This thesis discusses the role of initial particle size on the mechanisms of surface area loss of carbon-supported platinum (Pt) electrocatalysts in the cathode of proton exchange membrane fuel cells. Electrocatalyst decay protocols were used to accelerate cathode performance loss for Pt catalysts. Four cathodes with mean platinum particle sizes of 2.1, 3.5, 6.7 and 11.3 nm were evaluated to elucidate the impact of particle size on initial performance and subsequent degradation, when subjected to identical potential cycles. The degradation of Pt electrochemically active surface area (ECA) was significantly greater for 2.1 and 3.5 nm initial sizes compared to 6.7 and 11.3 nm initial sizes. As expected, the ECA loss of the cathodes shows an inverse proportionality with initial particle size. However, the initial performance of the 11.3 nm initial particle size electrode was significantly lower than the three smaller sizes. Thus, an initial Pt particle size of 6.7 nm was identified to offer the ideal balance performance and durability. The current state of standardization in characterizing particle size by transmission electron microscopy (TEM) is also investigated. The result is a standardized protocol for image acquisition and analysis. / text

Metal nanoparticles have received much interest for their application in catalysis due to high surface-to-volume ratios resulting in more available active sites. Ideally these catalysts are heterogeneous and allow for facile separation from the catalytic reaction mixture making them ideal for industrial application. Dispersed metal nanoparticles are explored due to their high reactivity in solution and are stabilized by surfactants and polymers. However, it is difficult to determine whether or not a catalyst is truly heterogeneous as a certain degree of leaching from the metal nanoparticle is inevitable. Determining the mechanisms involved in nanocatalysis is also a challenge. In this study, a series of dispersed palladium nanocatalysts in the Suzuki reaction with phenylboronic acid and bromobenzene were characterized before and after catalysis to determine what changes occur. Samples where characterized before and after the catalytic reaction by XPS, SEM, and EDS to monitor changes in particle size and composition. Reaction mixtures after catalysis were analyzed by ICP-MS for leached palladium species to determine if concentrations were high enough for homogeneous catalysis to take place. The dispersed palladium nanoparticles studied experienced growth during the catalytic process and a significant amount of leaching. XPS analysis indicates the presence of aromatic species on the particle surface after the catalytic reaction. The aromatic species is likely biphenyl, the product of the catalytic reaction, as the presence of boron and bromine was not found in XPS and EDS analysis.

Nanomateriais baseados em paládio (Pd) desempenham um papel central em catálise. Como suas prorpiedades catalíticas dependem de seus diversos parâmetros físico e químicos, a sua síntese controlada tem grande apelo com contexto do controle e otimização de performances. Nesse trabalho desenvolvemos metodologias simples, versáteis e ambientalmente amigáveis para a preparação de nanoestruturas de Pd com tamanho e forma controlada, seguida pelo seu uso como materiais de partida para a preparação de estruturas bimetálicas contendo ouro (Au) e platina (Pt). Espeficificamente, focamos em nanopartícuals (NPs) de Pd na forma de moitas, prisma e cubo côncavos. Com respeito aos materiais bimetálicos, desenvolvemos estruturas do tipo core-shell, tadpoles, e partículas de Au e Pt decoradas sobre as NPs de Pd. Seguda da síntese, estudamos a performance catalítica dos materiais obtidos frente a hidrogenação do p-nitrofenol (p-NPh) e a oxidação do p-aminotiofenol (PATP) mediada pela ressonância plasmônica de superfície (SPR). Nossos resultados mostraram que as atividades foram dependentes dos parâmetros físicos e químicos que definem as nanoestruturas e que materiais controlados tem desempenho superior ao material comercial. Acreditamos que os resultados desenvolvidos nessa tese contribuem para os mecanismos que governam a síntese controlada de NPs baseadas em Pd, Au e Pt, que pode servir como base para a descoberta de nanomateriais com maior complexidade estrutural e composicional visando aplicações em catálise e plasmônica. / Palladium-based (Pd) nanomaterials play a central role in catalysis. As the catalytic properties of thse materials depend on its various physical and chemical parameters, its controlled synthesis has great appeal in order to control and optimize performances. In this work, we developed facile, versatile and environmentally friendly methodologies for the preparation of Pd nanostructures of controlled sizes and shapes, followed by their use as starting materials for the preparation of bimetallic structures containing gold (Au) and platinum (Pt). Specifically, we focused on Pd nanoparticles (NPs) in the form of bushes, prisms and concave cubes. With respect to bimetallic materials, we have developed core-shell structures, tadpoles, and Au and Pt particles decorated on the Pd NPs. Following their synthestic development, we studied the catalytic performance of the obtained materials towards the hydrogenation of p-nitrophenol (p-NP) and the oxidation of p-aminothiophenol (PATP) mediated by surface plasmon resonance (SPR) excitation. Our results showed that the activities were dependent on the physical and chemical parameters that define the nanostructures and that controlled materials performed better than the commercial conterpart. Overall, we believe that the results developed in this thesis contribute to the mechanisms governing the controlled synthesis of NPs based on Pd, Au and Pt, which can serve as a basis for the discovery of nanomaterials with greater structural and compositional complexity for catalytic and plasmonic applications.

O ouro foi considerado um metal pouco interessante do ponto de vista catalítico por muito tempo, devido ao fato de não quimiossorver moléculas como hidrogênio e oxigênio. Entretanto, suas propriedades catalíticas são reveladas quando suas dimensões são reduzidas a poucos nanômetros, particularmente menores do que 10 nm. Assim, nanocatalisadores de ouro vêm recebendo atenção devido as suas excelentes propriedades catalíticas e alta seletividade em reações de oxidação e redução. O presente trabalho descreve a síntese e caracterização de nanopartículas de ouro suportadas e sua aplicação em reações de oxidação de alcoóis para produção de aldeídos, cetonas e ésteres. Para facilitar a separação do catalisador, um suporte magnético composto de magnetita revestida com sílica foi desenvolvido. A síntese das nanopartículas de ouro suportadas foi realizada de duas maneiras: (I) pela impregnação do suporte com espécies aniônicas de ouro seguido de redução e (II) pela impregnação de nanopartículas de ouro pré-sintetizadas. Em todos os casos nanopartículas de ouro na faixa de 5 nm foram obtidas. A etapa de redução do metal impregnado no suporte foi investigada em detalhe através de duas estratégias: a redução térmica e a redução por hidrogênio. Os testes catalíticos para as reações de oxidação de alcoóis mostraram que os catalisadores sintetizados apresentam altas taxas de conversão e seletividade, porém dependentes do método de preparação utilizado / Gold in the bulk form has been regarded to be an uninteresting metal from the point of view of catalysis, as it is chemically inert towards chemisorption of reactive molecules such as oxygen and hydrogen. However, the catalytic properties of gold are revealed when the size is reduced to few nanometers, particularly with dimension less than 10 nm. Therefore, gold nanocatalysts have received great attention due to the excellent catalytic properties and high selectivity in oxidation and reduction reactions. This master thesis describes the synthesis and characterization of supported gold nanoparticles and their application in alcohol oxidation reaction to produce aldehydes, ketones and esters. In order to improve the catalyst separation and recovery, a magnetic support comprised of magnetite coated by silica was developed. The supported gold nanoparticles were synthesized in two different ways: (I) by impregnation of anionic gold species on silica surface followed by metal reduction, and (II) by impregnation of pre-synthesized gold nanoparticles on the support. In all examples supported gold nanoparticles of about 5 nm were obtained. The reduction step (of the metal impreganted on the support) was investigated in detail by two different strategies: thermal reduction and reduction by hydrogen. The synthesized catalysts showed high conversion rates and selectivity in the catalytic reactions of alcohol oxidation, but those are dependent on the preparation method

O ouro foi considerado um metal pouco interessante do ponto de vista catalítico por muito tempo, devido ao fato de não quimiossorver moléculas como hidrogênio e oxigênio. Entretanto, suas propriedades catalíticas são reveladas quando suas dimensões são reduzidas a poucos nanômetros, particularmente menores do que 10 nm. Assim, nanocatalisadores de ouro vêm recebendo atenção devido as suas excelentes propriedades catalíticas e alta seletividade em reações de oxidação e redução. O presente trabalho descreve a síntese e caracterização de nanopartículas de ouro suportadas e sua aplicação em reações de oxidação de alcoóis para produção de aldeídos, cetonas e ésteres. Para facilitar a separação do catalisador, um suporte magnético composto de magnetita revestida com sílica foi desenvolvido. A síntese das nanopartículas de ouro suportadas foi realizada de duas maneiras: (I) pela impregnação do suporte com espécies aniônicas de ouro seguido de redução e (II) pela impregnação de nanopartículas de ouro pré-sintetizadas. Em todos os casos nanopartículas de ouro na faixa de 5 nm foram obtidas. A etapa de redução do metal impregnado no suporte foi investigada em detalhe através de duas estratégias: a redução térmica e a redução por hidrogênio. Os testes catalíticos para as reações de oxidação de alcoóis mostraram que os catalisadores sintetizados apresentam altas taxas de conversão e seletividade, porém dependentes do método de preparação utilizado / Gold in the bulk form has been regarded to be an uninteresting metal from the point of view of catalysis, as it is chemically inert towards chemisorption of reactive molecules such as oxygen and hydrogen. However, the catalytic properties of gold are revealed when the size is reduced to few nanometers, particularly with dimension less than 10 nm. Therefore, gold nanocatalysts have received great attention due to the excellent catalytic properties and high selectivity in oxidation and reduction reactions. This master thesis describes the synthesis and characterization of supported gold nanoparticles and their application in alcohol oxidation reaction to produce aldehydes, ketones and esters. In order to improve the catalyst separation and recovery, a magnetic support comprised of magnetite coated by silica was developed. The supported gold nanoparticles were synthesized in two different ways: (I) by impregnation of anionic gold species on silica surface followed by metal reduction, and (II) by impregnation of pre-synthesized gold nanoparticles on the support. In all examples supported gold nanoparticles of about 5 nm were obtained. The reduction step (of the metal impreganted on the support) was investigated in detail by two different strategies: thermal reduction and reduction by hydrogen. The synthesized catalysts showed high conversion rates and selectivity in the catalytic reactions of alcohol oxidation, but those are dependent on the preparation method

The feasibility of highly dispersed gold nanocatalyst supported on yttria-stabilized zirconia (YSZ) for the model reactions of C2H4 and CO oxidation is demonstrated for the first time. Gold nanoparticles are synthesized on YSZ powder by chemical reduction of the precursor salt in the mixture of ethanol, water and polyvinylpyrrolidone (PVP). Resulting metal loading of the catalysts are 1 wt.% with average particle sizes ranging from 6 to 9 nm. Results of CO and C2H4 oxidation display catalytic activity at 65 0C and 25 0C for CO and C2H4 oxidation, respectively. The catalytic properties of the catalysts are different due to their average particle size. Electrochemical Promotion of Catalysis (EPOC) of C2H4 oxidation is demonstrated. Application of constant potential difference between two electrodes in the bipolar electrochemical cell led to increase in C2H4 conversion. A proposed mechanism explains the bipolar EPOC phenomenon through formation of O2- flux across the electrochemical cell, resulting in the change of Work Function of gold nanoparticles placed in between the electrodes and is electronically isolated.

The feasibility of highly dispersed gold nanocatalyst supported on yttria-stabilized zirconia (YSZ) for the model reactions of C2H4 and CO oxidation is demonstrated for the first time. Gold nanoparticles are synthesized on YSZ powder by chemical reduction of the precursor salt in the mixture of ethanol, water and polyvinylpyrrolidone (PVP). Resulting metal loading of the catalysts are 1 wt.% with average particle sizes ranging from 6 to 9 nm. Results of CO and C2H4 oxidation display catalytic activity at 65 0C and 25 0C for CO and C2H4 oxidation, respectively. The catalytic properties of the catalysts are different due to their average particle size. Electrochemical Promotion of Catalysis (EPOC) of C2H4 oxidation is demonstrated. Application of constant potential difference between two electrodes in the bipolar electrochemical cell led to increase in C2H4 conversion. A proposed mechanism explains the bipolar EPOC phenomenon through formation of O2- flux across the electrochemical cell, resulting in the change of Work Function of gold nanoparticles placed in between the electrodes and is electronically isolated.

The feasibility of highly dispersed gold nanocatalyst supported on yttria-stabilized zirconia (YSZ) for the model reactions of C2H4 and CO oxidation is demonstrated for the first time. Gold nanoparticles are synthesized on YSZ powder by chemical reduction of the precursor salt in the mixture of ethanol, water and polyvinylpyrrolidone (PVP). Resulting metal loading of the catalysts are 1 wt.% with average particle sizes ranging from 6 to 9 nm. Results of CO and C2H4 oxidation display catalytic activity at 65 0C and 25 0C for CO and C2H4 oxidation, respectively. The catalytic properties of the catalysts are different due to their average particle size. Electrochemical Promotion of Catalysis (EPOC) of C2H4 oxidation is demonstrated. Application of constant potential difference between two electrodes in the bipolar electrochemical cell led to increase in C2H4 conversion. A proposed mechanism explains the bipolar EPOC phenomenon through formation of O2- flux across the electrochemical cell, resulting in the change of Work Function of gold nanoparticles placed in between the electrodes and is electronically isolated.

abstract: With a recent shift to a more environmentally conscious society, low-carbon and non-carbon producing energy production methods are being investigated and applied all over the world. Of these methods, fuel cells show great potential for clean energy production. A fuel cell is an electrochemical energy conversion device which directly converts chemical energy into electrical energy. Proton exchange membrane fuel cells (PEMFCs) are a highly researched energy source for automotive and stationary power applications. In order to produce the power required to meet Department of Energy requirements, platinum (Pt) must be used as a catalyst material in PEMFCs. Platinum, however, is very expensive and extensive research is being conducted to develop ways to reduce the amount of platinum used in PEMFCs. In the current study, three catalyst synthesis techniques were investigated and evaluated on their effectiveness to produce platinum-on copper (Pt@Cu) core-shell nanocatalyst on multi-walled carbon nanotube (MWCNT) support material. These three methods were direct deposition method, two-phase surfactant method, and single-phase surfactant method, in which direct deposition did not use a surfactant for particle size control and the surfactant methods did. The catalyst materials synthesized were evaluated by visual inspection and fuel cell performance. Samples which produced high fuel cell power output were evaluated using transmission electron microscopy (TEM) imaging. After evaluation, it was concluded that the direct deposition technique was effective in synthesizing Pt@Cu core-shell nanocatalyst on MWCNTs support when a rinsing process was used before adding platinum. The peak power density achieved by the rinsed core-shell catalyst was 618 mW.cm-2 , 13 percent greater than that of commercial platinum-carbon (Pt/C) catalyst. Transmission electron microscopy imaging revealed the core-shell catalyst contained Pt shells and platinum-copper alloy cores. Rinsing with deionized (DI) water was shown to be a crucial step in core-shell catalyst deposition as it reduced the number of platinum colloids on the carbon nanotube surface. After evaluation, it was concluded that the two-phase surfactant and single-phase surfactant synthesis methods were not effective at producing core-shell nanocatalyst with the parameters investigated. / Dissertation/Thesis / M.S.Tech Technology 2012

Materials that are light weight, low cost and have high hydrogen storage capacity are essential for on-board vehicular applications. Some reversible complex hydrides are alanates and amides but they have lower capacity than the DOE target (6.0 wt %) for 2010. High capacity, light weight, reversibility and fast kinetics at lower temperature are the primary desirable aspects for any type of hydrogen storage material. Borohydride complexes as hydrogen storage materials have recently attracted great interest. Understanding the above parameters for designing efficient complex borohydride materials requires modeling across different length and time scales. A direct method lattice dynamics approach using ab initio force constants is utilized to calculate the phonon dispersion curves. This allows us to establish stability of the crystal structure at finite temperatures. Density functional theory (DFT) is used to calculate electronic properties and the direct method lattice dynamics is used to calculate the finite temperature thermodynamic properties. These computational simulations are applied to understand the crystal structure, nature of bonding in the complex borohydrides and mechanistic studies on doping to improve the kinetics and reversibility, and to improve the hydrogen dynamics to lower the decomposition temperature. A combined theoretical and experimental approach can better lead us to designing a suitable complex material for hydrogen storage. To understand the structural, bulk properties and the role of dopants and their synergistic effects on the dehydrogenation and/or reversible rehydrogenation characteristics, these complex hydrides are also studied experimentally in this work.