Recently, additive manufacturing (AM), or "3D printing," is expanding into civil infrastructure applications, particularly cementitious materials. To ensure the safety, health, and welfare of the public, quality assurance and quality control (QA/QC) methods via standardized testing procedures are of the upmost importance. However, QA/QC methods for these applications have yet to be established. This thesis aims to implement existing ASTM standards to characterize additive manufactured cementitious composites and to gather better information on how to tackle the challenges that are inherent when printing with cementitious materials. In this work, fresh mix properties and hardened concrete properties were investigated using current ASTM standards as a starting point for applying or adapting them for AM applications. Specifically, this project applied existing ASTM standards for fresh mix mortars to measure setting time, flow, and early compressive strength as qualitative indicators of printability, pumpability, and buildability. The fresh mix properties were investigated for 12 different mortar mixes to demonstrate the effect that moisture content, absorption, and sand type can have on these fresh mix properties. The results for setting time and compressive strength demonstrated that there was less variability in the properties when the moisture condition of the aggregate was measured and accounted. Flow was shown to be strongly influenced by the sand type. Additively manufactured mortars were used to print a box in a layer-by-layer process. To evaluate the effect of layering on the flexural strength, three-point bending tests were implemented using four different loading orientations to explore the anisotropic mechanical properties. The observed anisotropic behavior was corroborated with stereo-digital image correlation data showing the stress-strain and load-deflection relationships. Two orientations (A and B) demonstrated brittle behavior while the other two orientations (C and D) experienced quasi-brittle behavior. In addition, setting a minimum unit weight of 132 pcf enabled an analysis of the effect that defects had on the mechanical performance: specimens greater than 132 pcf demonstrated greater and less variable strengths than the specimens less than 132 pcf. The discussion of how defects impacted performance of the different orientations can be valuable when determining how to effectively model, design, and inspect 3D printed structures in the future. The findings of this thesis confirm that existing ASTM standards for mortars can be modified and applied to AM cementitious composites for QA/QC. It is recommended that mixtures used in 3D printing of cementitious composites should design and accommodate the moisture condition of the aggregate to optimize the predictability of the fresh and early-age properties. For the hardened properties, it is recommended that testing procedures such as flexural testing account for anisotropic behavior. Furthermore, for implementation of 3D printed concrete structures, it is highly recommended that design is a function of loading orientation due to the anisotropic properties of the composite. / Master of Science / Recently, additive manufacturing (AM), or "3D printing," is expanding into civil infrastructure applications, specifically cementitious materials such as mortar and concrete. Understanding and predicting the behavior of the materials when using this new technique is vital for quality assurance and quality control (QA/QC). However, standard test methods have yet to be established for this new construction technique. This thesis aims to use existing testing standards to characterize AM cementitious composites and to gather better information on how to tackle the challenges of printing with these materials. In this work, properties before and after the materials hardened were studied by adapting current testing standards. Specifically, this project applied existing testing standards for fresh mix mortars to measure setting time, flow, and early compressive strength. These properties can serve as indicators of specific printing requirements. The fresh mix properties were studied for 12 different mortar mixes to show the effect of moisture content, absorption, and sand type. The results suggest that there was less variability in the properties when the moisture condition and type of the aggregate was accounted. The fresh mix materials were printed in a layer-by-layer process and then hardened in place. The effects of the layers were explored by performing flexure tests using four orientations with respect to how the load was applied to the layers. The observed difference in behavior for the different orientations was supported by digital image correlation data. In addition, an analysis of the effect defects had on the performance was included. Understanding how defects impacted performance can be valuable for effectively designing 3D printed structures in the future. The results of this thesis confirm that existing testing standards for mortars can be adapted and applied to AM cementitious materials for QA/QC. It is recommended that mixtures used in 3D printing of cementitious materials should account for the moisture condition of the aggregate to improve the predictability of the fresh and early-age properties. For the hardened properties, it is recommended that the design is a function of loading orientation due to the difference in behavior for the different orientations of the material.

A literatura atual aponta o exercício físico como uma das estratégias nãofarmacológicas mais utilizadas no tratamento e prevenção de condições que acometem o tecido ósseo. Ademais, estudos indicam que a suplementação de creatina pode exercer efeitos positivos sobre o ganho de massa óssea. Sendo assim, o objetivo deste estudo foi investigar os efeitos preventivos do exercício físico associado à suplementação de creatina na perda de massa óssea em ratas ovariectomizadas. Diante disso, sessenta e cinco ratas da linhagem Wistar foram pareadas pelo peso corporal e dividas aleatoriamente em cinco grupos, sendo eles: 1) ratas falso-operadas (SHAM); 2) ratas ovariectomizadas (OVX), sedentárias e suplementadas com placebo (PL); 3) ratas OVX, sedentárias e suplementadas com creatina (CR); 4) ratas OVX, treinadas e suplementadas com placebo (PL+TR) e 5) ratas OVX, treinadas e suplementadas com creatina (CR+TR). Os animais foram submetidos a um protocolo de treinamento físico em declive em esteira rolante e suplementados com creatina diariamente por meio de gavagem esofágica. Foi realizada a avaliação de densitometria óssea para a obtenção dos parâmetros ósseos de conteúdo mineral ósseo (CMO) e densidade mineral óssea (DMO) de corpo total e regional, assim como a composição corporal nos períodos pré e pósintervenção. Além disso, foi removido o fêmur direito para a análise biomecânica. Após a intervenção, o grupo PL+TR apresentou maiores valores de CMO e DMO em comparação ao grupo PL (p=0,004 e p=0,020, respectivamente), ao passo que o grupo CR+TR experimentou maiores incrementos para o CMO e tendência ao aumento da DMO em comparação ao grupo CR (p=0,011 e p=0,064). A análise biomecânica do fêmur demonstrou que ambos os grupos treinados (PL+TR e CR+TR) apresentaram valores de força máxima significantemente maiores em relação aos grupos SHAM (p=0,024 e p=0,020, respectivamente), PL (p<0,001 e p<0,001) e CR (p=0,002 e p=0,002). Com relação à rigidez do fêmur, observou-se que o grupo SHAM não apresentou diferença significante quando comparado à ambos os grupos treinados (p=0,973 vs. PL+TR e p=0,998 vs. CR+TR), entretanto, apresentou diferença significante em relação aos grupos sedentários (p=0,048 vs. PL e p=0,024 vs. CR), ainda para esse parâmetro, o grupo PL apresentou diferença significante em relação ao grupo PL+TR (p=0,009), assim como o grupo CR foi significantemente diferente em relação ao grupo CR+TR (p=0,043). Não houve diferenças significantes entre os grupos PL e CR e entre os grupos PL+TR e CR+TR ao longo do estudo. Dessa forma, concluímos que a suplementação de creatina não apresentou efeitos isolados, nem aditivos, quando combinada ao treinamento físico, porém, o exercício físico promoveu efeitos positivos sobre o tecido ósseo, enfatizando, portanto, o seu papel terapêutico ímpar em atenuar a perda de massa óssea / The current literature indicates exercise training as one of the most used nonpharmacological strategies in the treatment and prevention of conditions that affect the bone tissue. Moreover, studies indicate that creatine supplementation may exert positive effects on bone mass gain. Thus, the aim of this study was to investigate the preventive effects of exercise training associated with creatine supplementation on bone loss in ovariectomized rats. Thus, sixty-five female Wistar rats were matched by body weight and randomly assigned into five experimental groups, as follows: 1) shammed (SHAM); 2) ovariectomized (OVX), sedentary and placebo-supplemented rats (PL); 3) OVX, sedentary and creatine-supplemented rats (CR); 4) OVX, trained and placebo-supplemented rats (PL+TR) and 5) OVX rats, trained and creatinesupplemented rats (CR+TR). The animals were submitted to a downhill running training protocol performed on a treadmill and supplemented with creatine on daily basis via gavage. Bone density were evaluated pre and post-intervention to obtain bone mineral content (BMC) and bone mineral density (BMD) from whole body and regional area, as well as body composition. Right femur was removed to biomechanical assessment. After the intervention, PL+TR group had higher BMC and BMD compared to the PL group (p=0.004 and p=0.020, respectively), while the CR+TR group experienced greater increases in BMC and tended to increase BMD compared to the CR group (p=0.011 and p=0.064, respectively). Biomechanical assessment demonstrated significantly higher femur maximum strength of both trained groups (PL+TR and CR+TR) compared to SHAM group (p=0.024 and p=0.020, respectively), PL group (p<0.001 and p<0.001) and CR group (p=0.002 and p=0.002). With respect to femur stiffness, no significant difference was observed from the SHAM group compared to both trained groups (p=0.973 vs. PL+TR and p=0.998 vs. CR+TR), however, significant difference was observed when compared to sedentary groups (p=0.048 vs. PL and p=0.024 vs. CR), moreover, significant difference was observed when the PL group was compared to PL+TR group (p=0.009), as well as the CR group was significantly different compared to the CR+TR group (p=0.043). There were no significant differences between PL and CR groups and between PL+TR and CR+TR groups along the study. Thus, we conclude that creatine supplementation showed no isolated, nor additive effects when combined with exercise training, however, exercise training promoted positive effects on bone tissue, thus emphasizing its unique therapeutic role in attenuating the loss of bone mass

Os materiais cerâmicos são utilizados pelo homem há milhares de anos e podem ser considerados os primeiros materiais utilizados na fabricação de ferramentas. Argamassas são materiais cerâmicos formados pela mistura de cimento, areia e água, são fluidos nas primeiras horas e endurecem com o tempo, ganhando resistência mecânica, já os refratários são materiais constituídos basicamente por duas partes, uma de granulometria fina denominada matriz e a outra de granulometria grosseira, chamada agregado, trabalham em altas temperaturas e muitas vezes sofrem choques térmicos. Devido a sua fragilidade, são susceptíveis a fratura catastrófica, por isso o conhecimento de seu comportamento mecânico é tão importante. Uma importante propriedade dos materiais cerâmicos é a energia de fratura e o método mais conhecido para a sua determinação é o da barra entalhada flexionada em três ou quatro pontos, porém o grande problema deste método é a relação de tamanho de agregado/área de fratura, pois como a barra apresenta, em geral, pequenas dimensões, o material pode apresentar um agregado de dimensões próximas à dimensão da área de fraturada e o resultado final pode ser fortemente afetado. Então, em 1986, Tschegg patenteou o método da cunha (wedge splitting test) que minimiza este efeito, devido à utilização de amostras com grande área de fratura. Desde então, este método vem sendo utilizado com freqüência por diversos pesquisadores no mundo. Porém não há estudos publicados que definam a posição ideal dos roletes do dispositivo de teste, levando ao uso de diferentes posições, sem que se saiba como isso pode influenciar o ensaio. Além de não existir uma definição de, a partir de que tamanho de agregado o método da barra entalhada passa a ser desaconselhável sendo necessário o uso do método da cunha. Neste trabalho analisou-se a influência da posição dos roletes e do tamanho de agregados nas medidas de energia de fratura e na carga máxima atingida no ensaio. / The ceramic materials are used by humans for thousands of years and can be considerate the first materials used in the manufacture of tools. Mortar are ceramic materials made by the mixture of cement, sand and water, it is fluid in the first hours and stiffen over time, gaining mechanical strength, the refractories in turn are made basically of two phases, one of fine granulometry called matrix and another of coarse called aggregate. It works over high temperature and many times suffer thermal shock. Due to its fragility, it is susceptible to catastrophic fracture; therefore the knowledge of its mechanical behavior is so important. One of the mainly properties of ceramic materials is the fracture energy and o most knew method for its determination is of three-point bending test on notched beams, but the biggest problem of this method is the relation between aggregate size and fracture area, because as the beam has small dimensions the aggregate can have a dimension so closed of the fracture area dimension and the final result can be tightly affect. Then in 1986, Tschegg patented the wedge splitting test, which minimizes this effect, because of the use of samples with a big fracture area. Since then, this method has been used for scientists around the world. But there are no studies that define the roll position of the test device, leading to the use of different positions, without know how it can influence the test. Besides not having a definition of from what aggregate size the wedge splitting test is advisable in despite of the bending test on notched beams. In this work was analyzed the influence of the rolls positions in the wedge splitting test and of the aggregate size in the measures of fracture energy and maximum load of test.

Most flows in nature and engineering are turbulent, and many are wall-bounded. Further, in turbulent flows, the turbulence generally has a large impact on the behavior of the flow. It is therefore important to be able to predict the effects of turbulence in such flows. The Navier-Stokes equations are known to be an excellent model of the turbulence phenomenon. In simple geometries and low Reynolds numbers, very accurate numerical solutions of the Navier-Stokes equations (direct numerical simulation, or DNS) have been used to study the details of turbulent flows. However, DNS of high Reynolds number turbulent flows in complex geometries is impractical because of the escalation of computational cost with Reynolds number, due to the increasing range of spatial and temporal scales. In Large Eddy Simulation (LES), only the large-scale turbulence is simulated, while the effects of the small scales are modeled (subgrid models). LES therefore reduces computational expense, allowing flows of higher Reynolds number and more complexity to be simulated. However, this is at the cost of the subgrid modeling problem. The goal of the current research is then to develop new subgrid models consistent with the statistical properties of turbulence. The modeling approach pursued here is that of "Optimal LES". Optimal LES is a framework for constructing models with minimum error relative to an ideal LES model. The multi-point statistics used as input to the optimal LES procedure can be gathered from DNS of the same flow. However, for an optimal LES to be truly predictive, we must free ourselves from dependence on existing DNS data. We have done this by obtaining the required statistics from theoretical models which we have developed. We derived a theoretical model for the three-point third-order velocity correlation for homogeneous, isotropic turbulence in the inertial range. This model is shown be a good representation of DNS data, and it is used to construct optimal quadratic subgrid models for LES of forced isotropic turbulence with results which agree well with theory and DNS. The model can also be filtered to determine the filtered two-point third-order correlation, which describes energy transfer among filtered (large) scales in LES. LES of wall-bounded flows with unresolved wall layers commonly exhibit good prediction of mean velocities and significant over-prediction of streamwise component energies in the near-wall region. We developed improved models for the nonlinear term in the filtered Navier-Stokes equation which result in better predicted streamwise component energies. These models involve (1) Reynolds decomposition of the nonlinear term and (2) evaluation of the pressure term, which removes the divergent part of the nonlinear models. These considerations significantly improved the performance of our optimal models, and we expect them to apply to other subgrid models as well. / text

Aluminium matrix composites are among the most promising candidate materials for light weight and high strength applications such as transportation and armour. In a previous study 6061 aluminum matrix composites reinforced with plain weave carbon fiber preform (AS4 Hexcel) were successfully fabricated by squeeze casting using the laminate fabrication technique. This research aims at optimizing the fabrication process in order to achieve improved strength and mechanical properties. It focuses on the liquid infiltration squeeze casting method. Good mechanical bonding between fiber and aluminium is achieved thanks to improved infiltration and impregnation of the fabric by liquid aluminium. Oxidation products at fiber/aluminium interface and porosity are reduced. As a result, composites are produced with overall improved mechanical properties. The flexural strength is increased by up to 19.9% and 15.4% compared to the laminate approach and the reference 6061 aluminium alloy squeeze cast under identical conditions, respectively. Similarly, overall hardness is improved. However, the impact strength is reduced by 7.76% and 25.78% when compared to casts fabricated by the laminate method and the reference aluminium alloy, respectively. The thesis constitutes a good basis for further research on fiber and particle reinforced aluminium matrix composites with the goal of further improving fracture toughness, particularly for gradient materials used in armour applications.

Os materiais cerâmicos são utilizados pelo homem há milhares de anos e podem ser considerados os primeiros materiais utilizados na fabricação de ferramentas. Argamassas são materiais cerâmicos formados pela mistura de cimento, areia e água, são fluidos nas primeiras horas e endurecem com o tempo, ganhando resistência mecânica, já os refratários são materiais constituídos basicamente por duas partes, uma de granulometria fina denominada matriz e a outra de granulometria grosseira, chamada agregado, trabalham em altas temperaturas e muitas vezes sofrem choques térmicos. Devido a sua fragilidade, são susceptíveis a fratura catastrófica, por isso o conhecimento de seu comportamento mecânico é tão importante. Uma importante propriedade dos materiais cerâmicos é a energia de fratura e o método mais conhecido para a sua determinação é o da barra entalhada flexionada em três ou quatro pontos, porém o grande problema deste método é a relação de tamanho de agregado/área de fratura, pois como a barra apresenta, em geral, pequenas dimensões, o material pode apresentar um agregado de dimensões próximas à dimensão da área de fraturada e o resultado final pode ser fortemente afetado. Então, em 1986, Tschegg patenteou o método da cunha (wedge splitting test) que minimiza este efeito, devido à utilização de amostras com grande área de fratura. Desde então, este método vem sendo utilizado com freqüência por diversos pesquisadores no mundo. Porém não há estudos publicados que definam a posição ideal dos roletes do dispositivo de teste, levando ao uso de diferentes posições, sem que se saiba como isso pode influenciar o ensaio. Além de não existir uma definição de, a partir de que tamanho de agregado o método da barra entalhada passa a ser desaconselhável sendo necessário o uso do método da cunha. Neste trabalho analisou-se a influência da posição dos roletes e do tamanho de agregados nas medidas de energia de fratura e na carga máxima atingida no ensaio. / The ceramic materials are used by humans for thousands of years and can be considerate the first materials used in the manufacture of tools. Mortar are ceramic materials made by the mixture of cement, sand and water, it is fluid in the first hours and stiffen over time, gaining mechanical strength, the refractories in turn are made basically of two phases, one of fine granulometry called matrix and another of coarse called aggregate. It works over high temperature and many times suffer thermal shock. Due to its fragility, it is susceptible to catastrophic fracture; therefore the knowledge of its mechanical behavior is so important. One of the mainly properties of ceramic materials is the fracture energy and o most knew method for its determination is of three-point bending test on notched beams, but the biggest problem of this method is the relation between aggregate size and fracture area, because as the beam has small dimensions the aggregate can have a dimension so closed of the fracture area dimension and the final result can be tightly affect. Then in 1986, Tschegg patented the wedge splitting test, which minimizes this effect, because of the use of samples with a big fracture area. Since then, this method has been used for scientists around the world. But there are no studies that define the roll position of the test device, leading to the use of different positions, without know how it can influence the test. Besides not having a definition of from what aggregate size the wedge splitting test is advisable in despite of the bending test on notched beams. In this work was analyzed the influence of the rolls positions in the wedge splitting test and of the aggregate size in the measures of fracture energy and maximum load of test.

Cette thèse est dédiée à l'étude de la fonction à trois points dans la théorie de jauge super-symétrique (SYM) N=4, dans la limite du grand nombre de couleurs, à l'aide de l'intégrabilité. La théorie de jauge N=4 SYM est invariante conforme au niveau quantique est on pense qu'elle est résoluble exactement. Par la correspondance AdS/CFT, elle est duale à la théorie des cordes de type IIB dans l'espace courbe AdS5× S5. Les fonctions à trois points sont des quantités qui contiennent de l'information essentielle sur la dynamique de la théorie.Nous passons en revue les méthodes déjà existantes et outils de l'intégrabilité qui sont nécessaires pour le calcul de la fonction à trois points. Nous présentons le calcul de la fonction à trois points dans le secteur SU(3), de rang supérieur à un, nous avons utilisé une représentation sous forme de déterminant, qui nous permets de prendre la limite semi-classique. En exploitant la relation entre des chaines de spin à langue portée et la chaine de Heisenberg inhomogène, nous avons développé une nouvelle pur calculer la fonction à trois points dans le secteur SU(2) à l'ordre d'une boucle qui nous permets d'obtenir le résultat dans une forme très compacte. Dans la limite de Frolov-Tseytlin ce résultat est en accord avec celui qu'on obtient au couplage fort.Nous avons exploré des nouvelles formulations de la fonction à trois points. En nous inspirant de la formulation de la théorie des champs des cordes dans la jauge du cone de lumière nous avons construit un vertex de spin, qui est la version de couplage faible du vertex des cordes, pour tous les secteurs à l'ordre des arbres. Cette approche peut être reliée au programme des facteurs de forme pour les théories de champs bi-dimensionnelles intégrables, dont nous rappelons ici les bases. Nous étudions la dépendance dans la taille du système pour une classe spéciale de fonction à trois points qui correspond aux facteurs de forme diagonaux. / This thesis is devoted to the study of three-point functions of N=4 Super-Yang-Mills (SYM) theory in the planar limit by using integrability. N=4 SYM theory is conformal invariant at quantum level and is believed to be completely solvable. By the AdS/CFT correspondence, it is dual to the type IIB superstring theory on the curved background AdS5×S5. The three-point functions are important quantities which contain essential dynamic information of the theory.The necessary tools in integrability and the existing methods of computing three-point functions are reviewed. We compute the three-point functions in the higher rank SU(3) sector and obtain a determinant representation for one special configuration, which allows us to take the semi-classical limit. By exploring the relation between long-range interacting spin chain and inhomogeneous XXX spin chain, we develop a new approach to compute three-point functions in the SU(2) sector at one-loop and obtain a compact result. In the Frolov-Tseytlin limit, this result matches the result at strong coupling.We also explore new formulations of the three-point functions. In one formulation inspired by the light-cone string field theory, we constructed the spin vertex, which is the weak coupling counterpart of the string vertex for all sectors at tree level. Another formulation which is related to the form factor boostrap program in integrable field theory is reviewed. At weak coupling, we study the finite volume dependence of a special type of three-point functions which are related to the diagonal form factors.

A literatura atual aponta o exercício físico como uma das estratégias nãofarmacológicas mais utilizadas no tratamento e prevenção de condições que acometem o tecido ósseo. Ademais, estudos indicam que a suplementação de creatina pode exercer efeitos positivos sobre o ganho de massa óssea. Sendo assim, o objetivo deste estudo foi investigar os efeitos preventivos do exercício físico associado à suplementação de creatina na perda de massa óssea em ratas ovariectomizadas. Diante disso, sessenta e cinco ratas da linhagem Wistar foram pareadas pelo peso corporal e dividas aleatoriamente em cinco grupos, sendo eles: 1) ratas falso-operadas (SHAM); 2) ratas ovariectomizadas (OVX), sedentárias e suplementadas com placebo (PL); 3) ratas OVX, sedentárias e suplementadas com creatina (CR); 4) ratas OVX, treinadas e suplementadas com placebo (PL+TR) e 5) ratas OVX, treinadas e suplementadas com creatina (CR+TR). Os animais foram submetidos a um protocolo de treinamento físico em declive em esteira rolante e suplementados com creatina diariamente por meio de gavagem esofágica. Foi realizada a avaliação de densitometria óssea para a obtenção dos parâmetros ósseos de conteúdo mineral ósseo (CMO) e densidade mineral óssea (DMO) de corpo total e regional, assim como a composição corporal nos períodos pré e pósintervenção. Além disso, foi removido o fêmur direito para a análise biomecânica. Após a intervenção, o grupo PL+TR apresentou maiores valores de CMO e DMO em comparação ao grupo PL (p=0,004 e p=0,020, respectivamente), ao passo que o grupo CR+TR experimentou maiores incrementos para o CMO e tendência ao aumento da DMO em comparação ao grupo CR (p=0,011 e p=0,064). A análise biomecânica do fêmur demonstrou que ambos os grupos treinados (PL+TR e CR+TR) apresentaram valores de força máxima significantemente maiores em relação aos grupos SHAM (p=0,024 e p=0,020, respectivamente), PL (p<0,001 e p<0,001) e CR (p=0,002 e p=0,002). Com relação à rigidez do fêmur, observou-se que o grupo SHAM não apresentou diferença significante quando comparado à ambos os grupos treinados (p=0,973 vs. PL+TR e p=0,998 vs. CR+TR), entretanto, apresentou diferença significante em relação aos grupos sedentários (p=0,048 vs. PL e p=0,024 vs. CR), ainda para esse parâmetro, o grupo PL apresentou diferença significante em relação ao grupo PL+TR (p=0,009), assim como o grupo CR foi significantemente diferente em relação ao grupo CR+TR (p=0,043). Não houve diferenças significantes entre os grupos PL e CR e entre os grupos PL+TR e CR+TR ao longo do estudo. Dessa forma, concluímos que a suplementação de creatina não apresentou efeitos isolados, nem aditivos, quando combinada ao treinamento físico, porém, o exercício físico promoveu efeitos positivos sobre o tecido ósseo, enfatizando, portanto, o seu papel terapêutico ímpar em atenuar a perda de massa óssea / The current literature indicates exercise training as one of the most used nonpharmacological strategies in the treatment and prevention of conditions that affect the bone tissue. Moreover, studies indicate that creatine supplementation may exert positive effects on bone mass gain. Thus, the aim of this study was to investigate the preventive effects of exercise training associated with creatine supplementation on bone loss in ovariectomized rats. Thus, sixty-five female Wistar rats were matched by body weight and randomly assigned into five experimental groups, as follows: 1) shammed (SHAM); 2) ovariectomized (OVX), sedentary and placebo-supplemented rats (PL); 3) OVX, sedentary and creatine-supplemented rats (CR); 4) OVX, trained and placebo-supplemented rats (PL+TR) and 5) OVX rats, trained and creatinesupplemented rats (CR+TR). The animals were submitted to a downhill running training protocol performed on a treadmill and supplemented with creatine on daily basis via gavage. Bone density were evaluated pre and post-intervention to obtain bone mineral content (BMC) and bone mineral density (BMD) from whole body and regional area, as well as body composition. Right femur was removed to biomechanical assessment. After the intervention, PL+TR group had higher BMC and BMD compared to the PL group (p=0.004 and p=0.020, respectively), while the CR+TR group experienced greater increases in BMC and tended to increase BMD compared to the CR group (p=0.011 and p=0.064, respectively). Biomechanical assessment demonstrated significantly higher femur maximum strength of both trained groups (PL+TR and CR+TR) compared to SHAM group (p=0.024 and p=0.020, respectively), PL group (p<0.001 and p<0.001) and CR group (p=0.002 and p=0.002). With respect to femur stiffness, no significant difference was observed from the SHAM group compared to both trained groups (p=0.973 vs. PL+TR and p=0.998 vs. CR+TR), however, significant difference was observed when compared to sedentary groups (p=0.048 vs. PL and p=0.024 vs. CR), moreover, significant difference was observed when the PL group was compared to PL+TR group (p=0.009), as well as the CR group was significantly different compared to the CR+TR group (p=0.043). There were no significant differences between PL and CR groups and between PL+TR and CR+TR groups along the study. Thus, we conclude that creatine supplementation showed no isolated, nor additive effects when combined with exercise training, however, exercise training promoted positive effects on bone tissue, thus emphasizing its unique therapeutic role in attenuating the loss of bone mass

La correspondance AdS/CFT est la première réalisation précise de la dualité jauge/gravité. Jusqu’à maintenant la correspondance AdS/CFT reste une conjecture. La dualité de N = 4 SYM et la théorie des cordes est un exemple le plus notable de correspondance AdS/CFT. Un des obstacles principaux à l’explorer est le fait que le régime de couplage faible pour la théorie de jauge est le régime de couplage fort pour la théorie des cordes et vice versa. Par conséquent, aussi longtemps que les méthodes perturbatives sont appliquées, on ne peut pas comparer les observables de deux cotés de la correspondance directement en dehors de quelques cas particuliers. A ce stade, l’énorme symétrie de N = 4 SYM joue un rôle important en permettant le calcul exact des observables de la théorie au moins dans la limite planaire. Cette thèse est consacrée au calcul des fonctions à trois, l’un des principaux observables de N = 4 SYM, et est composée de deux parties. Dans la première partie nous considérons l’approche générale pour le calcul des fonctions à trois points sur la base de soi-disant vertex de spin, qui est inspiré de la théorie de champs des cordes. Dans la deuxième partie, nous considérons un type spécifique de fonctions à trois points appelés lourd-lourd-léger, qui sont caractérisés par la propriété que la longueur de l’un des opérateurs est beaucoup plus petite des longueurs de deux autres. Il s’avère que ces fonctions de corrélations peuvent être identifiées à des facteurs de forme diagonaux et ainsi on peut appliquer les résultats concernant les facteurs de forme. / N=4 SYM theory has been drawing the attention of a lot of physicists during two last decades mainly due to the two aspects: AdS/CFT correspondence and integrability. AdS/CFT correspondence is the first precise realization of the gauge/string duality whose history starts in the 60's, when a string theory was considered as a candidate for describing the strong interactions. In 1997 Maldacena made a proposal about the duality between certain conformal field theories (CFT) and string theories defined on the product of AdS space and some compact manifold, which implies a one to one map between the observables of the gauge and string counterparts. Up to now AdS/CFT correspondence still remains a conjecture. The duality of N=4 SYM and the appropriate string counterpart is the most notable example of the AdS/CFT correspondence. One of the main obstructions to exploring it is the fact that weak coupling regime for the gauge theory is the strong coupling regime for the string theory and vice versa. Therefore as long as perturbative methods are applied, one can not compare the observables of dual counterparts directly apart from some specific cases. At this point the huge symmetry of N=4 SYM plays an important role allowing exact computation of the theory observables at least in the planar limit. This property of the theory is called integrability. The observables of the N=4 SYM are Wilson loops and correlation functions built out of gauge invariant operators. The space-time dependence of the two- and three-point correlators is fixed by the conformal symmetry up to some parameters: dimensions of the operators in the case of two-point functions and dimensions of the operators and structure constants in the case of three-point functions. It's commonly accepted to refer to the problem of finding the dimensions of the operators as the spectral problem. On the classical level the operator dimension is equal to the sum of the dimensions of the fundamental fields out of which the operator is composed. When the interaction is turned on, the conformal dimension gets quantum correction. In order to compute three-point functions, apart from the conformal dimensions of corresponding operators one needs to compute the structure constants. In CFT computation of the higher-point correlators eventually can be reduced to computation of two- and three-point functions by means of the operator product expansion. Therefore two- and three-point functions appear to be building blocks of any correlator of the theory. This thesis is devoted to computation of three-point functions and consists of two parts. In the first part we consider the general approach for computing three-point functions based on the so-called spin vertex, which is inspired from the string field theory. In the second part we consider a specific kind of three-point functions called heavy-heavy-light, which are characterized by the property that the length of one of the operators is much smaller the lengthes of other two. It happens that this kind of correlators can be considered as diagonal form factors which supposes that in this case one can apply the results obtained in the form factor theory.

The master thesis describes the methodology of laboratory and field measurements of tractors and tractor kits. It also contains graphical and tabular processing of measurement data and subsequent evaluation of the results obtained. It deals with the influence of power in the upper rod of three point hinge on wheel slip, work efficiency and fuel consumption.