The thesis is focused on the study of electric and dielectric properties of thin film organic materials that can be used as an active layer of photovoltaic cells. Primarily were studied the properties of the layers on the glass substrates, which consist of a thin active layer of phthalocyanines. On the samples were first measured current-voltage characteristics (in the dark and during the exposure) and the basic parameters of the photovoltaic conversion were determined. Finally were measured frequency dependencies (impedance spectra, in the dark and during the exposure) and the parameters of a model of the structure with organic semiconductor were determined. The obtained results will be used to optimize the properties of photovoltaic cells.

Porous metal oxides formed by supercritical carbon dioxide (SCCO2) treatments at low temperature were used for displays, solar cells, and light emitting diodes (LEDs) applications. The SCCO2 fluid, also known as green solvents, exhibits low viscosity, low surface tension and high diffusivity as gases, and high density and solubility same with liquids. In this thesis, we successfully fabricated porous antimony-doped tin oxide (ATO) and porous indium tin oxide (ITO) by the SCCO2 treatments. In addition, the treatment can also be used to improve the work function and surface energy of ITO anode of an organic LED (OLED). The performance of the OLEDs was drastically enhanced in comparison with that of the devices without any ITO surface treatments. First, the porous ATO films were formed by the SCCO2 treatment for absorption of silver molecules in silver electro deposition devices. The porosity, resistivity and average optical transmittance of the porous ATO film in visible wavelength were 43.1%, 3 £[-cm and 90.4%, respectively. For the silver electro deposition devices with the porous ATO film, the transmittance contrast ratio of larger than 12 in visible spectrum was obtained at an operating voltage of 1.5 V. Furthermore, for the 0.25 cm2 device, the switching time of 4.5 seconds was achieved by applying a square-wave voltage ranging from 1.5 to -0.2 V between the electrodes. On the other hand, the porous ITO with low refractive index was prepared by SCCO2/IPA treatment on gel-coated ITO thin films. The high refractive index of the ITO film was achieved by long-throw radio-frequency magnetron sputtering technique at room temperature. The index contrast (£Gn) was higher than 0.6 between porous ITO and sputtered ITO films. The large £Gn is useful for fabricating conductive anti-reflection (AR) and high reflection (HR) structures using the porous ITO on sputtered ITO bilayers. The weighted average reflectance and transmittance of 4.3% and 83.1% were achieved for the double-layer ITO AR electrode with a sheet resistance of 1.1 K£[/¡E. For HR structures, the reflectance and sheet resistance were 87.9% and 35 £[/¡E with 4 periods ITO bilayers. Finally, the SCCO2 treatments with strong oxidizer H2O2 were proposed to modify surface property of ITO anode of a fluorescent OLED. The highest work function and surface energy of 5.5 eV and 74.8 mJ/m2 was achieved by the SCCO2/H2O2 treatment. For the OLED with 15 min SCCO2 treatment at 4000 psi, the turn-on voltage and maximum power efficiency of 6.5 V and 1.94 lm/W were obtained. The power efficiency was 19.3% and 33.8% higher than those of the OLEDs with oxygen plasma treated and as-cleaned ITO anodes.

In this work, well-defined and stable thin films based on polythiophene and its derivative, are employed as the hole-injection contact of organic light-emitting diodes (OLED). The polymer films are obtained by the electropolymerization or the electrochemical doping/dedoping of a spin-coated layer. Their electrical properties and energetics are tailored by electrochemical adjustment of their doping levels in order to improve the hole-injection from the anode as well as the performance of small molecular OLEDs. By using dimeric thiophene and optimizing the electrodeposition parameters, a thin polybithiophene (PbT) layer is fabricated with well-defined morphology and a high degree of smoothness by electro-polymerization. The introduction of the semiconducting PbT contact layer improves remarkably the hole injection between ITO anode and the hole- transport layer (NPB) due to its favourable energetic feature (HOMO level of 5.1 eV). The vapor-deposited NPB/Alq3 bilayer OLEDs with a thin PbT interlayer, show a remarkable reduction of the operating voltage as well as enhanced luminous efficiency compared to the devices without PbT. Investigations have also been made on the influence of PbT thickness on the efficiency and I-V feature as well as device stability of the OLED. It is demonstrated that the use of an electropolymerization step into the production of vapor deposited molecular OLED is a viable approach to obtain high performance OLEDs. The study on the PbT has been extended to poly(3,4-ethylenedioxythiophene) (PEDT) and the highly homogenous poly(styrenesulfonate) (PSS) doped PEDT layer from a spin-coating process has been applied. The doping level of PEDT:PSS was adjusted quantitatively by an electrochemical doping/dedoping process using a p-tuoluenesulfonic acid containing solution, and the redox mechanism was elucidated. The higher oxidation state can remain stable in the dry state. The work function of PEDT:PSS increases with the doping level after adjusting at an electrode potential higher than the value of the electrochemical equilibrium potential (Eeq) of an untreated film. This leads to a further reduction of the hole-injection barrier at the contact of the polymeric anode/hole transport layer and an ideal ohmic behavoir is almost achieved at the anode/NPB interface for a PEDT:PSS anode with very high doping level. Molecular Alq3-based OLEDs were fabricated using the electrochemically treated PEDT:PSS/ITO anode, and the device performance is shown to depend on the doping level of polymeric anode. The devices on the polymer anode with a higher Eeq than that for the unmodified anode, show a reduction of operating voltage as well as a remarkable enhancement of the luminance. Furthermore, it is found that the operating stability of such devices is also improved remarkably. This originates from the removal of mobile ions such as sodium ions inside the PEDT:PSS by electrochemical treatment as well as the planarization of the ITO surface by the polymer film. By utilizing an Al/LiF cathode with an enhanced electron injection and together with a high Eeq- anode, a balanced injection and recombination of hole and electron is achieved. It leads to a further reduction of the operating voltage and to a drastic improvement of EL efficiency of the device as high as 5.0 cd/A. The results demonstrate unambiguously that the electrochemical treatment of a cast polymer anode is an effective method to improve and optimize the performance of OLEDs. The method can be extended to other polythiophene systems and other conjugated polymers in the fabrication of the OLEDs as well as organic transistors and solar cells.

A numerical model and results for the quantitative simulation of multilayer organic light emitting diode (OLED) and organic solar cell (OSC) are presented. In the model, effects like bipolar charge carrier drift and diffusion with field-dependent mobilities, trapping, dopants, indirect and direct bimolecular recombination, singlet Frenkel exciton diffusion, normal decay and quenching effects are taken into account. For an adequate description of multilayer devices with energetic barriers at interfaces between two adjacent organic layers, thermally assisted charge carrier hopping through the interface, interface recombination, and formation of interface charge transfer (CT) states have been introduced in the model. For the simulation of OSC, the generation of carrier pairs in the mixed layer or at the interface is additionally implemented. The light absorption profile is calculated from optical simulations and used as an input for the electrical simulation. The model is based on three elements: the Poisson equation, the rate equations for charge carriers and the rate equations for singlet Frenkel excitons. These equations are simultaeously solved by spatial and temporal discretisation using the appropriate boundary conditions and electrical parameters. The solution is found when a steady state is reached, as indicated by a constant value of current density. The simulation provides a detailed look into the distribution of electric field and concentration of free and trapped carriers at a particular applied voltage. For organic light emitting diodes, the numerical model helps to analyze the problems of different structures and provides deeper insight into the relevant physical mechanisms involved in device operation. Moreover, it is possible to identify technological problems for certain sets of devices. For instance, we could show that ? in contrast to literature reports - the contact between Alq3 and LiF/Al did not show ohmic behaviour for the series of devices. The role of an additional organic blocking layer between HTL and EML was presented. The explanation for the higher creation efficiency for singlet excitons in the three-layer structure is found in the separation of free holes and electrons accumulating close to the internal interface 1-Naphdata/Alq3. The numerical calculation has demonstrated the importance of controlled doping of the organic materials, which is a way to obtain efficient light emitting diodes with low operating voltage. The experimental results has been reproduced by numerical simulation for a series of OLEDs with different thicknesses of the hole transport layer and emitting layer and for doped emitting layers. The advantages and drawbacks of solar cells based on flat heterojunctions and bulk heterojunctions are analyzed. From the simulations, it can be understood why bulk-heterojunctions typically yield higher photocurrents while flat heterojunctions typically feature higher fill factors. In p-i-n ?structures, p and n are doped wide gap materials and i is a photoactive donor-acceptor blend layer using, e.g,. zinc phthalocyanine as a donor and C60 as an acceptor component. It is found that by introducing trap states, the simulation is able to reproduce the linear dependence of short circuit currents on the light intensity. The apparent light-induced shunt resistance often observed in organic solar cells can also be explained by losses due to trapping and indirect recombination of photogenerated carriers, which we consider a crucial point of our work. However, these two effects, the linear scaling of the photocurrent with light intensity and the apparent photoshunt, could also be reproduced when field-dependent geminate recombination is assumed to play a dominant role. First results that show a temperature independent short circuit photocurrent favour the model based on trap-mediated indirect recombination.

The organic light-emitting diode (OLED) technology is emerging to be the future technology of choice for thin, flexible and efficient display and lighting panels and is a potential competitor for the existing flat panel display technologies, like liquid crystal display (LCD) and plasma display panel (PDP). OLEDs display is already making their way from both lab and industry research to display market and the pace of development of laboratory OLED design into a commercial product is very impressive. The OLED display offers several advantages over other display technologies, such as low power consumption, easy fabrication, high brightness & resolution, light weight, compact, flexible, wide viewing angle and fast response. However, OLED display is still in amateur stage in terms of their cost and lifetime. Despite of the abovementioned advantages of OLEDs, there still several issues that need to be addressed to explore the full potential of this display technology. The development of materials with high photoluminescence quantum yield (PLQY), thermal and electrochemical stability, packaging, and light extracting technology are some of the major issues. Among the emitting materials, the achievement of robust blue emitting material with high PLQY and color purity is still a challenge due to its intrinsic wide bandgap and complex device configuration. The work presented in this thesis is devoted to the development of robust blue emitting materials based on fluoranthene derivatives. Fluoranthene unit has been chosen due to its blue emission, high photoluminescence quantum yield, thermal and electrochemical stability. The thesis is organized in six chapters, and a brief discussion on the content of individual chapters is provided below. Chapter 1 provides a short description of evolution of display technology and history of OLEDs. The generation wise development of emitting materials for white OLED is concisely illustrated. The working principle, function of individual layer and factors governing external quantum efficiency of OLED device are elaborated. Finally, the important prerequisite properties of blue emitting materials for OLED application are outlined. Chapter 2 reports the design and synthesis of symmetrically and asymmetrically functionalized fluoranthene-based materials to address the issue of PL quenching in solid state, and subsequently for application in non-doped electoluminescent devices. A detailed experimental and theoretical study has been performed to understand the effect of symmetric and asymmetric functional groups on optical, thermal and electrochemical properties. The fluoranthene derivatives reported in this chapter exibited deep blue emission with high PLQY in both solution and solid state. The vacuum deposited non- doped OLED devices were fabricated and characterized utilizing these materials as emitting layer. Chapter 3 describes the rationale design of thermally stable fluoranthene derivatives as electron transport materials for OLEDs. The two derivatives investigated in this chapter comprised of two fluoranthene units linked by diphenylsulfane and dibenzothiophene linkage. The effect of rigidity provided by ring closure in molecular structure on the physical and charge transport properties has been investigated. Such materials are urgently demanded for better performance and durability of displays. In an extension to chapter 3, fluoranthene based dual functional materials possessing blue light emission and electron transport characteristics are described in Chapter 4. The application of these materials in bilayer blue OLED device successfully demonstrated. The development of such dual functional materials is an important step to not just simplify the OLED device architecture; but also has the potential to reduce the manufacturing and processing cost significantly. Chapter 5 reports the synthesis of the star-shaped fluoranthene-triazine based blue photoluminescent materials for solution processable OLEDs. The effect of chalcogen on the photophysical and electroluminescence properties has been investigated. The main advantage of such solution processable materials over small molecules is to overcome the power consuming vacuum thermal evaporation technique for deposition. Chapter 6 describes the design and synthesis of a new blue emitting material comprising of a donor moiety and an acceptor unit to observe thermally activated delayed fluorescence (TADF). However, photophysical studies did not show any sign of delayed fluorescence in this molecule. Nevertheless, a deep blue electroluminescence is achieved using a multilayer OLED device configuration.

Les diodes électroluminescentes organiques (OLED) ont une durée de vie limitée. Cette limitation est notamment due à la présence d'impuretés dans le matériau électroluminescent. Ces impuretés proviennent principalement des électrodes. Nous pensons que l'ajout de couches de matériaux entre les électrodes et le matériau électroluminescent peut retarder l'arrivée des impuretés. Cette couche ajoutée doit avoir plusieurs caractéristiques dont principalement :être conductrice, ne pas absorber la lumière, être facilement mise en oeuvre et être d'une grande pureté. Nous pensons que des matériaux de type discotique possédant une mésophase aux températures d'utilisation de la OLED peuvent remplir ce cahier des charges.<p>Nous avons choisi d'étudier les composés discotiques à base de triphénylène, car celui-ci n'absorbe pas dans le visible. Nous avons tout d'abord étudié les 2,3,6,7,10,11-Hexa-(alkylthio)triphénylènes (HATT). Les HATT possèdent déjà les propriétés physiques que nous recherchons à l'exception des propriétés thermotropes. Nous avons donc étudié la possibilité de modifier celles-ci.<p>La synthèse de plusieurs HATT possédant six chaînes alkylsulfanyles identiques n'a pas donné les résultats attendus du point de vue des propriétés thermotropes. Nous avons alors synthétisé des molécules possédant plusieurs chaînes alkylsulfanyles différentes. Après différents essais, nous avons trouvé un mélange de molécules possédant plusieurs chaînes latérales différentes ayant les propriétés physiques recherchées. Mais ce matériau est composé d'un grand nombre de molécules et sa purification est difficile. Les techniques classiques de purification des composés organiques ne donnant pas une pureté suffisante, ou étant inapplicables sur une mésophase cristal liquide à température ambiante, nous avons donc recherché d'autres techniques de purification ou d'obtention des propriétés thermotropes désirées.<p> Nous avons étudié la purification par raffinage de zone des matériaux à l'aide d'une impureté que nous avons ajoutée et suivie au cours des manipulations. Le raffinage de zone montre une bonne purification lors de l'utilisation d'une transition de phase entre une phase cristalline et une phase liquide. Par contre, lors de l'utilisation d'une transition impliquant une mésophase (cristal liquide ou cristal plastique), une faible (ou une absence de) purification est observée. Ces deux dernières études ont été faites sur des 2,3,6,7,10,11-Hexa(alkyloxy)triphénylènes (HAOT) que nous avons synthétisés et purifiés au préalable. <p>Les gels de silice fonctionnalisés que nous avons utilisés montrent une purification des cations métalliques durs et, dans une moindre mesure, des cations métalliques intermédiaires dans le concept dur-mou. Le phosphore, seul élément non-métallique que nous ayons étudié, est l'élément dont la baisse de concentration est la moins efficace.<p>La seconde approche pour obtenir des mélanges possédant une mésophase cristal liquide à température ambiante est la formation de mélanges de molécules synthétisées et purifiées isolément. Parmi les mélanges de molécules que nous avons effectués, nous avons pu observer une plage de concentration de mélanges ternaires qui possède les propriétés thermotropes recherchées.<p>Nous avons donc obtenu un matériau cristal liquide à température ambiante grâce à un mélange de molécules. Le matériau ainsi formé absorbe peu dans le visible, possède potentiellement une bonne mobilité des porteurs de charges électriques, est facilement obtenu à une pureté suffisante. Ce mélange de molécules possède donc les propriétés que nous recherchons pour être utilisé comme couche de matériau ajoutée aux OLED.<p> / Doctorat en sciences, Spécialisation chimie / info:eu-repo/semantics/nonPublished

Optofluidics is a new branch within photonics which attempts to unify concepts from optics and microfluidics. Unification of photonics and microfluidics enable us to carry out analysis of fluids through highly sensitive optical sensing device. These optical sensing devices are contained within a microchip, wherein light is made to pass through analyte (fluids of few nanoliters). The interaction between light and fluid gives rise to highly sensitive diagnostic systems. In this work the fabrication and performance characterization of a fluorescent green OLED for optofluidic applications is presented. The effect of thickness variation of hole injection (CuPc) and hole blocking (BCP) layers on the performance of fluorescent green organic light emitting diodes (OLEDs) have been studied. Even though these two organic layers have opposite functions, yet there is a particular combination of their thicknesses when they function in conjunction and luminous efficiency and power efficiency are maximized. The optimum thickness of CuPc layer, used as hole injection layer and BCP used as hole blocking layer were found to be 18 nm and 10 nm respectively. It is with this delicate adjustment of thicknesses, charge balancing was achieved and luminous efficiency and power efficiency were optimized. Such OLEDs with higher luminance can be monolithically integrated with other optical and fluidic components on a common substrate and can function as monolithically integrated internal source of light in optofluidic sensors. In this work the analysis of a fully integrated optofluidic lab-on-a-chip sensor for refractive index and absorbance based sensing using fluorescent green organic light emitting diode (OLED) as a light source is also presented. This device consists of collinear input and output waveguides which are separated by a microfluidic channel. When light is passed through the analyte contained in the fluidic gap an optical power loss due to absorption of light takes place. Apart from absorption a mode-mismatch between collinear input and output waveguide also occurs. The degree of mode-mismatch, quantum of optical power loss due to absorption of light by the fluid forms the basis of our analysis. Detection of minutest change in refractive index and changes in concentration of species contained in the analyte is indicative of sensitivity. Various parameters which influence the sensitivity of the sensor are mode spot size, refractive index of the fluid, molar concentration of the species contained in the analyte, width of the fluidic gap, waveguide geometry. By correlating various parameters, an optimal fluidic gap distance corresponding to a particular mode spot size to achieve the best sensitivity for refractive index based sensing and absorbance based sensing have been determined.

This dissertation deals with two major topics that involve spectroscopic studies of (a) divalent group 10 metals and (b) silver(I)-phosphine complexes. The scope of the work involved the delineation of the electronic structure of these complexes in different environments and their use in electronic devices. The first topic is a look at the luminescence of tetrahedral silver(I)-phosphine complexes. Broad unstructured emissions with large Stokes shifts were found for these complexes. Computational analysis of the singlet and triplet state geometries suggests that this emission is due to a Jahn-Teller type distortion. The second topic represents the major thrust of this research, which is an investigation into the electronic structure of M(diimine)X2 (M= Pt(II), Pd(II), or Ni(II); X = dichloro, or dithiolate ligands) complexes and their interactions with an electron acceptor or Lewis acid. Chapter 3 assesses the use of some of these complexes in dye sensitized solar cells (DSSCs); it is shown that these complexes may lead to a viable alternative to the more expensive ruthenium-based dyes that are being implemented now. Chapter 4 is an investigation into donor/acceptor pairs involving this class of complexes, which serves as a feasibility test for the use of these complexes in organic photo-voltaics (OPVs) and thin-film field-effect transistors (OTFTs). The mixing of a donor Pt molecule with an electron deficient nitrofluorenone gives rise to new absorption bands in the NIR region. Computational studies of one of the solids suggest that these complexes may have metallic behavior. Chapter 5 demonstrates association in solution, previously unobserved, for Pt(diimine)Cl2 complexes. This chapter is an investigation into the effects of the association mode for this class of complexes on the absorption and emission properties. One of the complexes was used as the emitter in organic light emitting diodes (OLEDs). The results of this study show that these complexes have tunable absorption and emission energies that are concentration dependant. The concentration dependence of the absorption and emission energies is utilized in the OLED device where association enhances the performance.

A numerical model and results for the quantitative simulation of multilayer organic light emitting diode (OLED) and organic solar cell (OSC) are presented. In the model, effects like bipolar charge carrier drift and diffusion with field-dependent mobilities, trapping, dopants, indirect and direct bimolecular recombination, singlet Frenkel exciton diffusion, normal decay and quenching effects are taken into account. For an adequate description of multilayer devices with energetic barriers at interfaces between two adjacent organic layers, thermally assisted charge carrier hopping through the interface, interface recombination, and formation of interface charge transfer (CT) states have been introduced in the model. For the simulation of OSC, the generation of carrier pairs in the mixed layer or at the interface is additionally implemented. The light absorption profile is calculated from optical simulations and used as an input for the electrical simulation. The model is based on three elements: the Poisson equation, the rate equations for charge carriers and the rate equations for singlet Frenkel excitons. These equations are simultaeously solved by spatial and temporal discretisation using the appropriate boundary conditions and electrical parameters. The solution is found when a steady state is reached, as indicated by a constant value of current density. The simulation provides a detailed look into the distribution of electric field and concentration of free and trapped carriers at a particular applied voltage. For organic light emitting diodes, the numerical model helps to analyze the problems of different structures and provides deeper insight into the relevant physical mechanisms involved in device operation. Moreover, it is possible to identify technological problems for certain sets of devices. For instance, we could show that ? in contrast to literature reports - the contact between Alq3 and LiF/Al did not show ohmic behaviour for the series of devices. The role of an additional organic blocking layer between HTL and EML was presented. The explanation for the higher creation efficiency for singlet excitons in the three-layer structure is found in the separation of free holes and electrons accumulating close to the internal interface 1-Naphdata/Alq3. The numerical calculation has demonstrated the importance of controlled doping of the organic materials, which is a way to obtain efficient light emitting diodes with low operating voltage. The experimental results has been reproduced by numerical simulation for a series of OLEDs with different thicknesses of the hole transport layer and emitting layer and for doped emitting layers. The advantages and drawbacks of solar cells based on flat heterojunctions and bulk heterojunctions are analyzed. From the simulations, it can be understood why bulk-heterojunctions typically yield higher photocurrents while flat heterojunctions typically feature higher fill factors. In p-i-n ?structures, p and n are doped wide gap materials and i is a photoactive donor-acceptor blend layer using, e.g,. zinc phthalocyanine as a donor and C60 as an acceptor component. It is found that by introducing trap states, the simulation is able to reproduce the linear dependence of short circuit currents on the light intensity. The apparent light-induced shunt resistance often observed in organic solar cells can also be explained by losses due to trapping and indirect recombination of photogenerated carriers, which we consider a crucial point of our work. However, these two effects, the linear scaling of the photocurrent with light intensity and the apparent photoshunt, could also be reproduced when field-dependent geminate recombination is assumed to play a dominant role. First results that show a temperature independent short circuit photocurrent favour the model based on trap-mediated indirect recombination.

This thesis deals with the design of LED matrix array contains 150 LEDs. In the first part, the thesis identifies source of light like OLED and LED and provide an overview of their lifetime, reliability and basic principle of design systems with LEDs. The thesis then describe design of LED matrix array, deals with power supply of this LED array and with cooling of LED. Finally the thesis describes a software for contol of LED matrix array.