This work focused on the fabrication and electrical characterization of electronic devices and the applications include the n-channel organic field-effect transistors (OFETs), organic complementary circuits, and the germanium nanowire transistors. In organic devices, carbonyl-functionalized [alpha],[omega]-diperfluorohexyl quaterthiophenes (DFHCO-4T) and N,N' --bis(n-octyl)-dicyanoperylene-3,4:9,10-bis(dicarboximide) (PDI-8CN2) are used as n-type semiconductors. The effect of dielectric/electrode surface treatment on the response of bottom-contact devices was also examined to maximize the device performance. Some of innovative techniques that employ the conducting polymer, poly(3,4-ethylenedioxythiophene) / poly(styrene sulfonate) (PEDOT/PSS) for the fabrication of OFETs, were compared and investigated. The device performance and the fabrication yield were also considered. Organic complementary ring oscillators and D flip-flops were demonstrated with PDI-8CN2 and pentacene as the n-type and ptype material, respectively. Both circuits recorded the highest speed that any organic transistor-based complementary circuit has achieved to date. The speed of these complementary circuits will be enhanced by increasing the mobility of n-channel further as well as reducing channel lengths and overlap capacitances between the source/drain electrodes and the gate. The semiconductors should be solution processible to be compatible with the inexpensive fabrication techniques envisioned for printed electronic circuits. PDI-8CN2 was used for solution-processed n-channel OFETs and the various parameters are compared for the optimization of devices. Utilizing optimized process parameters and surface treatments for solution-deposited PDI-8CN2 OFETs, we have successfully shown the first fabrication of complementary organic ring oscillators and Dflip flops by the micro-injection of the solution of both p-type and n-type materials in air. One of the potential platforms for low cost fabrication on flexible substrates is the use of inorganic semiconductor nanowires. Accordingly, the germanium nanowire FETs were fabricated and characterized. Conductivity enhanced PEDOT/PSS was employed as the electrode material for nanowire transistors to improve the electrical contacts to the source and drain. / text

Supramolecular electronics aims to construct and investigate the optoelectronic properties of tailored supramolecular nanoarchitectures. The aim of this thesis is to get control over the organization of organic molecular systems and correlate their structure with the electrical properties, with particular attention at the nanoscale properties. The exploited strategies require a focused molecular design, the balancing of intermolecular and interfacial interactions, a control on the kinetics of the processes and possibly the exploitation of external forces. The presented results showed that understanding the local properties of a material on a nanoscale basis is a huge fundamental challenge to bring solutions to both scientific and technological issues, since in electronic devices the performances are strongly dependent on the order at the supramolecular level.

Diese Arbeit beschäftigt sich mit der Untersuchung der Langzeitstabilität organischer Solarzellen. Die Solarzellen als Gegenstand dieser Untersuchungen sind dabei aus Materialien aufgebaut, die mittels thermischer Gasphasenabscheidung im Vakuum hergestellt werden. Das unterscheidet diese von vielen in der Literatur vorgestellten Alterungsstudien, die Polymersolarzellen behandeln. Als Standardsystem werden einfache pii-Bauelemente ausgewählt, die in ZnPc und C60 zwei gut untersuchte Materialien in der aktiven Donor-Akzeptor-Schicht nutzen. Die Ergebnisse dieser Arbeit sind dabei in drei Kapiteln zusammengefasst. In Kapitel 5 wird untersucht, wie sich verschiedene Faktoren auf die Lebensdauer der Solarzellen auswirken. Für verkapselte Solarzellen mit MeO-TPD in der Lochtransportschicht wird die thermische Beschleunigung der Degradation mit einem Arrhenius’schen Verhalten beschrieben und eine Aktivierungsenergie EA=712 meV gefunden. Aus dieser Beschreibung wird für verkapselte Solarzelle bei 100 mW cm-2 und 45°C eine Lebensdauer von 62.000 h extrapoliert, die experimentell nicht verifiziert werden kann. Auch der Einfluss der Beleuchtungsintensität auf die Degradationsgeschwindigkeit wird untersucht und kann systematisch erklärt werden: Die Beschleunigung, die sich aus einer Erhöhung der Intensität weißen Lichtes ergibt, kann beschrieben werden, indem man die Anzahl extrahierter Ladungsträger berechnet. Bei Alterungen unter verschiedene Intensitäten ist diese Zahl identisch, wenn man die Messung bei gleichem Grad der Degradation betrachtet. Diese Modell kann auch auf monochromatische Beleuchtung ausgedehnt werden und es zeigt sich bei einem Vergleich über alle untersuchten Wellenlängen, dass der Anstieg der fallenden Kurven umso steiler wird, je höher die kürzeste Wellenlänge des jeweiligen Spektrums ist. Der zweite Teil dieses Kapitels ist der Degradation unverkapselter Solarzellen mit BF-DPB als Lochtransportmaterial gewidmet. Durch Variation von Temperatur und relativer Luftfeuchte konnten beide Einflussfaktoren in einem kombinierten Modell, dem Peck-Modell, zusammengefasst werden. Dieses wurde bisher nicht zur Beschreibung des Degradationsverhaltens von Solarzellen verwendet. Eine Vorhersage der Lebensdauer bei beliebigen Werten für beide Parameter ist somit möglich. Deutlich sticht in diesem Experiment hervor, dass die Anwesenheit von Wasser die Degradation klar dominiert. Darauf folgen Messungen, bei denen die Wasserpermeationsrate (WVTR) der Verkapselung variiert wird. Dabei stellt sich heraus, dass diese besser als 10-3 g m-2 d-1 sein muss, um die Stabilität zu verbessern. Durch eine Trennung der WVTR der äußeren Barriere und jener der Aluminiumelektrode ist es möglich, den Wert WVTR(Al) zu ermitteln. Dieser beträgt 8 x10-4 g m-2 d-1. Zusätzlich kann die Wassermenge, die benötigt wird, um die untersuch-ten Solarzelle auf 50% des Startwertes zu degradieren, zu 10 mg m2 bestimmt werden. Kapitel 6 zeigt eine umfassende Charakterisierung von an Luft degradierten Solarzellen. Mit den chemischen Analysemethoden TOF-SIMS und LDI-TOF-MS können mehrere Reaktionen der verwendeten Materialien mit Luft identifiziert werden. Dabei sticht die Oxidation der BPhen-Aluminium-Grenzschicht, die zur Bildung von Al2O3 führt, hervor. Weitere Reaktionsprodukte, vor allem in Verbindung mit Fluor, welches aus der Zersetzung von C60F36 stammt, werden gezeigt. Die Oxidation der Organik-Aluminium-Grenzschicht kann mit Hilfe von Elektrolumineszenzmessungen untersucht werden. Bei diesen zeigt sich, dass die Abnahme der aktiven Fläche in vollem Umfang Ursache für die Reduktion der Kurzschlussstromdichte ist. Als Eintrittskanäle für Sauerstoff und Wasser werden neben pinholes auch die Seitenkanten der Solarzelle identifiziert. Hinweise für die flächige Diffusion von Wasser werden zusätzlich erbracht. Erster Ansatz zur Verbesserung der Langzeitstabilität ist der Austausch von BPhen durch ein dotiertes Elektronen-transportmaterial. Eine Variation von fünf Materialien zeigt, dass ein Zusammenhang zwischen Rauigkeit dieses Materials und der Lebensdauer besteht: So werden die besten Stabilität für Materialien wie C60 und Bis-HFl-NTCDI gezeigt, die mit einer geringen Rauigkeit aufwachsen. Die Lebensdauer beträgt am Beispiel von Bis-HFl-NTCDI bei [T=65°C; rH=2,2%] T50=762 h und ist damit etwa viermal so groß wie bei Verwendung von BPhen. Weitere Optimierungsversuche, zum Beispiel durch Variation der Elektrode, des p-Dotanden, oder der Invertierung der Struktur zeigen zwar zusätzliche Degradationspfade auf, führen aber zu keiner Verbesserung der Stabilität. Auf Basis zuvor durchgeführter Überlegungen zu Redoxreaktionen (organischer) Materialien mit Wasser und Sauerstoff wird zum Abschluss der Arbeit ein möglicher Aufbau für luftstabile organische Solarzellen vorgeschlagen.

In this thesis, a first-principles methodology to investigate the impact of electron-phonon interactions on the charge-carrier mobilities in organic molecular crystals has been developed. Well-known organic materials such as oligoacene and oligothienoacene derivatives were studied in detail. The nature of the intramolecular vibronic coupling in oligoacenes and oligothienoacenes was studied using an approach that combines high-resolution gas-phase photo-electron spectroscopy measurements with first-principles quantum-mechanical calculations. The electron interactions with optical phonons in oligoacene single crystals were investigated using both density functional theory and empirical force field methods. The low-frequency optical modes are found to play a significant role in dictating the temperature dependence of the charge-transport properties in the oligoacene crystals. The microscopic charge-transport parameters in the pentathienoacene, 1,4-diiodobenzene, and 2,6-diiodo-dithieno[3,2-<i>b</i>:2',3'-<i>d</i>]thiophene crystals were also investigated. It was found that the intrinsic charge transport properties in the pentathienoacene crystal might be higher than that in two benchmark high-mobility organic crystals, i.e., pentacene and sexithienyl. For 1,4-diiodobenzene crystal, a detailed quantum-mechanical study indicated that its high mobility is primarily associated with the iodine atoms. In the 2,6-diiododithieno[3,2-<i>b</i>:2',3'-<i>d</i>]thiophene crystal, the main source of electronic interactions were found along the π-stacking direction. For negatively charged carriers, the halogen-functionalized molecular crystals show a very large polaron binding energy, which suggests significantly low charge-transport mobility for electrons.

The objective of this research is to determine if it is possible to reduce the number of organic solar cells required to power a load using a DC to DC converter thereby reducing the cost of the organic solar array system. An organic solar power system designer may choose an organic implementation of a DC to DC converter to go along with the organic solar cell array. Common DC to DC converters include the buck converter, boost converter, buck/boost converter, and Cuk converter, all of which are not good candidates for organic implementation due to their use of inductors. Organic inductors are relatively more lossy than organic capacitors. So, an inductor-less DC to DC converter, such as the Dickson charge pump, would be a better candidate for organic implementation. Solar cells connected in an array configuration usually do not perform up to their full potential due to current and voltage mismatches between solar cells. These mismatches can be related to each solar cell's circuit model parameters such as the photon current density, diode ideality factor, diode reverse saturation current density, parallel resistance, and series resistance. This research varies these circuit model parameters as dependent variables, and observes the loads and power levels that make the Dickson charge pump a feasible option. The results show that current mismatch does produce an opportunity to use a DC to DC converter to save the use of a few solar cells. However, the Dickson charge pump was found to be infeasible due to an input voltage requirement that could not be met using the tested organic solar cells.

Organic electronics is a hot and modern topic which holds great promise for present and future applications. One such application is the light-emitting electrochemical cell (LEC). It can be fully solution processed and driven at low voltage providing light emission from a large surface. Inkjet printers available today can print a variety of inks, both solutions and dispersions. The technique is scalable and a quick and easy way to accurately deposit small quantities of material in user definable patterns onto a substrate. This is desirable to make low cost and efficient optical devices like displays. In this thesis it has been shown that solid electrolytes, after being dissolved in a liquid solvent, can be inkjet printed into a set of well separated distinct drops with an average maximum thickness of 150 nm. The electrolytes are commonly used in LECs and comprised by poly(ethylene glycol) with molar masses ranging from 1 – 35 kg/mol, and potassium trifluoromethanesulfonate (KCF3 SO3 )—together dissolved incyclohexanone to form an ink. The smallest achieved edge to edge distance between the printed drops was 40 μm. Together with a drop diameter of 50 μm it yields a coverage of 24% at a resolution of 280 dpi. Profiles of dried deposited drops of electrolyte were examined with a profilometer, which showed adistinct coffee ring effect on each drop. In particular, the ridges of the coffee rings were broken into pillar like shapes, together forming a structure akin to a scandinavian ancient remnant called stone ship. Different drop diameters were measured in and between the indium tin oxide samples. The drops’ speeds and sizes atejection from the nozzles seemed unchanged, and wettability is most probably the physical phenomena tolook into in order to understand what generates the differences. Local changes in surface roughness and/or surface energy, possibly originating from the cleaning process of the samples, is most likely the cause. No indications towards large differences in surface tension between the printable inks were seen, however their viscoelastic properties were not measured. As part of the thesis work a LEC characterization set-up was built. It drives a LEC at constant currentand measures the driving voltage, -current, and luminance over time. The set-up is controlled by a Labview virtual instrument and the data exported to a text-file for later analysis. The precision of the luminance measurements is ±0.1 cd/m2 for readings &lt; 50 cd/m2 , but the accuracy is uncertain. The conclusion of this thesis is that it is indeed possible to print solid electrolytes dissolved in cyclo-hexanone with an inkjet printer. However, in order to fully understand the spreading and drying of thedrops, studies of the inks’ viscoelastic properties, together with surface roughness and -energy density ofthe substrates, are needed. The largest molar mass of nicely printable poly(ethylene glycol), at an ink concentration of 10 mg/ml, was 35 kg/mol. This is comparable to the molar mass of an active light-emittingmaterial, “SuperYellow”, often used in LECs. Even though their respective molecular structures are very different, this indicates that inkjet printing of complete LEC-inks, containing both the active material and solid electrolyte, is feasible. Most probably it would require substantial tuning of the printing parameters. This thesis provides further hope for future fully inkjet printed LECs.

Orientador: Prof. Dr. Wendel Andrade Alves / Tese (doutorado) - Universidade Federal do ABC, Programa de Pós-Graduação em Nanociências e Materiais Avançados, 2016. / O consumo de produtos eletrônicos pela sociedade provoca forte impacto ambiental no momento de descartar tais eletrônicos. Neste contexto, a busca por materiais ambientalmente amigáveis está alinhada às necessidades de nosso tempo. Nanoestruturas peptídicas derivadas de aminoácidos naturais possuem grande potencial para a fabricação de uma nova geração de dispositivos biodegradáveis, utilizando a rota de síntese de baixo para cima, sem a necessidade de caros processos litográficos. Neste trabalho, nanomateriais peptídicos foram utilizados tanto em sua forma pura quanto modificados com polímeros para a criação de dispositivos eletrônicos. Os efeitos da auto-organização das nanoestruturas sobre o desempenho e eficiência desses dispositivos foram investigados. Transistores orgânicos de efeito de campo (OFETs) baseados no dipeptídeo L,L-difenilalanina foram desenvolvidos pela primeira vez, tendo apresentado razões on/off e mobilidades da ordem de 103 e de 10-3 cm2 Vs-1. Esses valores são bastante promissores na busca de componentes eletrônicos que atendam às necessidades de desempenho atuais. Um diodo orgânico emissor de luz (OLED) também foi fabricado utilizando as nanoestruturas peptídicas de L,L-difenilalanina modificadas com o polímero emissor poli[2,7-(9,9-dioctilfluoreno)]. Embora o dispositivo tenha apresentado eficiência cerca seis vezes menor comparado ao sistema produzidos com o polímero puro, a introdução de peptídeos permitiu o uso de uma quantidade menor de polímero, além de exibir taxas de biodegradabilidade cerca de 85% maiores. A integração de nanoestruturas de peptídeos com dispositivos de eletrônica orgânica pode significar o início do desenvolvimento de materiais biodegradáveis para aplicação em dispositivos com alta demanda de consumo, tendo como consequência a diminuição do impacto ambiental proveniente da utilização destes dispositivos. / The consumption of electronic products in our society leads to strong environmental impact when such devices need to be discarded. In this sense, research on environmental friendly materials is aligned with the needs of our time. Peptide nanostructures derived from natural amino acids have great potential for producing a new generation of biodegradable devices using the "bottom-up" synthesis route without need for expensive lithographic processes. In this work, peptide nanomaterials were used either in pure form or modified with polymers for designing organic electronic devices and the effects of self-organization on performance and efficiency of these devices were investigated. Organic field effect transistors (OFETs) based on the dipeptide L-L-diphenylalanine were developed for the first time, exhibiting on/off and mobility values of the order of 103 and of 10-3 cm2 Vs-1. These values are very promising and meet the current performance needs in organic devices. An organic light emitting diode (OLED) was fabricated using a combination of peptide nanostructures and 9,9-dioctylfluorene emitting polymer. Although this device shows efficiency six times lower than those build up from pure polymer, they required a lower amount of polymer in the hybrid material and exhibited biodegradability rates ~ 85% higher than architectures exclusively based on pristine polymer. Integration of peptide nanostructures with organic electronic devices represent a milestone on developing biodegradable materials for use in devices with high demand in our society, resulting in reduced environmental impact.

Morphological architecturing is one of the smart and efficient ways to maximize the number of excitons harvested from the known photoactive materials and existing fabrication technologies. Surfaces and interfaces play a vital role in absorbing light and therefore when patterned regularly, aid in the improvement of light absorption. This thesis deals with the study of light management by morphologically architecturing the organic electroactive materials. Here, morphological architecturing is carried out using electrospinning technique by optimizing various parameters. In the first part, organic photovoltaic system is tailored by morphologically modifying the conjugated polymer active layer and analyzing the enhancement in light collection and hence performance of photovoltaic devices. In the second part, the prospects of using free standing buffer layer instead of thin film buffer layer in a solar cell is evaluated. Furthermore, the study on morphological engineering of conjugated small molecule is carried out, by varying the solvents and derivatives, in order to control morphologies by understanding the underlying mechanism. Overall this thesis attempts to understand the fundamentals in morphological architecturing, by physical architecturing of the small molecules in a device for light management applications as well as demonstrating improvement in light absorption in existing organic photovoltaic systems. In the introduction chapter, a brief description of organic photovoltaics is given followed by highlighting the importance of processing methods in light management and in organic photovoltaics. The significance of structured architecture in improving the device characteristics is presented. The issues and challenges in existing architecturing techniques available in literature are discussed. Electrospinning as a tool for morphological modification for organic photovoltaics is demonstrated. This is followed by an outline of the thesis. In Chapter 2, brief description of procedures carried out for fabrication, characterization and optimization of electrospinning process parameters are discussed. The description of fabrication procedures including electrospinning, spincoating and thermal evaporation are given. Characterization techniques used in this thesis for surface and feature analysis, structural, compositional, optical and opto-electrical analyses are described. Optimization of electrospinning process parameters in obtaining various morphologies are evaluated. In Chapter 3, enhancement of device characteristics of poly (3-hexylthiophene): phenyl C61-butyric acid methyl ester (P3HT: PCBM) by changing active layer film morphology into network structure is elucidated. Network structure is provided by electrospraying assisted hierarchical assembly of short fibrils. Effect of electrospraying parameters such as solvent, polymer blend concentration, applied voltage, tip to collector distance, flow rate and deposition time are analyzed. Solvent and applied voltage are observed to be the major parameters governing the formation of network structure. The optimized conditions are used to investigate the optical and structural properties. Percent reflectance studies showed improvement in light absorption due to increase in surface area. Structural characterization studies indicate an increase in orientation of crystallites and crystallinity as compared to spincoated samples. The optimized conditions along with additional spincoated layer of P3HT:PCBM are used to fabricate bulk heterojunction device. Device characteristics exhibited an increase in short circuit current and thus increase in efficiency from 2.18% to 3.66%. There is a enhancement of 37.5% going from maximum external quantum efficiency of 40%-55% for electrosprayed and spincoated devices. It is anticipated that network morphology could be the next possible structure to be explored in organic photovoltaic materials. In Chapter 4, photonic structure is analyzed and compared. A photonics device requires uniform periodic structural arrangement. Various techniques are used to fabricate these types of structures, employing several steps of fabrication. This work proposes single step hierarchical array of equal submicron size porous structure fabricated by tuning electrospinning processing parameters. The dictating process parameters on evolving structure are high voltage, tip to collector distance and solvent. Morphological and optical investigations suggest that uniform periodic topography helps in light scattering leading to multi reflection and thus enhancement in light absorption. This structure is evaluated as active layer in organic photovoltaic devices using poly (3 hexyl thiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) blend and its device characteristics are analyzed. Consistent and reliable device characteristics obtained through photonic structure is demonstrated. Finally, comparison is drawn to network structure to assess the advantages and limitations of both morphologies as active layer in organic photovoltaics. In Chapter 5, instead of architecturing active layer the next polymer film layer in the organic solar cells, that is the hole transport layer is transformed into free standing nanofiber mats. Morphological, structural and surface wetting properties are assessed for these nanofiber mats followed by fabrication of inverted organic solar cell. The free standing nanofibers mats are obtained by electrospinning the blend of Poly(3,4-ethylenedioxythiophene) Polystyrene sulfonate (PEDOT:PSS) a conducting water soluble polymer with other water soluble polymers such as poly vinyl alcohol (PVA) and poly ethylene oxide (PEO). The study is further extended by employing two batches of PEDOT:PSS of varying conductivity that are analyzed side by side for six ternary and two binary blends each. Electrospinning parameters such as applied voltage and flow rate are optimized and fibers of diameter 150-200 nm are obtained. Maximum content of PEDOT:PSS with which free standing fiber mats could be achieved are 98 and 99%. Subsequent increase in PEDOT:PSS results in formation of beads. Surface wetting behavior showed that hydrophillicity increases with increase in PEDOT:PSS content. Devices are fabricated and the variation in characteristics and charge collection with respect to addition of PEO and PVA are discussed. In Chapter 6, a conjugated small molecule is taken as case study unlike the use of the conjugated polymer studies in previous chapters. A mechanism is proposed for tuning the sphere-spike morphology and also to control the crystallite size through solvent management using a conjugated small molecule. Electrospraying of an organic molecule is carried out using various solvents, obtaining fibril structures along with a range of distinct morphologies. Solvent characteristics play a major role in achieving the morphology of the organic material. A thiophene derivative (7, 9-di (thiophen-2-yl)-8H-cyclopenta [a]acenaphthylen-8-one) (DTCPA) of donor-acceptor-donor (DAD) architecture is used to study this solvent effect. Seven solvents with decreasing vapor pressure are selected for experiments. Electrospraying is conducted at a solution concentration of 1.5 wt % and a constant applied voltage of 15 kV. Gradual transformation in morphology of the electrospun product from spikes-sphere to only spikes is observed. A mechanism describing this transformation is proposed based on the electron micrograph analysis and XRD analysis. These data indicate that the morphological change is due to the synergistic effect of both vapor pressure and dielectric constant of the solvents. Through a reasonable control over the crystallites size and morphology along with supporting transformation mechanism theory, the work in this chapter elucidates electrospraying as a prospective method for designing the architectures in organic electronics. In Chapter 7, light management studies are carried out by morphologically architecturing the carbazole derivatives through electrospraying. The effect of derivatives on morphology is analyzed. The two carbazole derivatives; carbazole-benzothiadiazole (Cz-Bz) resulted in 2D structures and carbazole-benzothiadiazole-bithiophene (Cz-Bz-Bt) resulted in 3D structures after electrospraying. These structures are further analyzed to study the effect of vapor pressure of solvents and solution concentration. Structural characteristics indicate that electrospraying imparts change in molecular structure orientation. Optical studies showed 19 – 31% enhancement in light absorption. Further, three types of organic photovoltaic devices are fabricated and the opto-electrical properties are evaluated. Also, the effect of substrate on morphological formation is assessed. In Chapter 8, the major contributions and conclusions drawn from the morphological architecturing of both conjugated polymers and small molecules are summarized, along with few recommendations for future research.

In recent years, organic photovoltaics (OPVs) have attracted considerable attention as a potential source of renewable energy over traditional materials due to their light weight, low production cost, mechanically stability and compatibility with flexible substrates in roll to roll processing for high volume production. In the OPVs interface plays an important role in determining the performance of the device. Interface signifies formation of efficient contact with electrode, film, and transport of free charge carrier, which results in better performance in the device. Interface engineering also helps in improving mechanical robustness of the device. Hence, understanding of interface, modification and its evaluation is important in fabrication of efficient device. In this thesis interface is modified such that the performance of the device can be improved (chapter 3 and chapter 4). In Chapter 5 and chapter 6 interface is modified such that device can be fabricated on uncommon substrate. Fabrication of device on uncommon substrates (fiber reinforced plastic and flexible glass substrate), has unique challenges. In chapter 5 and chapter 6, we look at how interface is modified to overcome the challenges associated and also understand the role of interface in improving the performance of device on such substrates is discussed. In Chapter 1 we discuss about working of organic solar cells and the challenges associated in device fabrication. Understanding of interface to overcome challenges associated is explained. It also covers brief introduction to the succeeding chapters discussed in the thesis and its recent developments. To understand the properties of interface and to analyze device performance various characterization techniques have been used are discussed in chapter 2. This chapter also covers the materials and general device fabrication techniques used in this thesis. In chapter 3, a narrow bandgap (NBG) polymer used as a near IR sensitizer in P3HT: PCBM blend. Since, P3HT with a band gap of ~1.9 eV, the commonly used p-type material absorbs approximately ~25 % of incident light. Hence, MP2 (NBG polymer) is used along with P3HT: PCBM in active layer to form a ternary blend, which helps in increased absorption. Basic properties of MP2 are evaluated using UV-visible spectroscopy, differential scanning calaorimetry(DSC), thermogravimetric analyser (TGA), gel permeation chromatography (GPC) and photoluminescence (PL) techniques. To evaluate enhanced absorption of ternary UV-visible spectroscopy is carried out. Charge transfer from one moiety to other in ternary blend is evaluated using PL and Ttime resolved microwave conductivity (TRMC). Morphology of the ternary is assessed using atomic force microscope (AFM) and structural characterization is carried out by X-ray diffraction (XRD). Performance of the device is evaluated by current-voltage (J-V) characterizations. Further improved performance is supported by external quantum efficiency (EQE). Charge extraction with linear increasing voltage (CELIV) of the device is done to evaluate the recombination mechanism in the device and to assess the performance of the device. One-dimensional (1D) ZnO nanostructures provide direct paths for charge transport, and also offer large interfacial area to make them an ideal electron transport layer. In chapter 4 highly aligned ZnO nanorods is used as electron transport layer in OPV. Growth of ZnO nanorods is two-step processes, growing seed layer and growing ZnO nanorods from hydrothermal process using an appropriate seed layer. Two different soft-chemical solution- growth methods (upward and downward) are developed to fabricate self-assembled, oriented ZnO nanorods. Substrate mounting, surface properties and optical transmittance are optimized by varying the nanorods growth conditions. Further the ZnO nanorods are UV ozone treated and its effect on performance of nanostructured buffer layer based device is evaluated. In Chapter 5 OPV is fabricated on an opaque FRP substrate. Fabrication of OPV device on opaque substrate plastic is unique and hence understanding various properties is vital. Such devices fabrication require bottom up approach, with transparent electrode as the top electrode and metal electrode on the surface of FRP. FRP has inherent rough surface of about few microns RMS roughness. In order to reduce the roughness of the substrate FRP was planarized. The planarized layer is chosen, such that it chemically binds with the substrate. The chemical interaction between substrate and planarizing coating is evaluated by FTIR and Raman spectroscopy. The binding of planarized layer and FRP is evaluated using nanoscratch technique and surface energies are studied using contact angle measurements. In addition, adhesion properties of the metal electrodes, which are deposited on planarized FRP are evaluated using nanoscratch technique. Fabrication of OPV requires a top transparent electrode. Simple spin coating technique is used to optimize the top electrode. The property of top electrode is evaluated using UV-visible spectroscopy for transmittance, and sheet resistance of the electrode is characterized. OPV device is fabricated on planarized FRP substrate using optimized top transparent electrode and its PV properties is evaluated. Performance of the device is evaluated for two different bottom electrodes and further performance of device is enhanced using buffer layers. Usually flexible OPVs are fabricated on plastic substrate such as PET, PEN. However they are not structurally stable at high temperatures and have high oxygen and moisture Permeability. In Chapter 6 Organic based photovoltaic devices were fabricated on flexible glass. Flexible glass has high strength and it is also known for low oxygen and moisture permeability. Fabrication of device on flexible glass has never been done before and hence, generation of data is necessary for commercialization of the technology. Device fabrication is optimized by using two different transparent conducting layers (ITO- sputter deposited, PEDOT: PSS-solution processed) and device performance was evaluated for both. Since the substrate is flexible in nature understanding the performance of the device during flexing is important. For this 2-parallel plate flexural apparatus is fabricated for in-situ measurements along with current voltage measurements. These devices are flexed cyclically and performance of device is evaluated. Therefore, work discussed in the thesis show by modifying the interface of the device, and understanding various interfaces of the device is crucial for improving the performance of the device. Also by engineering the interface, devices can be fabricated on various types of substrate.

[pt] Este trabalho teve como objetivo fabricar e caracterizar Transistores Orgânicos Emissores de Luz (OLETs, Organic light-Emitting Transistors). Os OLETs combinam em um único dispositivo a funcionalidade elétrica de um transistor de efeito de campo orgânico e a capacidade de geração de luz, representando uma nova classe de dispositivos orgânicos com alto potencial de inovação em aplicações, como sistemas ópticos de comunicação, tecnologia de displays avançada, lasers orgânicos, fontes de luz em nanoescala e optoeletrônica orgânica integrada. Portanto, esta tese possui um caráter pioneiro, tanto para grupo de pesquisa quanto para o país, uma vez que ocorre a junção dos conhecimentos e domínio adquiridos sobre OFETs e OLEDs. Efetivamente, este trabalho de doutorado consistiu na fabricação e caracterização sistemática de diversos dispositivos OLET utilizando variadas arquiteturas e diversos materiais, comerciais e não comerciais, como o NT4N, o P13 e uma bicamada de C8-BTBT com TcTa:Ir(ppy)3. Os dispositivos foram caracterizados através de medidas elétricas e óticas, obtendo-se as curvas características. Também foram determinados seus parâmetros e propriedades de funcionamento, com destaque para as mobilidades de carga e para as eficiências obtidas. Houve também o entendimento e a implementação de um tratamento térmico na camada dielétrica, sendo parte fundamental da fabricação dos dispositivos. Os dispositivos fabricados apresentaram diferentes graus de desempenho, com destaque para a arquitetura bicamada, por apresentar a maior potência luminosa (4 microwatt) e a maior eficiência (0,5 por cento), sendo suficientes para inserir os dispositivos fabricados na categoria de dispositivos orgânicos altamente eficientes. Tal fato demonstra que o domínio da fabricação e da caracterização desta nova classe de dispositivos foi alcançado. / [en] The aim of this work was to achieve the knowledge of the fabrication and the characterization of Organic Light Emitting Transistors, OLETs, considered as one of the innovative technologies nowadays. The OLETs combine in a single device the electrical functionality of an organic field-effect transistor (OFET) and the light-generating capability. They represent a promising new class of organic devices with high potential for innovation in applications such as communication systems, advanced display technology, organic lasers, nanoscale light sources and integrated organic optoelectronics. In some way, this thesis has a pioneer character, both for our research group and for the country, since it combines different knowledge and skills about OFETs and OLEDs to achieve a new device. Actually, this work involved the systematic manufacture and characterization of several OLETs using different architectures employing commercial and noncommercial materials, such NT4N, P13 and a bilayer of C8-BTBT with TcTa:Ir(ppy)3. The devices were then characterized by electrical and optical measurements. The working parameters and properties were determined as well, highlighting the charge carrier mobilities and efficiencies obtained. The understanding and the implementation of a specific heat treatment in the dielectric layer was a fundamental part of this work for the manufacture of the devices which have different degrees of performance. With emphasis on the bilayer architecture, that presented the highest luminous power (4 microwatt) and efficiency (0,5 percent), inserting the devices manufactured in the category of highly efficient organic devices. Such fact shows that the fabrication and characterization of this new class of devices has been achieved.