The aim of this work was to develop the method for the determination of the superperplasticizers (SP) content in the water solution. The method developed was then applied to study the SP adsorption on the individual components used for high-performance concrete and the influence of the temperature and pH values over this adsorption. Furthermore the influence of the water to binder ratio, SP, finely grounded granulated blast furnace slag, fly ash, silica fume, finely ground silica sand and bauxite on the hydration process was studied by means of isoperibolic, isothermal and solution calorimetry. The compressive and flexural strength of most samples used in calorimetric experiments was also determined.

<p>Superabsorbent polymer (SAP) hydrogel particles have been used as internal curing agents in concrete mixes as they are capable of absorbing and subsequently releasing large amounts of water. This reduces autogenous shrinkage during early stages of hydration. The size, shape, and composition of the hydrogel particles can be controlled during the synthesis, hence providing the opportunity to custom synthesize these internal curing agents to elicit desired structure-property relationships. Utilization of optimized dosage and formulation of SAP has the potential to improve the microstructure, durability, and strength of internally cured concrete. </p> <p>The first study focuses on the synthesis and application of novel composite hydrogel particles as internal curing agents in cementitious mixes. Composite polyacrylamide hydrogel particles containing two different amorphous silica–either nanosilica or silica fume–were used to investigate whether the internal curing performance of hydrogel particles could be enhanced. The dosage and type of silica, crosslinker amount were varied to identify the composite polyacrylamide hydrogel particle composition that provides optimum benefits to internally cured cementitious systems. The synthesized hydrogels were characterized by means of absorption capacity tests, compositional and size analysis. The beneficial impacts of the addition of composite hydrogels on cement paste microstructure are highlighted, including the preferential formation of cement hydration products (such as portlandite) within the hydrogel-induced voids that appeared to be influenced by the composition of the hydrogel particles. The interrelationship between extent of hydration, size of hydrogel voids, and void-filling with hydration products was found to strongly influence mechanical strength and is thus an important structure-property relationship to consider when selecting hydrogels for internal curing purposes. This study informs the design of composite hydrogel particles to optimize performance in cementitious mixes. Additionally, it provides a novel means of incorporating other commonly used admixtures in concrete without facing common challenges related to dispersion and health hazards.</p> <p>The second study focuses on the utilization of two retarding admixture-citric acid and sucrose-to custom synthesize composite polyacrylamides to investigate whether the composite hydrogels could delay hydration of cement paste. Isothermal calorimetry analysis results showed that composite sucrose-containing polyacrylamide hydrogel particles were successfully able to retard main hydration peak of cement paste, beyond the retardation capabilities of the pure polyacrylamide hydrogels. Thus, this study provides avenues of exploring the utilization of common admixtures to formulate novel composite hydrogels that imparts specific properties to cementitious systems.</p> <p>In another study, SAP formulated by admixture industries were used to investigate the feasibility of internal curing of bridge decks and pavement patches with SAP particles. The microstructure and early age hydration properties of SAP-cured cementitious systems were studied. Mitigation of microcracks in the matrix, along with portlandite growth in SAP voids, were observed in SAP-cured mortars. Presence of SAP also mitigated autogenous shrinkage and improved early age hydration as observed by isothermal calorimetry analysis. This thesis highlights some of the beneficial impacts of SAP-cured cementitious systems, and the potential to harness those benefits in large-scale applications of SAP-cured concrete.</p> <br>

Esta pesquisa trata da estabilização de misturas de agregados reciclados por meio da ativação de seus finos, cujas composições possibilitam a ocorrência de reações químicas de cimentação. Para o desenvolvimento da pesquisa foram utilizados dois tipos de agregados reciclados: um proveniente de resíduo de demolição de natureza cimentícia e outro da indústria de cerâmica vermelha. O uso dos materiais foi feito por meio de dosagens para obtenção de misturas cujas combinações de materiais pudessem, quimicamente, potencializar a ocorrência de hidratação do cimento anidro existente nos finos do agregado reciclado cimentício e de reação pozolânica pela pozolanicidade da cerâmica vermelha. Com isso foram obtidas cinco misturas, compostas pelos agregados reciclados em estudo misturados entre si e com a adição de aglomerantes hidráulicos, sobre as quais foram realizados ensaios em laboratório para verificação da ocorrência das reações químicas esperadas com consequente estabilização das misturas, de modo a influenciar nos respectivos comportamentos mecânicos. Também foi realizada a avaliação de características do empacotamento dos grãos como forma de verificar se o arranjo físico, neste caso, exerce influência significativa na melhora do comportamento mecânico das misturas estudadas. Os resultados obtidos indicaram que, de fato, ocorreram as reações químicas esperadas, comprovadas pelos resultados dos ensaios de termogravimetria e difração de raios x, realizados em três diferentes idades de cura. Verificou-se, também, a melhora no comportamento mecânico das misturas por meio do aumento da resistência à compressão simples e do módulo de resiliência com a evolução da cura, além de baixa deformabilidade aos 91 dias de cura. Com isso foi comprovada a estabilização das misturas em estudo, com a consequente melhora de seus desempenhos, sendo devida, principalmente, à ocorrência das reações químicas de hidratação do cimento anidro e pozolânica. A pesquisa demonstrou a possibilidade de se estabilizar misturas de agregados reciclados cimentícios e de cerâmica vermelha por meio da ocorrência de reações químicas de cimentação promovidas pela combinação destes materiais. / This research deals with the stabilization of mixtures constituted by recycled aggregates through the activation of its fines portions, whose components enable the occurrence of chemical cementation reactions. In order to develop this research, two types of recycled aggregates were used: one from demolition waste with cementitious origin, and the other one from the red ceramic industry. The use of these materials was done through mix designs to obtain mixtures whose combinations of materials could chemically increase the occurrence of hydration of the anhydrous existing in fine portion of the recycled cementitious aggregates, and pozzolanic reactions due to the pozzolanicity of red ceramics. Thus, five mixtures were obtained, and they were composed by the studied recycled aggregates, mixed together and with the addition of hydraulic binders, on which laboratory tests were performed in order to verify the occurrence of the expected chemical reactions with consequent stabilization of the mixtures, in order to influence their mechanical behavior. Furthermore, it was performed the evaluation of packing characteristics of the particles to verify if the physical arrangement, in this case, has any significant influence on improving the mechanical behavior of the mixtures studied. The results obtained indicated that in fact the expected chemical reactions occurred, which was verified by the results from thermogravimetry and X-ray diffraction tests performed at three different times of curing. The improvement of the mixtures mechanical behavior by increasing of their compressive strength and their resilient modulus was also verified as the mixtures were cured, in addition to low deformability at 91 days of curing. Thus, the stabilization of the mixtures studied was confirmed, which was mainly due to the occurrence of chemical hydration reactions of the anhydrous cement and pozzolanic reactions. The study demonstrated the possibility of stabilizing mixtures of recycled aggregates cementitious waste and red ceramic by the occurrence of cementing chemical reactions promoted by combination of these materials.

Ordinary Portland cement (OPC) is the main constituent of concrete works as a principal binder for aggregates and intrinsically transmits the brittleness into concrete through the formation of hydration crystals in the cement microstructure. A number of nano cementitious composites were developed in recent years to offset the brittleness with newly discovered nanomaterials and the most prevalent among those is the graphene oxide (GO). The main objective of this PhD research work is to develop nano graphene cementitious composites (NGCC) using low cost, two dimensional (2D) graphene nanoplatelets (GNPs) and one dimensional (1D) graphited carbon nanofibres (GCNFs) with unique conical surface morphology. The GNPs were sourced synthesised in an environmental friendly way via plasma exfoliation whereas, GCNFs were manufactured through catalytic vapour grown method. The project further investigated the effect of these nanomaterials in regulating the distinctive microstructure of cement matrix leading to enhance its mechanical properties. Three different types of high-performance NGCC namely NGCC-Dot, NGCC-Fnt and NGCC-CNF, are developed by activating pristine GNPs (G-Dot), functionalised GNPs (G-Fnt) and graphited nanofibers (G-CNFs) into the cement matrix respectively. It is found through various characterization and experimental techniques that both GNPs and GCNFs regulated the cement microstructure and influenced the mechanical properties of NGCC uniquely. A remarkable increase in the flexural and the tensile strength of newly developed NGCC has been achieved and that could be attributed to the formation of distinctive microstructure regulated by catalytic activation of these nanomaterials. The shape (1D, 2D) and unique morphology of these nanomaterials played a vital role in the mechanism of crystal formation to regulate the cement microstructure. Based on the observations of test results and comprehensive characterization, the possible mechanisms of crystal formation and development of distinctive microstructure of NGCC has been established which has then proceeded to the development of a physical model for NGCC development.

Esta pesquisa trata da estabilização de misturas de agregados reciclados por meio da ativação de seus finos, cujas composições possibilitam a ocorrência de reações químicas de cimentação. Para o desenvolvimento da pesquisa foram utilizados dois tipos de agregados reciclados: um proveniente de resíduo de demolição de natureza cimentícia e outro da indústria de cerâmica vermelha. O uso dos materiais foi feito por meio de dosagens para obtenção de misturas cujas combinações de materiais pudessem, quimicamente, potencializar a ocorrência de hidratação do cimento anidro existente nos finos do agregado reciclado cimentício e de reação pozolânica pela pozolanicidade da cerâmica vermelha. Com isso foram obtidas cinco misturas, compostas pelos agregados reciclados em estudo misturados entre si e com a adição de aglomerantes hidráulicos, sobre as quais foram realizados ensaios em laboratório para verificação da ocorrência das reações químicas esperadas com consequente estabilização das misturas, de modo a influenciar nos respectivos comportamentos mecânicos. Também foi realizada a avaliação de características do empacotamento dos grãos como forma de verificar se o arranjo físico, neste caso, exerce influência significativa na melhora do comportamento mecânico das misturas estudadas. Os resultados obtidos indicaram que, de fato, ocorreram as reações químicas esperadas, comprovadas pelos resultados dos ensaios de termogravimetria e difração de raios x, realizados em três diferentes idades de cura. Verificou-se, também, a melhora no comportamento mecânico das misturas por meio do aumento da resistência à compressão simples e do módulo de resiliência com a evolução da cura, além de baixa deformabilidade aos 91 dias de cura. Com isso foi comprovada a estabilização das misturas em estudo, com a consequente melhora de seus desempenhos, sendo devida, principalmente, à ocorrência das reações químicas de hidratação do cimento anidro e pozolânica. A pesquisa demonstrou a possibilidade de se estabilizar misturas de agregados reciclados cimentícios e de cerâmica vermelha por meio da ocorrência de reações químicas de cimentação promovidas pela combinação destes materiais. / This research deals with the stabilization of mixtures constituted by recycled aggregates through the activation of its fines portions, whose components enable the occurrence of chemical cementation reactions. In order to develop this research, two types of recycled aggregates were used: one from demolition waste with cementitious origin, and the other one from the red ceramic industry. The use of these materials was done through mix designs to obtain mixtures whose combinations of materials could chemically increase the occurrence of hydration of the anhydrous existing in fine portion of the recycled cementitious aggregates, and pozzolanic reactions due to the pozzolanicity of red ceramics. Thus, five mixtures were obtained, and they were composed by the studied recycled aggregates, mixed together and with the addition of hydraulic binders, on which laboratory tests were performed in order to verify the occurrence of the expected chemical reactions with consequent stabilization of the mixtures, in order to influence their mechanical behavior. Furthermore, it was performed the evaluation of packing characteristics of the particles to verify if the physical arrangement, in this case, has any significant influence on improving the mechanical behavior of the mixtures studied. The results obtained indicated that in fact the expected chemical reactions occurred, which was verified by the results from thermogravimetry and X-ray diffraction tests performed at three different times of curing. The improvement of the mixtures mechanical behavior by increasing of their compressive strength and their resilient modulus was also verified as the mixtures were cured, in addition to low deformability at 91 days of curing. Thus, the stabilization of the mixtures studied was confirmed, which was mainly due to the occurrence of chemical hydration reactions of the anhydrous cement and pozzolanic reactions. The study demonstrated the possibility of stabilizing mixtures of recycled aggregates cementitious waste and red ceramic by the occurrence of cementing chemical reactions promoted by combination of these materials.

Submitted by Silvana Teresinha Dornelles Studzinski (sstudzinski) on 2016-12-22T12:03:13Z No. of bitstreams: 1 Josué Claudio Metz_.pdf: 3580473 bytes, checksum: 4bb7f81d4d0a95ef4e39a7d4dffb0599 (MD5) / Made available in DSpace on 2016-12-22T12:03:13Z (GMT). No. of bitstreams: 1 Josué Claudio Metz_.pdf: 3580473 bytes, checksum: 4bb7f81d4d0a95ef4e39a7d4dffb0599 (MD5) Previous issue date: 2016-09-19 / Nenhuma / A concepção de desenvolvimento sustentável tem resultado no aumento de pressões ambientais para a melhoria da eficiência na utilização de recursos, e para a redução das emissões e da geração de resíduos. No processo de fabricação de aço, nas siderúrgicas com fornos elétricos a arco (FEA), ocorre a geração do resíduo sólido denominado pó de aciaria elétrica (PAE). O PAE é constituído por diferentes óxidos metálicos. Contém os elementos químicos cromo (Cr), chumbo (Pb) e cádmio (Cd) e, por isso, é classificado como resíduo classe I – Perigoso pela NBR 10004. Gerado em grandes quantidades diariamente em todo o país, o PAE ainda tem como principal destinação final o aterro industrial. A indústria de papel e celulose, outra atividade de destaque na indústria nacional, gera uma grande quantidade de resíduos em diferentes etapas do processo, entre os quais está o resíduo do forno de cal (RFC), cuja geração está associada a interrupções no funcionamento do forno de cal. A indústria da construção civil, devido a quantidade de matérias-primas consumida e variedade de materiais empregados – cimento, concreto, agregados, cerâmica, entre outros – apresenta-se como alternativa para a reciclagem de resíduos gerados em outros setores da economia. A incorporação do PAE no cimento e concreto produz retardo no tempo de pega em razão da presença de zinco (Zn) no resíduo. Estudos sugerem que em quantidades próximas a 1%, a incorporação de PAE não afeta de forma significativa as propriedades do cimento. O objetivo deste trabalho foi avaliar a influência do uso combinado de PAE e RFC no processo de endurecimento e evolução da hidratação de pastas de cimento. Para tanto, foi realizada a caracterização dos resíduos através dos ensaios de distribuição granulométrica, perda ao fogo, massa específica, área superficial específica, análise química elementar, difração de raios X com refinamento por Rietveld e microscopia eletrônica de varredura. A influência dos resíduos nas pastas de cimento foi avaliada através do ensaio de tempo de pega de acordo com a NBR NM 65 (ABNT, 2003b) e evolução da temperatura semi-adiabática das pastas em estado fresco, além de DRX, com refinamento por Rietveld, e microscopia eletrônica de varredura nas pastas de cimento com diferentes teores de substituição de resíduos (REF, 1%, 2%, 3%, 5% e 10%) em diferentes idades (1, 4 e 7 dias). Os resultados de tempo de pega e evolução da temperatura semi-adiabática indicaram a influência do PAE na hidratação das pastas de cimento. Nas pastas de cimento com substituição de 1% de PAE combinado ou não com RFC, não foram verificados retardos significativos no tempo de pega, demonstrando o potencial do uso de PAE e do RFC na produção de artefatos de cimento. / The sustainable development conception has resulted in increased environmental pressures to improve the efficient use of resources and reduction of emissions and waste generation. In the steelmaking process through electric arc furnaces (EAF), dust generation occurs which is called electric arc furnace dust (EAFD). EAFD is composed by different metal oxides. Some common elements those constitute this dust is chromium, lead and cadmium, and therefore, waste is classified as class I – hazardous by NBR 10004. EAFD has been generated in large quantities every day across the country and it still has mainly landfilled. The pulp and paper industry, another important activity in the domestic industry, generates a lot of waste in different stages of the process, among which is the lime kiln waste (LKW), whose generation is associated with disruptions in the lime oven. Due to expressive amount of raw materials consumed in civil construction industry and also the variety of products available - cement, concrete, aggregates, ceramics, among others - this seems to be an alternative for waste recycling generated in other sectors. The incorporation of EAFD in the cement and concrete produces delayed setting time due to the presence of zinc (Zn) in the waste. Studies suggest that in amounts up to 1%, EAFD incorporation does not affect significantly cement properties. The aim of this work was to evaluate the influence of the combined use of EAFD and LKW in the process of hardening and evolution of the cement pastes hydration. Therefore, were evaluated the characterization of the waste performed through the grain size distribution, loss on ignition, specific gravity, specific surface area, elemental chemical analysis, pH, X ray powder diffraction with refinement by Rietveld and scanning electron microscopy.. The influence of the waste on the cement pastes was evaluated through the setting time tests in accordance with the NBR NM 65 (ABNT, 2003b) and evolution of semi-adiabatic temperature in fresh conditions, XRD with refinement by Rietveld, and SEM in cement pastes with different levels of waste substitution (REF, 1%, 2%, 3%, 5% e 10%) at different ages (1, 4 and 7 days). The setting time results and evolution of semi-adiabatic temperature indicated an increase in the setting time with the increase of the EAFD in cement pastes. In cement pastes with replacement of 1% EAFD combined or not with LKW, significant delays were not verified in the setting time, demonstrating the potential use of EAFD in the production of cement artifacts.

The eco-friendly alternatives use is increasing momentum in a conscious effort towards sustainability. In this regards, the relevance and the economic value of using copper slag as a concrete aggregate are explored in this study in order to contribute towards metallurgical waste recycling. Emphasis is placed on the evaluation of the concretes strengthening prepared with copper slag contents and produced under four curing methods: water immersion, water spraying, plastic sheet covering and air-drying. In each curing case excluding for water immersion, was duplicated in indoors (i.e. in the laboratory) and outdoor exposure (so was prone to varying environmental conditions). This was specifically aimed at capturing the effects of tropical weather conditions typical of the Lualaba province in the Democratic Republic of Congo. The control mix was designed to reach 25 MPa of compressive strength. Copper slag was successively incorporated as sand replacement at the following mass fractions: 20 %, 40 % and 60 %. Freshly mixed concrete samples were evaluated for workability. Cube specimens were cast accordingly, cured for 28 days and then tested for density and compressive strength. Results indicated an increase in strength up to 20 % of replacement rate for all the curing methods. Further additions resulted in reduction in the strength, but the rate of reduction depended on curing conditions. The increase in strength was mainly credited to the physical properties of copper slag that could have contributed to the cohesion of the concrete matrix. It has been found that appropriate ways of curing can still achieve greater results than that of the control mix since 80 % of humidity is ensure. The two-way ANOVA test performed on the 28-days compressive strength values confirmed the significant influence of the curing methods, of copper slag content and the interaction between them. It has been found that considerable influence is attributed to copper slag content and that warm environmental conditions further extend the concrete strengthening. / College of Engineering, Science and Technology / M. Tech. (Chemical Engineering)

Master’s thesis examines the effect of the shrinkage reducing additives on rheological properties of high-strength concrete. The first part is focused on high-strength concrete in terms of their composition and properties. The second part contains a detailed analysis of the cementitious composites shrinkage problems. Total shrinkage is divided into individual elementary shrinkages. For each of them there is a detailed description of causes and factors that affect their sizes. The next part describes the basic additives used to reduce the shrinkage of cementitious composites. The experimental part is focused on verifying the effectiveness of the shrinkage reducing additives during preparation of high-strength concrete. Usage of shrinkage drains for relative strain measurement enables to determine the process of shrinkage immediately after placing the concrete in the form and to obtain the overall curve of the hight-strength concrete volume changes during its setting and hardening. At the end of the thesis, there are overall analysis and summary of the results of the performed experiments.

In the construction industry, concrete is the most common material, because of its good properties such as compressive strength and endurance. Concrete is a composition of several different materials where one of the main components is cement. When the hydration process starts, large amount of heat is generated. This leads to temperature rise within the structure. The heat development that takes place can become critical for massive structures such as dams and power plants, where natural cooling is not sufficient. This in combination with internal and external restraint resulting in tensions causing cracks in the structure. By controlling the temperature development, one can reduce the risk of cracking in massive structures. The controlling is divided into pre-cooling and post-cooling. Reduction of the risk for thermal cracking can be done in different ways. Parts of the cement in the concrete can be replaced by a pozzolan material such as silica fume, blast furnace slag or fly ash. Another method is to increase the size of the aggregates which makes it possible to reduce the cement content with remained strength. Cooling the aggregates or use of ice can also be used as a pre-cooling methods. The most common post-cooling method is the installation of cooling pipes. Pipes are installed between the reinforcement bars, in which one then pump through with cold water. This thesis aims at practicing the methods examined by Lagundžija &amp; Thiam (2017). Focusing on those results that proved to be most effective, i.e. the combination of fly ash, ice and large aggregates. The results retrieved during the tests shows a significant increase in the compressive strength when using a combination of fly ash, ice and large aggregates. This gives us the opportunity to reduce the initial cement content. Reducing the cement content is the most effective factor regarding the heat development. When replacing amounts of the water with ice, it can be seen that the initial casting temperature was reduced. Further studies can be done to find the right amount of reduction of the cement that can be done while maintaining the required compressive strength. / Inom byggbranschen är betong det mest förekommande materialet, detta tack vare dess goda egenskaper, som till exempel tryckhållfasthet och uthållighet. Betongen utgörs av flera olika beståndsdelar där den centrala komponenten är cement. När cementets hydratationsprocess startar utvecklas en markant värmeutveckling. Detta leder till temperaturhöjningar inuti den nygjutna konstruktionen. Värmeutvecklingen kan bli kritisk för grövre konstruktioner, som till exempel dammar och kraftverk, där naturlig avkylning inte är tillräcklig. Detta i kombination med att inre och yttre tvång resulterar i dragspänningar som orsakar sprickor i konstruktionen. Genom att styra temperaturutvecklingen kan man minska risken för sprickbildning i massiva konstruktioner. Styrningen delas in i förberedande kylning och efterkylning. Reduktion av risken för termisk sprickbildning kan ske på olika sätt. Delar av cementen i betongen kan ersättas med ett puzzolant material som till exempel silikatstoft, masugnsslagg eller flygaska. En annan metod är att öka ballaststorleken vilket gör det möjligt att minska cementhalten med kvarvarande hållfasthet. Man kan även kyla ballasten alternativt blanda in is i mixen för att sänka den initiala temperaturen. Den mest förekommande efterkylningsmetoden är installation av kylrör. Det monteras in rör mellan armeringsjärnen, vilket man sedan pumpar kallt vatten igenom. Denna uppsats syftar på att praktiskt tillämpa de metoder som undersöktes av Lagundžija &amp; Thiam (2017). Fokus på de resultat som visade sig vara mest effektiva, dvs kombinationen av flygaska, is och grov ballast. Resultaten som uppnåddes under de tester som utfördes visar en markant ökning i tryckhållfastheten vid användning av kombinationen med flygaska, is och grov ballast. Detta ger oss utrymmet att reducera den initiala cementhalten som används. Att minska cementinnehållet är den faktor som ger störst effekt gällande värmeutvecklingen. Fortsatta studier kan göras för att hitta rätt mängd reduktion av cementet som kan göras samtidigt som anvisad tryckhållfasthet bibehålls.

[pt] O presente estudo busca definir uma relação de mistura estável utilizando aditivos poliméricos à base de álcool polivinílico (PVOH) para controlar a perda de filtrado, antiespumante e dispersante, caracterizando a influência de cada adição na cinética de hidratação, propriedades mecânicas, físicas e reologia da mistura. Além disso, foi caracterizado o comportamento das pastas de cimento em condições de cura que simulam a situação do poço até 6100 m de profundidade, seguindo as recomendações da API, e o comportamento do material nos estados in situ, utilizando pressões confinantes para realizar os ensaios de compressão. Por fim, propôs-se a inclusão de microfibras de álcool polivinílico (PVA) para melhorar o desempenho mecânico das pastas cimentícias, avaliando diferentes tipos de carregamento e definindo os impactos da adição de fibras na viscosidade e tixotropia das misturas. Verificou-se que o uso de PVOH como aditivo de perda de filtrado não influencia na cinética de hidratação para concentrações de até 0,4% em peso de cimento, mas à medida que a quantidade de PVOH é aumentada na mistura, o processo de hidratação da pasta de cimento pode ser modificado por causa do mecanismo de absorção do PVOH. Além disso, novas fases de produtos de hidratação aparecem com o aumento da temperatura e pressão de cura: dellaite, hydroxyellestadite e alpha-C2SH. A última fase (alpha-C2SH) está relacionada à perda de capacidade de resistência das amostras curadas a 149°C, simulando o caso do poço de petróleo de 6100 m de profundidade. Para os ensaios triaxiais, a pressão de confinamento conferiu às amostras um comportamento diferente do caso uniaxial, implicando em uma considerável melhora da plasticidade no comportamento tensão-deformação. Embora se observe algum reforço por atrito devido a tensões de cisalhamento no plano das fissuras, o efeito mais importante do confinamento é suportar a deformação dúctil, mesmo para o caso da pasta de cimento reforçada com fibra de PVA. Finalmente, o estudo mostrou que as fibras de PVA conferem um leve aumento da viscosidade da pasta de cimento, uma fase plástica prolongada aparentemente sem perda de capacidade de carga em testes triaxiais e uma capacidade aprimorada de absorver energia ao avaliar cargas de tração e cisalhamento. / [en] The present study seeks to define a stable mixing ratio using powder Polyvinyl Alcohol (PVOH) based polymeric additives to control the loss of filtrate, defoamer, and dispersant, characterizing the influence of each addition on hydration kinetics, mechanical and physical properties, and rheology of the mix. The behavior of cement pastes under curing conditions that simulate the wellbore situation up to 6100 m depth was also evaluated, following API recommendations. Moreover, the behavior of the material under in situ states, using confining pressures to perform the compression tests, was characterized. Finally, the inclusion of Polyvinyl Alcohol (PVA) microfibers is proposed to improve the mechanical performance of cement pastes, evaluating different types of loading and defining the impacts of the fiber addition on the viscosity and thixotropy of the mixtures. It was found that the use of PVOH as a fluid loss additive does not influence hydration kinetics for concentrations up to 0.4% by weight of cement, but as the amount of PVOH is increased in the mixture, the hydration process of the cement paste may be modified because of the PVOH absorptive mechanism. Moreover, new hydration products phases appear with increasing curing temperature and pressure: dellaite, hydroxyellestadite, and alpha-C2SH. The last phase (alpha-C2SH) is related to the loss of strength capacity of the samples cured at 149°C, simulating a 6100 m depth wellbore. For the triaxial tests, the confining pressure gave the samples a behavior markedly different from the uniaxial case, implying a considerable improvement in the plasticity of the stress-strain behavior. Although some frictional reinforcement is observed due to shear stresses in the cracks surface, the most important effect of confinement is to withstand ductile deformation, even in the case of PVA fiber-reinforced cement paste. Finally, the study has shown that PVA fibers impart a slight viscosifying effect on the cement slurry, a prolonged plastic phase with apparently no loss of load-carrying capacity in triaxial tests, and an improved ability to absorb energy when evaluating tensile and shear loads.