Livestock wastewater contains a large amount of nutrients that are available for recovery. In this study, a proof of concept process based on forward osmosis (FO) was proposed and investigated for in-situ formation of struvite from digested swine wastewater. This FO system took advantage of a drawback reverse solute flux (RSF) and used the reversed-fluxed Mg^{2+} for struvite precipitation, thereby accomplishing recovery of both water and nutrient. With 0.5 M MgCl2 as a draw solution, high purity struvite formed spontaneously in the feed solution and the water flux through the FO membrane reached 3.12 LMH. The precipitated struvite was characterized and exhibited a similar composition to that of commercial struvite. The FO system achieve >50% water recovery, >99% phosphate recovery (given sufficient magnesium supply), and >93% ammonium nitrogen removal from the digested swine wastewater. The recovered products (both struvite and water) could potentially generate a value of 1.35 $ m^{-3}. The results of this study have demonstrated the feasibility of nutrient recovery from livestock wastewater facilitated by FO treatment. / Master of Science / Forward Osmosis (FO) effectively separates water from dissolved solutes with a semi-permeable membrane. This separation feature can be used in real water body to recover nutrients, concentrate wastewater for further treatment and produce energy for power plant. And the water body rich in nutrients induces the plants growth. These plants consume tons of oxygen in the water which decrease biodiversity in the water body, cause new species invasion and economical lose. The nutrients-rich water has caused trouble to our human being for decades, and one of them is livestock wastewater. Specifically, in this study, the piggery wastewater was used to be treated by FO system. FO has not been used to treat piggery waste/wastewater without additive from previous literature review. In this study, a FO reactor was built up for in-situ nutrient recovery as struvite, which is a valuable slow-release fertilizer. The experiments from this study proved the concept for in-situ struvite recovery from digested livestock wastewater via FO treatment with simultaneous water recovery, and will encourage further exploration of FO promoted resource recovery form wastes.

Yes / Reverse Osmosis (RO) process has become one of the most widely utilised technologies for brackish water desalination for its capabilities of producing high-quality water. This paper emphasis on investigating the feasibility of implementing the retentate recycle design on the original design of an industrial medium-sized multistage and multi-pass spiral wound brackish water RO desalination plant (1200 m³/day) of Arab Potash Company (APC) located in Jordan. Specifically, this research explores the impact of recycling the high salinity stream of the 1st pass (at different recycled percentages) to the feed stream on the process performance indicators include, the fresh water salinity, overall recovery rate, and specific energy consumption. The simulation is carried out using an earlier model developed by the same authors for the specified RO plant using gPROMS suits. This confirmed the possibility of increasing the product capacity by around 3% with 100% recycle percentage of the high salinity retentate stream.

Yes / Reverse osmosis process is used in many industrial applications ranging from solute-solvent to solvent-solvent and gaseous separation. A number of theoretical models have been developed to describe the separation and fluxes of solvent and solute in such processes. This paper looks into the scope and limitations of two main models (the irreversible thermodynamics and the solution diffusion models) used in the past by several researchers for solute-solvent feed separation. Despite the investigation of other complex models, the simple concepts of these models accelerate the feasibility of the implementation of reverse osmosis for different types of systems and variety of industries. Briefly, an extensive review of these mathematical models is conducted by collecting more than 70 examples from literature in this study. In addition, this review has covered the improvement of such models to make them compatible with multi-component systems with consideration of concentration polarization and solvent-solute-membrane interaction.

Yes / The total energy consumption of many Reverse Osmosis (RO) plants has continuously improved as a result of manufacturing highly impermeable membranes in addition to implementing energy recovery devices. The total energy consumption of the RO process contributes significantly to the total cost of water treatment. Therefore any way of keeping the energy consumption to a minimum is highly desirable but continues to be a real challenge in practice. Potential areas to explore for achieving this include the possibility of optimising the module design parameters and/or the associated operating parameters. This research focuses on this precise aim by evaluating the impact of the design characteristics of membrane length, width, and feed channel height on the total energy consumption for two selected pilot-plant RO process configurations for the removal of chlorophenol from wastewater. The proposed two configurations, with and without an energy recovery device (ERD), consist of four cylindrical pressure vessels connected in series and stuffed with spiral wound membranes. A detailed steady-state model developed earlier by the authors is used here to study such impact via repetitive simulation. The results achieved confirm that the overall energy consumption can be reduced by actually increasing the membrane width with a simultaneous reduction of membrane length at constant membrane area and module volume. Energy savings of more than 60% and 54% have been achieved for the two configurations with and without ERD respectively using process optimization. The energy savings are significantly higher compared to other available similar studies from the literature.

Thesis (MEng) -- Stellenbosch University, 2014. / ENGLISH ABSTRACT: When desalinating brackish water by reverse osmosis (RO) or other techniques, high overall water recoveries are essential to minimize brine production and the associated disposal costs thereof. As the overall water recovery increases, concentrations of sparingly soluble salts (e.g. barium sulphate, calcium sulphate) reach levels above saturation, especially near the membrane surface, drastically increasing the scaling propensity. Antiscalants are typically dosed into the feed water to prevent such scaling during RO desalination. However, the carry-over of antiscalant into the concentrate stream can complicate subsequent salt precipitation processes that may be used to increase overall water recovery. These precipitation techniques are sometimes used to reduce the levels of super-saturation in the RO concentrate prior to a subsequent RO desalination step. The purpose of this study was to assess the feasibility of reducing calcium sulphate scaling on RO membranes, by using periodic permeate flushing when feeding a lab-scale RO unit with a supersaturated calcium sulphate solution in the absence of anti-scalant. The overall water recovery was increased by recycling the concentrate, after an intermediate de-supersaturation step. This simulated a multiple-stage RO system, typical of processes used in high-recovery acid mine drainage (AMD) treatment plants. De-supersaturation of the concentrate intermediate was achieved with direct seeded gypsum precipitation, in the absence of any antiscalant. On the membrane surface inside the membrane unit, calcium sulphate concentrations greatly exceeded saturation levels – a combined consequence of the normal concentration process and the well-known surface-based concentration polarisation phenomenon. Therefore, periodic forward-flushing of the supersaturated solution from the membrane unit was performed with permeate. In theory, the periodic flushing removes the highly concentrated layer at the membrane surface during every flush, before scaling can occur. Various flushing regimes were evaluated to assess the effectiveness of the process. A lab-scale desalination unit with a 0.106 m2 flat sheet polyamide RO membrane was designed and constructed. The unit could operate at a feed rate of 12-14 L/h and at permeate fluxes of 12-24 LMH. Super-saturated feed solutions were prepared by mixing sodium sulphate and calcium chloride dihydrate salts with demineralised water, with an initial salinity of ± 5300 mg/L TDS, corresponding to a gypsum saturation index (SIg) of 1.2 for most experiments. The total production time, net permeate production and flux decline were used to compare the flushing efficiency in different experimental runs. Initial tests showed that scaling could be prevented (when operating the unit in full recycle mode, i.e. where both concentrate and permeate were recycled to feed), at flushing frequencies between 12 and 2.4 h-1, when the membrane feed and concentrate were slightly under-saturated (SIg = 0.9) and slightly super-saturated (SIg = 1.1) respectively. However, when switching the same system to non-flushing mode after 24 hours of operation, membrane scaling occurred within 2-3 hours, as indicated by a strong decline in flux. However, when operating the system in concentrate recycle mode (i.e. permeate is withdrawn) with super-saturated feed solutions (e.g. SIg = 1.2), and thus a notably more super-saturated solution in the membrane concentrate, scaling could not be prevented (albeit delayed for some time) with intermittent permeate flushing. A fractional 25-1 factorial design was used to determine which factors had the most significant effect on total production time and permeate production rate, testing five factors: 1) flushing frequency, 2) flushing volume, 3) permeate soak time, 4) permeate flux and 5) instantaneous recovery. The ANOVA analysis showed that total production times were, not surprisingly, primarily affected by the permeate flux, where operation at 24 LMH resulted in a lower net permeate production between 3.0 - 4.2 L, compared to 7.6 - 9.7 L at 12 LMH. Higher permeate fluxes clearly resulted in higher levels of concentration polarisation at the membrane surface, thus increasing the propensity for membrane scaling. Flushing frequency and instantaneous recovery also affected the net permeate production, where 6 h-1 and 10 % were the optimal values respectively within the range of test conditions. The lowest permeate production rate resulted in the highest net permeate volume production (i.e. also longest total production time), confirmed by a least squares regression. In summary: This study showed that periodic permeate flushing could delay the membrane scaling process. However, it failed to prevent membrane scaling completely when operating the system with supersaturated calcium sulphate solutions in the absence of antiscalants. The flushing technique effectively delayed the onset of precipitation, but scaling eventually occurred if the lab-scale RO system was operated in concentrate recycle mode with oversaturated feed solutions (SIg = 1.2). Additional experiments at different cross-flow velocities during permeate flushing, while using an optimised RO test cell flow channel design, are recommended for future studies. / AFRIKAANSE OPSOMMING: Gedurende die ontsouting van brakwater deur tegnieke soos tru-osmose (TO), is ʼn maksimum herwinning van water noodsaaklik om die produksie, en die gepaardgaande kostes van verwydering, van die sout/brak neweproduk te minimeer. Soos die herwinning van water verhoog, so ook verhoog die konsentrasie van moeilik-oplosbare soute (soos bariumsulfaat, kalsiumsulfaat) in die sout konsentraat stroom, totdat die soute uiteindelik superversadiging bereik. Hierdie superversadiging gebeur veral naby die membraanoppervlak, waar dit lei tot ʼn verhoogde kans van presipitasie en skaalvorming. Om dit te voorkom word die voerwater na ʼn TO stelsel tipies gedoseer met antiskaalmiddels. Hierdie antiskaalmiddels verlaat die stelsel saam met die konsentraat, waar hulle gevolglike die presipitasie van soute bemoeilik. Presipitasie van soute uit die konsentraat kan tipies gebruik word om die vlak van superversadiging in die konsentraat te verlaag, waarna verdere TO behandeling gebruik word om selfs ʼn hoër algehele waterherwinning te bewerkstellig. Die doel van hierdie studie was om die vatbaarheid van die vermindering van kalsiumsulfaat (gips) skaalvorming in die afwesigheid van antiskaalmiddels op TO membrane te toets. Dit is bewerkstellig deur ʼn laboratoriumskaal TO eenheid te voer met ʼn superversadigde kalsiumsulfaat oplossing en die membraan periodies met skoon produkwater (permeaat) te was. Die algehele waterherwinning is verhoog deur met ʼn tussenstap die versadigingsvlak van gips in die konsentraat te verlaag, waarna dit hersirkuleer is na die voertenk. Sodoende is ʼn multi-stadium TO stelsel nageboots, soos dit tipies in hoë herwinningsaanlegte, soos met die herwinning van suur mynwater (E: acid mine drainage, AMD), gebruik word. ʼn Verlaging in superversadiging van die konsentraat in die tussenstap is behaal deur die konsentraat direk aan gipskristalle bloot te stel om presipitasie te bewerkstellig in die afwesigheid van enige antiskaalmiddels. Gedurende eksperimente het die soutkonsentrasie op die membraanoppervlak in die TO eenheid superversadigingsvlakke vêr oorskry, as gevolg van die natuurlike konsentrasie proses en die bekende konsentrasie polarisasie oppervlaksverskynsel. Om hierdie superversadiging teen te werk is periodiese saamstroom spoeling van die membraan met skoon produkwater uitgevoer. In teorie het die periodiese spoeling die hoogs gekonsentreerde oplossing van die membraan oppervlak verwyder voor skaalvorming kan plaasvind. Verskillende spoelpatrone is ondersoek om die doeltreffendheid van die spoeling te bepaal. Om die eksperimente uit te voer is ʼn laboratoriumskaal ontsoutingsaanleg met ʼn maklik verwyderbare 0.106 m2 plat-vel poli-amied TO membraan ontwerp en gebou. Die aanleg kan vloeistof voertempo’s tussen 12-24 L/h hanteer en skoon produkwater teen 12-24 LHM lewer. Die superversadigde voer oplossings, soos gebruik in die meerderheid van die eksperimentes is voorberei deur natriumsulfaat en kalsiumchloried-dihidraat soute te meng in gedemineraliseerde water, tot ʼn soutgehalte van ± 5300 mg/L TDS bereik is. Hierdie soutgehalte stem ooreen met ʼn gips versadigingsindeks (E: gypsum saturation index, SIg) van 1.2. Die skoon produkwater totale produksietyd en netto produksie, asook die membraan vloed afname, is gebruik as veranderlikes om die spoel doeltreffendheid tussen eksperimentele lopies te vergelyk. Aanvanklike toetse het getoon dat skalering voorkom is by effens onderversadigde (SIg = 0.9) en effens superversadigde (SIg = 1.1) voer oplossings met die onderskeie spoel frekwensies van 12 en 2.4 h-1, (terwyl die aanleg in algehele hersirkulasie bedryf is, m.a.w. wanneer beide die konsentraat en produkwater gedurig na die voertenk hersirkuleer word). ʼn Effens-superversadigde eksperiment is ook sonder spoeling uitgevoer vir 24 uur. In hierdie geval het skaalvorming binne twee tot drie uur gebeur, soos bevestig deur ʼn skerp afname in die membraan vloed. Skaalvorming kon nie verhoed word terwyl die aanleg bedryf word met superversadigde (SIg = 1.2) voeroplossings en slegs konsentraat hersirkulasie nie (m.a.w. skoon produkwater word opgevang), alhoewel skaalvorming vertraag kon word. Hierdie operasie het tot beduidend meer gekonsentreerde oplossings in die membraan gelei. Om te bepaal watter faktore die grootste invloed op totale produksietyd en netto produksie van skoon produkwater het, is ʼn fraksionele faktoriaalontwerp van 25-1 uitgelê wat vyf faktore toets, naamlik: 1) spoel frekwensie, 2) spoel volume, 3) skoon produkwater weektyd, 4) membraanvloed en 5) oombliklike herwinning. ʼn AVOVA analise het getoon dat totale produksietyd hoofsaaklik deur membraanvloed beïnvloed is, soos verwag kan word. Dit word gestaaf deurdat die aanleg, bedryf teen 24 LMH, slegs 3 - 4.2 L netto produkwater gelewer het, teenoor 7.6 - 9.7 L by 12 LMH. Hoër membraan vloedtempo’s het tot hoër vlakke van konsentrasie polarisasie op die membraanoppervlak gelei, wat ʼn groter neiging tot skaalvorming tot gevolg gehad het. Spoelfrekwensie en oombliklike herwinning het ʼn invloed op die netto produksie van skoon produkwater gehad, met 6 h-1 en 10 % as die onderskeie optimale waardes. ʼn Kleinstekwadraat regressie het aangedui dat die laagste produksietempo van skoon produkwater die hoogste netto produksie van skoon produkwater gelewer het, (asook die langste produksietyd). In opsomming: Hierdie studie het getoon dat gereelde spoeling met skoon produkwater die membraan skaalproses kan vertraag. Gedurende bedryf met superversadigde kalsiumsulfaat oplossings sonder enige antiskaalmiddels is daar gevind dat skaalvorming nie geheel en al vermy kon word nie. Die spoeltegniek, soos gebruik in hierdie studie, het die aanvang van skaalvorming in die laboratorium skaal TO eenheid vertraag, maar bedryf met konsentraat hersirkulasie en superversadigde oplossings (SIg = 1.2) het steeds skaal gevorm. Bykomende eksperimente teen verskeie kruisvloei snelhede gedurende die spoel stap word aanbeveel vir toekomstige studies.

M. Tech., (Chemical Engineering, Department of Chemical Engineering, Faculty of Engineering and Technology Vaal University of Technology| / The methods used to remove potassium sulphate (K2S04) and other impurities contained within Karbochem finishing plant effluent were investigated. Reverse osmosis was explored for this application. The study was conducted in two steps. The first step focuses mainly on the effluent treatment using BW30 flatsheet as well as BW30-2540 spiral-wound reverse osmosis membranes for the rejection of potassium and sulphate ions. The membranes were supplied by Filmtec. The second step reveals the possible use of potassium sulphate obtained from the brine stream in the fertiliser and fertigation industry by a literature search. Reverse osmosis study was conducted on a laboratory scale unit using flat sheet membranes and also on a pilot plant scale using spiral wound membrane modules. The tests were conducted at a feed pressure of 20 bar(g) with the membrane rejections being 98% and 99.1% on flat sheet membrane, and 96.9% and 99.4% on spiral wound membrane for potassium and sulphates respectively. The results show that both membranes have completely desalinated. Significant reduction in the concentrations of all problematic quality parameters, especially of potassium and the sulphate ions was noted. Granular activated carbon (GAC) bed treatment was recommended for pretreatment of the effluent prior to exposure of the membrane to avoid organic fouling of the membrane. GAC treatment was tested to illustrate its effectiveness to adsorb the COD's. / NRF

No / The water permeability constant, (K-w), is one of the many important parameters that affect optimal design and operation of RO processes. In model based studies, e.g. within the RO process model, estimation of W-w is therefore important There are only two available literature correlations for calculating the dynamic K-w values. However, each of them is only applicable for a given membrane type, given feed salinity over a certain operating pressure range. In this work, we develop a time dependent neural network (NN) based correlation to predict K-w in RO desalination processes under fouling conditions. It is found that the NN based correlation can predict the K-w values very closely to those obtained by the existing correlations for the same membrane type, operating pressure range and feed salinity. However, the novel feature of this correlation is that it is able to predict K-w values for any of the two membrane types and for any operating pressure and any feed salinity within a wide range. In addition, for the first time the effect of feed salinity on Kw values at low pressure operation is reported. Whilst developing the correlation, the effect of numbers of hidden layers and neurons in each layer and the transfer functions is also investigated. (C) 2014 Elsevier B.V. All rights reserved.

Fresh water resources in many of the world's oil producing regions, such as western Texas, are scarce, while produced water from oil wells is plentiful, though unfit for most applications due to high salinity and other contamination. Disposing of this water is a great expense to oil producers. This research seeks to advance a technology developed to treat produced water by reverse osmosis and other means to render it suitable for agricultural or industrial use, while simultaneously reducing disposal costs. Pilot testing of the process thus far has demonstrated the technology's capability to produce good-quality water, but process optimization and control were yet to be fully addressed and are focuses of this work. Also, the use of renewable resources (wind and solar) are analyzed as potential power sources for the process, and an overview of reverse osmosis membrane fouling is presented. A computer model of the process was created using a dynamic simulator, Aspen Dynamics, to determine energy consumption of various process design alternatives, and to test control strategies. By preserving the mechanical energy of the concentrate stream of the reverse osmosis membrane, process energy requirements can be reduced several fold from that of the current configuration. Process control schemes utilizing basic feedback control methods with proportional-integral (PI) controllers are proposed, with the feasibility of the strategy for the most complex process design verified by successful dynamic simulation. A macro-driven spreadsheet was created to allow for quick and easy cost comparisons of renewable energy sources in a variety of locations. Using this tool, wind and solar costs were compared for cities in regions throughout Texas. The renewable energy resource showing the greatest potential was wind power, with the analysis showing that in windy regions such as the Texas Panhandle, wind-generated power costs are approximately equal to those generated with diesel fuel.

Thesis (MTech (Chemical Engineering))--Cape Peninsula University of Technology, 2012. / Recently much research and development has been done into the creation of desalination systems in South Africa, with particular emphasis on the commercialisation of desalination plants that serve local communities. This has been successful - there are currently plants running at Bitlerfontien, Bushmans River Mouth and Robben Island - although membrane fouling and scaling remains a problem associated with membrane desalination, as it does worldwide The aim of this study was to Investigate the performance of different type of antiscalants on artificially scaled membranes which we prepared inside the lab as well as on scaled membranes which were used in pilot plant. We used two type of anti-sealants in our research: Vitec 3000 and Zinc ions. The effects of these anti-sealants on the membrane were determind and the RO performances of the treated and untreated membrane compared. A suitable autopsy procedure was established and was then used to autopsy the XLE 4040 membranes. The autopsied membranes were characterized by scanning electron microscopy (SEM) and optical microscopy (OM). The SEM and OM results clearly showed that scaling had taken place: deposits were observed for both the shell and core samples, which were not present in the images of the untreated membrane, especially when looking at high SEM images magnification. Results also showed that the anti-sealants reduced the fouling and scaling on the membrane surface. As a result, the membrane rejection improved. Rejection and flux results indicated that commercial anti-sealant was more effective in preventing scaling than the Zinc ions. For Vitec anti-sealant case, the flux was in steady state at 36.8 Imh (5% less) after 5 hours compared to around 35 Imh (8% less) for zinc ions case. In addition; SEM images showed that less deposited particles are formed when the membrane was treated with commercial anti-sealant.

M. Tech. (Biotechnology, Department of Biosciences, Faculty of Applied and Computer Sciences), Vaal University of Technology. / Reverse osmosis (RO) membranes are widely used in water purification. The presence of biofilms in water and industrial water purification systems is prevalent. As a result, biofouling which is a biofilm problem causes adverse effects on reverse osmosis process, which include flux decline, shorter membrane lifetime and an increase in energy consumption The effect of biofouling on RO membranes was investigated at a water treatment facility at Sasol, Sasolburg by investigating the quality of water purified by the RO system and the extent of fouling that is attributed to biofouling. Chemical and microbiological data was averaged based on the results obtained from water analysis and samples from a fouled membrane. Bacteriological plate counts ranged between log 1.5 to 4 cfu/ml in water samples and log 3.9 to 4.5 cfu/cm2 on biofilm from the membrane surface. Water analysis indicated a high conductivity of 121 µS/cm in the feed and 81 ppm of the TDS, whereas in the permeate conductivity was found to be around 6 µS/cm and 3.8 ppm of the TDS. This indicated that components present in the feed were retained by the membrane. This was supported by membrane autopsy which showed that the bacteria and elements found in the feedwater were also present on the membrane surface, hence contributing to fouling. An average of 33% of cellular ATP was measured on the biofilm from membrane sample, showing that the fouling bacteria are metabolically active in situ. The results clearly indicated that an important biological activity occurred at the membrane surface.