A low power implementation of a CMOS frequency synthesizer at 12 GHz is an important step to improve the efficiency of a wireless transceiver in this frequency band. Since synthesizers are often employed as reference frequency sources such as local oscillators for up or down-conversion in communications system, their design is especially important for high performance transceiver applications. CMOS PLLs operating at high frequencies consume large amounts of power for proper operation, making power efficiency a top priority in transciever implementation. In response, this thesis presents a low power phase and frequency detector with True Single Phase Clocking by employing the .18μ TSMC process with a 1.8 V supply voltage. A conventional but extremely power efficient nano-watt charge pump is also implemented for additional power savings. Furthermore, a state of the art 16/17 prescaler using Current Mode Logic (CML) D-Flip Flops, CMOS inverters, and transmission gates has been optimized for maximum power savings. The prescaler consists of a 4/5 synchronous core and a feedback loop which modulates the 4/5 core to produce a division ratio of 16/17. Instead of employing power hungry CML, the feedback circuit takes advantage of low power NOR and AND gates realized in Transmission Gate Logic (TGL) to reduce the power consumption. To the best of my knowledge, this technique has never been used in a high frequency prescaler before.

A low power implementation of a CMOS frequency synthesizer at 12 GHz is an important step to improve the efficiency of a wireless transceiver in this frequency band. Since synthesizers are often employed as reference frequency sources such as local oscillators for up or down-conversion in communications system, their design is especially important for high performance transceiver applications. CMOS PLLs operating at high frequencies consume large amounts of power for proper operation, making power efficiency a top priority in transciever implementation. In response, this thesis presents a low power phase and frequency detector with True Single Phase Clocking by employing the .18μ TSMC process with a 1.8 V supply voltage. A conventional but extremely power efficient nano-watt charge pump is also implemented for additional power savings. Furthermore, a state of the art 16/17 prescaler using Current Mode Logic (CML) D-Flip Flops, CMOS inverters, and transmission gates has been optimized for maximum power savings. The prescaler consists of a 4/5 synchronous core and a feedback loop which modulates the 4/5 core to produce a division ratio of 16/17. Instead of employing power hungry CML, the feedback circuit takes advantage of low power NOR and AND gates realized in Transmission Gate Logic (TGL) to reduce the power consumption. To the best of my knowledge, this technique has never been used in a high frequency prescaler before.

This thesis presents the CMOS integer-N frequency synthesizer for 5 GHz WCDMA applications with 1.8V power supply. The frequency synthesizer is fabricated in a TSMC 0.18£gm CMOS 1P6M technology process. The frequency synthesizer consists of a phase-frequency detector, a charge pump, a low-pass loop filter, a voltage control oscillator, an auto-band selection, and a pulse-swallow divider. In pulse-swallow divider, this thesis use true single phase clock DFF proposed by Yuan and Svensson to work on high frequency region and to save the circuit area and power. This thesis also proposes an auto-band selection circuit to control the output frequency more precise and easier, and it can also reduce the frequency drift effect caused by technology process or temperature variation.

No description available.

First, a frequency synthesizer for IEEE 802.15.4 / ZigBee transceiver applications that employs dynamic True Single Phase Clocking (TSPC) circuits in its frequency dividers is presented and through the analysis and measurement results of this synthesizer, the need for low power circuit techniques in frequency dividers is discussed. Next, Differential Cascode Voltage-Switch-Logic (DCVSL) based delay cells are explored for implementing radio-frequency (RF) frequency dividers of low power frequency synthesizers. DCVSL ip- ops offer small input and clock capacitance which makes the power consumption of these circuits and their driving stages, very low. We perform a delay analysis of DCVSL circuits and propose a closed-form delay model that predicts the speed of DCVSL circuits with 8 percent worst case accuracy. The proposed delay model also demonstrates that DCVSL circuits suffer from a large low-to-high propagation delay ( PLH) which limits their speed and results in asymmetrical output waveforms. Our proposed enhanced DCVSL, which we call DCVSL-R, solves this delay bottleneck, reducing PLH and achieving faster operation. We implement two ring-oscillator-based voltage controlled oscillators (VCOs) in 0.13 mu m technology with DCVSL and DCVSL-R delay cells. In measurements, for the same oscillation frequency (2.4GHz) and same phase noise (-113dBc/Hz at 10MHz), DCVSL-R VCO consumes 30 percent less power than the DCVSL VCO. We also use the proposed DCVSL-R circuit to implement the 2.4GHz dual-modulus prescaler of a low power frequency synthesizer in 0.18 mu m technology. In measurements, the synthesizer exhibits -135dBc/Hz phase noise at 10MHz offset and 58 mu m settling time with 8.3mW power consumption, only 1.07mWof which is consumed by the dual modulus prescaler and the buffer that drives it. When compared to other dual modulus prescalers with similar division ratios and operating frequencies in literature, DCVSL-R dual modulus prescaler demonstrates the lowest power consumption. An all digital phase locked loop (ADPLL) that operates for a wide range of frequencies to serve as a multi-protocol compatible PLL for microprocessor and serial link applications, is presented. The proposed ADPLL is truly digital and is implemented in a standard complementary metal-oxide-semiconductor (CMOS) technology without any analog/RF or non-scalable components. It addresses the challenges that come along with continuous wide range of operation such as stability and phase frequency detection for a large frequency error range. A proposed multi-bit bidirectional smart shifter serves as the digitally controlled oscillator (DCO) control and tunes the DCO frequency by turning on/off inverter units in a large row/column matrix that constitute the ring oscillator. The smart shifter block is completely digital, consisting of standard cell logic gates, and is capable of tracking the row/column unit availability of the DCO and shifting multiple bits per single update cycle. This enables fast frequency acquisition times without necessitating dual loop fi lter or gear shifting mechanisms. The proposed ADPLL loop architecture does not employ costly, cumbersome DACs or binary to thermometer converters and minimizes loop filter and DCO control complexity. The wide range ADPLL is implemented in 90nm digital CMOS technology and has a 9-bit TDC, the output of which is processed by a 10-bit digital loop filter and a 5-bit smart shifter. In measurements, the synthesizer achieves 2.5GHz-7.3GHz operation while consuming 10mW/GHz power, with an active area of 0.23 mm2.

This diploma thesis concerns with analysis and dividing of frequency synthesizers and design of DDS, PLL synthesizers. Base types of frequency synthesizers are described including differences between methods of their operation. Base circuits of both – DDS and PLL synthesizers and other important circuits are described in details at design part of this thesis. Design of DDS and PLL synthesizer is described in particular sections. Both synthesizers are directly realized and stand-alone control applications are created. PLL synthesizer is also ready to control thru Agilent VEE program environment. Particular example application is designed in Agilent VEE. This application is used as basis of attached lab project.

"2009" / Thesis (MSc (Hons))--Macquarie University, Faculty of Science, Dept. of Physics and Engineering, 2010. / Bibliography: p. 163-166. / Introduction -- Design theory and process technology -- 15GHz oscillator implementations -- 24GHz oscillator implementation -- Frequency prescaler implementation -- MMIC fabrication and measurement -- Conclusion. / Advances in Silicon Germanium (SiGe) Bipolar Complementary Metal Oxide Semiconductor (BiCMOS) technology has caused a recent revolution in low-cost Monolithic Microwave Integrated Circuit (MMIC) design. -- This thesis presents the design, fabrication and measurement of four MMICs for frequency synthesis, manufactured in a commercially available IBM 0.18μm SiGe BiCMOS technology with ft = 60GHz. The high speed and low-cost features of SiGe Heterojunction Bipolar Transistors (HBTs) were exploited to successfully develop two single-ended injection-lockable 15GHz Voltage Controlled Oscillators (VCOs) for application in an active Ka-Band antenna beam-forming network, and a 24GHz differential cross-coupled VCO and 1/6 synchronous static frequency prescaler for emerging Ultra Wideband (UWB) automotive Short Range Radar (SRR) applications. -- On-wafer measurement techniques were used to precisely characterise the performance of each circuit and compare against expected simulation results and state-of-the-art performance reported in the literature. -- The original contributions of this thesis include the application of negative resistance theory to single-ended and differential SiGe VCO design at 15-24GHz, consideration of manufacturing process variation on 24GHz VCO and prescaler performance, implementation of a fully static multi-stage synchronous divider topology at 24GHz and the use of differential on-wafer measurement techniques. -- Finally, this thesis has llustrated the excellent practicability of SiGe BiCMOS technology in the engineering of high performance, low-cost MMICs for frequency synthesis in millimeterwave (mm-wave) devices. / Mode of access: World Wide Web. / xxii, 166 p. : ill (some col.)

Low noise low division 2 GHz RF synthesizer integrated circuits (ICs) are conventionally implemented in some form of HBT process such as SiGe or GaAs. The research in this dissertation differs from convention, with the aim of implementing a synthesizer IC in a more convenient, low-cost Si-based CMOS process. A collection of techniques to push towards the noise and frequency limits of CMOS processes, and possibly other IC processes, is then one of the research outcomes. In a synthesizer low N-divider ratios are important, as high division ratios would amplify in-band phase noise. The design methods deployed as part of this research achieve low division ratios (4 ≤ N ≤ 33) and a high phase comparison frequency (>100 MHz). The synthesizer IC employs a first-order fractional-N topology to achieve increased frequency tuning resolution. The primary N-divider was implemented utilising current mode logic (CML) and the fractional accumulator utilising conventional CMOS. Both a conventional CMOS phase frequency detector (PFD) and a CML PFD were implemented for benchmarking purposes. A custom-built 4.4 GHz synthesizer circuit employing the IC was used to validate the research. In the 4.4 GHz synthesizer circuit, the prototype IC achieved a measured in-band phase noise plateau of L( f ) = -113 dBc/Hz at a 100 kHz frequency offset, which equates to a figure of merit (FOM) of -225 dBc/Hz. The FOM compares well with existing, but expensive, SiGe and GaAs HBT processes. Total IC power dissipation was 710 mW, which is considerably less than commercially available GaAs designs. The complete synthesizer IC was implemented in Austriamicrosystems‟ (AMS) 0.35 μm CMOS process and occupies an area of 3.15 x 2.18 mm2. / Dissertation (MEng)--University of Pretoria, 2010. / Electrical, Electronic and Computer Engineering / unrestricted