<p>Composite materials used in the aviation industry are known to be more complex than their metallic predecessors. This impacts not only the design and manufacturing of composite structures, but also the failure studies when these structures fail and break (as may be the case in an aircraft accident). Additionally, when under combustion, composite materials introduce potential health hazards. At elevated temperatures, the fibers can be released, presenting an inhalation hazard. Similarly, the matrix decomposition results in a series of potentially toxic byproducts. When encountering composite fires at aircraft accident sites, a series of protocols have been delineated by the corresponding agencies. These include wearing personal protective equipment as well as the application of so-called fixant solutions over the burning composites, with the latter being the focus of this study. The purpose of the fixant solutions is to provide a film of protection that – in essence – holds down small fibers and prevents them from becoming airborne. While the use of fixant solutions is necessary to protect the health of individuals in the vicinity of burnt composites, the potential detrimental impact the application thereof has on fractographic evidence should also be considered. Experts in the field have voiced concerns regarding the use of fixants, outlining that these chemicals may wash evidence away, cover up evidence, or interfere with imaging methods needed during the failure analysis. The purpose of the conducted research, thus, was to compare the relative impact of four commonly used fixant solutions – namely water, wetted water, polyacrylic acid (PAA), as well as a mixture of water and floor wax – on fractographic features of failed carbon fiber/epoxy composite specimens. Specifically, fractographic evidence of two forms of damage – impact and tension – were evaluated. With this goal, the methodology included steps to manufacture the specimens of interest, introduce the two forms of damage, burn the specimens, apply fixants, and perform the microscopic analysis via a scanning electron microscope (SEM). The fractographic evidence prior and after the application of fixant was evaluated qualitatively and quantitatively. The results showed that the evaluated fixants did influence the fracture surfaces imaged, and in certain cased obscured evidence of interest. Additionally, differences between the fixants were ascertained for both forms of damage evaluated. The water treatment was found to perform the best, minimizing the disruption of evidence. Nonetheless, while the study did answer the research questions and the different treatments were compared, additional areas of research and factors that should be considered were identified. </p>

Automated shuttles are designed to provide a clean transportation and improve access to areas such as where travelers have to walk long distances to/from bus stops. The introduction of automated shuttles in the road network might affect the safety of pedestrians and cyclists as well as traffic performance of motorized vehicles. Several demonstration trials are being conducted to study how automated shuttles operate in real traffic conditions, but they are limited to few vehicles and evaluations of traffic effects at higher penetration rates are not possible. Traffic simulation is a tool that can be used to study effects on traffic performances at different penetration rates of e.g., automated shuttles. However, automated shuttles have not yet been modeled, calibrated, and validated in microscopic traffic simulation tools. Therefore, the objective of this thesis is to model, calibrate and validate automated shuttle’s behavior using the simulation tool SUMO and data collected from the demonstration trial on the area of campus Valla Linköping University, Sweden. The pilot study consists of two automated shuttles, and they operate on a 2.1 km fixed route. The collected data by one of the automated shuttles is analyzed with a focus on the free driving behavior. The analysis shows that the automated shuttle has different maximum operation speeds at different locations and defining one value for the maximum speed when setting up the simulation is not enough. Therefore, virtual speed limits are derived by mimicking the maximum operation speed of the shuttle from the data and used to define segment specific speed limits in the simulation. Additionally, the data is used to calibrate the acceleration and deceleration parameters. The Krauss and the IDM car-following models have been investigated by calibrating the acceleration and deceleration parameters for the free driving situation. The results indicate that both the Krauss and IDM car-following models follows the general trend of the speed and acceleration profiles. The speed profiles produced with the IDM model have smoother profiles at the start and end of acceleration and deceleration phases while in Krauss model the transition of the speed change is more direct and there are in principle no delays for reaction. Although the IDM model performs slightly better for the free driving situation, it can be of interest to consider both models for the calibration of interactions with other roads users since both models are able to capture the general trend of the speed and acceleration profiles. / <p>Examensarbetet är utfört vid Institutionen för teknik och naturvetenskap (ITN) vid Tekniska fakulteten, Linköpings universitet</p>

Vehicle velocity distributions are of utmost relevance for the efficiency, safety, and sustainability of road traffic. Yet, due to technical limitations, they are often empirically analyzed using spatiotemporal averages. Here, we instead study a novel set of microscopic traffic data from Dresden comprising 346 million data points with a resolution of one vehicle from 145 detector sites with a particular focus on extreme events and distribution tails. By fitting q-exponential and Generalized Extreme Value distributions to the right flank of the empirical velocity distributions, we establish that their tails universally exhibit a power-law behavior with similar decay exponents. We also find that q-exponentials are best suitable to model the vast extent to which speed limit violations in the data occur. Furthermore, combining velocity and time headway distributions, we obtain estimates for free flow velocities that always exceed average velocities and sometimes even significantly exceed speed limits. Likewise, congestion effects are found to play a very minor, almost negligible role in traffic flow at the detector sites. These results provide insights into the current state of traffic in Dresden, hinting toward potentially necessary policy amendments regarding road design, speed limits, and speeding prosecution. They also reveal the potentials and limitations of the data set at hand and thereby lay the groundwork for further, more detailed traffic analyses.

This dissertation develops a framework for modeling vehicle emissions microscopically. In addition, the framework is utilized to develop the VT-Micro model using a number of data sources. Key input variables to the VT-Micro model include instantaneous vehicle speed and acceleration levels. Estimating accurate mobile source emissions is becoming more and more critical as a result of increasing environmental problems in large metropolitan urban areas. Current emission inventory models, such as MOBILE and EMPAC, are designed for developing large scale inventories, but are unable to estimate emissions from specific corridors and intersections. Alternatively, microscopic emission models are capable of assessing the impact of transportation scenarios and performing project-level analyses. The VT-Micro model was developed using data collected at the Oak Ridge National Laboratory (ORNL) that included fuel consumption and emission rate measurements (CO, HC, and NOx) for five light-duty vehicles (LDVs) and three light-duty trucks (LDTs) as a function of the vehicle's instantaneous speed and acceleration levels. The hybrid regression models predict hot stabilized vehicle fuel consumption and emission rates for LDVs and LDTs. The model is found to be highly accurate compared to the ORNL data with coefficients of determination ranging from 0.92 to 0.99. The study compares fuel consumption and emission results from MOBILE5a, VT-Micro, and CMEM models. The dissertation presents that the proposed VT-Micro model appears to be good enough in terms of absolute light-duty hot stabilized normal vehicle tailpipe emissions. Specifically, the emission estimates were found to be within the 95 percent confidence limits of field data and within the same level of magnitude as the MOBILE5a model estimates. Furthermore, the proposed VT-Micro model was found to reflect differences in drive cycles in a fashion that was consistent with field observations. Specifically, the model accurately captures the increase in emissions for aggressive acceleration drive cycles in comparison with other drive cycles. The dissertation also presents a framework for developing microscopic emission models. The framework develops emission models by aggregating data using vehicle and operational variables. Specifically, statistical techniques for aggregating vehicles into homogenous categories are utilized as part of the framework. In addition, the framework accounts for temporal lags between vehicle operational variables and vehicle emissions. Finally, the framework is utilized to develop the VT-Micro model version 2.0 utilizing second-by-second chassis dynamometer emission data for a total of 60 light duty vehicles and trucks. Also, the dissertation introduces a procedure for estimating second-by-second high emitter emissions. This research initially investigates high emitter emission cut-points to verify clear definitions of high emitter vehicles (HEVs) and derives multiplicative factors for newly developed EPA driving cycles. Same model structure with the VT-Micro model is utilized to estimate instantaneous emissions for a total of 36 light duty vehicles and trucks. Finally, the dissertation develops a microscopic framework for estimating instantaneous vehicle start emissions for LDVs and LDTs. The framework assumes a linear decay in instantaneous start emissions over a 200-second time horizon. The initial vehicle start emission rate is computed based on MOBILE6's soak time function assuming a 200-second decay time interval. The validity of the model was demonstrated using independent trips that involved cold start and hot start impacts with vehicle emissions estimated to within 10 percent of the field data. The ultimate expansion of this model is its implementation within a microscopic traffic simulation environment in order to evaluate the environmental impacts of alternative ITS and non-ITS strategies. Also, the model can be applied to estimate vehicle emissions using instantaneous GPS speed measurements. Currently, the VT-Micro model has been implemented in the INTEGRATION software for the environmental assessment of operational-level transportation projects. / Ph. D.

京都大学 / 新制・課程博士 / 博士(工学) / 甲第24902号 / 工博第5182号 / 新制||工||1989(附属図書館) / 京都大学大学院工学研究科材料化学専攻 / (主査)教授 三浦 清貴, 教授 田中 勝久, 教授 藤田 晃司 / 学位規則第4条第1項該当 / Doctor of Philosophy (Engineering) / Kyoto University / DFAM

No description available.

No description available.

No description available.

No description available.

No description available.