A solar fiber optic lighting system, SP3 from the Swedish company Parans Solar Lighting AB, has been installed in a study area/corridor test site. A collector is tracking the sun during daytime, focusing the direct sun irradiance via Fresnel lenses into optical fibers, which guide the solar light into the building. The illumination properties of the system have been characterized. The energy saving due to reduced need of artificial lighting have been calculated and methods for balancing the artificial lights in the test site have been evaluated. The illumination at the test site using solar light was at least as high as when using the artificial lights and even higher at very clear days. The luminous flux output (500 lm) was somewhat lower than specified by the manufacturer (550 lm) at 100 000 lx direct sun illuminance. The output at 130 000 lx was high 767±33 lm the sunlight coupling efficiency 23 %. However, for a 20 m SP3 system the luminous flux output (400 lm) at 100 000 lx was higher than specified (350 lm). The SP3 system of Parans provides high quality solar light. It has a fuller spectrum close to the spectrum of the sun compared to the fluorescent lights at the test site. The correlated color temperature of the system was 5800±300 K and the color rendering index 84.9±0.5. The lighting energy saved due to decreased need for artificial light was estimated to 19 % in Uppsala which has 1790 annual sun hours. The savings in Italy, which has 3400 sun hours, is 46 %. Additional saving, especially in warmer countries can be obtained due to decreased need for cooling in the building as the solar luminaires provide negligible heat to the indoor air. Economical saving could also be realized by improved well-being of the occupants spending time under the solar luminaires. Three ways of balancing the artificial light due to sunshine fluctuations have been investigated. The global horizontal irradiance could not be used as a control signal for balancing the artificial lights but a pyranometer attached to the SP3 sun tracking collector was usable. Also the signal from an indoor luxmeter sensor could be used for balancing the light. However the signal from the light sensor which makes the SP3 collector to track the sun is probably the most cost effective method as it would serve two purposes; tracking the sun and balancing the artificial lights.

För ett genomsnittligt småhus i Sverige idag går ca 5000 kWh till hushållsel. Av dessa 5000 kWh går 7% till att driva diskmaskiner. Effektiviseringen av diskmaskiner har framförallt strävat efter en låg vatten- och energianvändning, en kort processtid samt en effektiv rening av disken. Det finns dock gränser för hur effektiva diskmaskinerna kan göras med traditionell teknik. Därför har producenter under de senaste åren börjat se sig om efter mindre traditionella metoder som till exempel bruket av en värmepump för att få ned energiförbrukningen. Syftet med det här examensarbetet har varit att ta fram systemlösningar för värmepump i diskmaskin samt att utvärdera energibesparingspotentialen i denna tillämpning. Målet har varit att ta fram och beskriva de möjliga systemlösningar som uppstår vid en idégenerering. Att välja ut två lösningar för närmare undersökning, att bestämma en lämplig kompressoreffekt samt att beräkna energibesparingen dessa lösningar ger. En litteraturstudie har gjorts av teknik och tillämpningar inom området, som till exempel värmeväxlaranvändning i diskmaskiner samt användandet av värmepumpar i andra vitvaror. Denna litteraturstudie följdes upp av en idégenerering, som tar hänsyn till möjliga värmekällor och –sänkor. Idégenereringen gav upphov till två systemlösningar som modellerades i MATLABs Simulink för att en lämplig kompressoreffekt och storleken på energibesparingen skulle bestämmas. De två utvalda lösningarna ifrån idégenereringen var utomhusluftlösningen, där värme hämtas från uteluften och energilagerlösningen, där värme hämtas ur ett energilager. I båda lösningarna överförs värmen till det kalla ingående vattnet. Energiåtgången för utomhusluftlösningen var beroende av köldmediets förångningstemperatur och modellering av lösningen visade att energiåtgången var 0,25 kWh vid en förångningstemperatur på -10°C, och 0,18 kWh vid 5°C. Vid modellering av energilagerlösningen påvisades en energiåtgång på 0,23 kWh. Slutsatsen som drogs var att kompressorn vid energilagerlösningen skall leverera en effekt på 240 W till köldmediet. / For an average detached house in Sweden today about 5000 kWh are used for household electricity. Of these 5000 kWh 7% are used to run dishwashers. The streamlining of dishwashers has above all strived for a lower water and energy use, a short process time along with a more efficient cleaning of the dishes. There are however limits for how efficient the dishwashers can be made with traditional technology and acceptable costs. Therefore producers have, during recent years, started looking for less traditional methods, for example the use of a heat pump to reduce the energy use. The purpose of this examination work has been to find system solutions for an application of a heat pump in a dishwasher and to evaluate the possible energy saving for each solution. The goal has been to find and describe possible system solutions, which came up during the idea generation. To choose some of these for a closer investigation, to decide a fitting mechanical power for the compressor and to calculate the energy saving these solutions give rise to. The method has consisted of a literature study, an idea generation, which takes the heat sources and sinks in consideration and a modelling in MATLAB’s Simulink of the selected solutions from the idea generation, which has been used to fit a mechanical power for the compressor. The result of the idea generation was two solutions, an outdoor air solution, which collects heat from the outdoor air and gives it to the cold water which enters the machine and a energy storage solution, which collect heat from a heat stock to give to the cold entering water. A modelling of these show an energy usage of 0,24 respectively 0,17 kWh for the outdoor air solution, with a heat source temperature at 10 °C respectively 5°C and a energy usage of 0,22 kWh for the energy storage solution for one round. The conclusion that was drawn was that the compressor of the energy storage solution should deliver a mechanical power of 240 W to the refrigerant.

Detta examensarbete syftar till att utreda vilka av Svenska kyrkans byggnader i Växjö som ska energideklareras samt utföra en energideklaration av en kontorsbyggnad. I energideklarationen ingår det även att ge åtgärdsförslag för olika energibesparingsmöjligheter. En fördjupad studie i nattkylning av stommen har också utförts. Examensarbetet är uppdelat i tre huvuddelar, indelning av byggnader, utförande av energideklaration samt fördjupad studie av nattkyla. I den första delen delas byggnaderna in i grupper utifrån verksamhet och byggnadstyp och därefter utreds om de ska energideklareras. Målet med denna indelning av byggnader är att Svenska kyrkan ska få vetskap om vilka av deras byggnader som berörs av lagen om energideklarationer. I andra delen görs en energideklaration för en kontorsbyggnad. Det visar sig att det finns en hel del energibesparande åtgärder som kan göras i kontorsbyggnaden. En del av åtgärderna är endast enkla åtgärder som inte kräver något större ingrepp i byggnaden för att utföras. I den tredje delen genomförs en fördjupad studie i nattkylning av stommen i byggnader, där tung och lätt stomme jämförs gentemot varandra. För att utföra jämförelsen används simuleringsprogrammet IDA Klimat och Energi. Resultatet av simuleringen visar ingen besparing av energi till följd av nattkylning av stommen i den simulerade byggnaden, vilket leder fram till en parameterdiskussion om hur olika parametrar påverkar lönsamheten vid nattkyla. / This diploma work aims to investigate which of the Swedish church’s buildings in Växjö that needs to be energy declared and also to perform an energy declaration of an office building. In the energy declaration there’s also included measures for various energy-saving potential. An in-depth study of night-cooling of the framework has also been performed. This diploma work is divided into three main parts, classification of buildings, carrying out the energy declaration and a depth study of night-cooling of the building’s framework. In the first part buildings where divided into different groups on the basis of activities and type of building and then investigated whether to be energy declaration or not. The objective of this classification of buildings is that the Swedish church will know which of their buildings that’s affected by the law concerning energy declarations. The second part is an energy declaration of an office building. It turns out that there are a lot of energy-saving measures that can be done in the office building. Some of them are only simple measures that don’t require any major interference in the building to be performed. In the third part is carried out an in-depth study of night-cooling of buildings’ frameworks, where heavy and light frames are compared against each other. In order to carry out the comparison the simulation program IDA Climate and Energy was used. The results of the simulation shows no saving of energy as a result of night-cooling of the building frame in the simulated building, which leads to a parameter discussion on how various parameters affecting the profitability of night-cooling.

In this thesis, we propose a power saving strategy based on tree splitting algorithm in wireless sensor network with multiple packet reception. We concentrate on the case that maximum queue size is 1. We derive both analytical results and simulation results. We use theory of Markov chain to analyze the evolution of the system state. In addition, we propose to use Renewal theory to calculate the throughput. Furthermore, we obtain the average system size, the packet blocking probability, and the average packet delay. Because the network model is distributed, we can¡¦t understand the state of network all the time. So we use the length of last collision resolution cycle to predict the length of next cycle, and determine the sleeping time by the predicted length of next cycle to implement power saving. At last we will use the simulation result to show the performance of our power saving strategy.

Using 2002-2006 Household Budget Survey, this thesis investigates the income, consumption and saving dynamics of Turkish households within a life-cycle theory framework by employing cross-sectional analyses and cohort techniques. Cohort techniques are used not only to analyze these variables, but also to investigate the demographics and components of income and consumption. The analyses are deepened by dividing the sample according to the location of the households (urban-rural areas), and significant differences are found between urban and rural households, especially in terms of saving behaviors. Income, consumption and savings of formal and informal households are also investigated. Analyzing these households provides information regarding the precautionary saving since the higher income uncertainty of the informal households is expected to force them for extra saving due to precautionary motive. Finally, the life-cycle model and the precautionary saving hypothesis are tested by estimating log-linearized Euler equations. In the test of precautionary saving hypothesis, formal-informal data are used as a proxy for the risk variable. According to the estimation results, the predictions of the life-cycle model do not hold for Turkey but there is no evidence that this is due to precautionary saving.

<p>Detta examensarbete syftar till att utreda vilka av Svenska kyrkans byggnader i Växjö som ska energideklareras samt utföra en energideklaration av en kontorsbyggnad. I energideklarationen ingår det även att ge åtgärdsförslag för olika energibesparingsmöjligheter. En fördjupad studie i nattkylning av stommen har också utförts. Examensarbetet är uppdelat i tre huvuddelar, indelning av byggnader, utförande av energideklaration samt fördjupad studie av nattkyla. I den första delen delas byggnaderna in i grupper utifrån verksamhet och byggnadstyp och därefter utreds om de ska energideklareras. Målet med denna indelning av byggnader är att Svenska kyrkan ska få vetskap om vilka av deras byggnader som berörs av lagen om energideklarationer. I andra delen görs en energideklaration för en kontorsbyggnad. Det visar sig att det finns en hel del energibesparande åtgärder som kan göras i kontorsbyggnaden. En del av åtgärderna är endast enkla åtgärder som inte kräver något större ingrepp i byggnaden för att utföras. I den tredje delen genomförs en fördjupad studie i nattkylning av stommen i byggnader, där tung och lätt stomme jämförs gentemot varandra. För att utföra jämförelsen används simuleringsprogrammet IDA Klimat och Energi. Resultatet av simuleringen visar ingen besparing av energi till följd av nattkylning av stommen i den simulerade byggnaden, vilket leder fram till en parameterdiskussion om hur olika parametrar påverkar lönsamheten vid nattkyla.</p> / <p>This diploma work aims to investigate which of the Swedish church’s buildings in Växjö that needs to be energy declared and also to perform an energy declaration of an office building. In the energy declaration there’s also included measures for various energy-saving potential. An in-depth study of night-cooling of the framework has also been performed. This diploma work is divided into three main parts, classification of buildings, carrying out the energy declaration and a depth study of night-cooling of the building’s framework. In the first part buildings where divided into different groups on the basis of activities and type of building and then investigated whether to be energy declaration or not. The objective of this classification of buildings is that the Swedish church will know which of their buildings that’s affected by the law concerning energy declarations. The second part is an energy declaration of an office building. It turns out that there are a lot of energy-saving measures that can be done in the office building. Some of them are only simple measures that don’t require any major interference in the building to be performed. In the third part is carried out an in-depth study of night-cooling of buildings’ frameworks, where heavy and light frames are compared against each other. In order to carry out the comparison the simulation program IDA Climate and Energy was used. The results of the simulation shows no saving of energy as a result of night-cooling of the building frame in the simulated building, which leads to a parameter discussion on how various parameters affecting the profitability of night-cooling.</p>

Military Forward Operating Base Camps (FOBs) support and enable sustained military operations abroad by providing safe locations for soldiers and supporting contractors to eat, sleep, and maintain personal hygiene. FOBs need some amount of energy and water to provide these services but are often located in austere environments that do not have access to grid utilities. Off-grid FOBs are not self-sufficient; they are dependent on supply chains for the services they provide to camp occupants. The challenge of supplying FOBs with fuel and water and removing waste (resource resupply and waste removal comprise logistical requirements) is associated with very high human, monetary, strategic, and environmental costs. There are many research efforts across the U.S. Department of Defense (DoD) that seek to reduce FOB logistical requirements, but it is currently very difficult to identify the research efforts that are most beneficial to DoD goals. There are also many factors that make designing FOBs to be more self-sufficient challenging including varying missions, environments, and legacy equipment at currently-fielded FOBs, a lack of baseline data on FOB logistical requirements, an unclear relationship between design changes and resource use behavior, and an unclear valuation of saved resources. This research seeks to develop computer tools and contribute to a methodology that can be used to design FOBs that are more self-sufficient. More self-sufficient FOBs provide high quality services to occupants but do so with mitigated logistical requirements. To this end, a detailed computer model of specific type of FOB (a single 150-person Force Provider module) is developed, and baseline levels of resource requirements are established. Potentially resource-saving devices and other design changes are incorporated into the FOB model and simulated to assess each design change's effect on resource use and waste production. Then, estimated resource savings are weighed against required investment for each design change to arrive at design recommendations. The results of this research effort are specific design recommendations for making the Force Provider system more self-sufficient, as well as computer tools and a methodology that are applicable to other off-grid habitation redesign problems. / text

This thesis consists of a summary and four self-contained papers. Paper [I] Following the 1987 report by The World Commission on Environment and Development, the genuine saving has come to play a key role in the context of sustainable development, and the World Bank regularly publishes numbers for genuine saving on a national basis. However, these numbers are typically calculated as if the tax system is non-distortionary. This paper presents an analogue to genuine saving in a second best economy, where the government raises revenue by means of distortionary taxation. We show how the social cost of public debt, which depends on the marginal excess burden, ought to be reflected in the genuine saving. We also illustrate by presenting calculations for Greece, Japan, Portugal, U.K., U.S. and OECD average, showing that the numbers published by the World Bank are likely to be biased and may even give incorrect information as to whether the economy is locally sustainable. Paper [II] This paper examines the relationships among per capita CO2 emissions, per capita GDP and international trade based on panel data spanning the period 1960-2008 for 150 countries. A distinction is also made between OECD and Non-OECD countries to capture the differences of this relationship between developed and developing economies. We apply panel unit root and cointegration tests, and estimate a panel error correction model. The results from the error correction model suggest that there are long-term relationships between the variables for the whole sample and for Non-OECD countries. Finally, Granger causality tests show that there is bi-directional short-term causality between per capita GDP and international trade for the whole sample and between per capita GDP and CO2 emissions for OECD countries. Paper [III] Fundamental questions in economics are why some regions are richer than others, why their growth rates differ, whether their growth rates tend to converge, and what key factors contribute to explain economic growth. This paper deals with the average income growth, net migration, and changes in unemployment rates at the municipal level in Sweden. The aim is to explore in depth the effects of possible underlying determinants with a particular focus on local policy variables. The analysis is based on a three-equation model. Our results show, among other things, that increases in the local public expenditure and income taxe rate have negative effects on subsequent income income growth. In addition, the results show conditional convergence, i.e. that the average income among the municipal residents tends to grow more rapidly in relatively poor local jurisdictions than in initially “richer” jurisdictions, conditional on the other explanatory variables. Paper [IV] This paper explores the relationship between income growth and income inequality using data at the municipal level in Sweden for the period 1992-2007. We estimate a fixed effects panel data growth model, where the within-municipality income inequality is one of the explanatory variables. Different inequality measures (Gini coefficient, top income shares, and measures of inequality in the lower and upper part of the income distribution) are examined. We find a positive and significant relationship between income growth and income inequality measured as the Gini coefficient and top income shares, respectively. In addition, while inequality in the upper part of the income distribution is positively associated with the income growth rate, inequality in the lower part of the income distribution seems to be negatively related to the income growth. Our findings also suggest that increased income inequality enhances growth more in municipalities with a high level of average income than in municipalities with a low level of average income.

published_or_final_version / Business / Master / Master of Philosophy

Energy consumption for heating and ventilation of buildings is still in 2011considered far too high, but there are many ways to save energy and construct lowenergy buildings that have not been fully utilised. This doctoral thesis has focused onone of these - low temperature heating systems. Particular attention has been given tothe ventilation radiator adapted for exhaust-ventilated buildings because of itspotential as a low energy consuming, easily-operated, environmentally-friendlysystem that might also ensure occupant health and well-being. Investigations were based on Computational Fluid Dynamics (CFD) simulations andanalytical calculations, with laboratory experiments used for validation. Main conclusions: Low and very low temperature heating systems, such as floor heating, in general createan indoor climate with low air speeds and low temperature differences in the room, whichis beneficial for thermal comfort. A typical disadvantage, however, was found to beweakness in counteracting cold down-flow from ventilation air supply units in exhaustventilatedbuildings. with ventilation radiators, unlike most other low temperature systems, it was found thatthe risk of cold draught could be reduced while still maintaining a high ventilation rateeven in cold northern European winters. ventilation radiators were found to be more thermally efficient than traditional radiators. design of ventilation radiators could be further modified for improved thermal efficiency. at an outdoor temperature of -15 °C the most efficient models were able to give doublethe heat output of traditional radiators. Also, by substituting the most efficient ventilationradiators for traditional radiators operating at 55 °C supply water temperature, it wasfound that supply water temperature could be reduced to 35 °C while heat outputremained the same and comfort criteria were met. lowering the supply water temperature by 20 °C (as described above) could givecombined energy savings for heating and ventilation of 14-30 % in a system utilising aheat pump. supply water temperatures as low as 35 °C could increase potential for utilising lowtemperature heat sources such as sun-, ground-, water- or waste-heat. This would beparticularly relevant to new-built “green” energy-efficient buildings, but severaladvantages may apply to retrofit applications as well. Successful application of ventilation radiators requires understanding of relevant buildingfactors, and the appropriate number, positioning and size of radiators for best effect.Evaluation studies must be made at the level of the building as a whole, not just for theheating-ventilation system. This work demonstrated that increased use of well-designed ventilation radiatorarrangements can help to meet regulations issued in 2008 by the Swedish Departmentof Housing (Boverket BBR 16) and goals set in the Energy Performance of BuildingsDirective (EPBD) in the same year. / QC 20110328 / STEM Projektnummer:30326-1 Energieffektiva lågtemperatursystem i byggnader