The NASA GSFC/Wallops Flight Facility focused radar system employed a large (43 cm diameter) dielectric focusing lens such that the water surface (target) was illuminated by a small radar spot (~1.25 cm diameter). With this small spot size, surface profiles and probability density functions could be generated. The system suffered an interference problem which made reliable data collection impossible. Study showed that the system had to be operated bistatically in order to reduce the effects of interference found to be caused by signal leaking directly from the transmitter to the receiver. Since the system was operated in a confined space (the wind-wavetank), multipath was found to generate interference signals. The multipath interference was reduced via strategic placement of radio frequency absorber. A comparison was made between experimental results with the original system and the final bistatic system to demonstrate the effect of the reduction in interference. A model was also derived for the direct leakage interference and used to explain experimental results. / Master of Science

Thesis (MScEng (Electrical and Electronic Engineering))--University of Stellenbosch, 2003. / No abstract available

Thesis (PhD)--Stellenbosch University, 1993 / ENGLISH ABSTRACT: An extensive literature study revealed numerous Jauman absorber examples with reasonable absorption properties. Unfortunately, tractable and detailed design techniques were found to be scarce, and often only applicable to absorbers with two or three layers. The research described in this report was therefore aimed at, and culminated in, general design methods for multilayered electric screen J auman absorbers. As a starting point, the synthesis problem is formulated by idealizing the spacers (assumed lossless and commensurate) and resistive sheets (assumed to have zero thickness), and by considering the absorption of a normally incident plane wave. An equivalent circuit model is derived, using the analogy between plane waves in stratified media, and guided waves in TEM transmission lines. The network is analyzed using Richard's frequency surrogate, S = tanh(s = cr +jw), and concise equations and algorithms are presented for symbolic and numerical analysis. Maximum bandwidth synthesis of the classic one-layer absorber, or Salisbury screen, proved to be simple, clearly illustrates the analytic approach, and apparently has not been published before. The two-layer absorber was also found to be algebraically simple enough to be synthesized in closed form, is dealt with comprehensively, and the treatment consolidates and formalizes many of the design techniques available in the literature. Networks comprising commensurate transmission lines and conductances have been investigated by Richardsl , but unfortunately the topology-driven realizability constraints on the input impedance of the Jauman network is only dealt with briefly. Fruitless investigations by the author showed this to be a formidable problem, and as a result the research concentrated on tractable and iterative synthesis algorithms for multilayered absorbers, instead of formal filter synthesis techniques. These algorithms may be summarized as follows: • A key concept in the multilayer zero-placement synthesis methods that will be presented, is the ability to physically realize a given set of reflection coefficientzeros. This involves solving a set of highly non-linear equations, and a gradientmethod iterative algorithm has been developed to achieve this . • The first application of the aforementioned algorithm is to synthesize all reflection zeros at S →∞, thereby obtaining a maximally flat reflection coefficient magnitude response. Stable and rapid convergence was found for up to at least 20 layers, thereby extending the two- and three-layer algebraic solutions available in the literature. It was found that a stringent restriction exists on the maximum dielectric constant (Er) of the spacers, thereby limiting the practical implementation of these solutions . • Through judicious manipulation of reflection zeros at distinct physical frequencies, an equiripple absorption response may be obtained. An elegant algorithm is presented to facilitate this, and it was found that these solutions represent substantial improvements over examples available in the literature. Restrictions still apply to the spacer Er, but these are more relaxed and practical equiripple absorbers are possible. In addition, the spread in sheet resistivities is much smaller than in comparable maximally flat solutions. • Numerical searches indicated that the aforementioned equiripple responses are very close to, but not absolutely optimal, in the sense of maximum bandwidth. The small bandwidth and/or absorption improvements that were found were almost negligible from a practical viewpoint, but the optimal synthesis problem is academically very important. Through use of the general Chebyshev approximation method, an algorithm is developed which finds the local optimal response in the vicinity of such a parent equiripple solution. Although it might be tempting to classify the algorithm as a brute force method, it will be shown that this is not the case, and that its solutions provide the answer to the fundamental and unsolved optimal design problem. These algorithms have been implemented, and tables of resistive sheet values are presented for N up to 8, a range of Er values corresponding to low loss foams, and for various absorption levels. / AFRIKAANSE OPSOMMING: geen opsomming

Electrically-small loop antennas are a complex topic, with many design concepts to consider, including: effective magnetic core permeability, antenna impedance, antenna radiation, surrounding medium effects, and optimization approaches. There is a plethora of literature available covering these subjects but many conflict, compete, or are overall lacking; this thesis seeks to compare and analyze literature then validate with measurements, allowing optimal design.

Master of Science / Department of Animal Sciences and Industry / Dale A. Blasi / Effects of corn processing with or without the inclusion of wet corn gluten feed (WCGF) on growth and performance were analyzed in two experiments. Treatments for both experiments were a diet including 47% whole-shelled corn (WSC) with no WCGF (WSC/0WCGF), a diet including 29% WSC with 30% WCGF (WSC/30WCGF), a diet including 47% dry-rolled corn (DRC) with no WCGF (DRC/0WCGF), and a diet with 29% DRC with 30% WCGF (DRC/30WCGF). Exp. 1 used 279 crossbred calves (230 kg) that were allocated to treatments in a 2x2 factorial completely randomized block design. No corn processing effects (all P > 0.31) were observed. Final BW was increased when WCGF was included in the diet (P = 0.03). ADG was increased for diets with WCGF (P = 0.03). Efficiency was not affected by the incorporation of WCGF in the diet. Digestibility of DM (P = 0.006) and starch (P = 0.009) was increased by the dietary inclusion of WCGF. There were no benefits observed for processing corn, but including WCGF at 30% (DM) increased gains and overall performance. Exp. 2 was a digestibility experiment using 5 ruminally cannulated Holstein heifers (248 ± 13 kg BW) in a 4 × 4 Latin square with an additional animal that was administered the same treatment sequence as another heifer on trial. No corn processing effects were observed for DM, starch, and ADF intake (all P ≥ 0.09). Dietary WCGF inclusion increased starch, non-starch and ADF intake (all P ≤ 0.01). Digestibility of DM, starch, non-starch, and ADF was not affected by corn processing, but DM, non-starch, and ADF digestibility were increased by WCGF inclusion in the diet (P ≤ 0.03). Ruminal pH was not affected by corn processing (P = 0.90) or dietary WCGF inclusion (P = 0.09). No corn × WCGF interactions were detected. There also was no difference among VFAs or total VFA concentration (all P ≥ 0.12) for corn processing effects. Passage rate (%/h) and ruminal liquid volume was not affected by corn processing or dietary WCGF inclusion (all P ≥ 0.66).

Coarse particulate organic matter (CPOM) is an essential part of the food chain in aquatic ecosystems because it represents a readily available carbon and energy source. The process by which it decomposes in rivers has been well studied and documented. However, the rate and extent of biodegradability of various CPOM components (i.e., twigs, leaves, grass, etc.) in storm drains is not well understood. The Jordan River TMDL study identified storm water generated CPOM as a likely cause of low dissolved oxygen levels in the lower Jordan River, but recent investigations have suggested that dissolved organic matter generated from this CPOM in storm drains and culverts entering into the Jordan River, rather than the CPOM itself, is the main driver of oxygen impairment. The degradability of CPOM components transported and stored in the storm drain system was studied to understand its relative impact on dissolved oxygen and nutrient status in the Jordan River. Results indicate the generation of highly degradable organic material is a function of the starting CPOM, and oxygen consumption is associated with the dissolved portion of organic material leached from CPOM in water. Leaves and grass produced the highest levels of all parameters studied. Between 93% to 95% of total oxygen demand is generated within the first 1 to 3 hours of the 24 hour test. Chemical oxygen demand and dissolved organic carbon proved to be the best indicator of biochemical oxygen demand. By using the results of the leaching study an estimate of water quality indicator levels in the Jordan River was made, and was compared to levels in samples collected from the Jordan River. The estimate proved accurate for dissolved organic carbon but not for total or volatile suspended solids. Results of this study were used to discuss possible solutions to reduce oxygen demand in the Jordan River.

Background: Material handling is a large part of a company´s internal work and represents between 15 % and 70 % of the total cost of a manufactured product. By improving the internal handling of material, more efficient distribution and manufacturing flows are possible. The material handling process is an input to the production and assembly process that has to be defined and mapped so that it can be improved. The material handling process studied at Volvo CE Braås includes goods receiving, storage, packaging as well as the order/delivery process to assembly, and will finish with the material transport to the assembly line. Research questions: How can the material handling process, from goods receiving to assembly line, at Volvo CE in Braås be described by using VSM? What kinds of waste can be identified? By proposing a future-state map, how can the identified problems and waste be reduced or eliminated? Methodology: This thesis is a descriptive case study and was conducted with a deductive approach. Data was collected by our own observations, personal interviews, statistics, benchmarking and questionnaire. The scientific credibility of this thesis was secured by for example using many sources, avoidance of assumptions, studying a common process and following standardized steps of the VSM tool. Conclusions: The material handling process was described in the separated areas of goods receiving, storage and assembly line. Visualization was given in a current-state map. Five different kinds of waste were identified. Finally, suggestions of improvements were presented along with a future-state map. Suggestions on future research: A more detailed VSM including information flow and lead times could be studied. Scenario simulations of critical areas within the material handling process could be preformed. Furthermore, an ABC classification of articles and storage locations can be done to optimize storage.

The research of this thesis is on the mobile TV antenna designs. There are three antenna designs proposed in this thesis. The first two designs are for portable TV sets. They are different from the traditional straight monopole antenna because the two proposed designs can be built-in with the portable TV set. The third one is for laptop applications. It can be stored inside a laptop when the antenna is not in use, and can be pulled out of the laptop when in operation. Thus the proposed antenna will not affect the appearance of the laptop.

The topic of this thesis presents a digital front end (DFE) of the digital video broadcasting over terrestrial (DVB-T). The DVB-T system is similar to most of the prior digital communication system. It is roughly divided into two major parts, one for channel coding/decoding, and the other for modulation/demodulation. The thesis is mainly focused on the DVB-T digital video broadcasting demodulation part of the receiver and the integration of a complete digital front demodulation system. The major operational processor of the DFE is a 2K/8K dual-mode FFT processor, which has been implemented by the TSMC ( Taiwan Semiconductor Manu-facturing Company ) 0.35um 2P4M CMOS process technology to justify the simulation results as well as the correctness of the proposed architecture.

Three novel wideband antennas suitable for DTV (Digital Television) signal reception in the 470 ~ 806 MHz band for Portable Media Playrer (PMP) applications are presented in this thesis. The antennas include a novel broadband planar monopole antenna in Chpater 2, a novel low-profile planar inverted-U monopole antenna in Chpater 3, and a novel internal planar inverted-F antenna in Chpater 4. These antennas all have wide impedance bandwidths, good radiation efficiencies, and good radiation patterns. In addition, we propose a one-layer simplified hand model for achieving efficient and reliable simulation study for PMP antennas. The studied antenna in Chapter 2 is selected to be the example to study the user¡¦s hand effect on the antenna for PMP application.