Les céramiques bioinertes (zircone, alumine), sont utilisées dans des dispositifs médicaux pour l’orthopédie et l’odontologie. Leurs surfaces peuvent avoir plusieurs fonctions : fixation du dispositif dans le milieu vivant (ex : implants dentaires), rôle tribologique (prothèses articulaires)… Dans tous les cas, ces surfaces sont traitées pour maximiser leur performance, mais ces modifications peuvent entrainer des conséquences négatives. Ainsi, le 2e chapitre montre qu’introduire de la rugosité par sablage joue sur l’intégrité mécanique et sur la stabilité à long terme de l’alumine, de la zircone et d’un composite alumine-zircone. Par ailleurs, dans les prothèses articulaires, la lubrification joue un rôle fondamental pour minimiser l’usure et donc augmenter la durée de vie moyenne des implants, permettant en outre de favoriser l’adsorption de protéines réduisant le contact direct entre les deux surfaces glissantes. La chimie des surfaces (y compris la présence de contamination) peut modifier ces aspects. Dans le 3e chapitre de ma thèse j’ai étudié l’effet de la contamination et des différentes techniques de nettoyage permettant de la réduire sur la mouillabilité des matériaux typiquement utilisés dans les prothèses de hanche, et sur l’adsorption de protéines à leurs surfaces. Finalement, les cellules utilisent les protéines en surface comme points de fixation et identification. Les implants avec une surface capable de recruter plus de protéines aidant à l’adhésion des cellules auront plus des chances d’être intégrés que des implants recrutant des protéines qui empêchent l’adhésion. Dans le 4e chapitre, j’ai exploré un nouveau concept de modification de surface de la zircone consistant en un greffage d’organosilanes directement sur sa surface, de manière à prouver le potentiel de cette technique à améliorer l’ostéointegration sans diminuer la performance mécanique. / Bioinert ceramics (zirconia, alumina) are used in medical devices in orthopedics and dentistry. Their surfaces may provide different functions: fixation of the device in the living tissue (e.g. dental implants), tribological role(joint substitutions),… In all cases the surfaces are treated to maximize their performance, but this modifications may entail negative consequences. The use of roughness to promote osseointegration of implants is a common practice, especially on dental implants. Roughening is often conducted by mechanical treatments, the most common being sandblasting. Therefore, chapter 2 focus on the implications of roughening by sandblasting on the mechanical behaviour of zirconia, alumina and a zirconia-alumina composite, and the differences between them. The work brought in chapter 3 was carried out entirely during a six-month secondment at CeramTec GmbH. In a bearing couple, lubrication mechanisms are complex and wettability and proteins play a yet-to understand role. The study compared the wettability of different materials, their ability to welcome protein adsorption and the effect of different cleaning procedures on wettability measurements and protein adsorption. Finally, the influence of the surface on cell activity is not driven exclusively by roughness: chemical modifications of the surface may enhance the perception of cells for the surface, and by careful tuning of the surface properties one may achieve a better integration without the downsides of roughness. In chapter 4, we explored a novel modification of zirconia, based on known techniques in chemistry, which introduces molecules with special functional groups capable of rendering the surface friendlier for cell adhesion, and opening the window for new exciting developments in the field of bioinert ceramics.

L'objectif de cette thèse était de développer et de caractériser la microstructure et les propriétés mécaniques des céramiques bio-inspirées. L'alumine inspirée par la nacre fabriquée par texturation à la glace (freeze-casting), précédemment développée dans le cadre de la thèse de F. Bouville, a été choisie comme matériau de référence. La simplification et le changement d’échelle du procédé d’élaboration des matériaux ont été étudiés. Le procédé sophistiqué de freeze-casting a été remplacé par le pressage uniaxial à cru. Les mesures de diffraction des électrons rétrodiffusés ont confirmé le bon alignement après frittage des plaquettes d'alumine utilisées pour préparation du matériau. Le cycle de frittage assisté par effet de champs a été adapté à de plus grandes quantités de poudre céramique et d'additifs organiques. La deuxième partie du projet a été consacrée à la modification de l'interphase entre les plaquettes d'alumine, afin d’améliorer les propriétés mécaniques du matériau. Diverses possibilités ont été explorées: ajout de poudre de zircone, dépôt de zircone sur les plaquettes par réaction sol-gel ou substitution de la phase vitreuse par du graphène. Tous les matériaux obtenus ont été caractérisés par flexion quatre points sur des barrettes entaillées. La troisième partie de cette étude a porté sur le développement de composites multicouches métal/céramique, par frittage simultané d'alumine et de titane. L'épaisseur et la composition de la feuille de titane ont été modifiées pour étudier leur influence sur les phénomènes de diffusion lors du frittage. Les composites ont été caractérisés par MEB, EBSD, spectroscopie à rayons X à dispersion d'énergie et tomographie à rayons X au synchrotron. La fabrication simplifiée des matériaux permet de préparer des échantillons de plus grandes dimensions de céramiques inspirées par la nacre, sans passer par une étape de freeze-casting. Cependant, la croissance des grains doit être limitée pour maintenir de bonnes propriétés mécaniques. La modification de l'interphase entre les plaquettes d'alumine n'a pas amélioré les propriétés mécaniques des matériaux par rapport au matériau de référence. D'autre part, le dépôt de nano-zircone sur la surface des plaquettes semble prometteur et devrait faire l'objet d'études plus poussées. Dans le cas des composites alumine/titane, les composites architecturées multiéchelles ont été fabriqués de manière assez simple. Cependant, il est crucial d'éviter la fissuration des feuilles de métal afin d’améliorer les propriétés mécaniques. / The goal of this thesis was to develop and characterize the microstructure and the mechanical properties of bioinspired ceramic composites. Nacre-like alumina fabricated by freeze-casting previously developed in Bouville thesis was chosen as a reference material. Simplifying and up-scaling material fabrication was intended. Architectural levels were added to the microstructure to further improve mechanical properties of the material. Sophisticated processing by freeze-casting was substituted by uniaxial pressing. Electron backscatter diffraction observations confirmed the good alignment of alumina platelets used to prepare the material. The field assisted sintering cycle was adapted to greater quantities of ceramic powder and organic additives. The second part of the project was dedicated to the modification of the interphase between alumina platelets. Various possibilities were explored: adding fine zirconia powder, depositing zirconia on the platelets by sol-gel reaction, or substituting the glassy phase by graphene. All obtained materials were characterized by four point bending on notched bars. The third part of this study was focused on the development of multilayered metal/ceramic composites, by simultaneous sintering of alumina and titanium. The titanium foil thickness and composition were varied. The composites were characterized by SEM, EBSD, energy dispersive X-ray spectroscopy and synchrotron X-ray tomography. Detailed microstructural and chemical characterization was performed to understand mechanisms of titanium diffusion into ceramic matrix. Simplified material fabrication allows to prepare larger samples of nacre-like ceramics. However grain growth should be limited to maintain good mechanical properties. Modification of the interphase between alumina platelets did not improve mechanical properties of the materials as compared to the reference material. On the other hand, depositing nano-zirconia on platelets surface seems promising and should be further investigated. In case of alumina/titanium composites, a multiscale architecture composites were process in a rather simple way. However, avoiding metal foil cracking is crucial to improve mechanical properties.

A new design AMTEC converter model was developed, and its effectiveness as a design tool was evaluated. To develop the model, requirements of the model were defined, several new design models were successively developed, and finally an optimal new design model was developed. The model was created within Sinda/Fluint, with its graphical interface, Thermal Desktop, a software package that can be used to conduct complex thermal and fluid analyses. Performance predictions were then correlated and compared with actual performance data from the Road Runner II AMTEC converter. Predicted performance results were within 10% of actual performance data for all operating conditions analyzed. This accuracy tended to increase within operating ranges that would be more likely encountered in AMTEC applications. Performance predictions and parametric design studies were then performed on a proposed new design converter model with a variety of annular condenser heights and with potassium as a working fluid to evaluate the effects of various design modifications. Results clearly indicated the effects of the converter design modifications on the converter's power and efficiency, thus simplifying the design optimization process. With the close correlation to actual data and the design information obtained from parametric studies, it was determined that the model could serve as an effective tool for the design of AMTEC converters.

Catalytic combustion is an environmentally benign technologywhich has recently reached the stage of commercialization.Palladium is the catalyst of choice when considering gasturbines fuelled with natural gas because of its superioractivity for methane oxidation. Several fundamental issues arestill open and their understanding would result in animprovement of the technology. Hence, the work presented inthis thesis aims at the identification of some of theparameters which govern the combustion activity ofpalladium-based catalysts. The first part of this work gives a background to catalyticcombustion and a brief comparison with other existingtechnologies. Paper I reviews some of the issues related tomaterial development and combustor design. The second part of this thesis consists of an experimentalinvestigation on palladium-based catalysts. The influence ofthe preparation method onthe properties of these catalystmaterials is investigated in Paper II. Paper III examines theactivity of the following catalysts: Pd/Al2O3, Pd/Ba-Al2O3 andPd/La-Al2O3. Specific attention is given to the metal-supportinteraction which strongly affects the combustion activity ofpalladium. The effect of doping of the support by addition ofcerium is reported in Paper IV. Finally, the deactivation of combustion catalysts isconsidered. The various deactivation processes which may affecthigh temperature combustion catalysts are reviewed in Paper V.Paper VI focuses on the poisoning of supported palladiumcatalysts by sulphur species. Palladium exhibits a higherresistance to sulphur poisoning than transition metals.Nevertheless, the nature of the support material plays animportant role and may entail a severe loss of activity whensulphur is present in the fuel-air mixture entering thecombustion chamber. <b>Keywords</b>: catalytic combustion, gas turbine, methane,palladium, alumina, barium, lanthanum, oxidation, preparation,temperature-programmed oxidation (TPO), decomposition,reoxidation, X-ray photoelectron spectroscopy (XPS),metal-support interaction, deactivation, sulphur, poisoning.The cover illustration is a TEM picture of a 100 nm palladiumparticle supported on alumina

Glyphosate (N-(phosphonomethyl)glycine, PMG, H3L) is a widely used organophosphorous herbicide. It interacts with metal ions and mineral surfaces, which may affect its mobility, degradation and bioavailability in the environment. However, these interactions are far from fully understood. This thesis is a summary of five papers discussing the complexation of PMG with metal ions in aqueous solution and the adsorption of PMG and/or Cd(II) on different mineral surfaces. The complexation of PMG with the metals Cd(II) or Al(III) in aqueous solution was investigated with macroscopic and molecular scale techniques. Potentiometric titration data were combined with EXAFS, ATR-FTIR and NMR spectroscopic data to generate solution equilibrium models. In the PMG-Cd(II) system, only mononuclear complexes were formed, while both mono and binuclear complexes were observed in the PMG-Al(III) system. EXAFS, ATR-FTIR, and XPS measurements showed that PMG adsorbs to the surfaces of goethite (α-FeOOH), aged γ-alumina (γ-Al2O3) and manganite (γ-MnOOH) through one oxygen of its phosphonate group to singly-coordinated surface sites. Surface complexation models consistent with these spectroscopic results were fit to adsorption data using the 1pK reaction formalism. Electrostatic effects were accounted using either the Extended Constant Capacitance Model (ECCM) or the Basic Stern Model (BSM), and the charge of the surface complexes was distributed over the different planes. The formation of the surface complexes was described according to the following reactions: ≡MeOH(0.5-) + H3L &lt;=&gt; ≡MeHL(1.5-) + H2O + H+ ≡MeOH(0.5-) + H3L &lt;=&gt; ≡MeL(2.5-) + H2O + 2H+ The coadsorption of PMG and Cd(II) on the surfaces of goethite and manganite results in the formation of ternary mineral-PMG-Cd(II) surface complexes, as suggested from EXAFS results. Previous EXAFS measurements have also established the coordination geometries for the binary goethite-Cd(II) and manganite-Cd(II) surface complexes. In addition to the surface reactions in the binary mineral-Cd(II) and mineral-PMG systems, a single ternary complex with the stoichiometry ≡MeLCd(OH)(1.5-) was sufficient to explain coadsorption data: ≡MeOH(0.5-) + H3L + Cd2+ &lt;=&gt; ≡MeLCd(OH)(1.5-) + 3H+ It was concluded that the affinity of PMG for the three mineral systems decreases within the series: goethite &gt; aged γ-Al2O3 &gt; manganite. The formation of the ternary surface complex is more significant on goethite surfaces than on manganite surfaces.

The primary intention with this Doctoral thesis is to fillin the knowledge gaps and raise the level of understandingregarding the different metal dusting mechanisms in general andexplain the process in detail for high alloyed materials.Considerable effort is put into identifying the driving forcesand elucidating the diffusional processes in metal dusting. The results are based on a series of long-term laboratory exposures of stainless steels and high-performance commercial alumina-forming Fe- and Ni-base alloys in synthesis gasmixtures, plus a separate shorter study on ultra pure iron. ANi-base alloy was also investigated after a two years field exposure in a methanol plant. Post exposure metallographic examinations and analysis aswell as thermodynamic calculations were made in order toidentify and describe the operating metal dusting mechanisms.Two main mechanisms were previously used to explain metaldusting, one on the basis of decomposition of metastable carbides (Type I) the other on graphite formation (TypeII). A new metal dusting mechanism has been identified in this Thesis which appears on high alloyed steels and Ni-base alloys,an active corrosion induced by carbon and oxygen, denoted TypeIII. Both the mechanisms and the type of corrosion products were consistent with the thermodynamic conditions of the material under the influence of a carbon and oxygen gradient.It was shown that this mechanism not only accelerates the metaldusting process, in fact, it determines the overall metaldusting kinetics on stainless steels and Ni-base alloys. Another feature, which may occur at temperatures where metalbulk and even static grain boundary diffusion is too slow forexplaining the metal dusting corrosion process, was identifiedon a Ni-base alloy. It involves a fast growing cellular structure with discontinuous precipitated carbides whichprovides fast metal dusting kinetics by the Type IIImechanism. A Type IV metal dusting mechanism, continued fragmentationby graphitization until nano-sized particles are formed andcatalyse carbon nanotube formation is also described. Thesteady state process and the driving force for metal dusting onpure iron was identified and described. With these additional processes it is now possible to extendour understanding of the metal dusting processes to a widerange of engineering alloys. / QC 20100825

Ionic transport in metal oxides is crucial for the functioning of a broad range of different components, such as heat resistant alloys designed for high temperature applications and oxide electrolytes in solid oxide fuel cells. This thesis presents results from in situ electrochemical studies of properties related to ionic transport in metal oxides that are important for their applications as protective oxides and ionic conductors. Heat resistant alloys of alumina-former type are known to form an adherent, slowly growing and protective aluminium oxide (Al2O3) scale that protects metals from chemical degradation at high temperature. In situ impedance spectroscopy was used to study highly pure and dense samples of a-alumina in the temperature range 400 – 1000 °C. It was shown that surface conduction on the sample could severely distort the measurement below 700 °C. The magnitude of the distortions appeared to be sensitive to the type of electrodes used. The use of a so-called guard electrode was shown to effectively block the surface conduction in the measurements. By varying the grain size of the sintered alpha-alumina samples, the influence of grain size on the overall conductivity of the a-alumina was studied. It was shown that the activation energy for conductivity increased as the grain size decreased. Molecular dynamics calculations were performed in order to elucidate whether Al- or O ions are dominant in the ionic conductivity of the alpha-alumina. Comparing the calculation and experimental results, the dominating charge carrier was suggested to be oxygen ions. Moreover, the ionic transport in thermally grown alumina-like oxide scales formed on a FeCrAl alloy was studied in situ by impedance spectroscopy between 600 and 1000 °C. It was shown that the properties of these scales differ largely from those of pure and dense alpha-alumina. Furthermore, the conductivity is mainly electronic, due to the multiphase/multilayer microstructure and substantial incorporation of species from the base metal. However, the diffusivity obtained from the ionic conductivity was in line with diffusion data in literature obtained by other methods such as thermogravimetry. Besides, the initial stage of oxidation of a number of Fe-, Ni- and Co-based alloys at temperatures between 500 and 800 °C was studied in situ by high temperature cyclic voltammetry, in which the oxygen activity was changed over a wide range. From the resulting voltammograms the redox reactions occurring on the alloy surface could be identified. It was concluded that the base metal oxidized readily on these alloys before a protective chromia- or alumina-like scale is formed. The base metal oxide is most likely incorporated into the more protective oxide. Further, the oxygen ionic conductivity of highly pure and fully dense yttria-stabilized zirconia produced by spark plasma sintering was studied by impedance spectroscopy. The aim was to evaluate intrinsic blocking effects on the ionic conduction associated with the space charge layer in the grain boundary region. It was observed that the ionic conductivity of the spark plasma sintered oxides is equal or slightly higher than what has been achieved by conventional sintering methods. In addition, it was shown that the specific grain boundary conductivity increases with decreasing grain size, which can be explained by a decreasing Schottky barrier height (i.e., decreasing blocking effect). The quantitative results from this work verify the space charge model describing the influence of grain size on the ionic conductivity of yttria-stabilized zirconia through dopant segregation and oxygen vacancy depletion along the grain boundaries. / QC 20100825

This thesis summarizes the methods and major findings of Ni-W(P)/ã-Al2O3 nitride cata-lyst synthesis, characterization, hydrotreating activity, kinetic analysis and correlation of the catalysts activities to their synthesis parameters and properties.<p> The range of parameters for catalyst synthesis were W (15-40 wt%), Ni (0-8 wt%), P (0-5 wt%) and nitriding temperature (TN) (500-900 °C). Characterization techniques used included: N2 sorption studies, chemisorption, elemental analysis, temperature programmed studies, x-ray diffraction, scanning electron microscopy, energy dispersive x-ray, infrared spectroscopy, trans-mission electron microscopy and x-ray absorption near edge structure. Hydrodesulfurization (HDS), hydrodenitrogenation (HDN) and hydrodearomatization (HDA) were performed at: tem-perature (340-380 °C), pressure (6.2-9.0 MPa), liquid hourly space velocity (1-3 h-1) and hydro-gen to oil ratio (600 ml/ml, STP).<p> The predominant species on the catalyst surface were Ni3N, W2N and bimetallic Ni2W3N. The bimetallic Ni-W nitride species was more active than the individual activities of the Ni3N and W2N. P increased weak acid sites while nitriding temperature decreased amount of strong acid sites. Low nitriding temperature enhanced dispersion of metal particles. P interacted with Al2O3 which increased the dispersion of metal nitrides on the catalyst surface. HDN activity in-creased with Ni and P loading but decreased with increase in nitriding temperature (optimum conversion; 60 wt%). HDS and HDA activities went through a maximum with increase in the synthesis parameters (optimum conversions; 88. wt% for HDS and 47 wt% for HDA). Increase in W loading led to increase in catalyst activity. The catalysts were stable to deactivation and had the nitride structure conserved during hydrotreating in the presence of hydrogen sulfide.<p> The results showed good correlation between hydrotreating activities (HDS and HDN) and the catalyst nitrogen content, number of exposed active sites, catalyst particle size and BET surface area.<p> HDS and HDN kinetic analyses, using Langmuir-Hinshelwood models, gave activation energies of 66 and 32 kJ/mol, respectively. There were no diffusion limitations in the reaction process. Two active sites were involved in HDS reaction while one site was used for HDN. HDS and HDN activities of the Ni-W(P)/ã-Al2O3 nitride catalysts were comparable to the corre-sponding sulfides.

This thesis summarizes the methods and major findings of Ni-W(P)/ã-Al2O3 nitride cata-lyst synthesis, characterization, hydrotreating activity, kinetic analysis and correlation of the catalysts activities to their synthesis parameters and properties.<p> The range of parameters for catalyst synthesis were W (15-40 wt%), Ni (0-8 wt%), P (0-5 wt%) and nitriding temperature (TN) (500-900 °C). Characterization techniques used included: N2 sorption studies, chemisorption, elemental analysis, temperature programmed studies, x-ray diffraction, scanning electron microscopy, energy dispersive x-ray, infrared spectroscopy, trans-mission electron microscopy and x-ray absorption near edge structure. Hydrodesulfurization (HDS), hydrodenitrogenation (HDN) and hydrodearomatization (HDA) were performed at: tem-perature (340-380 °C), pressure (6.2-9.0 MPa), liquid hourly space velocity (1-3 h-1) and hydro-gen to oil ratio (600 ml/ml, STP).<p> The predominant species on the catalyst surface were Ni3N, W2N and bimetallic Ni2W3N. The bimetallic Ni-W nitride species was more active than the individual activities of the Ni3N and W2N. P increased weak acid sites while nitriding temperature decreased amount of strong acid sites. Low nitriding temperature enhanced dispersion of metal particles. P interacted with Al2O3 which increased the dispersion of metal nitrides on the catalyst surface. HDN activity in-creased with Ni and P loading but decreased with increase in nitriding temperature (optimum conversion; 60 wt%). HDS and HDA activities went through a maximum with increase in the synthesis parameters (optimum conversions; 88. wt% for HDS and 47 wt% for HDA). Increase in W loading led to increase in catalyst activity. The catalysts were stable to deactivation and had the nitride structure conserved during hydrotreating in the presence of hydrogen sulfide.<p> The results showed good correlation between hydrotreating activities (HDS and HDN) and the catalyst nitrogen content, number of exposed active sites, catalyst particle size and BET surface area.<p> HDS and HDN kinetic analyses, using Langmuir-Hinshelwood models, gave activation energies of 66 and 32 kJ/mol, respectively. There were no diffusion limitations in the reaction process. Two active sites were involved in HDS reaction while one site was used for HDN. HDS and HDN activities of the Ni-W(P)/ã-Al2O3 nitride catalysts were comparable to the corre-sponding sulfides.

<p>Catalytic combustion is an environmentally benign technologywhich has recently reached the stage of commercialization.Palladium is the catalyst of choice when considering gasturbines fuelled with natural gas because of its superioractivity for methane oxidation. Several fundamental issues arestill open and their understanding would result in animprovement of the technology. Hence, the work presented inthis thesis aims at the identification of some of theparameters which govern the combustion activity ofpalladium-based catalysts.</p><p>The first part of this work gives a background to catalyticcombustion and a brief comparison with other existingtechnologies. Paper I reviews some of the issues related tomaterial development and combustor design.</p><p>The second part of this thesis consists of an experimentalinvestigation on palladium-based catalysts. The influence ofthe preparation method onthe properties of these catalystmaterials is investigated in Paper II. Paper III examines theactivity of the following catalysts: Pd/Al2O3, Pd/Ba-Al2O3 andPd/La-Al2O3. Specific attention is given to the metal-supportinteraction which strongly affects the combustion activity ofpalladium. The effect of doping of the support by addition ofcerium is reported in Paper IV.</p><p>Finally, the deactivation of combustion catalysts isconsidered. The various deactivation processes which may affecthigh temperature combustion catalysts are reviewed in Paper V.Paper VI focuses on the poisoning of supported palladiumcatalysts by sulphur species. Palladium exhibits a higherresistance to sulphur poisoning than transition metals.Nevertheless, the nature of the support material plays animportant role and may entail a severe loss of activity whensulphur is present in the fuel-air mixture entering thecombustion chamber.</p><p><b>Keywords</b>: catalytic combustion, gas turbine, methane,palladium, alumina, barium, lanthanum, oxidation, preparation,temperature-programmed oxidation (TPO), decomposition,reoxidation, X-ray photoelectron spectroscopy (XPS),metal-support interaction, deactivation, sulphur, poisoning.The cover illustration is a TEM picture of a 100 nm palladiumparticle supported on alumina</p>