Graphitic carbon nitride (g-C3N4) heterojunction composites with the semiconducting metal oxides, CeO2, ZnO and TiO2 are prepared in situ by co-calcination of the precursor materials or by a solvothermal method. The structural, morphological and the optical properties of the prepared materials are studied using various microscopy and spectroscopy techniques. The synthesized composite materials, CeO2/g-C3N4, ZnO/g-C3N4 and TiO2/g-C3N4 are more efficient in the photocatalytic degradation of the water pollutants indigo carmine (IC) and atrazine than the pure metal oxide, g-C3N4, or their physical mixtures. The CeO2/g-C3N4 and ZnO/g-C3N4 composites also exhibit improved degradation efficiencies of atrazine as compared to the individual metal oxide or g-C3N4 materials. The improved photocatalytic activity of the composites are attributed to the effective electron-hole charge separation within composite heterojunction, resulting from the well matched energy levels of the metal oxide and g-C3N4. This strategy could be helpful for the synthesis of other metal oxide and g-C3N4 composites for photocatalytic applications.

With the ever-advancing technology, there is an incessant need for reliable electrochemical energy storage (EES) components that can provide desired energy and power. At the forefront of EES systems are electrochemical capacitors (ECs), also known as supercapacitors that typically have higher power and superior cycle longevity but lower energy densities than their battery counterparts. One of the routes to achieve higher energy density for ECs is using the hybrid EC configuration, which typically utilizes a redox electrode coupled with a counter double-layer type electrode. In this dissertation, both scale-up (coin-cell type) as well as scale-down (on-chip miniaturized) hybrid ECs were designed, constructed and evaluated. The first part of the dissertation comprised material identification, syntheses, and electrochemical analyses. Lithium titanate-anatase titanium oxide (Li4Ti5O12-TiO2) composites were synthesized via electrostatic spray deposition (ESD) and characterized in both half-cell and full-cell assembly against lithium and nanostructured carbon based counter electrodes, respectively. The second redox type material studied for hybrid electrochemical capacitors was ESD derived manganese oxide (MnOx). The MnOx electrodes exhibited a high gravimetric capacitance of 225F g-1 in aqueous media. Further improvement in the rate handling of the MnOx electrodes was achieved by using CNT additives. The MnOx-CNT composites were tested in full-cell assembly against activated carbon counter electrodes and tested for different anode and cathode mass ratios in order to achieve the best energy-power tradeoff, which was the second major goal of the dissertation. The optimized hybrid capacitor was able to deliver a high specific energy density of 30.3 Wh kg-1 and a maximal power density of 4kW kg-1. The last part of the dissertation focused on a scale-down miniaturized hybrid microsupercapacitor; an interdigitated electrode design was adopted in order to shorten the ion-transport pathway, and MnOx and reduced graphene oxide (rGO) were chosen as the redox and double layer components, respectively. The hybrid microsupercapacitor was able to deliver a high stack energy density of 1.02 mWh cm-3 and a maximal stack power density of 3.44 W cm-3, both of which are comparable with thin-film batteries and commercial supercapacitor in terms of volumetric energy and power densities.

Thermoelectrics is the reversible process which transforms a temperature gradient across a material into an external voltage through a phenomenon known as the Seebeck effect. This has resulted in niche applications such as solid-state cooling for electronic and optoelectronic devices which exclude the need for a coolant or any moving parts and long-lasting, maintenance-free radioisotope thermoelectric generators used for deep-space exploration. However, the high price and low efficiency of thermoelectric generators have prompted scientists to search for new materials and/or methods to improve the efficiency of the already existing ones. Thermoelectric efficiency is governed by the dimensionless figure of merit 𝑧𝑇, which depends on the electrical conductivity, thermal conductivity and Seebeck coefficient value of the material and has rarely surpassed unity. In order to address these issues, research conducted on early transition metal nitrides spearheaded by cubic scandium nitride (ScN) thin films showed promising results with high power factors close to 3000 μWm−1K−2 at 500 °C. In this thesis, rock-salt cubic chromium nitride (CrN) deposited in the form of thin films by reactive magnetron sputtering was chosen for its large Seebeck coefficient of approximately -200 μV/K and low thermal conductivity between 2 and 4 Wm−1K−1. The results show that CrN in single crystal form has a low electrical resistivity below 1 mΩcm, a Seebeck coefficient value of -230 μV/K and a power factor close to 5000 μWm−1K−2 at room temperature. These promising results could lead to CrN based thermoelectric modules which are cheaper and more stable compared to traditional thermoelectric material such as bismuth telluride (Bi2Te3) and lead telluride (PbTe). In addition, the project resulting this thesis was prompted to investigate prospective ternary nitrides equivalent to ScN with (hopefully) better thermoelectric properties. Scandium nitride has a relatively high thermal conductivity value (close to 10 Wm−1K−1), resulting in a low 𝑧𝑇. A hypothetical ternary equivalent to ScN may have a similar electronic band structure and large power factor, but with a lower thermal conductivity value leading to better thermoelectric properties. Thus the elements magnesium, titanium, zirconium and hafnium were chosen for this purpose. DFT calculations were used to simulate TiMgN2, ZrMgN2 and HfMgN2. The results show the MeMgN2 stoichiometry to be stable, with two rivaling crystal structures: trigonal NaCrS2 and monoclinic LiUN2. / <p>The series name <em>Linköping Studies in Science and Technology Licentiate Thesis</em> is incorrect. The correct series name is <em>Linköping Studies in Science and Technology Thesis</em>.</p>

<p>ZnO nanoparticles in the size range 2.5–7 nm have been synthesised by a wet chemical method where ZnO particles were grown in basic zinc acetate solution. The optical band gap increases when the size of the particles decreases. An empirical relation between the optical band gap given from absorption measurements, and particle size given from XRD measurements has been developed and compared to other similar relations found in the literature.</p><p>   Time resolved UV-Vis spectroscopy has been used to follow the growth of particles in situ in solution. The data show that the growth mechanism not can be described by a simple Oswald ripening approach and nor by an exclusive agglomeration of smaller clusters into larger particles. The growth mechanism is more likely a combination of the proposed reaction themes. The data also reveal that particle formation do not demand a heating step for formation of the commonly assumed initial cluster Zn₄O(CH₃COO)₆.</p><p>   Steady state fluorescence has been studied as a function of particle size during growth in solution. These measurements confirm what is found in the literature in that the visible fluorescence is shifted to longer wavelengths and loses in intensity as the particles grow. Some picosecond spectroscopy has also been done where the UV fluorescence has been investigated. From these measurements it is apparent that the lifetime of the fluorescence increases with particle size.</p><p>    The phonon spectrum of ZnO has been studied with Raman spectroscopy for a number of different particle sizes. From these measurements it is clear that there is a strong quenching of the phonons due to confinement for the small particles, and the only clearly observed vibration is one at 436 cm^-1 which intensity strongly increases with particle size.   </p>

ZnO nanoparticles in the size range 2.5–7 nm have been synthesised by a wet chemical method where ZnO particles were grown in basic zinc acetate solution. The optical band gap increases when the size of the particles decreases. An empirical relation between the optical band gap given from absorption measurements, and particle size given from XRD measurements has been developed and compared to other similar relations found in the literature.    Time resolved UV-Vis spectroscopy has been used to follow the growth of particles in situ in solution. The data show that the growth mechanism not can be described by a simple Oswald ripening approach and nor by an exclusive agglomeration of smaller clusters into larger particles. The growth mechanism is more likely a combination of the proposed reaction themes. The data also reveal that particle formation do not demand a heating step for formation of the commonly assumed initial cluster Zn4O(CH3COO)6.    Steady state fluorescence has been studied as a function of particle size during growth in solution. These measurements confirm what is found in the literature in that the visible fluorescence is shifted to longer wavelengths and loses in intensity as the particles grow. Some picosecond spectroscopy has also been done where the UV fluorescence has been investigated. From these measurements it is apparent that the lifetime of the fluorescence increases with particle size.     The phonon spectrum of ZnO has been studied with Raman spectroscopy for a number of different particle sizes. From these measurements it is clear that there is a strong quenching of the phonons due to confinement for the small particles, and the only clearly observed vibration is one at 436 cm-1 which intensity strongly increases with particle size.

Nanoscale particles based on the nature of building blocks often self-assemble into superstructures with distinctive spatial arrangements which can be used as functional materials for different application. Micro-phase separated hairy nanoparticle with helical hair can self-assemble to form supramolecular material which may mimic the properties and functions of the natural polymers such as protein and cellulose. Beside this hairy/core-shell nanoparticles also may find many applications such as in asymmetric catalysis, nano-fillers in tire and rubbers, model systems for biology, lithography and as sensors. In this work, we have successfully synthesized two hairy nanoparticles both of which has cross-linked polystyrene core with helical poly (3- methyl 4- vinyl pyridine) and poly (2- methoxystyrene) brushes respectively by living anionic polymerization via one-pot synthesis. NMR spectroscopy was used to determine that polymerization was successful and compositions of HNPs have the agreement with the targeted HNPs structure. By tailoring the architecture (functionalization of polymer chains, the degree of polymerization, grafting density) of HNPs, it is possible to control the final properties of the system. Differential Scanning Calorimetry was used to demonstrate the thermal properties of the synthesized HNPs which corresponds to polymer composition. Dynamic light scattering, SEM and AFM images were recorded to measure the particle size and morphology of the particles. Circular dichroism spectroscopy was used to determine the induced chirality of helical polymer brushes by complexing it with the small chiral molecule. SEM and AFM imaging were recorded to find out the morphology and hierarchically self-assembly of the hairy nanoparticle system. The synthesized particles may have great potential to successfully generate self-assembled suprastructures which can further solve the chiral resolution problem and can also find different applications.

Organic semiconductors have gained a lot of interest due to their ease of processing, low-cost and inherent mechanical flexibility. Although most of the research has been on their electronic and optical properties, knowledge of the thermal properties is important in the design of electronic devices as well. Our group has used ac-calorimetric techniques to measure both in-plane and transverse thermal conductivities of a variety of organic semiconductors including small-molecule crystals and polymer blends. For layered crystals composed of molecules with planar backbones and silylethynyl (or germylethynyl) sidegroups projecting between the layers, very high interplanar thermal conductivities have been observed, presumably implying that heat flows between layers mostly via interactions between librations on these sidegoups. Since most organic semiconducting devices require materials in thin film rather than bulk crystal form, I have focused on using the “3ω- technique” to measure the thermal resistances of thin films of this class of organic semiconductors, including bis(triisopropylsilylethynyl) pentacene (TIPS-pn), bis(triethylsilylethynyl) anthradithiophene (TES-ADT), and difluoro bis(triethylsilylethynyl) anthradithiophene (diF-TES-ADT). For each material, several films of different thicknesses have been measured to separate the effects of intrinsic thermal conductivity from interface thermal resistance. For sublimed films of TIPS-pn and diF-TES-ADT, with thicknesses ranging from less than 100 nm to greater than 4 μm, the thermal conductivities are similar to those of polymers and over an order of magnitude smaller than those of single crystals, presumably reflecting the large reduction in phonon mean-free path due to disorder in the films. On the other hand, the thermal resistances of thin (≤ 205 nm) crystalline films of TES-ADT, prepared by vapor-annealing of spin-cast films, are dominated by their interface resistances, possibly due to dewetting of the film from the substrate during the annealing process.

III-Nitride semiconductors are very promising in both electronics and optical devices. The ability of the III-Nitride semiconductors as light emitters to span the electromagnetic spectrum from deep ultraviolet light, through the entire visible region, and into the infrared part of the spectrum, is a very important feature, making this material very important in the field of light emitting devices. In fact, the blue emission from Indium Gallium Nitride (InGaN), which was awarded the 2014 Nobel Prize in Physics, is the basis of the common and important white light emitting diode (LED). Quantum dots (QDs) have properties that make them very interesting for light emitting devices for a range of different applications, such as the possibility of increasing device efficiency. The spectrally well-defined emission from QDs also allows accurate color reproduction and high-performance communication devices. The small size of QDs, combined with selective area growth allows for an improved display resolution. By control of the polarization direction of QDs, they can be used in more efficient displays as well as in traditional communication devices. The possibility of sending out entangled photon pairs is another QD property of importance for quantum key distribution used for secure communication. QDs can hold different exciton complexes, such as the neutral single exciton, consisting of one electron and one hole, and the biexciton, consisting of two excitons. The integrated PL intensity of the biexciton exhibits a quadratic dependence with respect to the excitation power, as compared to the linear power dependence of the neutral single exciton. The lifetime of the neutral exciton is 880 ps, whereas the biexciton, consisting of twice the number of charge carriers and lacks a dark state, has a considerably shorter lifetime of only 500 ps. The ratio of the lifetimes is an indication that the size of the QD is in the order of the exciton Bohr radius of the InGaN crystal making up these QDs in the InGaN QW. A large part of the studies of this thesis has been focused on InGaN QDs on top of hexagonal Gallium Nitride (GaN) pyramids, selectively grown by Metal Organic Chemical Vapor Deposition (MOCVD). On top of the GaN pyramids, an InGaN layer and a GaN capping layer were grown. From structural and optical investigations, InGaN QDs have been characterized as growing on (0001) facets on truncated GaN pyramids. These QDs exhibit both narrow photoluminescence linewidths and are linearly polarized in directions following the symmetry of the pyramids. In this work, the neutral single exciton, and the more rare negatively charged exciton, have been investigated. At low excitation power, the integrated intensity of the PL peak of the neutral exciton increases linearly with the excitation power. The negatively charged exciton, on the other hand, exhibits a quadratic power dependence, just like that of the biexciton. Upon increasing the temperature, the power dependence of the negatively charged exciton changes to linear, just like the neutral exciton. This change in power dependence is explained in terms of electrons in potential traps close to the QD escaping by thermal excitation, leading to a surplus of electrons in the vicinity of the QD. Consequently, only a single exciton needs to be created by photoexcitation in order to form a negatively charged exciton, while the extra electron is supplied to the QD by thermal excitation. Upon a close inspection of the PL of the neutral exciton, a splitting of the peak of just below 0.4 meV is revealed. There is an observed competition in the integrated intensity between these two peaks, similar to that between an exciton and a biexciton. The high energy peak of this split exciton emission is explained in terms of a remotely charged exciton. This exciton state consists of a neutral single exciton in the QD with an extra electron or hole in close vicinity of the QD, which screens the built-in field in the QD. The InGaN QDs are very small; estimated to be on the order of the exciton Bohr radius of the InGaN crystal, or even smaller. The lifetimes of the neutral exciton and the negatively charged exciton are approximately 320 ps and 130 ps, respectively. The ratio of the lifetimes supports the claim of the QD size being on the order of the exciton Bohr radius or smaller, as is further supported by power dependence results. Under the assumption of a spherical QD, theoretical calculations predict an emission energy shift of 0.7 meV, for a peak at 3.09 eV, due to the built-in field for a QD with a diameter of 1.3 nm, in agreement with the experimental observations. Studying the InGaN QD PL from neutral and charged excitons at elevated temperatures (4 K to 166 K) has revealed that the QDs are surrounded by potential fluctuations that trap charge carriers with an energy of around 20 meV, to be compared with the exciton trapping energy in the QDs of approximately 50 meV. The confinement of electrons close to the QD is predicted to be smaller than for holes, which accounts for the negative charge of the charged exciton, and for the higher probability of capturing free electrons. We have estimated the lifetimes of free electrons and holes in the GaN barrier to be 45 ps and 60 ps, in consistence with excitons forming quickly in the barrier upon photoexcitation and that free electrons and holes get trapped quickly in local potential traps close to the QDs. This analysis also indicates that there is a probability of 35 % to have an electron in the QD between the photoexcitation pulses, in agreement with a lower than quadratic power dependence of the negatively charged exciton. InN is an attractive material due to its infrared emission, for applications such as light emitters for communication purposes, but it is more difficult to grow with high quality and low doping concentration as compared to GaN. QDs with a higher In-composition or even pure InN is an interesting prospect as being a route towards increased quantum confinement and room temperature device operation. For all optical devices, p-type doping is needed. Even nominally undoped InN samples tend to be heavily n-type doped, causing problems to make pn-junctions as needed for LEDs. In our work, we present Mg-doped p-type InN films, which when further increasing the Mg-concentration revert to n-type conductivity. We have focused on the effect of the Mg-doping on the light emission properties of these films. The low Mg doped InN film is inhomogeneous and is observed to contain areas with n-type conductivity, so called n-type pockets in the otherwise p-type InN film. A higher concentration of Mg results in a higher crystalline quality and the disappearance of the n-type pockets. The high crystalline quality has enabled us to determine the binding energy of the Mg dopants to 64 meV. Upon further increase of the Mg concentration, the film reverts to ntype conductivity. The highly Mg doped sample also exhibits a red-shifted emission with features that are interpreted as originating from Zinc-Blende inclusions in the Wurtzite InN crystal, acting as quantum wells. The Mg doping is an important factor in controlling the conductivity of InN, as well as its light emission properties, and ultimately construct InN-based devices. In summary, in this thesis, both pyramidal InGaN QDs and InGaN QDs in a QW have been investigated. Novel discoveries of exciton complexes in these QD systems have been reported. Knowledge has also been gained about the challenging material InN, including a study of the effect of the Mg-doping concentration on the semiconductor crystalline quality and its light emission properties. The outcome of this thesis enriches the knowledge of the III-Nitride semiconductor community, with the long-term objective to improve the device performance of III-Nitride based light emitting devices.

The thesis focuses on exploring the sub-grain structure in stainless steel 316L prepared by additive manufacturing (AM). Two powder-bed based AM methods are involved: selective laser melting (SLM) and electron beam melting (EBM). It is already known that AM 316L has heterogeneous property and hierarchy structure: micro-sized melt pools, micro-sized grains, nano-sized sub-grain structure and nano-sized inclusions. Yet, the relation among these structures and their influence on mechanical properties have not been clearly revealed so far. Melt pool boundaries having lower amount of sub-grain segregated network structures (Cellular structure) are weaker compared to the base material. Compared with cell boundaries, grain boundaries have less influence on strength but are still important for ductility. Cell boundaries strengthen the material without losing ductility as revealed by mechanical tests. Cellular structure can be continuous across the melt pool boundaries, low angle sub-grain boundaries, but not grain boundaries. Based on the above understanding, AM process parameters were adjusted to achieve customized mechanical properties. Comprehensive characterization were carried out to investigate the density, composition, microstructure, phase, magnetic permeability, tensile property, Charpy impact property, and fatigue property of both SLM and EBM SS316L at room temperature and at elevated temperatures (250°C and 400°C). In general, SLM SS316L has better strength while EBM SS316L has better ductility due to the different process conditions. Improved cell connection between melt pools were achieved by rotating 45° scanning direction between each layer compared to rotating 90°. Superior mechanical properties (yield strength 552 MPa and elongation 83%) were achieved in SLM SS316L fabricated with 20 µm layer thickness and tested in the building direction. Y2O3 added oxide dispersed strengthening steel (ODSS) were also prepared by SLM to further improve its performance at elevated temperatures. Slightly improved strength and ductility (yield strength 574 MPa and elongation 90%) were obtained on 0.3%Y2O3-ODSS with evenly dispersed nanoparticles (20 nm). The strength drops slightly  but ductility drops dramatically at elevated temperatures. Fractographic analysis results revealed that the coalescence of nano-voids is hindered at room temperature but not at elevated temperatures. The achieved promising properties in large AM specimens assure its potential application in nuclear fusion. For the first time, ITER first wall panel parts with complex inner pipe structure were successfully fabricated by both SLM and EBM which gives great confidence to application of AM in nuclear industry. / <p>At the time of the doctoral defense, the following papers were unpublished and had a status as follows: Paper 4: Manuscript. Paper 5: Manuscript.</p>

There are multiple applications for polymers: our bodies are built of them, plastic bags and boxes used for storage are composed of them, as are the shells for electronics, TVs, computers, clothes etc. Many polymers are cheap, and easy to manufacture and process which make them suitable for disposable systems. The choice of polymer to construct an object will therefore highly influence the properties of the object itself. The focus of this thesis is the application of commonly used polymers to solve some challenges regarding integration of electrodes in electrokinetic devices and 3D printing. The first part of this thesis regards electrokinetic systems and the electrodes’ impact on the system. Electrokinetic systems require Faradaic (electrochemical) reactions at the electrodes to maintain an electric field in an electrolyte. The electrochemical reactions at the electrodes allow electron-to-ion transduction at the electrode-electrolyte interface, necessary to drive a current at the applied potential through the system, which thereby either cause flow (electroosmosis) or separation (electrophoresis). These electrochemical reactions at the electrodes, such as water electrolysis, are usually problematic in analytical systems and systems applied in biology. One solution to reduce the impact of water electrolysis is by replacing metal electrodes with electrochemically active polymers, e.g. poly(3,4-ethylenedioxythiophene) (PEDOT). Paper 1 demonstrates that PEDOT electrodes can replace platinum electrodes in a gel electrophoretic setup. Paper 2 reports an all-plastic, planar, flexible electroosmotic pump which continuously transports water from one side to the other using potentials as low as 0.3 V. This electroosmotic pump was further developed in paper 3, where it was made into a compact and modular setup, compatible with commercial microfluidic devices. We demonstrated that the pump could maintain an alternating flow for at least 96 h, with a sufficient flow of cell medium to keep cells alive for the same period of time. The second part of the thesis describes the use of 3D printers for manufacturing prototypes and the material requirements for 3D printing. Protruding and over-hanging structures are more challenging to print using a 3D printer and usually require supporting material during the printing process. In paper 4, we showed that polyethylene glycol (PEG), in combination with a carbonate-based plasticizer, functions well as a 3D printable sacrificial template material. PEG2000 with between 20 and 30 wt% dimethyl carbonate or propylene carbonate have good shear-thinning rheology, mechanical and chemical stability, and water solubility, which are advantageous for a supporting material used in 3D printing. The advances presented in this thesis have solved some of the challenges regarding electrokinetic systems and prototype manufacturing. Hopefully this will contribute to the development of robust, disposable, low-cost, and autonomous electrokinetic devices. / Polymera material finns överallt omkring oss; våra kroppar är uppbyggda av dem,plastpåsarna och burkarna vi förvarar vår mat av består av dem, våra kläder och andra tingsom finns i vår vardag är uppbyggda av olika typer av polymerer. En polymer är uppbyggd aven repetitiv sekvens av identiska grupper, de kan liknas vid en mönsterrapport vilken är denminsta del som man behöver repetera för att få mönstret. Beroende på hur rapporten ser ut såförändras utseendet av mönstret. Hos en polymer påverkar sammansättningen av denrepetitiva gruppen (rapporten) egenskaperna av materialet och polymerer kan vara allt frånhårda och robusta, till flexibla och elektriskt ledande. Arbetet som presenteras i den häravhandlingen berör hur funktionen av olika system påverkas av att man använder sig avpolymerer istället för konventionella material. Första delen av avhandlingen handlar om integrering av elektronik i system som innehållervätska. När vätskor, laddade partiklar, molekyler och joner rör på sig på grund av ett yttreelektriskt fält, så kallas detta för elektrokinetik. Detta kan användas för att pumpa vätska ikanaler som är mindre än 0.2 mm, genom så kallad elektroosmos, samtidigt kommermolekyler med olika laddning att börja separera, så kallad elektrofores. Elektroosmos användsinom t.ex. analytisk kemi för injektion och transport av vätskor. Elektrofores används inombl.a. rättsvetenskap och molekylärbiologi för att separera makromolekyler, så som DNA ochproteiner, med avseende på deras storlek och laddning. I dessa system använder man sig oftastav metallelektroder. När en spänning läggs till ett par metallelektroder som är i kontakt med vatten kommer denhuvudsakliga reaktionen att vara spjälkning av vatten, så kallad vattenelektrolys. Spjälkningav vatten innebär att det bildas vät-och syrgas samt att pH börjar ändras. Gaserna som bildaskan bryta kopplingen mellan elektroderna och därmed stoppar strömmen, så som sker när mandrar ut sladden för t.ex. en elvisp. Förändringar i pH kan t.ex. påverka biologiska provernegativt, så som proteiners funktion och kan leda till celldöd, men kan också minska flödenaen elektroosmotisk pump kan generera. Det finns flera olika sätt hur man kan hanteravattenelektrolys i system med metallelektroder, så som användning av en pH-buffer. Arbetet iden här avhandlingen visar vad som händer om man ersätter metallelektroder med elektrisktledande plastelektroder. I detta fall har metallelektroderna ersatts av den elektriskt ledandepolymeren PEDOT vilket resulterar i att , där man istället för generera gas och pHviförändringar, så förflyttar man joner mellan elektroden och omgivande lösning. Ledandepolymerer är billiga och enkla att tillverka vilket gör dem lämpliga för engångssystem. förändringar, så förflyttar man joner mellan elektroden och omgivande lösning. Ledandepolymerer är billiga och enkla att tillverka vilket gör dem lämpliga för engångssystem.I den här avhandlingen visas följande exempel där metallelektroder ersatts av ledandeplastelektroder: Gelelektrofores (separation av proteiner i en gel), (se papper 1), tyg som kanpumpa vatten (plan elektroosmotisk pump, se papper 2) och en kompakt pump som inte ärstörre än ett kaffemått, som enkelt kan kopplas till befintliga sprutkopplingar och som kananvändas för att kontrollera flödet över t.ex. celler (se papper 3). Andra delen av avhandlingen handlar om 3D skrivare och hur materialval påverkarutskriften och designen. 3D skrivare är ett bra alternativ för att snabbt och billigt kunnaproducera prototyper och funktionella individanpassade objekt i varierande storlekar.3D skrivare kan beskrivas som en avancerad spritsmaskin där material läggs lager på lager föratt bygga upp det slutgiltiga objektet utifrån en datorgenererade 3D model. Detta förändrarhelt hur man designar objekt och vilka möjliga strukturer och material man kan använda sigav jämfört än då man till exempel använder sig av svarv eller fräs för tillverkning. Det finnsflera olika typer av 3D skrivare, t.ex. smältplastskrivare (den typ som man kan se i flertaletaffärer idag) och den variant som använts i den här avhandlingen, en sprutbaserad. Ensprutbaserad 3D skrivare kan hantera många olika typer av material så länge dessa kan fyllas ien spruta och tryckas ut genom en nål. Det färdiga resultat kan därmed bli mycket olikaberoende på vilka material som använts. Överhängande och utstickande strukturer kan vara komplicerade att skriva ut med en3D skrivare. Utskrift av dessa strukturer kan underlättas genom att man skriver ut en temporärstruktur i ett annat material, ett offermaterial. Offermaterialet fungerar som en mall eller stödtill det slutgiltiga objektet och tas bort (offras) när övriga delar av objektet är klara. I den häravhandlingen beskrivs hur ett offermaterial baserat på polyetylen glykol (PEG, vanligtförekommande i t.ex. schampo och läkemedel) och en mjukgörare kan anpassas för attfungera tillsammans med en sprutbaserad 3D skrivare (se papper 4) för att skriva ut strukturerfrån 0,2 mm och uppåt. Arbetet i den här avhandlingen visar användningen av den ledande polymeren PEDOT i ettelektroforessystem och en elektroosmotisk pump. Detta kan förhoppningsvis underlättautvecklingen av dessa system till att bli mindre, smidigare, snabbare och billigare. Den andradelen presenterar ett vattenlösligt, PEG-baserat material som kan användas som stöd till andramaterial i sprutbaserade 3D utskrifter för att underlätta tillverkningen av 3D utskrivna objekt.