Made available in DSpace on 2016-06-02T19:56:30Z (GMT). No. of bitstreams: 1 1801.pdf: 7196962 bytes, checksum: d8036f105e4f745f6d5cca6487bfd320 (MD5) Previous issue date: 2008-04-04 / Universidade Federal de Minas Gerais / The use of zeolites in the cracking of hydrocarbons is limited because the molecules higher than 0.74 nm do not diffuse in their micropores. In the other hand, molecular sieves as MCM-41, MCM-48 ou SBA-15, whose diameters are up 10 nm for the two formers and up to 30 nm for the last, have low hydrothermal stability and catalytic activity. To overcome those limitations, many studies are devoted to prepare materials, which can combine the high activity of zeolites with the better accessibility of the mesoporous materials. Among the possible methods, the synthesis of zeolites in confined spaces (nanocasting) it is seem as a powerful alternative. In this method: 1) a mesoporous or non-porous silica is impregnated with an organic compound, which act as a carbon precursor, after being carbonized; 2) the porous carbon is subsequently obtained by treatment with hydrofluoric acid or alkaline hydroxides; 3) the porous of the carbon are filled with the zeolite synthesis gel, which is formed after crystallization; 4) finally, the mold of the carbon and the template of the zeolite microstructure are eliminated by calcination. In the present work, it was used the above described method for the synthesis of nanocasting ZSM-5 zeolites using porous carbon, which were prepared from non-porous or mesoporous silica moulds (MCM-41, MCM-48 e SBA-15). The XRD of the prepared zeolites did not show diffraction peaks in the low angle region (< 5°2&#952;), showing that the inverse replica of the mesoporous silicas was not obtained. However, the nitrogen sorption measurements evidenced the presence of mesoporous, which resulted from the carbon nanotubes occluded during the ZSM-5 crystals formation. The mesopores observed in the Znp, nanocast from non-porous silica, were attributed to the inter-crystalline spaces generated by the agglomeration of ZSM-5 nanocrystals. The mesoporous formation in the ZSM-5 zeolites during the crystallization in a confined space (nanocating) was considerately favored by the ageing of the synthesis gel at the laboratory temperature and without stirring. That procedure allows the preparation at 180 °C of ZSM-5 zeolites with high crystallinity and in a lower time. Nevertheless, as verified by 27Al-NMR, the aluminum was incorporated partially in the zeolite microstructure, remaining as alumina in the crystal surface, which leads to a lower activity in the n-decane cracking when compared with a conventional ZSM-5 zeolite with a similar Si/Al ratio. / A utilização de zeólitas no craqueamento de hidrocarbonetos é limitada devido a não permitir a difusão de moléculas de tamanho maior que o diâmetro de seus microporos (< 0,74 nm). Por outro lado, as peneiras moleculares mesoporosas, como a MCM-41, MCM-48 ou SBA-15 com diâmetro de poros de até 10 nm, no caso das duas primeiras, e de até 30 nm no caso da última, possuem baixas estabilidade hidrotérmica e atividade catalítica. Para superar essas restrições, estuda-se a preparação de materiais que combinem a elevada atividade catalítica das zeólitas com a melhor acessibilidade dos materiais mesoporosos. Dentre os métodos possíveis, a síntese de zeóltas em espaço confinado (nanomoldagem), surge como uma potencial alternativa. Nessa técnica: 1) uma silica mesoporosa ou não porosa é impregnada com um composto orgânico precursor de carbono, sendo o sólido posteriormente carbonizado; 2) o carbono poroso é obtido após dissolução da sílica com ácido fluorídrico ou hidróxidos alcalinos; 3) os poros do carbono são preenchidos com o gel de síntese da zeólita, a qual se forma após cristalização; 4) finalmente o molde de carbono e o agente direcionador da microestrutura são eliminados via calcinação. No presente trabalho, utilizou-se a técnica descrita para a síntese de zeólitas ZSM-5 nanomoldadas em carbonos porosos, os que foram obtidos utilizando como molde sílicas não porosas ou mesoporosas (MCM-41, MCM-48 e SBA-15). Os difratogramas de raios X das zeólitas preparadas não apresentaram picos de difração em ângulos menores que 5°(2&#952;), mostrando que o ordenamento das fases mesoporosas não foi replicado, porém, os resultados de fisissorção de nitrogênio indicaram a presença de mesoporos, sugerindo que nanotubos de carbono formados nos mesoporos dos moldes de sílica foram ocluídos nos cristais da ZSM-5. Os mesoporos observados nas zeólitas Znp, nanomoldadas em carbono obtido da sílica não porosa, foram atribuídos aos espaços intercristalinos resultantes do empacotamento de cristais nanométricos da zeólita ZSM-5. A formação de mesoporos nas zeólitas ZSM-5 durante o processo de cristalização em espaço confinado (nanomoldagem) foi consideravelmente favorecida pelo envelhecimento do gel de síntese à temperatura ambiente e sem aplicação de agitação. Esse procedimento permitiu a obtenção a 180 °C de zeólitas com alta cristalinidade e em menor tempo de cristalização. Entretanto, como verificado por 27Al-RMN, o alumínio foi incorporado parcialmente na estrutura da zeólita, permanecendo como alumina na superfície dos cristais, o que provocou menor atividade para o craqueamento de n-decano quando comparado com uma zeólita ZSM-5 convencional com relação Si/Al próxima.

Submitted by Luiz Gustavo Possato null (gustavopossato@gmail.com) on 2017-01-18T15:52:06Z No. of bitstreams: 1 TeseFinal.pdf: 6256513 bytes, checksum: 5dc8457c0e05e4ba946b7acf2ad82ff8 (MD5) / Approved for entry into archive by LUIZA DE MENEZES ROMANETTO (luizamenezes@reitoria.unesp.br) on 2017-01-20T18:01:51Z (GMT) No. of bitstreams: 1 possato_lg_dr_araiq.pdf: 6256513 bytes, checksum: 5dc8457c0e05e4ba946b7acf2ad82ff8 (MD5) / Made available in DSpace on 2017-01-20T18:01:51Z (GMT). No. of bitstreams: 1 possato_lg_dr_araiq.pdf: 6256513 bytes, checksum: 5dc8457c0e05e4ba946b7acf2ad82ff8 (MD5) Previous issue date: 2016-12-12 / Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP) / O aumento da produção do biodiesel tem levado à formação de grandes quantidades de glicerol, o qual pode ser convertido em compostos de interesse petroquímico, como o ácido acrílico. A primeira parte consiste no estudo do comportamento de catalisadores bifuncionais V2O5/MFI com propriedades ácidas e oxidantes aplicados na desidratação oxidativa do glicerol em fase gasosa. Um dos principais produtos da reação foi o ácido acrílico (17%), produzido pela desidratação do glicerol à acroleína sítio ácido e sua subsequente oxidação em um sítio redox. A comparação da impregnação por via úmida com sulfato de vanadila (VOSO4) e metavanadato de amónio (NH4VO3) mostrou que a impregnação com VOSO4 forneceu o melhor desempenho para a conversão do glicerol e seletividade para o ácido acrílico. Medidas de XPS dos catalisadores frescos e usados auxiliaram a elucidação da dinâmica dos ciclos redox de óxido de vanádio durante a oxidação de acroleína. A presença de vanádio na zeólita aumentou a estabilidade do catalisador devido à capacidade multifuncional das espécies de óxido de vanádio para converter a acroleína e ácido acrílico e como catalisador para a oxidação dos produtos coqueificados da reação. Análises qualitativas e quantitativas do coque depositado nos catalisadores usados foram realizadas utilizando RMN de 13C e termogravimetria. A segunda parte está relacionada com a zeólita ZSM-5 (estrutura MFI, Si/Al = 40) tratada utilizando NaOH e ou ácido oxálico, ou HCI visando a obtenção de materiais com características hierárquicas diferentes, seguida pela impregnação com VOSO4 (precursor de V2O5) para gerar sítios redox. O impacto dos vários tratamentos na eficiência e a estabilidade dos catalisadores para a conversão de glicerol em acroleína e ácido acrílico (25%) foi investigada e correlacionada com porosidade catalisador, acidez e composição química. Os estudos demonstraram que o desempenho catalítico dos materiais dependeu das propriedades ácidas e texturais das zeólitas, que influenciaram tanto a dispersão de V2O5 quanto a sua interação com os sítios ácidos do suporte zeolítico A terceira parte apresenta um estudo in situ das fases cristalinas formadas durante o tratamento térmico de precursores de óxidos de vanádio e molibdénio, medidos por difração de raios X. O interesse na especiação de óxidos mistos MoxVyOz reside no excelente desempenho catalítico desses materiais para a conversão seletiva do glicerol ao ácido acrílico. A estrutura cristalográfica das fases ativas de MoxVyOz influencia diretamente sobre a valência do vanádio e, consequentemente, altera as dinâmicas dos estados de oxidação do vanádio durante a reação catalítica. O tratamento térmico de uma mistura de precursores de Mo e V sob atmosferas oxidante ou inerte revelou a maior formação de MoV2O8 (61%) ou de Mo4V6O25 (29%), respectivamente, a uma temperatura final de 500 °C. A fase mais ativa para a formação do ácido acrílico foi MoV2O8 (3,5 vezes mais ativa do que os óxidos dos metais separados), devido à instabilidade da fase em relação ao oxigênio de rede na temperatura da reação. O ciclo de redução e oxidação do vanádio em MoV2O8 durante a reação auxiliou a dinâmica da criação de vacâncias de oxigênio, resultando em 97% de conversão de glicerol e 32% de seletividade ao ácido acrílico. A quarta e última parte é relacionada à dispersão dos óxidos mistos de vanádio e molibdênio na matriz zeolítica. / The increased production of biodiesel has led to the formation of large amounts of glycerol, which can be converted into compounds of petrochemical interest, such as acrylic acid. The first part consists in the study of catalytic behavior of bifunctional V2O5/MFI catalysts with acid and oxidizing properties investigated for the gas-phase oxidehydration of glycerol. One of the main reaction products was acrylic acid, produced by dehydration of glycerol to acrolein at an acidic site and subsequent oxidation at a redox site. Comparison of wet impregnation with vanadyl sulfate (VOSO4) and ammonium metavanadate (NH4VO3) showed that VOSO4 impregnation provided the best performance for the conversion of glycerol and selectivity towards acrylic acid (17%). XPS measurements of the fresh and spent catalysts enabled elucidation of the dynamic redox cycles of vanadium oxide during oxidation of acrolein. The presence of vanadium in the zeolite improved the catalyst lifetime, because of the multifunctional ability of the vanadium oxide species to convert acrolein to acrylic acid and act as catalyst for the oxidation of coked glycerol products. Qualitative and quantitative analyses of the coke deposited in the spent catalysts were performed using 13C NMR and thermogravimetry, respectively. The second chapter is related to ZSM-5 zeolite (MFI structure, Si/Al = 40) treated using NaOH and either oxalic acid or HCl to obtain hierarchical materials with different characteristics, followed by impregnation with vanadium oxides (V2O5) to generate redox-active sites. The impact of the multiple treatments on the efficiency and stability of the catalysts in the conversion of glycerol to acrolein and acrylic acid (25%) was investigated and correlated with catalyst porosity, acidity, and chemical composition. The studies showed that the catalytic performance of the materials depended on the acidic and textural properties of the zeolites, which influenced both the dispersion of V2O5 and its interaction with the acid sites of the supporting zeolites. The third part presents an in situ study of the crystallographic phases formed during the thermal treatment of precursors of vanadium and molybdenum oxides, measured under synchrotron X-ray diffraction. The interest in the speciation of MoxVyOz mixed oxides lies in the excellent catalytic performance of these materials for the selective conversion of glycerol to acrylic acid employing the oxidehydration reaction. The crystallographic structure of the active phases of MoxVyOz directly influences on the nearby metal valence and, therefore, on the dynamic changes in metal oxidation states during the catalytic reaction. The thermal treatment of a mixture of the precursors of Mo and V under oxidizing or inert atmospheres revealed the major formation of 61 % of MoV2O8 or 29 % of Mo4V6O25, respectively, at a final temperature of 500 ºC. The most active phase for acrylic acid formation was MoV2O8 (3.5 times more active than the separate metal oxides), due to the instability of the phase with respect to framework oxygen at the reaction temperature. The cycle of reduction and oxidation of the vanadium in MoV2O8 during the reaction caused dynamic creation of oxygen vacancies, resulting in 97 % conversion of glycerol and 32 % selectivity towards acrylic acid. The fourth and last part is related to the mixed oxides dispersed on the zeolite support. / FAPESP: 2013/10204-2

Submitted by Automa??o e Estat?stica (sst@bczm.ufrn.br) on 2018-04-11T19:34:25Z No. of bitstreams: 1 JulianaElionaraBezerraCosta_TESE.pdf: 2543108 bytes, checksum: 556e8d7316f4202efa7113ded946013c (MD5) / Approved for entry into archive by Arlan Eloi Leite Silva (eloihistoriador@yahoo.com.br) on 2018-04-12T22:40:15Z (GMT) No. of bitstreams: 1 JulianaElionaraBezerraCosta_TESE.pdf: 2543108 bytes, checksum: 556e8d7316f4202efa7113ded946013c (MD5) / Made available in DSpace on 2018-04-12T22:40:16Z (GMT). No. of bitstreams: 1 JulianaElionaraBezerraCosta_TESE.pdf: 2543108 bytes, checksum: 556e8d7316f4202efa7113ded946013c (MD5) Previous issue date: 2017-12-18 / Coordena??o de Aperfei?oamento de Pessoal de N?vel Superior (CAPES) / Alguns res?duos, provenientes das mais variadas atividades, podem ser reaproveitados, diminuindo o efeito dos impactos ambientais ocasionados pela m? disposi??o dos mesmos no meio ambiente. Os res?duos classificados com biomassa lignocelul?sica, podem ser convertidos em produtos qu?micos e combust?veis a partir da pir?lise r?pida convencional, gerando como produto principal o bio-?leo com caracter?sticas diretamente ligadas as caracter?sticas da biomassa de origem que podem ser melhoradas a partir do uso de catalisadores. Neste trabalho foram sintetizados catalisadores do tipo ZSM-5 e HZSM-5, utilizando res?duos de p? de granito, p? de vidro, diatomita e cinza da casca do arroz como fontes alternativas e tamb?m um catalisador utilizando fonte convencional de S?lica e Alum?nio. O objetivo da s?ntese desses materiais ? utiliz?-los como catalisador na pir?lise da fibra do coco visando a obten??o de produtos com maior valor agregado, reduzindo a produ??o de compostos oxigenados. A biomassa utilizada foi caracterizada por an?lise imediata, densidade, an?lise elementar, Teor de Celulose, hemicelulose e lignina, Poder calor?fico, TG/DTG, DRX, FT-IR e FRX afim de analisar o potencial energ?tico da mesma. Os precursores de S?lica e Alum?nio foram submetidos a an?lises de FRX, DRX, e os catalisadores foram caracterizados por TG/DTG, DRX, FT-IR, MEV e BET. Nos resultados de pir?lise convencional da fibra do coco observou a grande produ??o de produtos oxigenados, a maior parte deles fen?is e nos resultados das pir?lise catal?tica foi poss?vel observar a diminui??o desses produtos, provando a efici?ncia dos catalisadores utilizados. / Some waste, from the most varied activities, can be reused, reducing the effect of these impacts, usually caused by poor disposal in the environment. The residues classified with lignocellulosic biomass can be converted into chemical products and fuels from the conventional fast pyrolysis, generating as main product the bio-oil. This generally presents some undesirable characteristics directly linked to the characteristics of the source biomass, which decrease its energy efficiency. The use of catalysts allows the reduction of these undesirable products and improves the final quality of the bio oil. As a result, ZSM-5 and HZSM-5 catalysts were synthesized using granite powder, glass powder, diatomite and rice husk ash as alternative sources of silica and aluminum; was also synthesized using a conventional silica and aluminum source, serving as a standard for the others. . The objective of the synthesis of these materials is to use them as a catalyst in the pyrolysis of coconut fiber in order to obtain products with higher added value, reducing the production of oxygenated compounds. The biomass used was characterized by immediate analysis, density, elemental analysis, cellulose content, hemicellulose and lignin, calorific power, TG / DTG, XRD, FT-IR and FRX in order to analyze the energy potential of the same. Silica and Aluminum precursors were subjected to FRX, XRD analyzes, and the catalysts were characterized by TG / DTG, DRX, FT-IR, MEV and BET. In the results of conventional pyrolysis of the coconut fiber, it was observed the great production of oxygenated products, most of them phenols and in the results of the catalytic pyrolysis it was possible to observe the decrease of these products, proving the efficiency of the catalysts used.

Fossil based energy resources are dominating the world’s primary energy consumption for the last century. However, with decreasing crude oil reservoirs and the role they play in global warming by emitting greenhouse gases, the focus has been turned towards improved utilization of renewable resources and the need for new, sustainable fuels and chemicals is more urgent than ever. Biomass is a carbon neutral resource that can be used to produce biofuels and other useful chemicals. One such chemical is 1-butanol (or simply butanol), which has great potential as a gasoline substitute because of its favorable fuel properties. Butanol can be produced from acetone, butanol and ethanol (ABE) fermentation using e.g. Clostridium acetobutylicum. However, the concentration of butanol in fermentation in the resulting broth is limited to ca. 20 g/L due to its toxicity for microorganisms. Butyric acid is a precursor to butanol, which is produced prior to butanol in ABE fermentation. Butyric acid is an important industrial chemical, which can be further converted into a number of commercial compounds e.g. acetate butyrate, butyl acetate and butanol. Arginine is a semi-essential amino acid that has vast applications in the field of pharmaceutical and food industry. In addition, arginine can replace inorganic nitrogen as nitrogen source in fertilizers. It can be produced via fermentation of sugars using engineered microorganism like E. Coli, but like butanol its concentration is restricted to approximately 12 g/L. Due to low concentration of these useful chemicals in the resulting fermentation broths recovery of these chemicals remain challenging with today’s options and therefore  novel recovery process should be developed. In this study, zeolite adsorbents were used to recover butanol, butyric acid and arginine from model and real fermentation broths. Zeolite MFI adsorbent efficiently adsorbed butanol from model solutions with a saturation loading of 0.11 g/g- zeolite. On the other hand, adsorption of butyric acid was found to be strongly pH dependent, with high adsorption below and little adsorption above the pKa value of the acid. A structured adsorbent in the form of steel monolith coated with a silicalite-1 film was also used and performance was evaluated by performing breakthrough experiments at room temperature using model ABE fermentation broths and the results were compared with those obtained using traditional adsorbent sin the form of beads. Desorption studies showed that a high quality butanol product with purity up to 95.2% for butanol-water system and 88.5% for the ABE system can be recovered with the structured silicalite-1 adsorbent. Further, zeolite X adsorbents in the form of powder and extrudates was used to recover arginine from a real fermentation broth and also from aqueous model solutions. To the best of our knowledge, this is the first time recovery of arginine from real fermentation broths using any type of adsorbent is reported. Arginine loading of 0.15 g/g was observed at pH 11 using zeolite X powder. The selectivity for arginine over ammonia and alanine from the fermentation broth at pH 11 was 1.9 and 8.3, respectively, for powder and 1.0 and 4.1, respectively, for extrudates. Synthesis gas (CO + H2) can be produced e.g.by gasification of lignocellulose biomass. This synthesis gas can be used to produce methanol, which subsequently may be converted into gasoline using zeolite ZSM-5 catalyst. However, during Methanol to Gasoline (MTG) process, undesirable carbon residue (coke) is formed that gradually reduces the activity of catalyst. It was hypothesized that intracrystalline defects in the zeolite formed during conventional synthesis may accelerate the deactivation rate by coke formation. In this work, a novel ZSM-5 zeolite catalyst essentially free of intracrystalline defects was synthesized and evaluated in the  MTG reaction,. The novel catalyst showed significantly higher resistance towards deactivation by coke formation as compared to a reference catalyst containing defects.

Zeolites and zeolite membranes are two important advanced chemical materials which are widely used in chemical processes. The manufacture of these materials usually involves the use of expensive chemicals. This study involves the use of Ahoko Nigerian kaolin (ANK) as precursor material for the development of zeolites and zeolite membranes. The synthesis of zeolite A, Y and ZSM-5 was successfully obtained following a sequence, collection of the raw clay from Nigeria, metakaolinization, dealumination and actual hydrothermal synthesis of the zeolites. Raw ANK was refined using sedimentation technique and about 97% kaolin was recovered from the raw sample. A novel metakaolinization technique was developed to convert kaolin into a reactive metastable phase. Amorphous metakaolin was obtained at a temperature of 600°C and exposure time of 10 min. This is a significant result because previous studies use higher temperatures and longer exposure times for the metakaolinization step. The metakaolin was used to prepare a number of different zeolites under various conditions. Highly crystalline zeolite A was obtained at an ageing time of 12 h, crystallization time of 6 h and crystallization temperature of 100oC. Zeolite Y was obtained at an ageing time of 3 h, crystallization time of 9 h and crystallization temperature of 100oC. Zeolite Y was also synthesised by using a dealuminated kaolin and highly crystallized zeolite Y with Si/Al ratio of 1.56 and BET surface area was obtained of 630 m2/g. ZSM-5 was synthesised using an ageing period of 36 h, crystallization time of 48 h and temperature of 140oC. The results obtained from zeolite powder synthesis from ANK were then used as guide to prepare supported zeolite films and membranes by a hydrothermal method. The effect of the support surface (stainless steel) was investigated using two synthesis methods namely modified in-situ and secondary (seeded) growth. Zeolite A, Y and ZSM-5 films were successfully prepared from ANK for the first time and on two modified supports, etched and oxidised. The zeolite films and membranes developed showed complete coverage on the two supports with the oxidised showing better adhesion and intergrowth. The separation performance of the three developed zeolite membrane was tested by pervaporation of water/ethanol mixture. The results of pervaporation of ethanol/water mixture showed that zeolite A membrane is highly selective towards water mainly because of hydrophilic properties occasioned by the high aluminium content. Zeolite Y membrane show a similar response when their separation performance was evaluated but with less selectivity because of reduced aluminium content. ZSM-5 showed selectivity towards ethanol because of it hydrophobicity allowing only ethanol to permeate. In all the zeolite membranes, the flux is lower in comparison to commercial zeolite membranes due mainly to the thickness of the zeolite layer. Oxidised support membranes showed better performance because of their better interaction between the oxide surface and the aluminosilicate gel. The results show that ANK can successfully be used to prepare zeolites and zeolite membrane.

Previous studies have successfully used near and supercritical water (SCW) for cracking and desulfurization of heavy crude oil and bio-oil, suppressing coke formation as a low-value by-product. Some of these studies benefited from using zeolite catalysts to increase the activity and selectivity toward targeted products; however, in depth studies are required to identify the role of water on zeolite catalysis under supercritical condition. Using three common zeolites, ZSM-5, HY, and β for supercritical water cracking of dodecane at 400°C, 24±2 MPa (in a 100 ml batch reactor), we showed that ZSM-5 is the only catalyst that partially retains its crystalline structure and activity under hydrothermal conditions. Further characterization of the ZSM-5 (used under 50/50 wt% SCW/dodecane feed) revealed 95% decrease in Brønsted acid site (BAS) density and 80% decrease in microporous area after 2 h reaction time. However, compared to the runs where SCW was absent, the apparent dodecane cracking rate constant in SCW decreased only by a factor of 2.6. Examining catalytic activity of ZSM-5 degradation products and re-using ZSM-5 showed that the unexpected activity cannot be ascribed to ZSM-5 degradation products. Using a group-type model, we showed that SCW accelerated gas and suppressed coke formations. Additionally a coke gasification pathway was suggested to account for formation of CO and CO2 in the presence of SCW. Additional experiments with two different ZSM-5 particle sizes suggested that dodecane cracking reaction is diffusion-limited in the absence of SCW and reaction-limited in its presence. Zero length chromatography of calcined and hydrothermally treated ZSM-5 showed 10 times greater apparent diffusivity for un-treated catalyst. This, according to Weisz-Prater analysis, suggested a 250 times greater dodecane surface concentration in the absence of SCW. We successfully optimized the water content of feed (5-15 wt%) to decrease the destructive effects of SCW on the structure, increase the selectivity toward BTEX products and eliminate coke formation.

Previous studies have successfully used near and supercritical water (SCW) for cracking and desulfurization of heavy crude oil and bio-oil, suppressing coke formation as a low-value by-product. Some of these studies benefited from using zeolite catalysts to increase the activity and selectivity toward targeted products; however, in depth studies are required to identify the role of water on zeolite catalysis under supercritical condition. Using three common zeolites, ZSM-5, HY, and β for supercritical water cracking of dodecane at 400°C, 24±2 MPa (in a 100 ml batch reactor), we showed that ZSM-5 is the only catalyst that partially retains its crystalline structure and activity under hydrothermal conditions. Further characterization of the ZSM-5 (used under 50/50 wt% SCW/dodecane feed) revealed 95% decrease in Brønsted acid site (BAS) density and 80% decrease in microporous area after 2 h reaction time. However, compared to the runs where SCW was absent, the apparent dodecane cracking rate constant in SCW decreased only by a factor of 2.6. Examining catalytic activity of ZSM-5 degradation products and re-using ZSM-5 showed that the unexpected activity cannot be ascribed to ZSM-5 degradation products. Using a group-type model, we showed that SCW accelerated gas and suppressed coke formations. Additionally a coke gasification pathway was suggested to account for formation of CO and CO2 in the presence of SCW. Additional experiments with two different ZSM-5 particle sizes suggested that dodecane cracking reaction is diffusion-limited in the absence of SCW and reaction-limited in its presence. Zero length chromatography of calcined and hydrothermally treated ZSM-5 showed 10 times greater apparent diffusivity for un-treated catalyst. This, according to Weisz-Prater analysis, suggested a 250 times greater dodecane surface concentration in the absence of SCW. We successfully optimized the water content of feed (5-15 wt%) to decrease the destructive effects of SCW on the structure, increase the selectivity toward BTEX products and eliminate coke formation.

<p>  </p> <p>Cyclar process was previously developed to convert propane and butane into aromatics using gallium-promoted ZSM-5 zeolites (Ga/ZSM-5). However, it has two major limitations. Firstly, light gases (methane and ethane) limit the yield of higher molecular weight hydrocarbons for propane conversion. Secondly, ethane is unreactive on Ga/ZSM-5 catalysts. Relative rates and selectivity for propane conversion on two components, gallium (Ga/Al2O3) and acid ZSM-5 (H-ZSM-5) were investigated, and the results suggest that light gas was produced by propane monomolecular cracking on ZSM-5 due to the imbalance of alkane dehydrogenation and olefin conversion rates on two catalytic functions. A PtZn alloy catalyst, which has >99% propene selectivity and 30 times higher rate than Ga, was used for the dehydrogenation function. The bifunctional PtZn/SiO2+ZSM-5 catalyst has high yields of aromatics with low methane selectivity (<5%) at ~70% propane conversion. The results suggest methane can be minimized by utilizing the PtZn alloy and lowering the monomolecular cracking rate by ZSM-5. In addition, PtZn alloy increases aromatics selectivity. Aromatics formation pathway was investigated by studying the rate and selectivity of a model intermediate (cyclohexene) on ZSM-5, PtZn/SiO2 and Ga/Al2O3. Benzene is formed at similar rates on Ga/Al2O3 and ZSM-5 but cracking of cyclohexene on the latter is two orders of magnitude higher than the benzene formation rate, indicating cracking of cyclic hydrocarbons leads to low aromatization rate on Ga/ZSM-5. The benzene formation rate on the PtZn/SiO2 is 200 times higher than that on ZSM-5, suggesting aromatics are formed by the metal pathway on PtZn/SiO2+ZSM-5. </p> <p>Unlike Ga/ZSM-5 catalysts, PtZn/SiO2+ZSM-5 catalysts also convert propane to aromatics at low temperature (350 ℃). The temperature effect on propane dehydroaromatization pathways on the PtZn/SiO2+ZSM-5 bifunctional catalysts was investigated to develop strategies for propane conversion to valuable liquid hydrocarbons. At high temperature (550 ℃), high dehydrogenation rates and lower monomolecular cracking rates are required to minimize methane formation, leading to primarily propene and BTX (benzene, toluene, and xylenes). By recycling propene in the propane conversion range of 30-45%, >80% BTX yields is likely achievable at full recycle. At mid temperature (400-450 ℃), the product has high selectivity to gasoline-blending hydrocarbons (butanes, C5+ hydrocarbons, toluene, and xylenes) at 15-25% propane conversions because dehydrogenation rates are moderately high, and oligomerization is more favored than cracking. At low temperature (350℃), ~25% propane conversion is achieved and has high selectivity (~60%) to butanes, but the propane conversion rates are likely too low to be practical. While methane formation by monomolecular cracking limits liquid yields at high reaction temperature, at mid and low temperatures, hydrogen co-produced at high propane conversions saturates light olefins to make undesired ethane, which becomes major yield-loss reaction on the PtZn/SiO2+ZSM-5. </p> <p>Finally, PtZn/SiO2+ZSM-5 catalysts can convert ethane to C3+ and aromatics but the methane selectivity increases rapidly at high ethane conversion. The roles of two catalytic function (Pt-Zn alloy and ZSM-5) in the dehydroaromatization pathways of ethane and propane will be further studied and their product distribution will be compared to have better understandings on the differences in the dominant yield-loss reaction and dehydroaromatization pathways. </p>

The increasing production of natural gas liquids attracts both academia and industry to develop on-purpose techniques converting those light alkanes to value-added chemicals. Dehydroaromatization is an alternative path for light alkane conversion to produce aromatics but still lacks active and stable catalysts. This work aims at the development of efficient dehydroaromatization catalysts by tuning the metal/acid bifunctionality of the Pt/HZSM-5 catalyst. Additionally, through co-processing light alkane with ammonia during the dehydroaromatization process, this study also proposes a new reaction system that could directly link the C-N bond for nitrile synthesis. The results suggested that the activity, selectivity, and stability of the monometallic Pt/HZSM-5 catalyst are highly dependent upon the Pt loading, the limit loading of 100 ppm is required to maintain sufficient metal functionality. To further minimize the Pt loading, the chemical properties of the Pt species were tuned by a second metal such as Zn or Cu. Consequently, the activity and stability of the catalyst are enhanced by orders of magnitude and the maximized metal functionality was achieved at Pt loading of 10 ppm. Characterizations show that Pt can be atomically dispersed as a hybrid [Pt1-Zn6] cluster in the Pt-Zn@HZSM-5 or forming single atom alloy type [Pt1-Cu4] ensembles in the Pt-Cu@HZSM-5. Specifically, the initial turnover frequencies of propane and ethane to BTX are up to 178.8 and 128.7 s-1 over the Pt-Cu@HZSM-5, up to 3-4 orders of magnitude higher than the state-of-the-art Pt-based catalyst. Furthermore, the deactivated catalyst can be continuously regenerated, demonstrating excellent stability of such a catalyst under hash oxidation conditions for coke burn-off. A new catalytic system named ammodehydrogenation (ADeH) for ethane selective conversion to acetonitrile, ethylene, and hydrogen over a bifunctional catalyst is proposed. Ethane ADeH over the Pt/HZSM-5 catalyst is active at low temperatures and atmospheric pressure for CH3CN production. The Pt/HZSM-5 shows high coke-resistibility during the ethane ADeH due to the strong interaction of NH3 with the acid sites of the catalyst. The catalyst can be further optimized by adding Co, the Pt-Co/HZSM-5 catalyst on ethane ADeH indicating that an appropriate balance between the metal and acid functionalities is critical for ethane ADeH.

Yes / The adsorption of acid gas, including hydrogen sulfide and carbon dioxide, by superhigh silica ZSM-5 was investigated. Equilibrium adsorption isotherms of high-purity hydrogen sulfide and carbon dioxide were measured experimentally using this new sorbent. In addition, methane and nitrogen adsorption isotherms on this MFI-type zeolite were also measured as representative of other natural gas components. To enhance the reliability of the results, the adsorption pressure has been selected up to 20 bar at three different temperatures. Superhigh silica ZSM-5 for the adsorption of hydrogen sulfide shows an impressive result of 3.04 mmol·g–1 at 12 bar and 283 K. This value was 2.69 mmol·g–1 for carbon dioxide at 21 bar and 283 K. The adsorption capacity of H2S on the ZSM-5 is the highest, and N2 is the lowest; the order of the adsorption capacities of components is H2S > CO2 > CH4 > N2. The adsorption heat of different adsorbates is calculated: 13.7 and 29.5 kJ·mol–1 for H2S and CO2, respectively. Physical adsorption has occurred on high-silica ZSM-5, especially for hydrogen sulfide, and this is a great advantage. By increasing the temperature, the adsorption capacity of components on the ZSM-5 decreases, but due to differences in the adsorption heat of the adsorbate, the ideal selectivity for hydrogen sulfide increases. There is a challenge in the choice of the best condition for H2S removal, as, by increasing the temperature, the adsorption capacity of hydrogen sulfide reduces, but the selectivity of the hydrogen sulfide increases as compared to other gases. This phenomenon is not true for the selectivity of other components.