No description available.

Yes / The total energy consumption of many Reverse Osmosis (RO) plants has continuously improved as a result of manufacturing highly impermeable membranes in addition to implementing energy recovery devices. The total energy consumption of the RO process contributes significantly to the total cost of water treatment. Therefore any way of keeping the energy consumption to a minimum is highly desirable but continues to be a real challenge in practice. Potential areas to explore for achieving this include the possibility of optimising the module design parameters and/or the associated operating parameters. This research focuses on this precise aim by evaluating the impact of the design characteristics of membrane length, width, and feed channel height on the total energy consumption for two selected pilot-plant RO process configurations for the removal of chlorophenol from wastewater. The proposed two configurations, with and without an energy recovery device (ERD), consist of four cylindrical pressure vessels connected in series and stuffed with spiral wound membranes. A detailed steady-state model developed earlier by the authors is used here to study such impact via repetitive simulation. The results achieved confirm that the overall energy consumption can be reduced by actually increasing the membrane width with a simultaneous reduction of membrane length at constant membrane area and module volume. Energy savings of more than 60% and 54% have been achieved for the two configurations with and without ERD respectively using process optimization. The energy savings are significantly higher compared to other available similar studies from the literature.

Yes / Reverse Osmosis (RO) process has become one of the most widely utilised technologies for brackish water desalination for its capabilities of producing high-quality water. This paper emphasis on investigating the feasibility of implementing the retentate recycle design on the original design of an industrial medium-sized multistage and multi-pass spiral wound brackish water RO desalination plant (1200 m³/day) of Arab Potash Company (APC) located in Jordan. Specifically, this research explores the impact of recycling the high salinity stream of the 1st pass (at different recycled percentages) to the feed stream on the process performance indicators include, the fresh water salinity, overall recovery rate, and specific energy consumption. The simulation is carried out using an earlier model developed by the same authors for the specified RO plant using gPROMS suits. This confirmed the possibility of increasing the product capacity by around 3% with 100% recycle percentage of the high salinity retentate stream.

Recovering valuable resources from wastewater will transform wastewater management from a treatment focused to sustainability focused strategy, and creates the need for new technology development. An innovative treatment concept - osmotic bioelectrochemical system (OsBES), which is based on cooperation between bioelectrochemical systems (BES) and forward osmosis (FO), has been introduced and studied in the past few years. An OsBES can accomplish simultaneous treatment of wastewater and recovery of resources such as nutrient, energy, and water (NEW). The cooperation can be accomplished in either an internal (osmotic microbial fuel cells, OsMFC) or external (microbial electrolysis cell-forward osmosis system, MEC-FO) configuration. In OsMFC, higher current generation than regular microbial fuel cell (MFC) was observed, resulting from the lower resistance of FO membrane. The electricity generation in OsMFC could greatly inhibit the reverse salt flux. Besides, ammonium removal was successfully demonstrated in OsMFC, making OsMFCs a promising technology for "NEW recovery" (NEW: nutrient, energy and water). For the external configuration of OsBES, an MEC-FO system was developed. The MEC produced an ammonium bicarbonate draw solute via recovering ammonia from synthetic organic solution, which was then applied in the FO for extracting water from the MEC anode effluent. The system has been advanced with treating landfill leachate. A mathematical model developed for ammonia removal/recovery in BES quantitatively confirmed that the NH4+ ions serve as effective proton shuttles across cation exchange membrane (CEM). / Ph. D.

High performance engineering materials, poly(arylene ether)s, having very good mechanical properties, excellent oxidative and hydrolytic stability are promising candidates for alternative materials used in the field of Proton Exchange Membrane Fuel Cells (PEMFCs) and Reverse Osmosis (RO) applications. In particular, wholly aromatic sulfonated poly(arylene ether sulfone)s are of considerable interest in the field of PEMFCs and RO, due to their affordability, high Tg, and the ease of sulfonation. Proton exchange membrane fuels cells (PEMFCs) are one of the primary alternate source of energy. A Proton exchange membrane (PEM) is one of the key component in a PEMFC and it needs to have good proton conductivity under partially humidified conditions. One of the strategies to increase proton conductivity under partially RH conditions is to synthesize hydrophobic-hydrophilic multiblock copolymers with high Ion exchange capacity (IEC) values to ensure sufficient ion channel size. In this thesis two multiblock systems were synthesized incorporating trisulfonated hydrophilic oligomers and were characterized in the first two chapters of the thesis. The first multiblock system incorporated a non-fluorinated biphenol-based hydrophobic block. The second study was focused on synthesizing a fluorinated benzonitrile-based hydrophobic block. A fluorinated monomer was incorporated with the aim to improve phase separation which might lead to increased performance under partially humidified conditions. The third study featured synthesis and characterization of a novel hydroquinone-based random copolymer system precursor, which after post-sulfonation, shall form mono-sulfonated polysulfone materials with potential applications in reverse osmosis. The ratio of the amount of hydroquinone incorporated in the copolymer were varied during the synthesis of the precursor to facilitate control over the post-sulfonation process. The simple and low cost process of post-sulfonating the random copolymer enables the precursor to be a promising material to be used in the reverse osmosis application. / Master of Science

The performance of a poly(ether/urea) membrane has been evaluated in a full scale reverse osmosis system. A series of experiments were conducted with six aromatic compounds - anthracene, pyrene, fluorene, 2-chlorobiphenyl, 2,4,6 trichlorophenol, and pentachlorophenol- and four volatile compounds - trichloromethane, bromodichloromethane, dibromochloromethane, and trichloroethene - as single and multi-solute contaminants. The objectives of the experiments were to determine if poly(ether/urea) membranes could produce a permeate that met maximum contaminant levels (MCL) set by the Safe Drinking Water Act (SDWA) and to correlate membrane performance with physical/chemical properties of the solute contaminants. Aromatic contaminants were removed to concentrations below the current MCLs. However, volatile contaminants were not sufficiently rejected by the membrane to meet either the MCL for total trihalomethanes or trichloroethene. Sorption onto the poly(ether/urea) was found to occur for several of the aromatic compounds tested in this research. This prevented developing any relationship between membrane performance and physical/chemical properties of the solute. / Master of Science

Yes / The performance of a batch reverse osmosis (RO) desalination process in terms of permeate quantity and salinity as a function of feed pressure and feed salinity is evaluated by using laboratory experiments and process modelling. Special attention is paid to the water and salt permeability constants (Kw, Ks) which affect the permeate and salt flux across the membrane. Kw and Ks are found to be strongly pressure-dependent for the batch system which is in-line with earlier observations for continuous RO systems. However, the most important findings of this work are the dependence of Kw and Ks on feed salinity, something that have never been observed or reported in the literature. In order to better qualify these observations, further experiments with the batch system are conducted with a constant feed salinity so that the operating condition resembles that of a continuous RO process.

Yes / Reverse osmosis process is used in many industrial applications ranging from solute-solvent to solvent-solvent and gaseous separation. A number of theoretical models have been developed to describe the separation and fluxes of solvent and solute in such processes. This paper looks into the scope and limitations of two main models (the irreversible thermodynamics and the solution diffusion models) used in the past by several researchers for solute-solvent feed separation. Despite the investigation of other complex models, the simple concepts of these models accelerate the feasibility of the implementation of reverse osmosis for different types of systems and variety of industries. Briefly, an extensive review of these mathematical models is conducted by collecting more than 70 examples from literature in this study. In addition, this review has covered the improvement of such models to make them compatible with multi-component systems with consideration of concentration polarization and solvent-solute-membrane interaction.

Yes / The use of Reverse Osmosis (RO) process in seawater desalination to provide high-quality drinking water is progressively increased compared to thermal technologies. In this paper, multistage spiral wound RO desalination process is considered. Each stage consists of several pressure vessels (PVs) organised in parallel with membrane modules in each PV being organised in series. This allows disconnecting a set of PVs and membrane modules depending on the requirement of cleaning and maintenance. While this flexibility offers the opportunity of generating several RO configurations, we presented only four such configurations of the RO system and analysed them via simulation and optimisation. Production of different grades of water catering different needs of a city is also considered for each of these configurations. The optimisation has resulted in the optimal operating conditions, which maximises the water productivity and minimises the specific energy consumption of the proposed configurations for a given water grade in terms of salinity. For instance, the results indicate that the proposed RO networks can produce drinking water of 500 ppm salinity with a minimum specific energy consumption of 3.755 kWh/m3. The strategy offers the production of different grades of water without plant shutdown while maintaining the membrane modules throughout the year.

Yes / The reverse osmosis (RO) process is one of the most popular membrane technologies for the generation of freshwater from seawater and brackish water resources. An industrial scale RO desalination consumes a considerable amount of energy due to the exergy destruction in several units of the process. To mitigate these limitations, several colleagues focused on delivering feasible options to resolve these issues. Most importantly, the intention was to specify the most units responsible for dissipating energy. However, in the literature, no research has been done on the analysis of exergy losses and thermodynamic limitations of the RO system of the Arab Potash Company (APC). Specifically, the RO system of the APC is designed as a medium-sized, multistage, multi pass spiral wound brackish water RO desalination plant with a capacity of 1200 m3/day. Therefore, this paper intends to fill this gap and critically investigate the distribution of exergy destruction by incorporating both physical and chemical exergies of several units and compartments of the RO system. To carry out this study, a sub-model of exergy analysis was collected from the open literature and embedded into the original RO model developed by the authors of this study. The simulation results explored the most sections that cause the highest energy destruction. Specifically, it is confirmed that the major exergy destruction happens in the product stream with 95.8% of the total exergy input. However, the lowest exergy destruction happens in the mixing location of permeate of the first pass of RO desalination system with 62.28% of the total exergy input.