This thesis deals with the design of a permanent-magnet synchronous inner rotor motor for an in-wheel application for the Shell Eco Marathon Urban concept vehicle. First of all, concepts related to permanent magnet motors are studied. Likewise, different features of permanent magnet motors are qualitatively evaluated in order to choose the most suitable. A radial flux motor is selected based on its solid, economic and acceptable characteristics. Next, a detailed study of concentrated windings is carried out. Through this investigation, undesirable configurations of pole and slot numbers due to unbalanced magnetic pull or a low fundamental winding factor will be avoided and how to determine the different winding layouts for different pole and slots configuration will be explained. As well, based on this study, and the magnetic and electric behavior of the machine, an analytical model is created. This model calculates the optimum size and characteristics of a machine in order to obtain lightweight design. After that, the design of a program based on a finite element method that simulates different situations for the machine is accomplished, dealing with the difficulties that entails the concentrated windings. Finally, through the use of this program, the machine calculated by the analytical model is analyzed, specially regarding that it does not surpass some important margin in order not to be demagnetized or not to surpass the maximum phase voltage supplied by the batteries.

The thesis presents deals with the design, analysis, test and control of permanent magnetsynchronous motor(PMSM). An analytical model was carried out based on the d-q frame and the equivalent circuit of PMSM, theanalytical model gives an approximation value of the machine parameters and is carried out byequations from the listed references. this phase includes many iteration steps, once the results wereobtained they were compared with the motor specifications and if they don’t match the requiredspecifications the process must be done again until the desired design is obtained. Once the analytical model is obtained a Finite Element Simulation was carried out using FEMMsoftware to validate the design, in this phase the designed machine in the analytical model isanalyzed and validated, once the simulation is done the results from both models are compared anddiscussed in the results chapter. It’s important to mark that during the design phase some design parameters were affected andlimited by some factors, for example, the air gap length has been magnified due to manufacturinglimits. The manufacturing process and the prototype building have been started once the optimal designwas selected, the manufacturing process was explained and a comparison study was made to selectthe best manufacturing process suitable and available for this thesis.

In this thesis, the basics of electromagnetic theory for wave-energy conversion are reviewed, some of the characteristics of the ocean wave are investigated, some of the power take-off (PTO) systems are introduced, and details about linear permanent magnetic machines, in particular, are discussed.  The thesis aims to model the novel linear transverse flux machine designed by Anders Hagnestål and to build hysteresis current controller for power factor correc- tion. Although this machine is expected to have high performance in terms of efficiency, it also exhibits a strong mutual interaction between the three phases of the machine. Thus, simplification of the actual model of the machine is im- posed to mitigate the complexity of the machine and facilitate the Simulink model. Four cases of the double band hysteresis control are studied. The cur- rents seem to be responding properly to the control scheme; however, software and hardware programming of a microprocessor would be preferable to ensurethe applicability of the control strategy in a real environment. / I detta examensarbete undersöks elektromagnetisk teori och havsvågors egenskaper. Några energiomvandlingssystem introduceras och permanentmagnetiserade maskiner diskuteras i detalj. Syftet med avhandlingen är att modelleraen ny linjär transversalflödesmaskin som är designad av Anders Hagnestål och att bygga en hysteresbaserad strömkontroll för denna. Även om maskinen förväntas prestera bra, uppvisar den också en stark ömsesidig magnetisk interaktion mellan de tre faserna. För att kunna hantera detta problem och därmed kunna genomföra simuleringar införs en förenklad elektromagnetisk modell av maskinen. En strömkontroller har implementerats i Simulink, där fyra fall av dubbelbandshystereskontroll studerats. Resultaten från simuleringarna visar att strömkontrollern fungerar. Nästa steg i projektet är att utföra mjukvaru och hårdvaruprogrammering av en mikrokontroller för att testa systemet i enverklig miljö.

In this research, an attempt is made to evaluate alternative model-predictive microgrid control approaches and to understand the trade-offs that emerge between model complexity and the ability to achieve real-time optimized system performance. Three alternative controllers are considered and their computational and optimization performance compared. In the first, nonlinearities of the generators are included within the optimization. Subsequently, an approach is considered wherein alternative (non-traditional) states and inputs of generators are used which enables one to leverage linear models with the model predictive control (MPC). Nonlinearities are represented outside the control in maps between MPC inputs and the physical inputs. Third, a recently proposed linearized trajectory (LTMPC) is considered. Finally, the performance of the controllers is examined utilizing alternative models of the synchronous machine that have been proposed for power system analysis.

No description available.

Direct drive wave energy conversion systems have been identified as a potentially major contributor to the world’s energy demands, forecasting shares of up to 25 % of the energy mix. Anders Hagnestål conducts research at the Royal Institute of Technology where a novel linear transverse flux permanent magnet generator is developed. This concept machine is particularly well-suited for the pertaining operating conditions in marine environments, producing large forces at low speeds with outstandingly low resistive losses. However, it exhibits severe magnetic saturation and draws unsymmetrical phase currents at nominal operation. In addition, it possesses a low power factor. All in all, this places stern requirements on the power electronic system and control algorithms. The aim of this thesis has been to design a functioning power conditioning system that connects the machine to the electric grid. For this purpose, a three-phase two-level voltage source converter is proposed to be back-to-back connected with two-level single-phase voltage source converters (active rectifiers) interfacing each and every machine phase. It is shown that the intermediate DC link can be maintained at a constant voltage with restricted ripple while feeding power at unity power factor to the grid by appropriately sizing the DC capacitor and adopting a feedback linearization control scheme. The phase currents can be controlled effectively by means of a cascaded gain-scheduled PID controller. By including a low-pass filter the iron losses in the machine may be suppressed even at lower switching frequencies. A constrained cost optimization indicates that the converter consequently can reach 99.1 % efficiency. Finally, with this thesis as a background, it is suggested that the thermal stresses on the selected semiconductor modules and the iron losses of the machine are evaluated to further improve the design. If higher efficiency of the active rectifiers is strived for, more complex converter topologies could be considered. / Direktdrivna vågenergiomvandlingssystem har utpekats som en potentiellt starkt bidragande resurs för att tillgodose världens efterfrågan på energi med andelar på uppemot 25 % av energimixen förutspådda. Anders Hagnestål bedriver forskning och utveckling av en ny typ av linjär permanentmagnetiserad transversalflödesmaskin vid Kungliga Tekniska Högskolan. Konceptmaskinen är särskilt väl lämpad för de rådande marina förhållandena genom att kunna producera stora krafter vid låga hastigheter med utomordentligt låga resistiva förluster. Maskinen går emellertid i kraftig magnetisk mättnad och drar asymmetriska strömmar vid nominell drift. Dessutom är effektfaktorn låg i jämförelse med standardmaskiner. Alltsomallt inför detta hårda krav på det effektelektroniska systemet och kontrollalgoritmerna. Målet med detta examensarbete har varit att designa ett funktionellt effektkonditioneringssystem som sammanfogar maskinen med det angränsande elektriska nätet. För att åstadkomma detta föreslås att en tvånivås-trefasomriktare kopplas rygg-mot-rygg till tvånivås-enfasomvandlare (aktiva likriktare) som i sin tur är kopplade till varje maskinfas. Med den här konfigurationen visas det att spänningen på den mellanliggande DC-länken kan hållas konstant med begränsat rippel, alltmedan effekt tillförs nätet vid effektfaktor ett genom att dimensionera DC-kondensatorn på rätt sätt och använda en kontrollag baserad på exakt linjärisering. Maskinens fasströmmar kan kontrolleras effektivt med hjälp av en kaskadkopplad PID-regulator med schemalagda förstärkningsfaktorer. Genom att inkludera ett lågpassfilter förväntas det att järnförlusterna i maskinen kan begränsas även vid lägre switchfrekvenser. Genom att lösa ett kostnadsoptimeringsproblem visas det att den resulterande aktiva likriktaren kan uppnå en verkningsgrad på 99.1 %. Slutligen, med det här examensarbetet som grund, föreslås det att den termiska stressen på de valda halvledarkomponentsmodulerna och järnförlusterna i maskinen utvärderas för att ytterligare förbättra designen. Om högre verkningsgrad eftersträvas hos de aktiva likriktarna kan mer komplicerade omvandlartopologier övervägas.

Stability and sustainability of operation of interconnected power converter systems has been an important focus of study in the field of power electronics and power systems. With ever-increasing application of electrical machines by means of electrification of vehicles, airplanes and shipboards, detailed study of the relating dynamics is very important to ensure the proper implementation and stable behavior of the overall system. In this work, the application of the black box approach study of the power converters has been expanded to the electrical machines. Using this modeling method, it is possible of have accurate behavior of electrical and mechanical terminals of the machine without the detailed information about the internal structure of the machine, material characteristics or topology of the machine. Instead, accurate model of electrical and mechanical terminals of the machine are achieved by measuring specific frequency responses of the machine to distinguish dynamic relation of the various electrical and mechanical quantities of the machine. The directly measured frequency responses, are coupled with the dynamics of the source and load in the electrical and mechanical terminals of the machine thus in order to decoupled the described couplings a mathematical process is used that results in decoupling of the controller and drive on the electrical side and the dynamics of the mechanical load and mechanical shaft at the mechanical terminal of the machine. Resulting model is the linear time invariant representation of the electrical machine at a specific operating point. Additionally, this work represents the application of this modeling method for accurate measurement of internal parameters of the machine such as inductances and mechanical inertia and characterization of the mechanical shaft coupler. Resulting unterminated model of the machine is a very important matter of information for system integrators and electrical and mechanical designs related to the application of the machine, to ensure the stable and sustainable operation of the machine. This work for the first time, represents the experimental implementation of this terminal behavioral modeling method for studying electrical machines as well as describes some of the practical limitations of this methodology. By incorporating and integrating a combination of commercially available devices such as frequency response analyzer, Hardware-In-The-Loop (HIL), Power-Hardware-In-The-Loop (PHIL), a test setup has been developed that is capable of control, operate and study arbitrary frame small-signal related measurements required for terminal behavioral study of the electrical machines. Resulting model of the machine that has been extracted from this modeling method is then used to compare in time domain with the real machine in the case of transient change in the mechanical load on the shaft to discover the validity of this modeling procedure. / Master of Science / According to the data from the International Energy Agency, around half of the electricity used globally is consumed by electric motors. Moreover, the growth in the electrical vehicle industry will increase their application even further, hence the development of high-fidelity models of electric machines for real-time emulation, system-level analyses, and stability studies still stands out as an important and needed research focus. New modeling concepts that go beyond the standard industry practice can be used at the design and integration stage to ensure the stable behavior of the overall system. Furthermore, convenient testing and identification pressures can help ensure the long-term operation of the system. Aligned with this trend, this thesis is studying permanent magnet synchronous machines (PMSM) using small-signal terminal-behavioral three-port networks. Having such a behavioral model of the machine available provides many opportunities for system integrators, and even enables an in-situ system observation and stability assessment at both the machine's electrical and mechanical interfaces. This capability can undoubtedly be of high importance in practice, as it is offering new insights into dynamic interactions of the electro-mechanical systems, the governor or turbine control design in ships, aircrafts, electrical vehicles, and even large synchronous machines in power plants. A so-called characterization testbed has been built that combines Hardware-In-The-Loop (HIL) and Power-Hardware-In-The-Loop (PHIL) environments, with sensor-interface boards that are used to properly scale measured signals for machine control. The Frequency-Response-Analyzer is used to sweep the proper electrical or mechanical terminal of the machine by perturbing the proper control signal within the machine controller running in PHIL and reading d-q currents, voltages, torque, and speed variables whose dynamic ratios are then obtained without the need for interrupting the normal operation of the electrical machine. The capability of acquiring such a detailed model of the machine while the machine is in operation is an important benefit of this modeling method, in comparison to the conventional identification methods widely applied in the industry. The resulting model is a linearized time invariant representation of the electrical machine at a specific operating point of interest, and can be used by system integrators to ensure the stability of the system using well known stability assessment methodologies. Furthermore, this modeling strategy has been experimentally verified for the first time on electrical machines, and the resulting model has been compared with the transient behavior of the machine in the presence of a step change in the mechanical load of the machine.

The unconventional improvements in the power electronics field have been the primary reason for massive deployment of renewable energy sources in the electrical power grid over the past several decades. This needed trend, together with the increasing penetration of micro-, and nano- grids, is bringing significant improvements in system controllability, performance, and energy availability, but is fundamentally changing the nature of electronically-interfaced sources and loads, altering their conventionally mild aggregate dynamics, and inflicting low- and high- frequency dynamic interactions that never before existed at this magnitude. This problem is not restricted only to the grid; modern electronic power distribution systems built for airplanes, ships, electric vehicles, data-centers, and homes, comprise dozens, even hundreds of power electronics converters, produced by different manufacturers, who provide very limited details on converters' dynamic behavior - distinctiveness that has the highest impact on how two converters, or converter and a system interact. Consequently, substantial dispersion of power electronics into the future grid will significantly depend on engineers' capability to understand how to model and dynamically control power flow and subsystem interactions. It is therefore essential to continue developing innovative methods that allow easier system-level modeling, continuous monitoring of dynamic interactions, and advanced control concepts of power electronics converters and systems. The dissertation will start with a "black box" approach to modeling of three-phase power electronics converters, introducing a method to remove source and load dynamics from in-situ measured terminated frequency responses. It will be then shown how converter, itself, can perform an online stability assessment knowing its own unterminated dynamics, and being able to measure all terminal immittances. The dissertation will further advance into an approach to control power electronics converters based on the electro-mechanical duality with synchronous machines, and end with selected examples of system-level operation, where small-signal instability in multi-source power systems can be mitigated using this concept. / Ph. D. / The modern technological advancements and ever-increasing needs for a sustainable future silently demand a serious revision of the conventional practice in electricity production, distribution, and utilization. These technologies are already challenging the limits of the biggest and most complex system ever built by humankind - the electrical grid. One practical solution to this problem is much higher dispersion of electronic power conversion systems capable of decoupling dynamics between system sources, distribution, and loads, while improving system controllability, reliability, and efficiency. Such a trend is already happening, and there has been an increased immersion of power electronics converters in electric cars, ships, airplanes, and the grid, in an effort to replace their traditional thermal, mechanical, hydraulic, and pneumatic systems. The goals have been to reduce the size, weight, and operational costs while increasing efficiency and reliability. In all these applications, a majority of energy sources and loads are interfaced to the power system through power electronics converters ranging in power from few watts to hundreds of megawatts. However, massive dispersion of power electronics into the future grid will significantly depend on engineers’ capability to understand how to model and dynamically control power flow and subsystem interactions. It is important to continue researching innovative methods that allow easier system-level modeling, continuous monitoring of interactions, and advanced control concepts of power electronics converters and systems. This dissertation hence addresses modeling of power electronics converters using their behavioral models, and shows how these models can assist the stability assessment of the system converters operate in. Additionally, dissertation presents an alternative way to control power electronics converters to behave as synchronous machines, and how this concept can be used to mitigate some stability problems.

Afin de rendre les machines synchrones à aimants permanents plus attractives pour l'aéronautique (actionneurs de commande de vol, systèmes de freinage, train d'atterrissage ...), il peut être intéressant de réduire le nombre de modules d'électronique de puissance utilisés en les mutualisant. De nombreuses études ont été réalisées pour des systèmes composés de plusieurs machines asynchrones et principalement en traction ferroviaire, mais peu concernent les machines synchrones. Après avoir étudié différentes structures envisageables, les travaux développés lors de cette thèse présentent une étude originale d'un système composé de deux machines synchrones à aimants permanents connectées en parallèle sur un onduleur unique mutualisé. Ces machines ont des caractéristiques identiques ou proches et doivent être pilotées à la même vitesse. La structure de commande retenue lors de cette thèse est de type maître-esclave: seule une des deux machines est autopilotée (la machine maître), l'autre (la machine esclave) fonctionnant en boucle ouverte. Afin d'assurer la stabilité d'un tel système, le synchronisme des deux moteurs doit toujours être respecté. Une stratégie de commande, qui choisit quel est le moteur maître, en prenant en compte la variation des paramètres internes et externes du système, est alors instaurée. Dans ces conditions, les évolutions théoriques des différentes variables sont déterminées. Pour valider ces résultats, un processus expérimental est mis en place. Les nombreux résultats obtenus en simulation et expérimentalement permettent alors de confirmer les résultats théoriques: que ce soient les paramètres mécaniques ou électriques qui varient, la stabilité du système est toujours garantie. Le cas supplémentaire où les deux machines déplacent une charge mécanique commune avec une liaison mécanique rigide entre les deux machines, est finalement développé. Une autre stratégie de commande, dont la structure et les résultats sont également présentés dans cette thèse, est alors nécessaire. / To make permanent magnet synchronous machines more attractive for aerospace (flight control actuators, braking systems, landing gear ...), it may be advantageous to reduce the number of power electronic modules used in the pooling. Many studies have been performed for systems composed of several machines and asynchronous traction primarily, but little concern synchronous machines. After considering various possible structures, this Ph.D. thesis presents an original study of a system consisting of two permanent magnet synchronous machines connected in parallel on a single shared inverter. These machines have characteristics identical or similar and must be driven at the same speed. The control structure chosen in this Ph.D. thesis is a master-slave : only one machine, called master machine is self-piloted, the other (the slave machine) operating in open loop. To ensure the stability of such a system, the timing of the two engines should always be respected. A control strategy, which selects which is the master motor, taking into account the variation of internal and external parameters of the system is then introduced. Under these conditions, the theoretical developments of the different variables are determined. To validate these results, an experimental process is established. The numerous results obtained in simulation and experiments are then used to confirm the theoretical results : whatever the mechanical or electrical parameters variation, system stability is always guaranteed. The additional case, when both machines move a mechanical load with a common rigid mechanical connection between two machines, is finally developed. Another required control strategy, the structure and the results are also presented in this Ph.D. thesis.

La problématique de recherche abordée dans ce mémoire de thèse découle de l’étude approfondie d’une association convertisseur-machine dédiée aux modes traction et recharge d’un véhicule électrique. Il s’agit d’un onduleur triphasé constitué de trois onduleurs monophasés connectés à une machine triphasée à phases indépendantes.Dans le chapitre II, une étude comparative entre deux solutions industrielles montre que l’architecture étudiée offre des caractéristiques compétitives notamment en termes de rendement global du convertisseur, performances mécaniques, et surface de silicium nécessaire.Par ailleurs, outre la possibilité de mutualiser les trois fonctions du véhicule que sont la traction, la recharge (rapide ou lente) et l’assistance du réseau électrique, cette topologie offre plusieurs atouts : des possibilités variées d’alimentation et donc un potentiel intéressant de reconfiguration en marche dégradée. La thématique abordée dans les chapitres III et IV est donc centrée sur l’optimisation des stratégies de contrôle de cette structure vis-à-vis de deux types de défauts : les imperfections intrinsèques du système d’une part et les défaillances accidentelles d’autre part.Dans un premier temps, un travail approfondi sur les méthodes de modulation de largeur d’impulsion a permis de synthétiser une stratégie offrant une faible sensibilité vis-à-vis des imperfections de la commande et de la non-linéarité du convertisseur. Dans un second temps, il a été montré qu’en cas de défaillance d’un composant à semi-conducteur, il était obligatoire de recourir à la reconfiguration matérielle de la topologie. L’architecture permettant la continuité de service a été étudiée du point de vue de sa commande. Son analyse nous a amenés à proposer une structure de contrôle basée sur des solutions automatiques simples et efficaces. Finalement, le principe du fonctionnement en marche dégradée a été étendu au fonctionnement normal dans le but d’en améliorer le rendement sur cycle. / This Ph.D. thesis focuses on a novel combination of a frequency converter and an electric machine specially dedicated to traction drive and battery recharging modes of an electric vehicle (EV). This power architecture is composed of a six legs voltage inverter connected to a three-phase open-end winding machine. Chapter II details a quantitative comparison between two industrial power architectures and concludes that the SOFRACI powertrain is a competitive solution in terms of power converter efficiency, drive mechanical performances, and required silicon area.This architecture offers the attractive possibility of combining three important functions: traction and braking, battery charging and connecting the energy storage to a smart grid. In addition, this topology offers several advantages such as various motor feeding possibilities and a high degree of reconfiguration in degraded operating mode. The third and fourth chapters of this thesis concern the optimization of control strategies with regard to two types of faults: firstly the inherent imperfections in the converter itself (non modeled non-linearity and ineffective synchronization of control values) and secondly accidental failures. In the first case, an analysis of the pulse width modulation (PWM) methods enables the creation of a PWM strategy with a very low sensitivity to PWM uncertainties and the non-linear behavior of the power converter.In the second case, in the event of a faulty semiconductor device, it is shown that a hardware reconfiguration is required to enable an emergency traction mode. The sustainability of the traction mode is then examined with respect to the control strategy. This analysis leads to an innovative control structure based on basic and easy to implement solutions. Finally, the degraded mode operation principles have been extended to normal mode operation for the purpose of enhancing the cycle efficiency.