Ce travail vise à comprendre l’évolution de la texture cristallographique et l’anisotropie du comportement mécanique après laminage à chaud et traitements thermiques d’un Al-Cu-Li 2050 et d’un Al-Zn-Mg-Cu 7050, et expliquer leurs différences. La texture est analysée par EBSD et RX après des essais de compression plane à chaud et après des laminages à chaud industriels. L’anisotropie est étudiée sur des tôles fortes industrielles après différents détensionnements et dans différents états microstructuraux par des essais de traction à 0°, 45° et 90° par rapport à DL. Enfin, nous comparons nos mesures à des résultats simulés par des modèles de plasticité cristalline (modèles de Taylor). Il est montré que, déformés dans des conditions identiques, les deux alliages développent les mêmes textures de laminage jusqu'à une déformation de 2.6. La présence de 1% massique de Li n’est à priori pas responsable d’une texture particulière. En revanche la température de laminage, qui est généralement plus élevée pour les Al-Cu-Li que pour les Al-Zn-Mg-Cu, a un impact important aux grandes déformations, notamment en favorisant la composante Laiton {110}<112>. L'anisotropie d'une tôle laminée de 2050 est pour une large part due à la texture cristallographique. Elle augmente quand un détensionnement est effectué par traction dans la direction DL et diminue quand il est effectué à 45°/DL. La précipitation durcissante, composée de T1 Al2CuLi en forme de plaquettes sur les plans {111}Al, augmente la résistance de la direction préalablement tractionnée mais n'est pas responsable dans nos conditions expérimentales d'une forte aggravation de l'anisotropie. Dans le 7050, l'anisotropie diminue entre l’état mûri naturellement et l’état sur-revenu. La précipitation de sur-revenu du 7050 atténue l'effet de la texture cristallographique sur l'anisotropie et rend, en comparaison, le 2050 d’autant plus anisotrope. / This work aims to understand hot rolling texture evolution and anisotropy of mechanical behaviour on an Al-Cu-Li 2050 and an Al-Zn-Mg-Cu 7050, and aims to explain their differences. Crystallographic textures are analysed by EBSD and X-ray after hot plane strain compressions and after industrial hot rolling. Anisotropy of industrial hot rolled plates is investigated after different stretching and different ageing treatments by means of tensile tests at 0°, 45° and 90° to RD. Experimental results are compared to predictions using plasticity models (Taylor models). It is shown that, under the same processing conditions, the two alloys develop the same rolling textures up to strain of 2.6 ; it can be concluded that the presence of 1wt% of Li does not by itself favour a particular texture. However, it is shown that Brass component {110}<112> is favoured by an increasing rolling temperature, which is generally higher in the Al-Cu-Li than in the Al-Zn-Mg-Cu. Anisotropy of hot rolled 2050 is for a large part caused by crystallographic texture. It increases when stretch axis is at 0° and decreases when stretch axis is at 45°. Hardening precipitation, made by plate shape T1 Al2CuLi lying on the {111}Al, increases yield strength in the stretched direction but it is not responsible in our experimental conditions for a high increase of anisotropy. Anisotropy of 7050 is less important in the over aged state than in the natural aged state. Over ageing precipitation of 7050 reduces the effect of crystallographic texture on the anisotropy and makes 2050 appearing much more anisotropic.

This diploma thesis solves possibilities of utilization optical fiber as sensor. At the beginning, basic division of this sensors is desribed, their principles and usage. Then the thesis is focused on distributed sensors based on the interference of the light, interferometers. This optic fiber interferometers are described, mainly their modifications for detection and localization of vibrations along optical fiber. Significant part of the thesis deals with dual Mach--Zehnder interferometer. This interferometer is theoreticaly desribed and simulated in Matlab. Further the thesis deals with development of two aplication in Matlab software. One application is for simulation and theoretical computation of dual Mach--Zehnder interferometer. Second application serves for signal processing of acquired data that are measured on this interferometer. At the end of the thesis, dual Mach--Zehnder interferometer is designed and build in laboratory enviroment and executed measurement and localization of vibrations using this interferometer.

The dissertation thesis deals with signal detection by an ionization detector in the environmental scanning electron microscope and utilization of this detector to gain required information in a specimen image. Main interest is focused on the detector containing several electrodes with a varied geometry arrangement and voltages on these electrodes. The detector was named segmental ionization detector. Detection capabilities of the segmental ionization detector were studied through computer simulations and experiments in the microscope utilizing knowledge from a technical literature background. On the base of the accomplished experiments, the segmental ionization detector has been optimized for the secondary electron detection improvement and at another configuration optimized for a high material contrast acquisition of the specimen image. Consideration of benefits of the examined segmental ionization detectors is included in the work.

科学研究費補助金 研究種目:試験研究 課題番号:63850078 研究代表者:日比野 倫夫 研究期間:1988-1989年度

Thesis deals with environmental scanning electron microscopy and with detection of signal electrons by using ionization detector. First part talks about the principle of environmental scanning electron microscope. Second part describes signals generated by interaction of primary electron beam with sample. Third section explains the principle of impact ionization and ionization detector. Experimental part deals with usage of segmental ionization detector and with measuring of signal amplification from copper and platinum. Thesis also examines arrangement of electrodes of ionisation detector on material contrast and examines also on influence of voltage contrast on base - emitter junction of an NPN bipolar transistor. All experiments were carried out in dependency on saturated water vapour pressure in sample chamber.

In this work, a new method for mass determination of single low-charged particles in the sub-picogram regime is developed. It opens applications to chemical physics and surface science via determination of growth rates. The method combines the well-known electrodynamic quadrupole ion trap in a UHV-chamber and fourier transformation of scattered light. The achieved mass resolution of down to $10^{-4}$ at 100 fg mass on a time scale of ten seconds allows a resolution of a few percent of the mass of an adsorbed monolayer and to determine growth rates down to one molecule per second on a time scale of one day. The observation of temperature dependent sticking coefficients results in the measures of the energy of an adsorption barrier. Observation of discrete steps in the rate gives information about the density of molecules in an ordered layer. Temperature dependent desorption data gives the binding energy. The dependence of these observables on the controllable curvature and charge of the substrate's surface is measurable. The first part of this dissertation consists of a description of the common theory of the quadrupole ion trap with the completion of not widely known, newly introduced, contributions to the trapping potential. These contributions lead to systematic shifts in the mass determination. In particular the influence of the inhomogenity of the electrical field, that is used for compensating the gravitational force, is investigated analytically and corroborated experimentally. It is assumed, that the particle's finite size effects in a further shift. In the experimental part initial demonstrative measurements are presented: the time-resolved adsorption of fullerene, anthracene and NO on silica spheres with 500nm diameter has been measured at room temperature. In addition the secondary electron yield of in-situ prepared particles during irradiation with monoenergetic electrons has been determined by analyzing the distribution of change of the number of elementary charges by single events of charging.

In this work, experimental and theoretical approaches are applied to the study of chemical reaction dynamics. In Chapter 2, two applications of transition state theory are presented: (1) Application of microcanonical transition state theory to determine the rate constant of dissociation of C2F3I after π∗ ← π excitation. It was found that this reaction has a very fast rate constant and thus is a promising system for testing the statistical assumption of molecular reaction dynamics. (2) A general rate constant expression for the reaction of atoms and molecules at surfaces was derived within the statistical framework of flexible transition state theory. In Chapter 4, a computationally efficient TDDFT approach was found to produce useful potential energy surface landscapes for application to non-adiabatic predissociative dynamics of the molecule CS2 after excitation from the ground state to the singlet C-state. In Chapter 5, ultrafast experimental results of excitation of CS2 to the predissociative neutral singlet C-state is presented. The bandwidth of the excitation laser was carefully tuned to span a two-component scattering resonance with each component differently evolving electronically with respect to excited state character during the quasi-bound oscillation. Scalar time-resolved photoelectron spectra (TRPES) and vector time-resolved photoelectron angular distribution (TRPAD) observables were recorded during the predissociation. The TRPES yield of photoelectrons was found to oscillate with a quantum beat pattern for the photoelectrons corresponding to ionization to the vibrationless cation ground state; this beat pattern was obscured for photoelectron energies corresponding to ionization from the vibrationally excited CS2 cation. The TRPAD data was recorded for two general molecular ensemble cases: with and without a pre-excitation alignment laser pulse. It was found that in the case of ensemble alignment (Chapter 6), the “molecular frame” TRPAD (i.e. TRMFPAD) was able to image the purely valence electronic dynamics of the evolving CS2 C-state. The unaligned ensemble TRPAD observable suffers from excessive orientational averaging and was unable to observe the quantum beat. Engineering efforts were also undertaken to eliminate scattered light background signal (Chapter 7, Appendix A) and improve laser stability as a function of ambient pressure (Appendix B) for TRMFPAD experiments. / Thesis (Ph.D, Chemistry) -- Queen's University, 2012-09-11 22:18:20.89

This work deals with the evaluating of the signal level value from the sample in the environmental SEM. In work there were processed the comparison of the osciloscopic method for the evaluating of the signal level value in the environmental SEM, the method for the evaluating of the signal level from the grey level of the sample images and the method for the evaluating of the signal level from the osciloscop. There are described the advantages and disadvantages of the methods and procedures for processing the methods.

Le contrôle de santé structural ou Structural Health Monitoring (SHM) des matériaux constitue une démarche fondamentale pour la maîtrise de la durabilité et de la fiabilité des structures en service. Au-delà des enjeux industriels et humains qui ne cessent de s’accroître en termes de sécurité et de fiabilité, le contrôle de santé doit faire face à des exigences de plus en plus élaborées. Les nouvelles stratégies de contrôle de santé doivent non seulement détecter et identifier l’endommagement mais aussi quantifier les différents phénomènes qui en sont responsables. Pour atteindre cet objectif, il est nécessaire d’accéder à une meilleure connaissance des processus d’endommagement. Par ailleurs, ceux-ci surviennent fréquemment sous l’effet de sollicitations mécaniques et environnementales. Ainsi, il est indispensable, d’une part, d’élaborer des méthodes de traitement des signaux permettant d’estimer les effets des conditions environnementales et opérationnelles, dans un contexte de l’analyse des événements précurseurs des mécanismes d’endommagement, et, d’autre part, de définir les descripteurs d’endommagement les plus adaptés à cette analyse. Cette étude propose donc des méthodes de traitement du signal permettant d’atteindre cet objectif, dans un premier temps, pour l’estimation des effets externes sur les ondes multidiffusées dans un contexte de contrôle de santé actif et, dans un second temps, pour l’extraction d’un indicateur d’endommagement à partir de l’analyse des signaux d’émission acoustique dans un contexte de contrôle de santé passif. Dans la première partie de ce travail, quatre méthodes de traitement du signal sont proposées. Celles-ci permettent de prendre en compte les variations des conditions environnementales dans la structure, qui dans le cadre de cette thèse, se sont limitées au cas particulier du changement de la température. En effet, les variations de température ont pour effet de modifier les propriétés mécaniques du matériau et par conséquent la vitesse de propagation des ondes ultrasonores. Ce phénomène entraîne alors une dilatation temporelle des signaux acoustiques qu’il convient d’estimer afin de suivre les variations de température. Quatre estimateurs de coefficients de dilatation sont alors étudiés : Il s’agit de l’intercorrélation à fenêtre glissante, utilisée comme méthode de référence, la méthode du stretching, l’estimateur à variance minimale et la transformée exponentielle. Les deux premières méthodes ont été déjà validées dans la littérature alors que les deux dernières ont été développées spécifiquement dans le cadre de cette étude. Par la suite, une évaluation statistique de la qualité des estimations est menée grâce à des simulations de Monte-Carlo utilisant des signaux de synthèse. Ces signaux sont basés sur un modèle de signal multidiffusé prenant en compte l’influence de la température. Une estimation sommaire de la complexité algorithmique des méthodes de traitement du signal complète également cette phase d’évaluation. Enfin, la validation expérimentale des méthodes d’estimation est réalisée sur deux types de matériaux : Tout d’abord, dans une plaque d’aluminium, milieu homogène dont les caractéristiques sont connues, puis, dans un second temps dans un milieu fortement hétérogène prenant la forme d’une plaque composite en verre/epoxy. Dans ces expériences, les plaques sont soumises à différentes températures dans un environnement thermique contrôlé. Les estimations de température sont alors confrontées à un modèle analytique décrivant le comportement du matériau. La seconde partie de ce travail concerne la caractérisation in situ des mécanismes d’endommagement par émission acoustique dans des matériaux hétérogènes. Les sources d’émission acoustique génèrent des signaux non stationnaires... / Structural health monitoring (SHM) of materials is a fundamental measure to master thedurability and the reliability of structures in service. Beyond the industrial and human issuesever increasing in terms of safety and reliability, health monitoring must cope with demandsincreasingly sophisticated. New health monitoring strategies must not only detect and identifydamage but also quantify the various phenomena involved in it. To achieve this objective, itis necessary to reach a better understanding of the damage process. Moreover, they frequentlyoccur as a result of mechanical and environmental stresses. Thus, it is essential, first, to developsignal processing methods for estimating the effects of environmental and operational conditions,in the context of the analysis of precursor events of damage mechanisms, and on theother hand, to define the damage descriptors that are the most suitable to this analysis. Thisstudy proposes signal processing methods to achieve this goal. At first, to the estimation ofexternal effects on the scattered waves in an active health control context, in a second step, tothe extraction of a damage indicator from the signals analysis of acoustic emission in a passivehealth monitoring context.In the first part of this work, four signal processing methods are proposed. These allow takinginto account the variation of environmental conditions in the structure, which in this thesis,were limited to the particular case of temperature change. Indeed, temperature changes have theeffect of altering the mechanical properties of the material and therefore the propagation velocityof ultrasonic waves. This phenomenon then causes a dilation of the acoustic signals that shouldbe estimated in order to monitor changes in temperature. Four estimators of dilation coefficientsare then studied: the intercorrelation sliding window, used as reference method, the stretchingmethod, the minimum variance estimator and the exponential transform. The first two methodshave already been validated in the literature while the latter two were developed specificallyin the context of this study. Thereafter, a statistical evaluation of the quality of estimates isconducted through Monte Carlo simulations using synthetic signals. These signals are basedon a scattered signal model taking into account the influence of temperature. A raw estimateof the computational complexity of signal processing methods also completes this evaluationphase. Finally, the experimental validation of estimation methods is performed on two types ofmaterial: First, in an aluminum plate, homogeneous medium whose characteristics are known,then, in a second step in a highly heterogeneous environment in the form of a compositeglass/epoxy plate. In these experiments, the plates are subjected to different temperatures in acontrolled thermal environment. The temperature estimates are then faced with an analyticalmodel describing the material behavior.The second part of this work concerns in situ characterization of damage mechanisms byacoustic emission in heterogeneous materials. Acoustic emission sources generate non-stationarysignals. The Hilbert-Huang transform is thus proposed for the discrimination of signals representativeof four typical sources of acoustic emission in composites: matrix cracking, debondingfiber/matrix, fiber breakage and delamination. A new time-frequency descriptor is then definedfrom the Hilbert-Huang transform and is introduced into an online classification algorithm. Amethod of unsupervised classification, based on the k-means method, is then used to discriminatethe sources of acoustic emission and the data segmentation quality is evaluated. Thesignals are recorded from blank samples, using piezoelectric sensors stuck to the surface of thematerial and sensitive samples (sensors integrated within the material)...

This thesis deals with the topic of sequential and parallel grammars. Both of these groups cover a large number of grammar families, most of which, however, are not widely used because of the difficulties related to their processing. The thesis examines some of these grammar types, such as scattered-context grammars, multigenerative systems, and interactive L-systems, with focus on their normal forms. Subsequently, it introduces a set of algorithms utilising properties of the discussed grammar types as well as their normal forms. These algorithms are based on the Cocke-Younger-Kasami algorithm for context-free grammars, and are capable of parsing any grammar in the corresponding normal form. Finally, a program implementing the proposed algorithms is presented.