One of the most significant issues in nanocomposite performance is improving the dispersion of carbon nanotubes (CNTs) in thermosetting or thermoplastic polymers in order to gain good mechanical properties. Several studies have investigated the fabrication of nanocomposites based on carbon nanotubes and analysed properties, but there is still insufficient data on their structure-property relationships. This thesis has investigated the central importance of stress transfer Raman studies in epoxy composites reinforced with single-walled carbon nanotubes (SWCNTs), double-walled carbon nanotubes (DWCNTs) and multiwall carbon nanotubes (MWCNTs) to elucidate the reinforcing ability of the CNTs in an epoxy matrix. This project was undertaken to synthesise and characterize MWCNTs and determine the effect of different weight fractions of untreated MWCNTs on the stress transfer efficiency at the MWCNTS / epoxy interface and on the stiffness of the thermomechanical properties of the MWCNTS / epoxy composites. It was undertaken to assess the stress transfer efficiency at the CNT / epoxy interface and at the inter-walls of the CNTs with tensile deformation and with cyclic loading.Optimized conditions of the injection chemical vapour deposition method (CVD), such as long injection times were applied to produce MWCNTs with a high yield, high aspect ratio and well-defined G' Raman peak. The morphology and size of CNTs were observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) while their thermal stability was examined by Thermogravimetric analysis (TGA). Both Raman spectroscopy and mechanical testing (static and dynamic) were utilized in this study. The Raman spectroscopy research consisted of following the G'-band frequency and linewidth as well as the intensity of radial breathing modes (RBMs) during tensile deformation. The stress-induced Raman shifts in the nanocomposites have been shown to be controlled by the number of carbon nanolayers. A theory has been developed to determine and simulate the stress transfer efficiency parameter, (k_i) for MWCNTs. Tensile tests and dynamic mechanical testing were used to assess the mechanical properties of the nanocomposites.The most obvious finding to be drawn from the present study is that the reinforcement of the epoxy resin with different loadings of MWCNTs is useful, but the best reinforcement was at low loadings of MWCNTs. One of the more significant findings to emerge from this study is that (k_i) between the inner walls of the DWCNTs and MWCNTs are quite similar (~0.7), which suggest that (k_i) may be similar for all CVD MWCNTs and DWCNTs. The second major finding was that there were RBM intensity variations for the SWCNTs and DWCNTs in the hot-cured epoxy composites and that for the DWCNTs both the inner and outer nanotube walls are stressed during deformation

Thesis (M.Sc. (Chemistry)) -- University of Limpopo, 2015 / The study has focused on the effects of different acids treatments on the nanostructure of MWCNTs; doping metal oxides (copper oxide (CuO), Iron (III) oxide (Fe2O3), nickel oxide (NiO) and cobalt oxide (Co3O4)) on MWCNTs and investigates their electrochemical hydrogen and energy storage capabilities. Fourier transform infrared (FTIR) confirmed the formation of functional groups on the surface of the acid treated MWCNTs. X-ray diffraction (XRD) showed that the graphitic structure of the MWCNTs was retained after treatment with mild acids (nitric acid (HNO3), hydrogen peroxide (H2O2), a mixture of the acids, hydrogen peroxide: nitric acid (H2O2:HNO3) and hydrogen peroxide: sulfuric acid (H2O2:H2SO4)). Transmission electron microscopy (TEM) confirms the removal of bamboo carbon structures inside the inner tubes of the MWCNTs after treatment with mild acids. Brunauer-Emmet- Teller (BET) showed an increase in the surface area of mild acids treated MWCNTs. Thermogravimetric analysis (TGA) results demonstrated that the thermal stability of MWCNTs increases after treatment with mixtures of the acids. Different metal oxides treated at different temperatures were incorporated into MWCNTs (treated by a mixture of H2O2:HNO3). X-ray diffraction (XRD), scanning electron microscopy (SEM) and Transmission electron microscopy (TEM) confirmed the presence of different metal oxides inside/on the surface of the acid treated MWCNTs. The MWCNTs treated by H2O2:HNO3 gave both the highest discharge capacity (72.63 mAh/g) and capacitance (8.61 F/g), as compared to the other electrode materials. The improved hydrogen storage capacity and specific capacitance can be attributed to high surface area, wider pore size distribution and the amount of functional groups on the surface of H2O2:HNO3-treated MWCNTs; with the functional groups acting as electron transmitters. The 5wt.% CuO@300oC-MWCNTs composite showed the highest hydrogen storage capacity of 159 mAh/g. This capacity was further improved by addition of manganese oxide resulting in the highest discharge capacity of 172 mAh/g (which is equivalent to 0.64 wt.% of hydrogen stored). The highest specific capacitance of 9.70 F/g was obtained on 5wt% Fe2O3@400oCMWCNTs composite.

In this thesis, bulk and local scale spectroscopic and microscopic tools have been applied to investigate the purified raw material of SWCNT and synthesized MWBNNT, BN-nanocapsules, B-doped SWCNT and SiC nanostructures. Using bulk scale sensitive techniques, including optical absorption spectroscopy, Raman spectroscopy, high-resolution electron energy-loss spectroscopy, the average response of the whole sample is obtained. On the other hand, on a local scale transmission and scanning electron microscopy as well as TEM-electron energy-loss spectroscopy provide information on single tubes or other nanostructures. First, diverse chemical and oxidation methods for the purification of as-produced SWCNT were presented. Purified samples were investigated using TEM and OAS. The analysis of the optical absorption spectra in the UV-Vis energy range revealed that some of the chemical treatments are harmful to nanotubes. In contrast to the chemical treatments an oxygen burning procedure was used on the raw material in high vacuum and a temperature range 450?650oC. The purification processes of SWCNT by HNO3 and oxygen burning procedures resulted in SWCNT comprised of selected diameters and a reduced diameter distribution. Both HNO3 and oxygen burning treatments can be used to selectively remove SWCNT with smaller diameters from the samples. In addition, an adapted substitution reaction was used for the synthesis of multiwall boron nitride nanotubes. It was shown that the IR-response of MWBNNT can be used as a fingerprint to analyse MWBNNT. As in h-BN for the analysis one has to be aware of the sample texture and the LO-TO splitting of the IR-active modes. TEM images and B1s and N 1s excitation edges of the grown material reveal the presence of multiwall BN nanotubes with an inner diameter of 3.1 nm and with a larger interplanar distance than in h-BN. The electronic properties of the multiwall BN nanotubes as derived from the q-dependent dielectric function e(w,q) are dominated by the band structure of the hexagonal-like BN sheets, as revealed by the large degree of momentum dispersion observed for the p and s+p plasmons, in agreement with that previously reported for different graphitic allotropic forms. Moreover, a fast and highly efficient synthesis route to produce BN nanocapsules with a narrow size distribution was developed. This was achieved by an adapted substitution process using SWCNT as templates followed by a rapid cooling treatment. The IR responses reveal the strong dipole active fingerprint lines of h-BN with distinct differences, which are due to texturing effects and which highlight the BN nanocapsules potential application as a reference source when deriving the sp2 to sp3 ratio in BN species due to their random orientation Furthermore, the idea of substitution was used for the systematic studies of B-doped SWCNT. The experiments carried out have resulted in 1, 5, 10, and 15 % boron incorporated into the single wall carbon nanotubes. Core level excitation spectroscopy of the B1s and C1s edges revealed that the boron atoms substitute carbon atoms in the tube lattice keeping an sp2-like bond with their nearest C neighbour atoms. Our results show that a simple rigid band model as has been applied previously to intercalated SWCNT is not sufficient to explain the changes in the electronic properties of highly doped B-SWCNT and a new type of a highly defective BC3 SWNT with new electronic properties is obtained. Finally, different silicon carbide nanostructures were produced. The spectroscopic and microscopic data led to a good understanding of the formation process. NH3 acts as a source of hydrogen that plays a key role in the formation of the structures through its ability to decompose SiC at high temperature such that along with the stacking faults that arise from the many polytypes of SiC the produced SiC nanorods become porous then hollow and eventually are completely decomposed.

Next generation polymer composites that utilize the high electrical conductivity and tensile strength of carbon nanotubes are of interest. To effectively disperse carbon nanotubes into polymers, a more fundamental understanding of the polymer/nanotube interface is needed. This requires the development of new analytical methods and techniques for measuring the adhesion between a single molecule and the sidewalls of carbon nanotubes. Atomic Force Microscopy is an integral tool in the characterization of materials on the nanoscale. The objectives of this research were to: 1) characterize the binding force between single molecules and the backbone of a single walled carbon nanotube (SWNT), and 2) measure and interpret the mechanical response of carbon-based nano-objects to compressive loads using an atomic force microscope. To identify chemical moieties that bind strongly to the sidewall of the nanotubes, two experimental approaches have been explored. In the first, force volume images of SWNT paper were obtained using gold-coated AFM tips functionalized with terminally substituted alkanethiols and para-substituted arylthiols. Analysis of these images enabled quantification of the adhesive interactions between the functionalized tip and the SWNT surface. The resultant adhesive forces were shown to be dependent upon surface topography, tip shape, and the terminal group on the alkanethiol. The mechanical response of several single- and multi-walled carbon nanotubes under compressive load was examined with an AFM. When the scanner, onto which the substrate has been mounted, was extended and retracted in a cyclic fashion, cantilever deflection, oscillation amplitude and resonant frequency were simultaneously monitored. By time-correlating cantilever resonance spectra, deflection and scanner motion, precise control over the length of nanotube in contact with the substrate, analogous to fly-fishing was achieved. This multi-parameter force spectroscopy method is applicable for testing the mechanical and interfacial properties of a wide range of nanoscale objects. This research has led to a clearer understanding of the chemistry at the nanotube/polymer interface, as well as the mechanical response of nanoscale materials. A new force spectroscopic tool, multi-parameter force spectroscopy, should be extremely helpful in characterizing the mechanical response of a myriad of nanoscale objects and enable nanoscale devices to become a reality.

The main motivation in this thesis is to compare the conformation and charge transport in conducting polymers and carbon nanotubes (CNTs) and to investigate those physical properties in their combined form of nanocomposites. It is known that both conducting polymers and carbon nanotubes are intrinsically 1-dimensional systems which consist of delocalized π-electrons. However, the main difference between these is the fact that flexibility of conducting polymers can be varied depending on the extent of conjugation while CNTs are rigid. Hence a comparison of electronic properties as correlated to their morphology has been carried out and their individual role in nanocomposites is further studied. The thesis consists of 6 chapters and appendix. Chapter 1 consists of brief introduction of general properties of both conducting polymers, CNTs and their nanocomposites. Chapter 2 deals with the sample preparation and experimental techniques used for the work. Chapter 3 elaborates on the conformational / structural studies on the systems. Chapter 4 focuses on the transport measurements to study the electronic properties of the samples. Chapter 5 reveals the magnetic properties of these systems which can be applied in technological devices. And chapter 6 gives the conclusion and future directions of the work being done. Chapter 1: Nanocomposites represent a guest-host matrix consisting of easily processible functionalized conjugated polymer as host, incorporating carbon nanotubes as fillers with versatile electronic and magnetic properties, which provide a wide range of technological applications. The conformation, charge dynamics as well as magnetic properties of these conducting polymers and carbon nanotubes, and various aspects of transport mechanism and spin dynamics present in the nanocomposite matrix are studied and presented in a consistent framework. Chapter 2: The multiwall carbon nanotubes (MWNTs) are grown by thermal chemical vapor deposition (CVD). The MWNTs are dispersed in solution of conducting polymers by ultrasonication and then the suspension is cast on glass substrate and slowly dried by moderate heating. Once dried completely, the free-standing films of thickness 15-25 μm are peeled off the substrate for measurements. The MWNTs, above a certain concentration, form an interconnected network in the 3-dimensional polymer matrix, following percolation mechanism. The disorder is brought into the system mainly by bundling of tubes and bundle intersections. The morphology and conformation of the samples are studied by SEM, TEM and small angle X-ray scattering (SAXS) techniques. Chapter 3: Small angle X-ray scattering (SAXS) studies in polymeric systems are carried out to probe local nanoscale morphology at various length scales to show the correlation among conformation and assembly of chains. Small angle X-ray scattering (SAXS) studies are carried out in poly [2-methoxy5-(2’–ethyl-hexyloxy)-1,4-phenylene vinylene] (MEH-PPV) solution of varying conjugation lengths as well as different solvents. By increasing the extent of πconjugation from 30 to 100 %, the persistence length increases by a factor of three. Moreover, a pronounced second peak in the pair distribution function is observed in fully conjugated chain, at larger length scales which indicates that the chain segments tend to self-assemble as the conjugation along the chain increases. The chain assembly and aggregation are further studied for suspensions of MWNTs in polyethylene dioxythiophene-polystyrene (PEDOT-PSS) with aqueous medium and DMSO (dimethyl sulphoxide). The SAXS profile of MWNT dispersion in aqueous PEDOT-PSS clearly show rigid-rod feature of the individual nanotubes evident by the q-1 behavior at short ranges. The crossover from q-1 to q-2 in the longer range further suggest that the suspension consists of individual nanotubes, nanotubes bundles and aggregates that give rise to a 3-dimensonal meshwork of intersecting tubes and ropes. For the MWNT dispersion in PEDOT-PSS with DMSO, however, such q-1 behavior is absent; which evidently shows that the rods are not isolated in the solution and are rather agglomerated. How these conformations affect the electrical and magnetic properties of these systems are studied further in Chapter 4. Chapter 4: Transport mechanism in single wall carbon nanotubes (SWNT), MWNT pellets, and nanocomposite films of MWNT and PEDOT-PSS is studied. The positive and negative magnetoresistance (MR) data in various SWNT samples are analyzed by taking into account the electron-electron interaction (EEI) contribution, in addition to the weak localization (WL) regime. The contribution from EEI to the total MR is confirmed from the universal scaling of MC relation showing that EEI plays a significant role at higher fields and lower temperatures. Intrinsic parameters like inelastic scattering length extracted for barely metallic sample follows the T-3/4 dependence due to inelastic electron-electron scattering in the dirty limit. Conductivity and magnetoresistance (MR) measurements on nanocomposite films with varying MWNT content (0.03 - 3 %) are performed at a field range 0-11 Tesla, and temperature range 1.3–300 K. The temperature dependence of resistance above 4 K suggests a Coulomb-gap variable range hopping (CG-VRH) transport in the network. Alhough solely negative MR (~ 5-6 %) is observed for pristine MWNT pellets; the nanocomposite films show a combination of large negative MR (~ 80 %) at T < 4 K, and a comparatively weaker positive MR (~ 30 %) for T > 4 K. This suggest that there are two mechanism interplaying and dominant at different temperature regimes which can be explained by the mechanism of transport of the charge carriers of MWNT intervened by that of the polymer matrix. In conclusion how the individual properties of conducting polymer and carbon nanotubes contribute to the unique electronic and conformational properties in their nanocomposites is framed in this investigation. Chapter 5: Magnetic properties of the pristine MWNTs as well as metal nanowires of nickel, nickel-iron (NiFe), nickel-iron-cobalt (NiFeCo) encapsulated in the MWNTs are studied using superconducting quantum interference device (SQUID) magnetometer. A typical example of Ni nanowires encapsulated in MWNT (Ni-MWNT) is taken and the results are compared to other forms of nickel (bulk, nanorod cluster, nanowire) to see the effect of size, shape and environment on the magnetic kproperties. The saturation magnetization and coercivity for Ni-MWNTs are 1.0 emu/gm and 230 Oe. The temperature dependence of magnetization indicates superparamagnetic which is supported by the field-cooled and zero-field-cooled plots determining a blocking temperature ~ 300 K. These altered magnetic properties of Ni-MWNTs are mainly due to the contribution from carbon nanotube encapsulation. Both the shape and environment enhance the total magnetic anisotropy of encapsulated nanowires at least by a factor of four. The encapsulation of metal nanowires in MWNTs tunes the magnetic properties of the system widely, e.g. from diamagnetic (pristine MWNTs) to paramagnetic (Ni-MWNT) to ferromagnetic (NiFe-MWNT) and a combination of para and ferro (NiFeCo-MWNT). Chapter 6: The conclusions of the different works presented in the thesis are coherently summarized in this chapter. Thoughts for future directions are also summed up. Appendix A: Spin dynamics in conducting polymer PEDOT-PSS in its pristine, processed with DMSO and nanocomposite form (with carbon nanotubes) is studied using solid state nuclear magnetic resonance (NMR). Plots of proton spin lattice relaxation times vs. temperature at a fixed frequency 23.4 MHz are compared to study the effect of the external agents on the polymer dynamics.

This diploma thesis deals with the optimization of microclimate of an industrial building. There is required constant temperature with minimal fluctuations during manufacturing process in the building. Due to insufficient cooling power of air-conditioning system was objective to design a solution that ensures stability of internal temperature during production especially in summer and simultaneously should be the solution economically acceptable. Simulation shows original state defined problems. Some new or unusual materials for solar shading are reviewed in the thesis by the experimental measurements and by the comparative method. To each material is assigned shading coefficient according to Czech standards, thereby is achieved universality for calculations of heat gains resulting from solar radiation. By one part of the experiments and their evaluation is determined thickness of the standard single glass glazing. It is also determined proportional transmittance of solar radiation for certain multiwall polycarbonates, which are currently used as fillers of industrial skylights and production hall‘s window openings. From experiments resulting design is subjected to the simulation. Comparison of temperatures is shown for the time before the installation of designed solar shading and after the installation of the solar shading.

In recent years, increased use of electronic devices and wireless operations resulted in unavoidable electromagnetic (EM) pollution which has a significant impact on civil and military sectors. Considering the foremost requirement, huge efforts were invested in the development of electromagnetic interference (EMI) shielding materials. In this context, metals are usually preferred but design complexities like high density and susceptibility towards corrosion are limiting factors; additionally, the reflection of microwaves from the surface fails to serve as EM absorbers. The concern here is to minimize the reflection of the high frequency electromagnetic wave from the surface and to enhance the microwave absorption in GHz frequencies. In this thesis, we have made an attempt to design EMI shielding materials with exceptional absorption ability derived from Polycarbonate (PC)/ Poly styrene-co-acrylonitrile (SAN) based polymer blends. Herein, unique co-continuous micro-phase separated blend structures with selective localization of microwave active nanoparticles in one of the phases were realized to be most effective for microwave attenuation over just dispersing it in one polymer matrix (i.e. PC and SAN composites). The synergistic attenuation of electric and magnetic field associated with EM radiation was achieved through incorporation of various magnetic nanoparticles, however, dispersion of magnetic nanoparticles was a challenging task. Therefore, in order to localize magnetic nanoparticles in PC phase of the blends and to enhance the dispersion state, various modification strategies have been designed. In summary, we have developed a library of engineered nanoparticles to achieve synergistic attenuation of EM radiation mostly through absorption. For instance, the PC/SAN blends containing MWNTs and rGO-Fe3O4 nanoparticles manifested in exceptional EMI shielding, well above required shielding effectiveness value for most of the commercial applications, essentially through absorption. Taken together, the finding suggests that immiscible blends containing MWNTs and the decoration of magnetic nanoparticles (rGO-Fe3O4) on the surface of reduced graphene oxide sheets can be utilized to engineer high-performance EMI shielding materials with exceptional absorption ability.

The search and research for high performance materials for aerospace applications is a continuous evolving process. Among several fibre reinforced polymers, carbon fibre reinforced polymer (CFRP) is well known for its high specific stiffness and strength. Though high modulus and high strength carbon fibre with structural resin systems have currently been established reasonably well and are catering to a wide variety of aerospace structural applications, these properties are generally directional with very high properties along the fibre direction dominated by fibres and low in other directions depending mainly on the resin properties. Thus, there is a need to enhance the mechanical properties of the resin systems for better load transfer and to improve the resin dominated properties like shear strength and properties in directions other than along the fibre. Use of carbon nanotubes (CNTs) with their extraordinary specific stiffness and strength apparently has great potential as an additional reinforcement in resin for development of CNT-CFRP nanocomposites. However, there are several issues that need to be addressed such as compatibility of a particular resin with CNTs, amount of CNTs that can be added, uniform dispersion of these nanotubes, surface treatment and curing process etc., for optimal enhancement of the required properties. Epoxy and cyanate ester resin systems are finding applications in aerospace structures owing to their desirable set of properties. Of these, bisphenol E cyanate ester (BECy) resin of low viscosity with its low moisture absorption, better dimensional stability, and superior mechanical properties can establish itself as potential structural resin system for these applications. BECy in particular has the advantage of being more suitable for out of autoclave manufacturing process such as Vacuum Assisted Resin Transfer Molding (VARTM). Literature shows that, significant work has been carried out by various researchers reporting improvements using CNTs in epoxy resins along with various associated problems. However, studies on effects of addition of CNTs /fCNTs to BECy-CFRP composite system are not well reported. Thus, objective of this work is to study the effects of adding pristine and functionalized CNTs to low viscosity cyanate ester as well as epoxy resin systems. Further, to study the effects on mechanical properties of nanocomposites with carbon fibre reinforcement in these CNT dispersed resin system through a combination of experimental and computational approaches. Multiwall carbon nanotubes (CNTs) without and with different chemical functionalization are chosen to be added to epoxy and BECy resins. The quantity of these CNTs /fCNTs is varied in steps up to 1% by weight. Different methods of mixing such as shear mixing, ultrasonication and combined mixing cycles are implemented to achieve uniform dispersion of these nanotubes in the resin system. Standard test samples are prepared from these mixtures of nanotubes in resin systems to study the variation in mechanical properties. Further, these nanotubes added resin systems are used in fabricating CFRP laminates by VARTM process. Both uni-directional and bi-directional laminates are made with the above modified resin systems with CNTs/fCNTs. Series of experimental investigations are carried out to study various aspects involved in making of nanocomposites and the effects of the same on different mechanical properties of the nanocomposites. Standard specimens are cut out from these laminates to evaluate them for tension, compression, flexure, shear and interlaminar shear strength. The main parameters investigated are the effects of varied quantity of CNTs and functionalized CNTs in the resin mix and in CFRP nanocomposites, effect of different mixing / curing cycles etc. on the mechanical properties of the nanocomposites. The investigations have yielded very interesting and encouraging results to arrive at optimum quantity of CNTs to be added and also the effects of functionalization to achieve enhanced mechanical properties. In addition, correlation of mechanical property enhancements with failure mechanisms, dispersion behaviour and participation of CNTs / fCNTs in load transfer are explained with the aid of scanning electron microscope images. Computational studies are carried out through atomistic models using computational tools to estimate the mechanical properties, understand and validate the effects of various parameters studied through series of experimental investigations. An atomistic model is built taking into consideration the nanoscale effects of the single wall carbon nanotubes (SWCNTs) and its reinforcement in the BECy resin. Using these atomistic models, mechanical properties of individual SWCNT, BECy polymer resin, polymer with different quantities of added SWCNT, and the CFRP laminates with improved resin are computed. As the interaction of CNT with the polymer is only at the outermost layer and the mechanical properties of either MWCNTs or SWCNTs are too high compared to resin systems, it is not expected to have any difference in the final outcome whether it is MWCNT or SWCNT. Hence, only SWCNTs are considered in computational studies as it helps in reducing the complexity of atomistic models and computational time when coupled with polymer resin. This is valid even for functionalized CNT as functionalization is also a surface phenomenon. To start with, the mechanical behaviour of SWCNT is studied using molecular mechanics approach. Molecular mechanics based finite element analysis is adopted to evaluate the mechanical properties of armchair, zigzag and chiral SWCNT of different diameters. Three different types of atomic bonds, i.e., carbon-carbon covalent bond and two types of carbon-carbon van der Waals bonds are considered in the carbon nanotube system. The stiffness values of these bonds are calculated using the molecular potentials, namely Morse potential function and Lennard-Jones interaction potential function respectively and these stiffness values are assigned to spring elements in the finite element model of the SWCNT. The importance of inclusion of Lennard-Jones interactions is highlighted in this study. Effect of these non-bonded interactions is studied by making the numerical stiffness of these bonds to negligible levels and found that they significantly reduce the mechanical properties. The effect of non-bonded Lennard-Jones atomic interactions (van der Waal interactions) considered here is a novelty in this work which has not been considered in previous research works. The finite element model of the SWCNT is constructed, appropriate boundary conditions are applied and the behaviour of mechanical properties of SWCNT is studied. It is found that the longitudinal tensile strength and maximum tensile strain of armchair SWCNTs is greater than that of zigzag and chiral SWCNTs and its value increases with increasing SWCNT diameter. The estimated values of the mechanical properties obtained agree well with the published literature data determined using other techniques. As the systems become more complicated with the inclusion of polymers, molecular dynamics (MD) method using well established codes is more adoptable to study the effect of SWCNTs on BECy. Hence, it is used to model and solve the nanosystems to generate their stress-strain behavior. Further, MD approach followed here can effectively include interfacial interaction between polymer and the CNTs as well. Mechanical properties of SWCNT functionalized SWCNT (fSWCNT), pure BECy resin and that of the CNT nanocomposite consisting of specific quantity of SWCNT / fSWCNT in BECy are estimated using MD method. Atomistic models of SWCNT, fSWCNT, BECy, BECy with specific quantities of CNT / fSWCNT are constructed. A monomer of BECy is modelled and stabilized before its usage as a building block for modelling of BECy resin and to compute its properties. A cell of specific size containing monomers of BECy and another cell of same size with SWCNT at centre surrounded by BECy monomer molecules are built. The appropriate quantity of SWCNT in resin is modelled. This model captures the required density of the composite resin. The models so constructed are subjected to geometric optimization satisfying the convergence criteria and equilibrated through molecular dynamics to obtain a stable structure. The minimized structure is subjected to small strain in different directions to calculate the Young’s modulus and other moduli of the CNT-BECy resin composite. The process is repeated for different quantities of SWCNT in BECy resin to obtain their moduli. Further, tensile and shear strengths of CNT-BECy are obtained by subjecting the equilibrated structure to a series of applied strains from 0 to 10% in steps of 1%. The stress values corresponding to each strain are obtained and a stress – strain curve is plotted. From the stress- strain curve, the strengths of the CNT -BECy which is the stress corresponding to the modulus after which the material starts to soften are determined. Effects of functionalization on mechanical properties of SWCNT are observed. Further, effects of functionalization of SWCNT are studied with a specific quantity of fSWCNT on different moduli and strengths of BECy are investigated. The properties of enhanced CNT–BECy nanocomposite resin with different quantities of added CNT obtained through MD are used to estimate the mechanical properties of the CNT-BECy-CFRP nanocomposite using micromechanics model. Further, validation with experimental results is attempted comparing the trends in enhancement of properties of the CNT-BECy resin and CNT-BECy-CFRP nanocomposite system. The outcome of this research work has been significantly positive in terms of i) Development of an appropriate process establishing different parameters for dispersing CNTs in the resin system, mixing, curing cycle for making of nanocomposites demonstrating significant and consistent enhancement of mechanical properties of BECy based resin system and CFRP nanocomposites using optimum quantity of CNTs /fCNTs through a series of well planned and executed experimental investigations. Evaluation of mechanical properties for each of the cases has been carried out experimentally. ii) Establishing a computational methodology involving intricate atomistic modelling and molecular dynamics of nanosystems for estimation of mechanical properties of BECy polymer resin and to study the effects by addition of SWCNT / functionalized SWCNT on the properties. Results obtained through series of experimental investigations have been validated through this computational study. This could be an important step towards realising the potential of this resin system for high performance aerospace applications. Thus, in brief, detailed experimental work combined with computational studies performed as presented in this thesis resulted in achieving structurally efficient cyanate ester based nanocomposites which is unique and not reported in open literature.

A prototype 3-dimensional (3D) anode, based on multiwall carbon nanotubes (MWCNTs), for Li-ion batteries (LIBs), with potential use in Electric Vehicles (EVs) was investigated. The unique 3D design of the anode allowed much higher areal mass density of MWCNTs as active materials, resulting in more amount of Li+ ion intake, compared to that of a conventional 2D counterpart. Furthermore, 3D amorphous Si/MWCNTs hybrid structure offered enhancement in electrochemical response (specific capacity 549 mAhg-1). Also, an anode stack was fabricated to further increase the areal or volumetric mass density of MWCNTs. An areal mass density of the anode stack 34.9 mg/cm2 was attained, which is 1,342% higher than the value for a single layer 2.6 mg/cm2. Furthermore, the binder-assisted and hot-pressed anode stack yielded the average reversible, stable gravimetric and volumetric specific capacities of 213 mAhg-1 and 265 mAh/cm3, respectively (at 0.5C). Moreover, a large-scale patterned novel flexible 3D MWCNTs-graphene-polyethylene terephthalate (PET) anode structure was prepared. It generated a reversible specific capacity of 153 mAhg-1 at 0.17C and cycling stability of 130 mAhg-1 up to 50 cycles at 1.7C.