance of the proportionality, the normal hearts for the ones with idiopathic and ischemic CMD, of the distances between the fibrous trigones. It has evidence of that the increase of mitral valve and aortic valve, when they occur in the CMD, occurs of independent form.

A major drawback in the operation of mechanical heart valve prostheses is thrombus formation in the near valve region potentially due to the high shear stresses present in the leakage jet flows through small gaps between leaflets and the valve housing. Detailed flow analysis in this region during the valve closure phase is of interest in understanding the relationship between shear stress and platelet activation. An efficient Cartesian grid method is developed for the simulation of incompressible flows around stationary and moving three-dimensional immersed solid bodies as well as fluid-fluid interfaces. The embedded boundaries are represented using Levelsets and treated in a sharp manner without the use of source terms to represent boundary effects. The resulting algorithm is implemented in a straightforward manner in three dimensions and retains global second-order accuracy. When dealing with problems of disparate length scales encountered in many applications, it is necessary to resolve the physically important length scales adequately to ensure accuracy of the solution. Fixed grid methods often have the disadvantage of heavy mesh requirement for well resolved calculations. A quadtree based adaptive local mesh refinement scheme is developed to complement the sharp interface Cartesian grid method scheme for efficient and optimized calculations. Detailed timing and accuracy data is presented for a variety of benchmark problems involving moving boundaries. The above method is then applied to modeling heart valve closure and predicting thrombus formation. Leaflet motion is calculated dynamically based on the fluid forces acting on it employing a fluid-structure interaction algorithm. Platelets are modeled and tracked as point particles by a Lagrangian particle tracking method which incorporates the hemodynamic forces on the particles. Leaflet closure dynamics including rebound is analyzed and validated against previous studies. Vortex shedding and formation of recirculation regions are observed downstream of the valve, particularly in the gap between the valve and the housing. Particle exposure to high shear and entrapment in recirculation regions with high residence time in the vicinity of the valve are observed corresponding to regions prone to thrombus formation.