Additive manufacturing (AM) has the ability to fabricate components of high geometric complexity that are difficult or near impossible to be produced by traditional manufacturing technologies. Selective laser melting (SLM) is a commonly used AM technology for metallic fabrications. SLM offers the opportunities to customize the characteristics of the as-build part produced, by adjusting the laser settings. However, high strength aluminum (Al) alloys presents an obstacle for SLM production due to the low alloying content, which increases the alloys’ probabilities to form cracks due to thermal stress induced by the SLM build process. The current study focuses on the study of surface roughness and dimensional accuracy of SLM fabrication of Al6061 and AlSi10Mg. Using design of experiment (DOE), wide ranges SLM process parameters were experimented with, and their individual effect along with their interactive effects on the fabricated parts’ quality were evaluated. The quality characteristics studied are: microstructures, microhardness, tensile strength (ultimate tensile strength, and yield strength), density, surface roughness, and dimensional accuracy. Regression models were created for each quality characteristics, and the combination of density, surface roughness, and dimensional accuracy results was used to create processing window for SLM that ensures the production of high-quality parts. The work aims to not only be used as-is, to help with the selection of SLM process parameters for Al6061 and AlSi10Mg that will reduce the post- processing time, but also to set a foundation for future development for numerical models that could better predict and describe the relations between SLM process parameters and the part’s fundamental qualities. / Thesis / Master of Applied Science (MASc)

The main aim of this thesis is to investigate the manufacturability of different gyroid designs using Selective laser melting (SLM) process . This study paves the way for a better understanding of design aspects, process optimization, and characterization of titanium alloy (Ti6Al4V) gyroid lattice structures for bone implant applications. First, A MATLAB® code was developed to create various gyroid designs and understand the relationship between the implicit equation parameters and the measurable outputs of gyroid unit cells. A novel gyroid lattice structure is proposed, where the porosity is graded in a radial direction. Second, gyroid designs were investigated by developing a permissible design map to help choose the right gyroid parameters for bone implants. Third, response surface methodology was used to study the process-structure-property relationship and understand the effect of SLM process parameters on the manufacturability of Ti6Al4V gyroid lattice structures. Laser power was found to be the most significant factor affecting the errors in relative density and strut size of gyroid structures. A volumetric energy density between 85 and 103 J/mm3 induces the least errors in the gyroid’s relative density. Fourth, the quasi-static properties of the novel designs were compared to uniform gyroids. The proposed novel gyroids had the highest compressive strength reaching 160 MPa. Numerical simulations were studied to give insight into how manufacturing irregularities can affect the mechanical properties of gyroids. Last, an in-depth defect analysis was conducted to understand how SLM defects may influence the fatigue properties of different Ti6Al4V gyroids. Thin struts have less internal defects than thick ones; thus, they show less crack propagation rate and higher normalized fatigue life. These favorable findings contributed to scientific knowledge of manufacturability of Ti6Al4V porosity graded gyroids and determined the influence of SLM defects on the mechanical properties of gyroid designs for bone implants. / Thesis / Doctor of Philosophy (PhD) / This thesis studies the integration of design aspects, SLM manufacturability, and mechanical characterization of Ti6Al4V gyroid lattice structures used for bone implants. A MATLAB® code was developed to design novel porosity graded gyroids, and develop permissible design map to aid the choice of different gyroid designs for bone implants.. Process maps were also developed to investigate the relationship among laser power, scan speed, and the errors in the relative density of lattice structures. Moreover, the normalized fatigue strength of thin struts gyoid was found to be higher than that of thicker struts.Analytical models and finite element analysis (FEA) models were compared to experimental results. The variation of the results gives a better understanding of the effect of manufacturing defects. An improved insight of gyroids manufacturability has been obtained by integrating the permissible design space with the process-structure-property relationship, and the defect analysis of porosity graded gyroids.

The goal of this research is developing a computational framework to study mechanical fatigue and fracture at different length scales for a broad range of materials. The developed multiscale framework is utilized to study the details of fracture and fatigue for the rolling contact in rails, additively manufactured alloys, and bio-inspired hierarchical materials. Rolling contact fatigue (RCF) is a major source of failure and a dominant cause of maintenance and replacements in many railways around the world. The highly-localized stress in a relatively small contact area at the wheel-rail interface promotes micro-crack initiation and propagation near the surface of the rail. 2D and 3D microstructural-based computational frameworks are developed for studying the rolling contact fatigue in rail materials. The method can predict RCF life and simulate crack initiation sites under various conditions. The results obtained from studying RCF behavior in different conditions will help better maintenance of the railways and increase the safety of trains. The developed framework is employed to study the fracture and fatigue behavior in 3D printed metallic alloys fabricated by selective laser melting (SLM) method. SLM method as a part of metal additive manufacturing (AM) technologies is revolutionizing the manufacturing sector and is being utilized across a diverse array of industries, including biomedical, automotive, aerospace, energy, consumer goods, and many others. Since experiments on 3D printed alloys are considerably time-consuming and expensive, computational analysis is a proper alternative to reduce cost and time. In this research, a computational framework is developed to study fracture and fatigue in different scales in 3D printed alloys fabricated by the SLM method. Our method for studying the fatigue at the microstructural level of 3D printed alloys is pioneering with no similar work being available in the literature. Our studies can be used as a first step toward establishing comprehensive numerical frameworks to investigate fracture and fatigue behavior of 3D metallic devices with complex geometries, fabricated by 3D printing. Composite materials are fabricated by combining the attractive mechanical properties of materials into one system. A combination of materials with different mechanical properties, size, geometry, and order of different phases can lead to fabricating a new material with a wide range of properties. A fundamental problem in engineering is how to find the design that exhibits the best combination of these properties. Biological composites like bone, nacre, and teeth attracted much attention among the researchers. These materials are constructed from simple building blocks and show an uncommon combination of high strength and toughness. By inspiring from simple building blocks in bio-inspired materials, we have simulated fracture behavior of a pre-designed composite material consisting of soft and stiff building blocks. The results show a better performance of bio-inspired composites compared to their building blocks. Furthermore, an optimization methodology is implemented into the designing the bio-inspired composites for the first time, which enables us to perform the bio-inspired material design with the target of finding the most efficient geometries that can resist defects in their structure. This study can be used as an effective reference for creating damage-tolerant structures with improved mechanical behavior. / Doctor of Philosophy / The goal of this research is developing a multiscale framework to study the details of fracture and fatigue for the rolling contact in rails, additively manufactured alloys, and bio-inspired hierarchical materials. Rolling contact fatigue (RCF) is a major source of failure and a dominant cause of maintenance and replacements in many railways around the world. Different computational models are developed for studying rolling contact fatigue in rail materials. The method can predict RCF life and simulate crack initiation sites under various conditions and the results will help better maintenance of the railways and increase the safety of trains. The developed model is employed to study the fracture and fatigue behavior in 3D printed metals created by the selective laser melting (SLM) method. SLM method as a part of metal additive manufacturing (AM) technologies is revolutionizing industries including biomedical, automotive, aerospace, energy, and many others. Since experiments on 3D printed metals are considerably time-consuming and expensive, computational analysis is a proper alternative to reduce cost and time. Our method for studying the fatigue at the microstructural level of 3D printed alloys can help to create more fatigue and fracture resistant materials. In the last section, we have studied fracture behavior in bio-inspired materials. A fundamental problem in engineering is how to find the design that exhibits the best combination of mechanical properties. Biological materials like bone, nacre, and teeth are constructed from simple building blocks and show a surprising combination of high strength and toughness. By inspiring from these materials, we have simulated fracture behavior of a pre-designed composite material consisting of soft and stiff building blocks. The results show a better performance of bio-inspired structure compared to its building blocks. Furthermore, an optimization method is implemented into the designing the bio-inspired structures for the first time, which enables us to perform the bio-inspired material design with the target of finding the most efficient geometries that can resist defects in their structure.

This thesis explores the optimization of process parameters for producing single-track thin walls using Laser Powder Bed Fusion (LPBF) additive manufacturing. Using two different coupon designs, the study assesses the feasibility of creating the thinnest possible leak-tight structures within LPBF and evaluating their mechanical properties, including burst pressure and modulus of elasticity under pressure loads. A series of experimental iterations were conducted, varying laser power and laser speed to identify optimal conditions. The findings indicate that a narrow range of process parameters can produce consistently leak-tight thin walls. The results contribute to understanding how to achieve high quality, reliable thin wall structures in the LPBF process, with implications for industrial applications requiring thin, precise, leak tight, and durable walls.

The main problem encountered in this thesis is the lack of research and knowledge of selective laser melted-printing with Uddeholm Dievar®. This absence of information could cause issues regarding quality and properties of the alloy as well as uncertainty regarding an appropriate heat treatment cycle. This thesis mainly focuses on observing the changes that occur in the microstructure when Uddeholm Dievar® is manufactured through the additive manufacturing (AM) method known as selective laser melting (SLM). The SLM- method consists of a high-power laser that melts together thin layers of powder, one layer at a time, until a three-dimensional product is created according to selected drawings. The methodology on which this thesis is based on is the execution of a theoretical study, scientific experiments and thermodynamic calculations. Analysis of the microstructure is performed using a scanning electron microscope with techniques such as Energy-dispersive X-ray spectroscopy (EDS) and Electron backscatter diffraction (EBSD). The purpose of the methods are to map the constituent elements of the alloy and observe the orientation of the crystallographic phases in the atomic lattice respectively. The results show that the powder, both before and after printing, mainly consists of martensite with a low amount of residual austenite. The amount of primary carbides is relatively low and has been classified as MC (V-rich) and/or M6C (Mo- rich) type. The remaining residual austenite could be explained by the segregation of constituent alloying elements, where the carbon content is a dominant factor to why the MS -temperature lowers significantly causing the presence of retained austenite even though SLM has a cooling rate that varies between 103 and 108 [K/s]. / Det huvudsakliga problemet som denna avhandling behandlar är bristen på forskning och kunskap inom selective laser melting (SLM) 3D-printing med Uddeholm Dievar®. Avsaknaden kan leda till sämre kvalité och produktegenskaper hos legeringen. Det kan även leda till ovisshet gällande val av lämplig värmebehandling. Arbetet fokuserar på att dokumentera utformningen av stålets mikrostruktur när Uddeholm Dievar® tillverkas med den additiva tillverkningsmetoden SLM. Tillverkningsprocessen består av en högeffektslaser som detaljerat smälter samman tunna lager pulver, ett lager i taget, tills att en tredimensionell produkt skapats utefter valda ritningar. Använda metoder är; utförandet av en teoretisk studie, vetenskapliga experiment och thermodynamiska beräkningar. Analys av mikrostrukturen genomförs med hjälp av svepelektronmikroskåp där teknikerna Energy-dispersive X-ray spectroscopy (EDS) och Electron backscatter diffraction (EBSD) används. Syftet med EDS är att kartlägga de ingående elementen i legeringen, syftet med EBSD är att se orientering av de kristallografiska faserna i atomgittret. Resultaten visar på att legeringen, både före och efter printing, till största del består av martensit med en låg mängd restaustenit. Mängden primärkarbider är relativt låg och har klassifiserats som typen MC (V-rik) och/eller M6C (Mo- rik). Den kvarstående restausteniten kan möjligen förklaras av segringen av ingående legeringsämnen där kolhalten är en dominerande faktor som sänker MS-temperaturen. Detta gör att restaustenit förekommer trots den höga kylhastigheten som varierar mellan 103 och 108 [K/s] i SLM.

Additive Fertigungsverfahren stellen in den letzten Jahren einen Megatrend dar, da sich mit diesen Verfahren endkonturnahe Werkstücke mit hohem Materialausnutzungsgrad herstellen lassen. Die auch als 3D-Druck bekannt gewordenen additiven Fertigungsverfahren sind jedoch nicht auf die Prototypenfertigung aus Kunststoffen begrenzt. Beim selektiven Laserschmelzen werden metallische Werkstoffe im Pulverbettverfahren mittels Laserstrahl aufgeschmolzen und somit schichtweise aufgebaut. Das Verfahren findet bereits in der Luft- und Raumfahrt, der Medizintechnik, aber auch in der Automobilindustrie und im Maschinenbau Anwendung für Prototypen, Einzelanfertigungen oder Kleinstserien. Des Weiteren ermöglicht es auch die Herstellung von Werkstücken mit besonders hoher Komplexität, die mit spanenden Verfahren nicht herstellbar sind, und bietet dadurch neue Gestaltungsmöglichkeiten bei der Konstruktion. Innerhalb des Vortrags werden nach der Vorstellung des Verfahrens verschiedene Methoden zur numerischen Simulation des selektiven Laserschmelzens von Edelstahl (1.4404) am Beispiel der kommerziellen Software Simufact Additive erläutert. Dazu werden der mechanische und thermo-mechanische Lösungsansatz betrachtet sowie die Methode zur Kalibrierung der Simulationen erläutert. Die Erläuterung eines voll transienten thermo-mechanischen Ansatzes erfolgt unter Verwendung der Software MSC Marc. Des Weiteren wird der Einfluss der Orientierung des Werkstücks im Herstellungsprozess auf resultierende Spannungen, Verzug sowie mechanische Eigenschaften analysiert und mit experimentellen Untersuchungen untersetzt.

Additive manufacturing (AM) is an attractive way to shorten development time, reduce product weight and allow the manufacturing of more complex products than by conventional manufacturing processes. The problem arises when the previous traditional manufacturing requirements need to be fulfilled by AM as well as the volume production capability. This investigation is done together with Ericsson to evaluate the possibilities of the different AM technologies, post-processing methods and silver coating processes to guarantee the specifications of radiofrequency (RF) filters. Here, minimal RF signal insertion losses are targeted. Since insertion losses are dependent on surface roughness, surface smoothness is sought as well. Ericsson simulation software uses correction factors to account for surface roughness, however there are some inconsistencies between the simulated and actual surface roughness that is allowed in the parts. In AM parts, surface roughness is not easy to control since it depends on parameters related to feedstock, process and machine properties. Commonly, most AM components do not comply with requirements of lower surface roughness values. Therefore, parts need to be smoothened before silver plated; this step is necessary to ensure the electrical conductivity in this specific application. These finishing processes add costs to the final product and increase time to market. Firstly, a comprehensive study was carried out to better understand the landscape of AM technologies, postprocessing and silver coating methods. Secondly, the different processes are assessed with the help of selection matrices, considering the products requirements. The components to print are two RF filters with different shapes and dimensions but similar requirements. The CAD design is modified depending on each AM process and directly affects the results. Afterwards, the design of an experimental plan is carried out; the number of samples of each part comparing AM technologies, feedstock, different suppliers (3D printing and post-processing) is obtained. Due to budget and time restrictions, the parts were printed using Multi Jet Fusion and Selective Laser Melting processes. After printing, tolerances and surface roughness were measured. This thesis results in the selection of suitable AM technologies and post-processing methods for RF filters. For MJF printed cavities at 0˚, 30˚ and 90˚ orientation, the best results for this application are obtained at 30˚ providing a good balance between sharp detail and smooth surfaces. In the case of SLM, waveguides are printed at 0˚ and 30˚. 30˚ waveguides present lower surface roughness values than the 0˚ ones as inner support material is needed at 0˚ orientation. SLM cavities were printed at 30˚ in seek of asymmetry between faces, resulting in higher surface roughness in the downfacing face.

Total Hip Arthroplasty (THA) is an orthopaedic procedure that is performed to reduce pain and restore the functionality of hip joints that are affected by degenerative diseases. The outcomes of THA are generally good. However, the stress shielding of the periprosthetic femur is a factor that can contribute towards the premature loosening of the femoral stem. In order to improve the stress shielding characteristics of metallic femoral stems, stiffness configurations that offer more flexibility should be considered. This research has investigated the potential of more flexible and lightweight cobalt chromium molybdenum (CoCrMo) femoral stems that can be manufactured using Selective Laser Melting (SLM). Square pore cellular structures with compressive properties that are similar to human bone have been presented and incorporated into femoral stems by utilising fully porous and functionally graded designs. A three dimensional finite element model has been developed to investigate and compare the load transfer to the periprosthetic femur when implanted with femoral stems offering different stiffness configurations. It was shown that the load transfer was improved when the properties of the square pore cellular structures were incorporated into the femoral stem designs. Factors affecting the manufacturability and production of laser melted femoral stems have been investigated. A femoral stem design has been proposed for cemented or cementless fixation. Physical testing has shown that a functionally graded stem can be repeatedly manufactured using SLM, which was 48% lighter and 60% more flexible than a traditional CoCrMo prosthesis. The research presented in this thesis has provided an early indication of utilising SLM to manufacture lightweight CoCrMo femoral stems with levels of flexibility that have the potential to reduce stress shielding in the periprosthetic femur.

La fusion sélective par laser est un procédé de la technologie de fabrication rapide de plus en plus utilisé dans l’industrie automobile, aéronautique, médicale, etc. Selon le principe de la fabrication rapide, la pièce est fabriquée couche par couche en fusionnant et soudant les particules fines par laser. Actuellement, les principaux matériaux utilisés sont les métaux métalliques ou les polymères. Le faible ou modeste point de fusion de ces matériaux conduit à une mise en œuvre par laser relativement facile. Cependant, en raison de leur point de fusion élevé, de la forte résistance à haute température et de la faible conductivité thermique, l’utilisation de matériaux céramiques est limitée dans la technologie de fusion laser sélective. Cette étude explore la fusion laser sélective de zircone stabilisée par yttrine avec un laser à fibre de longueur d’onde d’environ 1 µm. L’influence de différentes puissances de laser et de différentes vitesses de balayage sur la microstructure et la déformation de l’échantillon a été étudiée, et la densité relative et la microdureté ont été mesurées. Notamment, l’effet de différentes températures de préchauffage sur la microstructure sera étudié. En même temps, la structure cristalline céramique et la transformation des phases pendant le procédé de prototypage rapide ont été analysées. Les résultats expérimentaux montrent qu’il est possible de fondre complètement de la poudre YSZ avec un laser à fibre NIR, et avec l’optimisation des paramètres de fabrication, la densité relative de l’échantillon peut atteindre 91 %. Il est inévitable de voir se former des fissures et des pores dans les pièces fabriquées du fait de l’hétérogénéité de la distribution de l’énergie du laser. Cette distribution de l’énergie peut être améliorée grâce à l’optimisation des paramètres ; les longueurs de fissure peuvent être contrôlées et maîtrisées par un préchauffage du lit de poudre. Notamment, à haute température (1500°C, 2000°C et 2500°C) de préchauffage, la fissure verticale continue devient désordonnée et courte. Une transformation de la structure monoclinique et cubique en structure tétragonale s’est produite pendant le processus de fabrication. / Selective laser melting is a rapid manufacturing process coming from the rapid prototyping technology, which is widely used in the automotive, aeronautical, medical industry etc. According to the principle of rapid manufacturing, the piece is manufactured layer by layer through the laser sintering or melting the fine powder. Currently, the main powder materials used are metal or polymer materials. The low melting point of these materials facilitates the melting process. However, duo to the high melting point, strong strength at high temperature and low thermal conductivity the application of ceramic materials is limited in the technology of selective laser melting. In this study, selective laser melting of the ceramic yttria stabilized zirconia by a 1μm wavelength fiber laser was explored. The influence of different laser powers and different scanning velocities on the microstructure and the deformation were analyzed, then the micro-hardness and relative density were measured. In particular, the effect of different preheat temperatures on microstructure was investigated. At the same time, the crystal structure and phase transformation during the fabrication were analyzed. Experimental results show that YSZ powder can be completely melted by the near IR fiber laser. With the optimization of the manufacturing parameters, the relative density of sample could reach 91 %. The forming of cracks and pores in the manufactured parts is rarely avoid due to the heterogeneity of distribution of energy. The energy distribution could be improved by optimizing the parameters and the crack lengths can be controlled by preheating the powder bed. In particular, the high temperature (1500 ℃, 2000 ℃ and 2500 ℃) lead the continuous vertical crack becomes messy and short. The transformation of monoclinic and cubic crystal to tetragonal crystal can be observed during the fabrication.

Selective laser melting (SLM) is a powder-based additive manufacturing technique consisting of the exact reproduction of a three dimensional computer model (generally a computer-aided design CAD file or a computer tomography CT scan) through an additive layer-by-layer strategy. Because of the high degree of freedom offered by the additive manufacturing, parts having almost any possible geometry can be produced by SLM. More specifically, with this process it is possible to build parts with extremely complex shapes and geometries that would otherwise be difficult or impossible to produce using conventional subtractive manufacturing processes. Another major advantage of SLM compared to conventional techniques is the fast cooling rate during the process. This permits the production of bulk materials with very fine microstructures and improved mechanical properties or even bulk metallic glasses. In addition, this technology gives the opportunity to produce ready-to-use parts with minimized need for post-processing (only surface polishing might be required). Recently, significant research activity has been focused on SLM processing of different metallic materials, including steels, Ti-, Ni- and Al-based alloys. However, most of the research is devoted to the parameters optimization or to feasibility studies on the production of complex structures with no detailed investigations of the structure-property correlation. Accordingly, this thesis focuses on the production and structure-property correlation of Al-12Si samples produced by SLM from gas atomized powders. The microstructure of the as-prepared SLM samples consists of supersaturated primary Al with an extremely fine cellular structure along with the residual free Si situated at the cellular boundaries. This microstructure leads to a remarkable mechanical behavior: the yield and tensile strengths of the SLM samples are respectively four and two times higher than their cast counterparts. However, the ductility is significantly reduced compared with the cast samples. The effect of annealing at different temperatures on the microstructure and resulting mechanical properties of the SLM parts has been systematically studied by analyzing the size, morphology and distribution of the phases. In addition, the mechanical properties of the SLM samples have been modeled using micro- structural features, such as the crystallite and matrix ligament sizes. The results demonstrate that the mechanical behavior of the Al-12Si SLM samples can be tuned within a wide range of strength and ductility through the use of the proper annealing treatment. The Al-Si alloys are generally used as pistons or cylinder liners in automotive applications. This requires good wear resistance and sufficient strength at the operating temperature, which ranges between 373 – 473 K. Accordingly, the tensile properties of the SLM samples were also tested at these temperatures. Changing the hatch style during SLM processing vary the texture in the material. Hence, samples with different hatch styles were produced and the effect of texture on their mechanical behavior was evaluated. The results show that the hatch style strongly influences both the mechanical properties and the texture of the samples; however no direct correlation was observed between texture and mechanical properties. The wear properties of the Al-12Si material was evaluated using pin-on-disc and fretting wear experiments. These experiments show that the as-prepared SLM samples exhibit better wear resistance than their cast counterparts and the SLM heat-treated samples. Finally, the corrosion investigations reveal that the SLM samples have similar corrosion behavior as the cast specimens under acidic conditions. A major drawback for the wide application of SLM as an industrial processing route is the limited size of the products. This is a direct consequence of the limited dimensions of the available building chambers, which allow for the production of samples with volumes of about 0.02 m3. A possible way to overcome this problem would be the use of the welding processes to join the small SLM objects to form parts with no dimensional limitations. In order to verify this possibility, friction welding was employed to join Al-12Si SLM parts. The results indicate that friction welding not only successfully permits the join materials manufactured by SLM, but also helps to significantly improve their ductility. This work clearly demonstrates that SLM can be successfully used for the production of Al-12Si parts with an overall superior performance of the mechanical and physical properties with respect to the conventional cast samples. Moreover, the mechanical properties of the SLM samples can be widely tuned in-situ by employing suitable hatch styles or ex-situ by the proper heat treatment. This might help the development of SLM for the production of innovative high-performance Al-based materials and structures with controlled properties for automotive and aerospace applications.