本研究在減低Wimax mesh mode環境中media access階段會造成的delay現象。我們發現當subscriber station (SS)訊務繁忙時，競爭transmission opportunity (TO)以及3-way handshake的過程容易失敗，造成傳輸效率降低，封包的delay也會增加。同時我們也發現封包的延遲還來自minislot的不良配置。因為原始的Wimax mesh mode對於minislot的配置會造成預約過晚的問題，當預約時間被延長，資料就必須無條件的增加等待時間，因此我們將針對這些問題進行改善，降低在訊務繁忙的狀況下，傳輸效率低落的問題。 我們使用兩種方式來改善上述的問題，其一是由Bayer [4]所提出的動態調整holdoff指數(dynamic holdoff exponent)的方式，藉由調整holdoff指數的大小來縮短holdoff時間，以縮短傳輸延遲；另外，我們也提出一個以節點的臨接區域為配置基準(Neighborhood-Based Minislot Allocation, NBMA) 的方法，透過與其相鄰的節點交換訊息，優化minislot的配置。我們用這兩種方式減少IEEE 802.16中媒體存取階段所造成的傳輸延遲。 實驗結果顯示，在網路負載較輕的情況下，NBMA可以有效的將delay降低為原來的七分之一，改善幅度將近85%，抖動率(jitter)的部分亦有20%的改善，並略為提高傳輸效能8%左右；而當網路負載較重時，delay的改善程度仍有40%左右，jitter部分改善了12%，傳輸效能亦有6%的改善。證明了我們的方法確實可行，並且在改善delay方面有顯著的效果。 / IEEE 802.16 mesh network is a new environment of wireless network. It was designed as a self-organized, distributed scheduling, and multi-hop network. However, it is not robust enough to handle a heavy loading environment for lacking of QoS support. Our research is trying to reduce its media access delay, which comes from both TO (transmission opportunity) competition and improper minislot allocation. TO competition will extend the MSH-DSCH (mesh distributed scheduling) interval and slow down the exchanging speed of control message. Improper minislot allocation comes from the distributed scheduling of minislot. When a subscriber station (SS) allocates too much minislot for low-level traffic, it will defer the allocation of other neighbors’ high-level traffic. We use Bayer’s [4] dynamic exponent to reduce holdoff time of SS, and speed up the exchange of control message. On the other hand, we design an “importance factor” (IM-factor) to score the importance of request. Through the exchange of IM-factor, SS and its neighbors will produce a threshold of IM-factor to filter the unimportant requests, and prevent minislot from being assigned too late. In our experiments, the proposed methods can reduce 85% delay and 20% jitter, and increase bandwidth utility by 7%. It shows that our method in reducing transmission delay is pratical and effective.

Approved for public release, distribution is unlimited / The purpose of this research was to introduce a Transformational Communications Architecture for the Unit Operations Center (UOC); Common Aviation Command and Control System (CAC2S); and Command and Control On-the- Move Network, Digital Over-the-Horizon Relay (CoNDOR). The methodology used was to conduct Field Tests with government contractors and private vendors in order to demonstrate the capabilities of each wireless technology researched. These wireless technologies, Free Space Optics (FSO), Microwave, 802.16, 802.11b over SecNet-11, Orthogonal Frequency Division Multiplexing (OFDM), Broadband Satellite, INMARSAT, and Iridium, all have the potential of being implemented in the transformational communications architecture for intra-nodal and inter-nodal links for UOC and CAC2S, as well as the CoNDOR communications architecture. The ultimate goal of this research was to introduce different technologies that offer more flexibility, mobility, and capability at the tactical level giving the Marine Corps the tactical wireless edge. Throughout this research, the focus revolved around testing equipment and network configurations in an IP network. Special consideration was given to wireless issues for the UOC, CAC2S, and CoNDOR, which could improve line-of-sight, beyond line-of-sight, and over-the-horizon communications for each program. These new technologies will transform communications in the United States Marine Corps for the 21st century. / Captain, United States Marine Corps

New and future telecommunication networks are and will be broadband type. The existing terrestrial and space radio communication infrastructures might be supplemented by new wireless networks that make and will make use of aeronautics-technology. Our study/contribution is referring to radio communications based on radio stations aboard a stratospheric platform named, by ITU-R, HAPS (High Altitude Platform Station). These new networks have been proposed as an alternative technology within the ITU framework to provide various narrow/broadband communication services. With the possibility of having a payload for Telecommunications in an aircraft or a balloon (HAPS), it can be carried out radio communications to provide backbone connections on ground and to access to broadband points for ground terminals. The latest implies a complex radio network planning. Therefore, the radio coverage analysis at outdoors and indoors becomes an important issue on the design of new radio systems. In this doctoral thesis, the contribution is related to the HAPS application for terrestrial fixed broadband communications. HAPS was hypothesised as a quasi-static platform with height above ground at the so-called stratospheric layer. Latter contribution was fulfilled by approaching via simulations the outdoor-indoor coverage with a simple efficient computational model at downlink mode. This work was assessing the ITU-R recommendations at bands recognised for the HAPS-based networks. It was contemplated the possibility of operating around 2 GHz (1820 MHz, specifically) because this band is recognised as an alternative for HAPS networks that can provide IMT-2000 and IMT-Advanced services. The global broadband radio communication model was composed of three parts: transmitter, channel, and receiver. The transmitter and receiver parts were based on the specifications of the IEEE Std 802.16TM-2009 (with its respective digital transmission techniques for a robust-reliable link), and the channel was subjected to the analysis of radio modelling at the level of HAPS and terrestrial (outdoors plus indoors) parts. For the channel modelling was used the two-state characterisation (physical situations associated with the transmitted/received signals), the state-oriented channel modelling. One of the channel-state contemplated the environmental transmission situation defined by a direct path between transmitter and receiver, and the remaining one regarded the conditions of shadowing. These states were dependent on the elevation angle related to the ray-tracing analysis: within the propagation environment, it was considered that a representative portion of the total energy of the signal was received by a direct or diffracted wave, and the remaining power signal was coming by a specular wave, to last-mentioned waves (rays) were added the scattered and random rays that constituted the diffuse wave. At indoors case, the variations of the transmitted signal were also considering the following matters additionally: the building penetration, construction material, angle of incidence, floor height, position of terminal in the room, and indoor fading; also, these indoors radiocommunications presented different type of paths to reach the receiver: obscured LOS, no LOS (NLOS), and hard NLOS. The evaluation of the feasible performance for the HAPS-to-ground terminal was accomplished by means of thorough simulations. The outcomes of the experiment were presented in terms of BER vs. Eb/N0 plotting, getting significant positive conclusions for these kind of system as access network technology based on HAPS.

M. Tech. Electrical Engineering. / Proposes certain approaches aimed at improving handover from the users point of view, the benefits may include enhanced quality of service, avoidance of handover disruption and reduction of handover rate, irrespective of high traffic loads at the BSs.The proposed scheme improves the network performance by minimising the handover delay time and also enhancing the effective use of radio resources

Architecture et mécanismes de bout en bout pour les communications mobiles et sans fil dans l'Internet. La gestion performante de la mobilité et l'amélioration des performances des couches basses sont deux enjeux fondamentaux dans le contexte des réseaux sans fil. Cette thèse apporte des solutions originales et innovantes qui visent à répondre à ces deux problématiques empêchant à ce jour d'offrir des possibilités de communication performantes et sans couture aux usagers mobiles accédant à l'Internet via des réseaux d'accès locaux sans fil (WLAN). Ces solutions se distinguent en particulier par l'impact minimum qu'elles ont sur les protocoles standards de l'Internet (niveaux transport et réseau) ou de l'IEEE (niveaux physique et liaison de données). S'inscrivant dans les paradigmes de "bout en bout" et "cross-layer", notre architecture permet d'offrir des solutions efficaces pour la gestion de la mobilité : gestion de la localisation et des handover en particulier. En outre, nous montrons que notre approche permet également d'améliorer l'efficacité des transmissions ainsi que de résoudre efficacement plusieurs syndromes identifiés au sein de 802.11 tels que les anomalies de performance, l'iniquité entre les flux et l'absence de contrôle de débit entre la couche MAC et les couches supérieures. Cette thèse résout ces problèmes en combinant des modèles analytiques, des simulations et de réelles expérimentations. Ces mécanismes adaptatifs ont été développés et intégrés dans une architecture de communication qui fournit des services de communication à haute performance pour réseaux sans fils tels que WIFI et WIMAX. / Wireless networks, because of the potential pervasive and mobile communication services they offer, are becoming the dominant Internet access networks. However, the legacy Internet protocols, still dominant at that time, have not been designed with mobility and wireless in mind. Therefore, numerous maladjustments and “defaults of impedance” can be observed when combining wireless physical and MAC layers with the traditional upper layers. This thesis proposes several solutions for a pacific coexistence between these communication layers that have been defined and designed independently. Reliable mobility management and Low layer performance enhancements are two main challenging issues in the context of wireless networks. Mobility management (which is mostly based on mobile IP architecture nowadays) aims to continuously assign and control the wireless connections of mobile nodes amongst a space of wireless access networks. Low layer performance enhancements mainly focus on the transmission efficiency such as higher rate, lower loss, interference avoidance. This thesis addresses these two important issues from an original and innovative approach that, conversely to the traditional contributions, entails a minimum impact on the legacy protocols and internet infrastructure. Following the “end to end” and “cross layer” paradigms, we address and offer efficient and light solutions to fast handover, location management and continuous connection support through a space of wireless networks. Moreover, we show that such an approach makes it possible to enhance transmission efficiency and solve efficiently several syndromes that plague the performances of current wireless networks such as performance anomaly, unfairness issues and maladjustment between MAC layer and upper layers. This thesis tackles these issues by combining analytical models, simulations and real experiments. The resulting mechanisms have been developed and integrated into adaptive mobility management communication architecture that delivers high performing communication services to mobile wireless systems, with a focus on WIFI and WIMAX access networks.

An abstract of the thesis of Bosi Chen for the Master of Science in Electrical and Computer Engineering presented Aug 1st, 2012. Title: Spectrum Regrowth for OFDM-based LTE and WiMAX Systems. In OFDM-based (Orthogonal Frequency Dimension Multiplexing) LTE (Long Term Evolution) and WiMAX (Worldwide Interoperability for Microwave Access) Systems, one of the critical components is the RF power amplifier. With current technologies, RF power amplifiers are not perfectly linear. The nonlinearity of an RF power amplifier is one of the main concerns in RF power amplifier design. The nonlinearity control is described by the out-of-band power emission levels, and the nonlinearity of an RF power amplifier is usually described by IP3 (the third-order intercept point). However, there is need of a clear relationship or expression between the out-of-band power emission level and IP3 for LTE and WiMAX Systems, which helps the RF designers to choose components. This thesis presents the analysis of the nonlinear effect of an RF amplifier in LTE and WiMAX Systems, and the derivation of the expressions for the estimated out-of-band emission levels for LTE and WiMAX signals in terms of IP3 and the power level of the signal. The result will be helpful for RF engineers in the design and test of RF power amplifiers in LTE and WiMAX Systems.

Given the current developments and advances in the scientific and technological aspects of human knowledge and introducing new approaches in various fields of telecommunication technologies and industries, there has been an increasing growth in its players¿ plans and a positive change in their outlooks in order to achieve the target of "anywhere and anytime access". Recent developments of WiMAX (Worldwide interoperability for Microwave Access) networks, as a sign of increasing needs and demands for new telecommunication services and capabilities, have led to revolutions in global telecommunication which should be perceived properly in terms of the commercial and technical aspects in order to enjoy the new opportunities. Most experts believe that WiMAX technology is a preliminary step to develop Fourth Generation networks known as 4G technologies. It has not only succeeded in the utilization of several of the latest telecommunication techniques in the form of unique practical standards, but also paved the way for the quantitative and qualitative developments of high-speed broadband access. IEEE 802.16 Standard introduces several advantages, and one of them is the support for Quality of Services (QoS) at the Media Access Control (MAC) level. For these purposes, the standard defines several scheduling classes at MAC layer to treat service flow in a different way, depending on QoS requirements. In this thesis, we have proposed a new QoS framework for Point-to-Multi Point (PMP) 802.16 systems operating in Time Division Duplexing (TDD) mode over a WirelessMAN-OFDM physical layer. The proposed framework consists of a Call Admission Control (CAC) module and a scheduling scheme for the uplink traffic as well as a simple frame allocation scheme. The proposed CAC module interacts with the uplink scheduler status and it makes its decision based on the scheduler queue status; on the other hand, the proposed scheduling scheme for the uplink traffic aims to support realtime flows and adapts the frame-by-frame allocations to the current needs of the connections, with respect to the grants boundaries fixed by the CAC module. Extensive OPNET simulation demonstrates the effectiveness of the proposed architecture.

En la presente tesis se plantea el diseño de una red WIMAX para el valle de Churín- Lima, para una operadora existente que quiere ofrecer sus servicios con dicha red. En este diseño se toma en cuenta no sólo a la población que habita el valle, sino también a aquellas que visitan con frecuencia el mismo. La tesis está estructurada de la siguiente manera: En el capítulo 1 se analiza la situación y problemática actual tanto en la provincia a la cual pertenece Churín, al valle en mención y porqué se desea insertar este diseño a Churín. En el capítulo 2 se muestra el marco teórico, donde se detallan los conceptos involucrados con la “Interoperabilidad mundial para acceso por microondas” (WIMAX) en su versión fija. En el capítulo 3 se realiza un análisis de demanda del mercado WIMAX para el valle de Churín, para de esta manera identificar a los potenciales clientes y los tipos de servicios a ofrecer. En el capítulo 4 se realiza la Ingeniería del Proyecto, donde se calcula la cantidad de estaciones Base a utilizar en la red, la topología de la misma, la red de transporte, la red de acceso, la infraestructura y equipos a emplear para la misma. Finalmente, en el capítulo 5 se evalúa el costo-beneficio de implementar esta red mediante el análisis del CAPEX Y OPEX, así como del VAN y el TIR.

Le développement et la prolifération des réseaux sans fil a contribué à l’évolution de notre quotidien. Toute cette multitude de technologies sans fil existantes permet, malgré sa complexité, d’offrir aux utilisateurs des services diversifiés, voix et données, de la manière la plus convenable, tout en permettant l’ubiquité des services dans une optique ABC (Always Best Connected). Ces réseaux utilisent des technologies différentes, mais en même temps, offrent des caractéristiques complémentaires. Ainsi, ce point s’avère attrayant dans la mesure où nous pourrons bénéficier des avantages de chacune des technologies en les interconnectant toutes afin de former un large réseau hétérogène. La mobilité, ou plus particulièrement la relève, que nous nous proposons d’étudier dans ce mémoire s’impose comme axe de recherche intéressant, et encore plus complexe dans un environnement hétérogène. Dans ce mémoire, deux architectures interconnectant un réseau UMTS et un autre Wimax ont été présentées. Plus précisément, nous avons mis l’emphase sur la procédure de relève verticale lors du passage de l’utilisateur d’un réseau Wimax à un réseau UMTS. Chacune des deux architectures utilise un protocole pour la gestion de la mobilité, en l’occurrence le MIP (Mobile Internet Protocol) et le SIP (Session Initiation Protocol). Afin d’évaluer les deux procédures, nous nous sommes donnés deux indicateurs, notamment le coût de signalisation et la durée de la procédure de relève verticale. Pour ce faire, nous avons spécifié un diagramme d’échanges des messages de signalisation propre à chacun des scénarios, un basé sur le MIP et l’autre basé sur le SIP. Ensuite, nous avons établi des expressions pour chacun des deux indicateurs précédemment cités qui ont été implémentées sous MATLAB. Les résultats démontrent que, généralement, le scénario de relève verticale basé sur le MIP présente une durée et un coût de signalisation moins élevé que celui basé sur le protocole SIP. / The development and proliferation of wireless networks has contributed to the evolution of our daily lives. Mobile users can move between heterogeneous networks, using terminals with multiple access interfaces. Thus, the most important issue in such environment is the Always Best Connected (ABC) concept allowing the best connectivity to applications anywhere at anytime. To answer ABC requirement, various vertical handover decision strategies have been proposed using advanced tools and proven concepts. In this paper, two architectures interconnecting a UMTS network and another Wimax have been presented. Each architecture uses a protocol for mobility management, namely MIP and SIP. To evaluate the two procedures, we are given two indicators, the signaling cost and the vertical handover delay. To evaluate our scenarios, we have established a specified signaling messages flow diagram specific to each scenario, one based on the MIP and the other based on the SIP. Then, we have given expressions for each of the two indicators mentioned above that we have implemented in MATLAB. The results show that, generally, the scenario based on MIP has lower signaling cost and delay than the scenario based on SIP.

Approved for public release, distribution is unlimited / Wireless mesh networking has emerged as the successor of the traditional ad hoc networks. New technological advances, the standardization of protocols and interfaces and the maturity of key components have made it possible for current mesh research groups to set goals that are really close to the world's expectations. The objective of this research is to design and implement a simulation toolkit for wireless mesh clusters that can be used as an additional performance evaluation technique for the Tactical Network Topology program of Naval Postgraduate School. This toolkit is implemented in the OPNET simulation environment and it incorporates various nodes running different ad hoc routing protocols. Furthermore, the investigation of a suitable combination of protocols for the Tactical Network Topology is achieved by creating scenarios and running a number of simulations using the mesh toolkit. / Captain, Hellenic Air Force