Results of the investigation has been presented to derive digital elevation models of forest areas for the determination of the parallax measuring accuracy from AATE (Adaptive Automatic Terrian Extraction) with the PCI software Geomatica. It has been used the informations from the threefold overlaps of aerial stereoscopic pairs. The parallax measuring errors on forest areas are three times larger than on the arable and pasturelands. It has been shown that the third dimension can be used for the derivative of crown of tree profiles and their roughness and the rates of timber growth can be derived with sufficiently high accuracy from the repeatability flying.

No description available.

No description available.

<p>Converting wood into paper is a complex process involving many different stages, one of which is pulping. Pulping involves liberating the wood fibres from each other, which can be done either chemically or mechanically. This thesis focuses on the most common chemical pulping method, the kraft cooking process, and especially on a recently developed improvement of the impregnation phase, which is the first part of a kraft cook.</p><p>Extended impregnation kraft cooking (EIC) technique is demonstrated to be an improvement of the kraft pulping process and provides a way to utilize softwood to a higher degree, at higher pulp yield. We demonstrate that it is possible to produce softwood (<em>Picea abies</em>) kraft pulp using a new cooking technique, resulting in a pulp that can be defibrated without inline refining at as high lignin content as 8% on wood, measured as kappa numbers above 90. Lignin is the wood constituent that holds the wood fibres together in the wood matrix. The new cooking technique uses the differences in reaction rate between the diffusion and consumption of hydroxide ions; it is used to ensure a homogenous impregnation of wood chips at lower impregnation temperatures and longer impregnation times than are generally used in the industry. The applied cooking temperatures are also substantially lower than those used in conventional kraft pulping systems, promoting uniform delignification. This results in a narrower kappa number distribution than in lab-cooked conventional kraft pulp.</p><p>High-kappa-number pulps were investigated for pulp sheet properties such as tensile strength, tensile stiffness, and compression strength. It was demonstrated that an EIC pulp of kappa number 95 has strength properties comparable to those of a conventional pulp of kappa number 82. Comparing the effects of starch multilayers on conventional and EIC pulps reveals similar effects. The use of the starch multilayer treatment increased the tensile index and decreased the tensile stiffness and short-span compression test (SCT) indices.</p><p>The EIC technique has also been used to produce a series of bleachable-grade pulps. The results indicate the possibility of increasing the lignin content of the pulp entering the oxygen delignification stage, since the reject content of gently defibered pulp is lower than 0.1% at kappa number 49.</p><p>In this thesis, we recommend that wood chips be impregnated for 2 h at 110 °C to neutralize acidic compounds in the wood and impregnate the chips with cooking chemicals, and that the ensuing cook be performed at 135–140 °C, depending on the target kappa number. We also recommend increasing the available amounts of cooking chemicals in the impregnation stage by using a higher liquor-to-wood ratio and keeping the alkali profile fairly high in the ensuing cook. This concept will reduce the amount of reject material, increase the pulping uniformity, and increase the selectivity towards lignin degradation in the kraft cook.</p> / <p>Omvandling av ved till papper är en komplicerad process som består av många olika steg där ett är massaframställningen (eng. <em>pulping</em>). Massaframställning medför att vedfibrerna frigörs från varandra på kemisk eller mekanisk väg. Denna avhandling fokuserar på den vanligaste kemiska metoden, sulfatkokning och speciellt den nyligen utvecklade förbättringen av impregnerings fasen, som är den första delen av ett sulfatkok. <em></em></p><p>Här visas att<em> Extended Impregnation kraft Cooking </em>(EIC) innebär en förbättring av sulfatkokningen och ett sätt att uppnå högre vedutnyttjande vid högre utbyte för barrved. Vi visar att det är möjligt att producera barrvedsmassa med en ny kokningsprincip som resulterar i en massa som är defibrerbar utan inline-raffinering vid så högt lignin innehåll som 8% (på ved), mätt som kappatal över 90. Lignin är den vedkomponent som håller ihop vedfibrerna i vedmatrisen. Kokningsprincipen utnyttjar skillnaderna i reaktionshastighet mellan diffusion och konsumtion av hydroxidjoner och nyttjas till att skapa en homogen impregnering av vedflisen vid lägre impregneringstemperatur och under längre tid än vad som vanligen används i industrin. De använda koktemperaturerna är också betydligt lägre än vid konventionell sulfatkokning vilket gynnar jämn delignifiering. Detta resulterar i en smalare kappatalsfördelning jämfört med laboratoriekokade konventionella massor.</p><p>Massor med höga kappatal undersöktes med avseende på egenskaper hos handark, såsom dragstyrka, dragstyvhet och kompressionsstyrka Det visades att handark från EIC massa vid kappatal 95 hade jämförbara styrkeegenskaper med konventionell massa vid kappatal 82. Vid jämförelse av effekten av stärkelse multilager på konventionella och EIC massor avslöjar liknande effekter. Användningen av stärkelsemultilager ökade dragindex och minskade dragstyvhets- och kompressions index (SCT, short-compression test).</p><p>Kokprincipen har även använts för att ta fram en serie blekbara massor. Resultaten visar på möjligheten att öka lignininnehållet i massan in till i syrgasdelignifierings-steget eftersom spetinnehållet för milt defibrerad massa var lägre än 0,1% vid kappatal 49.</p><p>I den här avhandlingen rekommenderar vi att vedflis impregneras i 2 timmar vid 110 °C för att neutralisera sura komponenter i veden och impregnera flisen med kokkemikalier, samt att utföra det efterföljande koket vid 135–140 °C beroende på önskat kappatal. Vi rekommenderar även att öka den tillgängliga mängden kokkemikalier i impregneringssteget genom att använda högre vätske-ved förhållande och att hålla alkali profilen relativt hög i det efterföljande koket. Detta koncept reducerar spetmängden, ger jämnare kokning och ökar selektiviteten för nedbrytning av lignin i sulfatkoket.</p>

Le diabète de type 2 est une maladie chronique dont l’incidence est en augmentation continuelle. Le risque de développer le diabète de type 2 chez les populations autochtones du Canada est de trois à cinq fois plus élevé que le reste de la population canadienne. La forêt boréale comporte plusieurs plantes médicinales ayant un potentiel pour le traitement ou la prévention du diabète. Certaines de ces plantes font partie de la médecine traditionnelle et alternative Crie. Des enquêtes ethnobotaniques ont amené notre équipe de recherche à identifier 17 extraits de plantes médicinales utilisées par les Cris d’Eeyou Istchee (Baie James, Québec) pour traiter les symptômes du diabète. Parmi ces extraits, certains ont montré des activités anti-diabétiques au niveau des cellules musculaires, des adipocytes et dans des études in vivo réalisées chez des animaux. Le but de cette thèse est d’élucider l’effet de ces 17 plantes sur l’homéostasie hépatique de glucose, d’identifier l’espèce la plus prometteuse et isoler ces constituants actifs. De même, le bleuet nain du genre Vaccinium angustifolium fait partie de la forêt boréale canadienne et est connu pour ses activités anti-diabétiques. Une biotransformation du jus de bleuet lui confère une activité antioxydante accrue et un profil biologique différent. Le deuxième but de cette thèse est d’élucider les mécanismes d’action par lesquels le jus de bleuet biotransformé (BJ) exerce son effet anti-diabétique et d’identifier ses principes actifs. Les résultats ont montré que trois extraits de plantes Cris se sont démarqués par leur effet sur l’homéostasie hépatique de glucose. Picea glauca exerce son effet en diminuant la production de glucose alors que Larix laricina agit en augmentant le stockage de glucose. Abies balsamea a montré le profil le plus prometteur, elle agit simultanément en diminuant l’activité de la Glucose-6-phosphatase (G6Pase) via la stimulation des voies insulino-dépendante et - indépendante et en augmentant l’activité de la Glycogène synthétase (GS) suite à la phosphorylation de la Glycogène synthase kinase-3. Le fractionnement de l’extrait d’Abies balsamea guidé par les deux bioessais a mené à l’isolation de trois composés actifs; l’acide abiétique (AA), l’acide déhydroabiétique (DAA) et le squalène (SQ). Les principes actifs ont montré le même mécanisme d’action que l’extrait brut en diminuant l’activité de la G6Pase et augmentant celle de la GS ainsi qu’en activant les voies de signalisation impliquées. Le DAA ii s’est démarqué par son effet le plus puissant et très comparable à celui de l’extrait d’Abies balsamea dans toutes les expériences. De son côté le BJ a montré un effet sur la diminution de la production hépatique de glucose, l’augmentation de son stockage ainsi que l’augmentation de son transport dans le muscle. Son fractionnement guidé par les bioessais a permis d’isoler sept fractions dont trois étaient les plus actives. L’identification des constituants de ces fractions actives a mené à isoler quatres composés phénoliques; l’acide chlorogénique, l’acide gallique, l’acide protocatéchique et le catéchol. Le catéchol s’est démarqué avec ses effets les plus puissants en diminuant l’activité de la G6Pase, augmentant celle de la GS et en stimulant le transport de glucose dans le muscle. Les résultats de cette thèse indiquent que la diminution de la production hépatique de glucose peut s’ajouter au profil anti-diabétique de certaines plantes médicinales Cries et surtout à celui d’A.balsamea dont les composés actifs peuvent aider dans le développement de nouvelles molécules anti-diabétiques. De plus, les résultats de cette thèse ont montré que l’activité antidiabétique du BJ implique le contrôle de l’homéostasie de glucose au niveau du foie et du muscle. L’identification du catéchol comme principe actif avec potentiel anti-diabétique prometteur pourra servir pour des fins thérapeutiques ultérieures. / Type 2 diabetes is a chronic disease for which incidence is continuously increasing. The risk of developing type 2 diabetes among Aboriginal people in Canada is three to five times higher than the rest of the Canadian population. The boreal forest has several medicinal plants with potential for the treatment or prevention of diabetes. Some of these plants are part of the Cree traditional and alternative medicine. Ethnobotanical surveys led our research team to identify 17 medicinal plant extracts used by the Crees of Eeyou Istchee (James Bay, Quebec) to treat symptoms of diabetes. Some extracts showed anti-diabetic activities in muscle cells, adipocytes and in vivo studies in animals. The aim of this thesis is to elucidate the effect of these 17 plants on hepatic glucose homeostasis, to identify the most promising species and isolate its active constituents. Similarly, Canadian lowbush blueberry, Vaccinium angustifolium.Ait, is part of the Canadian boreal forest and is known for its anti-diabetic activities. Biotransformation of blueberry juice gives it an increased antioxidant activity and a different biological profile. The second aim of this thesis is to elucidate the mechanisms of action by which biotransformed blueberry juice (BJ) exerts its anti-diabetic effect and identify its active constituents. The results showed that three Cree plants stood out with their effect on hepatic glucose homeostasis. Picea glauca exerts its effect by reducing glucose production whereas Larix laricina works by increasing its the storage. Abies balsamea showed the most promising profile, simultaneously and powerfully reducing glucose-6-phosphatase (G6Pase) involving both insulin-dependent and -independent pathways and stimulating Glycogen synthase (GS) via phosphorylation of Glycogen synthase kinase-3 (GSK-3). Bioassay-guided fractionation of Abies balsamea led to the isolation of three active compounds; Abietic acid (AA), dehydroabietic acid (DAA) and squalene (SQ). The active constituents have shown the same mechanism of action as the crude extract by decreasing the activity of G6Pase, increasing that of the GS and activating signaling pathways. DAA stood out for its most powerful effect close to that of the crude extract in all experiments. Our results showed that anti-diabetic activity of BJ involves decrease in hepatic glucose production, increase of storage and enhancement of glucose uptake in muscle. Its bioassayiv guided fractionation led to isolate seven fractions, three of which were the most active. Identification of components in the active fractions resulted in four isolated phenolic compounds; chlorogenic acid, gallic acid, protocatechuic acid and catechol. Catechol stood out with its most powerful effects by decreasing the activity of G6Pase, increasing the GS and stimulating glucose transport in muscle. Our results thus confirm that the reduction of hepatic glucose production likely contributes to the therapeutic potential of several anti-diabetic Cree traditional plant and especially that of Abies balsamea whose active compounds may help in the development of new anti-diabetic molecules. In addition, the results of this thesis showed that the anti-diabetic activity of BJ involves control of glucose homeostasis in the liver and muscle. Identification of catechol as an active compound with anti-diabetic promising potential can be used for future therapeutic purposes.

Understanding of carbon cycling in coniferous forests that represent a large carbon sink is crucial for our understanding of natural processes under global climate change. Recognition of fungi as fundamental decomposers can contribute to this understanding. Fungi are able to decompose numbers of substrates and possess a variety of enzymes to do so In this study I present litter decomposing fungi in mountain spruce forest from national park Šumava. The aim of my thesis was to follow succession and community changes of fungi from the early stages of decomposition of Picea abies needles until degradation of organic matter in the organic horizon of the soil. This aim was accomplished partly by recording the extracellular enzyme production of fungi in different stages of decomposition from needles attached to the twigs of a fallen tree to a litter material in later stages of decomposition on the soil surface. In addition to testing of fungi on their natural substrata - needle litter, enzyme activities were also measured in laboratory agar cultures, which allow comparison of diverse fungi with different origins. Enzyme activities were aimed at enzymes decomposing cellulose and compounds found in litter. Although ecology of endophytic and saprothrophic fungi suggest differences in enzyme production, these...

Mechanical pulps are used in paper products such as magazine or news grade printing papers or paperboard. Mechanical pulping gives a high yield; nearly everything in the tree except the bark is used in the paper. This means that mechanical pulping consumes much less wood than chemical pulping, especially to produce a unit area of printing surface. A drawback of mechanical pulp production is the high amounts of electrical energy needed to separate and refine the fibers to a given fiber quality. Mechanical pulps are often produced from slow growing spruce trees of forests in the northern hemisphere resulting in long, slender fibers that are well suited for mechanical pulp products. These fibers have large varieties in geometry, mainly wall thickness and width, depending on seasonal variations and growth conditions. Earlywood fibers typically have thin walls and latewood fibers thick. The background to this study was that a more detailed fiber characterization involving evaluations of distributions of fiber characteristics, may give improved possibilities to optimize the mechanical pulping process and thereby reduce the total electric energy needed to reach a given quality of the pulp and final product. This would result in improved competitiveness as well as less environmental impact. This study evaluated the relation between fiber characteristics in three types of mechanical pulps made from Norway spruce (Picea abies), thermomechanical pulp(TMP), stone groundwood pulp (SGW) and chemithermomechanical pulp (CTMP). In addition, the influence of fibers from these pulp types on sheet characteristics, mainly tensile index, was studied. A comparatively rapid method was presented on how to evaluate the propensity of each fiber to form sheets of high tensile index, by the use of raw data from a commercially available fiber analyzer (FiberLabTM). The developed method gives novel opportunities of evaluating the effect on the fibers of each stage in the mechanical pulping process and has a potential to be applied also on‐line to steer the refining and pulping process by the characteristics of the final pulp and the quality of the final paper. The long fiber fraction is important for the properties of the whole pulp. It was found that fiber wall thickness and external fibrillation were the fibercharacteristics that contributed the most to tensile index of the long fiber fractions in five mechanical pulps (three TMPs, one SGW, one CTMP). The tensile index of handsheets of the long fiber fractions could be predicted by linear regressions using a combination of fiber wall thickness and degree of external fibrillation. The predicted tensile index was denoted BIN, short for Bonding ability INfluence. This resulted in the same linear correlation between BIN and tensile index for 52 samples of the five mechanical pulps studied, each fractionated into five streams(plus feed) in full size hydrocyclones. The Bauer McNett P16/R30 (passed 16 meshwire, retained on a 30 mesh wire) and P30/R50 fractions of each stream were used for the evaluation. The fibers of the SGW had thicker walls and a higher degree of external fibrillation than the TMPs and CTMP, which resulted in a correlation between BIN and tensile index on a different level for the P30/R50 fraction of SGW than the other pulp samples. A BIN model based on averages weighted by each fiber´s wall volume instead of arithmetic averages, took the fiber wall thickness of the SGW into account, and gave one uniform correlation between BIN and tensile index for all pulp samples (12 samples for constructing the model, 46 for validatingit). If the BIN model is used for predicting averages of the tensile index of a sheet, a model based on wall volume weighted data is recommended. To be able to produce BIN distributions where the influence of the length or wall volume of each fiber is taken into account, the BIN model is currently based on arithmetic averages of fiber wall thickness and fibrillation. Fiber width used as a single factor reduced the accuracy of the BIN model. Wall volume weighted averages of fiber width also resulted in a completely changed ranking of the five hydrocyclone streams compared to arithmetic, for two of thefive pulps. This was not seen when fiber width was combined with fiber wallthickness into the factor “collapse resistance index”. In order to avoid too high influence of fiber wall thickness and until the influence of fiber width on BIN and the measurement of fiber width is further evaluated, it is recommended to use length weighted or arithmetic distributions of BIN and other fiber characteristics. A comparably fast method to evaluate the distribution of fiber wall thickness and degree of external fibrillation with high resolution showed that the fiber wallthickness of the latewood fibers was reduced by increasing the refining energy in adouble disc refiner operated at four levels of specific energy input in a commercial TMP production line. This was expected but could not be seen by the use of average values, it was concluded that fiber characteristics in many cases should be evaluated as distributions and not only as averages. BIN distributions of various types of mechanical pulps from Norway spruce showed results that were expected based on knowledge of the particular pulps and processes. Measurements of mixtures of a news‐ and a SC (super calendered) gradeTMP, showed a gradual increase in high‐BIN fibers with higher amounts of SCgrade TMP. The BIN distributions also revealed differences between the pulps that were not seen from average fiber values, for example that the shape of the BINdistributions was similar for two pulps that originated from conical disc refiners, a news grade TMP and the board grade CTMP, although the distributions were on different BIN levels. The SC grade TMP and the SC grade SGW had similar levels of tensile index, but the SGW contained some fibers of very low BIN values which may influence the characteristics of the final paper, for example strength, surface and structure. This shows that the BIN model has the potential of being applied on either the whole or parts of a papermaking process based on mechanical or chemimechanical pulping; the evaluation of distributions of fiber characteristics can contribute to increased knowledge about the process and opportunities to optimize it.

This thesis is focused on environmental preferences of wood-decaying fungi and their relationships with forest structure and development. Relationships of fungi to properties of wood and forest stands were studied on the basis of field observations in Central-European mountain spruce forests. Plot-based approach was used to reveal a general pattern in the diversity of fungi within a single forest stand and between different stands. The analysis of stand structure provided a background for plot-based approach. Substrate-based approach was used to study single species preferences and their communities. In addition, the influence of wood properties (including fungi and their rots) on the regeneration of spruce on logs was studied.

This thesis is focused on application methods of dendrochronology on various ecological and historical aspects of forest communities, human management practices, and historical utilization of wood. Studies revealed growth responses of trees in various type of forest vegetation represented by spruce forest, alder carr and alluvial forests and involved autochthonous tree species with all morphological types of wood. These works demonstrated necessity of dynamic evolving of the regional chronologies for the Czech Republic.

KUBÍNOVÁ, Zuzana. The effect of elevated CO2 concentration and irradiation on quantitative parameters of mesophyll cells of Norway spruce. Prague, 2010. 74 p. Master's degree thesis. Faculty of Science, Charles University in Prague. Abstract The aim of the present thesis was to choose and adjust a suitable methodology for counting particles in 3D space, which would be suitable for unbiased estimation of chloroplast number in needle mesophyll cells. The disector method was used for the first time to determine the number of chloroplasts. This method enables unbiased estimation of chloroplast number in needle volume from optical sections captured from fresh free-hand sections by confocal microscope. The sections did not need any pre-processing. Another aim was to compare selected photosynthetic and anatomical characteristics of sun and shade Norway spruce needles, which were grown under different CO2 concentration. The trees were grown for eight years in ambient (during the experiment increasing from 357 up to 370 µmol CO2 ∙ mol-1 ) CO2 concentration or elevated (700 µmol ∙ mol-1 ) CO2 concentration in special glass domes on an experimental research site of the Institute of Systems Biology and Ecology, Academy of Sciences of the Czech Republic at Bílý Kříž in Moravskoslezské Beskydy mountains. The sun needles...