Controlled radical polymerization (CRP) can be viewed as the middle ground between living anionic polymerization (LAP) and conventional free radical polymerization (FRP). It combines the precise control over polymer structure offered by LAP, under a tolerant reaction condition similar to FRP. One of the most studied CRP is atom transfer radical polymerization (ATRP), with over 10,000 papers published since its introduction in 1995. Despite the numerous studies, knowledge on its fundamental mechanism is still lacking, as evident from the lack of expression for full MWD and polydispersity that account for termination reaction. Since termination is unavoidable in ATRP, the existing expressions give inaccurate predictions as dead chains accumulate. In this study, we derived expressions for full MWD at low conversion and for polydispersity. These expressions allow us to quantify and gain better understanding on the contribution of termination. In addition, the resulting polydispersity expression shows better agreement than the existing equation when correlated with experiment data. In addition to the aforementioned questions, there are also controversies regarding the kinetics of surface-initiated ATRP, with researchers divided into two schools of theories. We evaluated the validity of these theories by comparing their predictions to experimental trends. Both theories were found to be inadequate in explaining all the experimental observations, thus triggering an investigation of the graft density. Graft density is an important determining property for polymer brushes, yet little is known about what affects its final value. Through simulations, we investigated the effect of experiment factors on the grafting density. A decrease in the amount of deactivator is found to decrease the grafting density, which could be explained by an increase in the number of monomers added per activation cycle. This knowledge allows us to explain the conflicting experiment observations regarding the growth trends of polymer layers reported in the literatures. / Thesis / Doctor of Philosophy (PhD) / Polymer materials are used almost everywhere in our daily life from clothing to water bottle. This wide range of applications owes to the nearly infinite possible properties that polymer can possess. Different polymerization processes to synthesize polymers have their own weaknesses and strengths. Herein we investigated the fundamental mechanism of one of the currently most attractive polymerization systems, atom transfer radical polymerization (ATRP). This process allows the synthesis of polymers with precisely tailored chain microstructures, making it possible to create polymer with sophisticated properties. Using modeling approaches, we derived explicit expressions for determining chain properties, allowing detailed investigation of how various factors affect these properties. Through these investigations, we obtained better understanding on the mechanism of ATRP in solution and on surface. This knowledge is crucial in providing insight and guiding experimental designs for better control over the material properties.

Highly proton conducting polymers for operation in hydrogen/oxygen proton exchange membrane fuel cells (PEMFCs) provide often a poor mechanical strength due to high water contents. To strengthen the conducting polymers, blends with different ratios of partially fluorinated sulfonic acid graft and diblock copolymers with perfluorinated polymers were prepared. To analyze the effect of the different quantities of the compounds, with regard to water sorption and proton conducting properties, membranes were prepared by dissolving the components and drop casting. Partially sulfonated poly([vinylidene difluoride-co-chlorotrifluoroethylene]-g-styrene) (P(VDF-co-CTFE)-g-SPS) was blended with polyvinylidene difluoride (PVDF), decreasing the ion exchange capacity (IEC). The blended polymers absorbed less water. However, the by AC impedance spectroscopy determined proton conductivity stayed stable or increased slightly. The effective proton mobility remained constant. Partially sulfonated poly([vinylidene difluoride-co-hexafluoropropylene]-b-styrene) (P(VDF-co-HFP)-b-SPS) with two different PS-block lengths were blended with different amounts of poly(vinylidene difluoride-co-hexafluoropropylene) (P(VDF-co-HFP)). In that case, the polymers absorbed less water and the proton conductivity decreased stepwise by adding more than 20 wt% P(VDF-co-HFP). The results indicate that a blending of P(VDF-co-CTFE)-g-SPS with PVDF inhibits swelling without having an effect on the proton conductivity, though water sorption and IEC are reduced.

Highly proton conducting polymers for operation in hydrogen/oxygen proton exchange membrane fuel cells (PEMFCs) provide often a poor mechanical strength due to high water contents. To strengthen the conducting polymers, blends with different ratios of partially fluorinated sulfonic acid graft and diblock copolymers with perfluorinated polymers were prepared. To analyze the effect of the different quantities of the compounds, with regard to water sorption and proton conducting properties, membranes were prepared by dissolving the components and drop casting. Partially sulfonated poly([vinylidene difluoride-co-chlorotrifluoroethylene]-g-styrene) (P(VDF-co-CTFE)-g-SPS) was blended with polyvinylidene difluoride (PVDF), decreasing the ion exchange capacity (IEC). The blended polymers absorbed less water. However, the by AC impedance spectroscopy determined proton conductivity stayed stable or increased slightly. The effective proton mobility remained constant. Partially sulfonated poly([vinylidene difluoride-co-hexafluoropropylene]-b-styrene) (P(VDF-co-HFP)-b-SPS) with two different PS-block lengths were blended with different amounts of poly(vinylidene difluoride-co-hexafluoropropylene) (P(VDF-co-HFP)). In that case, the polymers absorbed less water and the proton conductivity decreased stepwise by adding more than 20 wt% P(VDF-co-HFP). The results indicate that a blending of P(VDF-co-CTFE)-g-SPS with PVDF inhibits swelling without having an effect on the proton conductivity, though water sorption and IEC are reduced.:1 Introduction 2 Literature Review 2.1 Fuel Cells 2.1.1 Proton Exchange Membrane Fuel Cells 2.1.2 Other Types of Fuel Cells 2.2 Proton Conductivity 2.3 Proton Conducting Polymers 2.4 Impedance Spectroscopy 2.5 Polymers 2.6 Blending 2.7 Synthesis 2.7.1 Atom Transfer Radical Polymerization 2.7.2 Emulsion Polymerization 3 Results 3.1 Synthesis 3.1.1 Polyvinylidene Diuoride (PVDF) 3.1.2 Diblock Copolymers P(VDF-co-HFP)-b-SPS and Blends 3.1.3 Graft Copolymer P(VDF-co-HFP)-b-SPS Blends 3.2 Degree of Sulfonation 3.3 Ionomer Content 3.4 Ion Exchange Capacity 3.5 Water Content and Uptake 3.6 Proton Concentration 3.7 Watermolecules per Ionic Group 3.8 Proton Conductivity 3.9 Proton Mobility 4 Discussion & Conclusion 5 Experimental Part 5.1 Synthesis 5.1.1 Synthesis of PVDF 5.1.2 Synthesis of P(VDF-co-HFP)-b-PS 5.1.3 Sulfonation of the Polystyrene Block 5.2 Polymer Characterization 5.3 Membrane Preparation 5.4 Membrane Characterization Bibliography Appendix

Les polymères à empreintes moléculaires (MIP), également appelés "anticorps en plastique", sont des récepteurs biomimétiques synthétiques qui sont capables de reconnaître et lier une molécule cible avec une affinité et une spécificité comparables à celles des récepteurs naturels tels que des enzymes ou des anticorps. En effet, les MIP sont utilisés comme éléments de reconnaissance synthétiques dans les biocapteurs et biopuces pour la détection de petits analytes et les protéines. La technique d'impression moléculaire est basée sur la formation de cavités de reconnaissance spécifiques dans des matrices polymères par un procédé de moulage à l'échelle moléculaire. Pour la conception de capteurs et biopuces, une cinétique d'adsorption et une réponse du capteur rapide, l'intégration des polymères avec des transducteurs, et une haute sensibilité de détection sont parmi les principaux défis. Dans cette thèse, ces problèmes ont été abordés par le développement de nanocomposites MIP / d'or via le greffage du MIP sur les surfaces en utilisant des techniques de polymérisation dédiées comme l'ATRP qui est une technique de polymérisation radicalaire contrôlée (CRP). Ces techniques CRP sophistiquées sont en mesure d'améliorer considérablement les matériaux polymères. L'utilisation de l'ATRP dans le domaine de MIP a été limitée jusqu'à présent en raison de son incompatibilité inhérente avec des monomères acides comme l'acide méthacrylique (MAA), qui est de loin le monomère fonctionnel le plus largement utilisé dans les MIP. Ici, un nouveau procédé est décrit pour la synthèse de MIP par ATRP photo-initiée utilisant fac-[Ir(Ppy)3] comme catalyseur. La synthèse est possible à température ambiante et est compatible avec des monomères acides. Cette étude élargit considérablement la gamme de monomères fonctionnels et de molécules empreintes qui peuvent être utilisés lors de la synthèse de MIP par ATRP. La méthode proposée a été utilisée pour la fabrication de nanocomposites hiérarchiquement organisés sur des surfaces métalliques nanostructurés avec des nano-trous et nano-ilots, présentant des effets plasmoniques pour l'amplification du signal. La synthèse de films de MIP à l'échelle du nanomètre localisés sur la surface d'or a été démontrée. Des méthodes de transduction optiques, à savoir la résonance de plasmons de surface localisée (LSPR) et la spectroscopie Raman exaltée par effet de surface (SERS) ont été exploitées. Ces techniques se sont montrées prometteuses pour l'amélioration de la limite de détection dans la détection d'analytes biologiquement pertinents, y compris les protéines et le médicament propranolol. / Molecularly imprinted polymers (MIPs), also referred to as plastic antibodies, are synthetic biomimetic receptors that are able to bind target molecules with similar affinity and specificity as natural receptors such as enzymes or antibodies. Indeed, MIPs are used as synthetic recognition elements in biosensors and biochips for the detection of small analytes and proteins. The molecular imprinting technique is based on the formation of specific recognition cavities in polymer matrices by a templating process at the molecular level. For sensor and biochip development, fast binding kinetics of the MIP for a rapid sensor response, the integration of the polymers with transducers, and a high sensitivity of detection are among the main challenges. In this thesis, the above issues are addressed by developing MIP/gold nanocomposites by grafting MIPs on surfaces, using dedicated techniques like atom transfer radical polymerization (ATRP) which is a versatile controlled radical polymerization (CRP) technique. Theses ophisticated CRP techniques, are able to greatly improve the polymeric materials. The use of ATRP in the MIP field has been limited so far due to its inherent incompatibility with acidic monomers like methacrylic acid (MAA), which is by far the most widely used functional monomer. Herein, a new method is described for the MIP synthesis through photo-initiated ATRP using fac-[Ir(ppy)3] as ATRP catalyst. The synthesis is possible at room temperature and is compatible with acidic monomers. This study considerably widens the range of functional monomers and thus molecular templates that can be used when MIPs are synthesized by ATRP. The proposed method was used for fabrication of hierarchically organised nanocomposites based on MIPs and nanostructured metal surfaces containing nanoholes or nanoislands, exhibiting plasmonic effects for signal amplification. The fabrication of nanometer scale MIP coatings localized on gold surface was demonstrated. Optical transduction methods, namely Localized Surface Plasmon Resonance (LSPR) and Surface Enhanced Raman Spectroscopy (SERS) were exploited and shown that they hold great promise for enhancing the limit of detection in sensing of biologically relevant analytes including proteins and the drug propranolol.

Here, we report on a new temperature responsive polymer brush system with a terminal “click” functionality. Bifunctionalized poly(N-isopropylacrylamide) (PNiPAAm) with distinct functional end groups was synthesized by atom transfer radical polymerization (ATRP) and grafted to a modified silicon substrate. The presence of the active terminal alkyne functionality is validated using an azide-modified rhodamine B (N3-RhB) via copper(I) catalyzed alkyne–azide cycloaddition (CuAAC). The optical properties and swelling dynamics of an N3-RhB modified PNiPAAm brush are analyzed in dry state and in situ by VIS-spectroscopic ellipsometry (SE). The best-fit results are obtained using a Gaussian oscillator model and are confirmed by UV/VIS-spectroscopy. We observed evidence of interactions between the aromatic residues of the dye and the PNiPAAm amide groups, which significantly affect the swelling behavior of the modified polymer brush. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

Η δυνατότητα να συνδυαστούν οι ιδιότητες οργανικών και ανόργανων συστατικών σε ένα μοναδικό νανοδομημένο υβριδικό υλικό αποτελεί μία σημαντική επιστημονική πρόκληση στο σχεδιασμό υλικών, τα οποία μπορούν να εμφανίζουν νέες βελτιωμένες ιδιότητες και να τύχουν προηγμένων εφαρμογών. Τα υβριδικά υλικά, γενικά, μπορούν να ταξινομηθούν σε δύο μεγάλες κατηγορίες: στην κατηγορία I (class I), όπου οι δύο φάσεις συνδυάζονται μέσω ασθενών αλληλεπιδράσεων, και στην κατηγορία II (class II), όπου οι δύο φάσεις είναι σταθερά συνδεδεμένες. Στην παρούσα εργασία διερευνήθηκε η δυνατότητα εφαρμογής νανοδομημένων υβριδικών υλικών ως ετερογενείς καταλύτες στη διεργασία παραγωγής βιοντίζελ από διαφόρων ειδών έλαια. Κατά τη διεργασία αυτή, η οποία καλείται μετεστεροποίηση ή μεθανόλυση, τριγλυκερίδια αντιδρούν με μια αλκοόλη παρουσία ισχυρού οξέος ή βάσης προς παραγωγή εστέρων και γλυκερίνης. Σε πρώτη φάση, εστιάσαμε στη σύνθεση και το χαρακτηρισμό class I και class II υβριδικών οργανικών/ανόργανων υλικών αποτελούμενων από έναν ανόργανο πυρήνα διοξειδίου του πυριτίου (silica), ο οποίος θα περιβάλλεται από πολυμερικές αλυσίδες. Έτσι, στην προσπάθεια σύνθεσης υβριδικών υλικών class I αξιοποιήθηκαν οι πιθανές αλληλεπιδράσεις καθαρών και αμινοτροποποιημένων νανοσωματιδίων διοξειδίου του πυριτίου με υδατοδιαλυτά συμπολυμερή P(SSΗ-co-MA) του στυρενοσουλφονικού οξέος (SSH), με το μηλεϊνικό οξύ (ΜΑ), τα οποία φέρουν τόσο καρβοξυλικές όσο και σουλφονικές ομάδες. Ως αποτέλεσμα του όξινου χαρακτήρα των πολυμερών, τα υβριδικά νανοσωματίδια θα μπορούσαν δυνητικά να χρησιμοποιηθούν ως όξινοι καταλύτες κατά την παραγωγή του βιοντίζελ. Στην προσπάθεια σύνθεσης class II υβριδικών υλικών αξιοποιήθηκε κυρίως ο πολυμερισμός ελευθέρων ριζών μέσω μεταφοράς ατόμου (ATRP), μονομερών όπως στυρενοσουλφονικό νάτριο (SSNa), Ν-ισοπροπυλακρυλαμίδιο (NIPAM) και 2-(διμεθυλαμινο)μεθακρυλικός αιθυλεστέρας (DMAEMA). Για την εκκίνηση του πολυμερισμού χρησιμοποιήθηκαν νανοσωματίδια silica χημικά τροποποιημένα με 3-αμινοπροπυλοτριαιθοξυσιλάνιο και ακολούθως με 2-χλωροπροπιονυλοχλωρίδιο. Εναλλακτικά, χρησιμοποιήθηκαν νανοσωματίδια silica χημικά τροποποιημένα με 3-χλωροπροπυλoτριαιθοξυσιλάνιο (ATRP πολυμερισμός), ή βινυλοτριμεθοξυσιλανιο (πολυμερισμός ελευθέρων ριζών, FRP). Ο χαρακτηρισμός των δειγμάτων κατά περίπτωση έγινε με φασματοσκοπία πυρηνικού μαγνητικού συντονισμού υδρογόνου (1H NMR), φασματοσκοπία υπερύθρου με μετασχηματισμό Fourier (FTIR), θερμοσταθμική ανάλυση (TGA) και τιτλοδότηση οξέος-βάσεως. Στο τελευταίο μέρος της εργασίας ελέγχθηκε η καταλυτική δράση κάποιων εκ των συντεθέντων υλικών στην αντίδραση μεθανόλυσης της τριοξικής γλυκερόλης, χρησιμοποιώντας την τεχνική 1H NMR. Διαπιστώθηκε πως τα αμινοτροποποιημένα νανοσωματιδία silica εμφανίζουν σημαντική καταλυτική δράση. Αντίθετα η ικανότητα των υβριδικών οργανικών/ανόργανων υλικών silica-NH2(B)/P(SSH50-co-MA50), silica-NH2(D)/P(SSH75-co-MA25), και silica-VTMS-PDMAEMA να δρουν ως όξινοι ή βασικοί καταλύτες της ίδιας αντίδρασης είναι πολύ περιορισμένη. / The possibility to combine the properties of organic and inorganic components in a unique nanostructured hybrid material is a major scientific challenge in designing novel materials exhibiting improved properties and finding advanced applications. Hybrid materials generally can be classified into two categories: class I, where the two phases are combined through weak interactions, and class II, where the two phases are covalently connected. The aim of the present study was to develop novel hybrid organic/inorganic nanomaterials, potentially applied as heterogeneous catalysts in the biodiesel production process. In this process, called transesterification or methanolysis, triglycerides from various oils react with an alcohol in the presence of a strong acid or base to produce the respective esters and glycerin. In the first part of this work, we focused on the synthesis and characterization of class I and class II hybrid organic/inorganic nanomaterials consisting of an inorganic silicon dioxide (silica) core and a polymer shell. Thus, for the class I hybrid materials we took advantage of the weak interactions between net or amino-functionalized silica nanoparticles and water-soluble P(SSH-co-MA) copolymers of styrene sulfonic acid (SSH), with maleic acid (MA), carrying both carboxyl and sulfonic groups. These hybrid nanoparticles could potentially be used as acidic catalysts in the production of biodiesel, as a consequence of the acidic nature of the polymer used. For the class II hybrid materials, we mostly applied atom transfer radical polymerization (ATRP) of monomers such as sodium styrene sulfonate (SSNa), N-isopropylacrylamide (NIPAM) and 2-(dimethylamino) ethyl methacrylate (DMAEMA). To initiate the polymerization, silica nanoparticles chemically modified with 3-aminopropyltriethoxysilane and subsequently with 2-chloropropionylchloride were used. Alternatively, we also used silica nanoparticles chemically modified with 3-chloropropyltriethoxysilane (ATRP polymerization), or vinyltrimethoxysilane (free radical polymerization, FRP). In all cases, the products were characterized through a combination of techniques, such as proton nuclear magnetic resonance spectroscopy (1H NMR), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA) and acid-base titration. In the latter part of this work, the catalytic activity of some materials in the methanolysis process of glycerol triacetate was investigated, using the 1H NMR technique. It was found that the aminofunctionalized silica nanoparticles exhibit significant catalytic activity, whereas the ability of the hybrid materials silica-NH2(B)/P(SSH50-co-MA50), silica-NH2(D)/P(SSH75-co-MA25) and silica-VTMS-PDMAEMA to act as acidic or basic catalysts is very limited.

No description available.

The poly(glycidyl methacrylate)-modified magnetite nanoparticles, Fe3O4-PGMA NPs, were investigated and applied in nondestructive flaw detection of polymeric materials in this research. The Fe3O4 endowed magnetic property to the materials for flaw detection while the PGMA promoted colloidal stability and prevented particle aggregation. The magnetite nanoparticles (Fe3O4 NPs) were successfully synthesized by coprecipitation and then surface-modified with PGMA to form PGMA-modified Fe3O4 NPs by both grafting-from and grafting-to approaches. For the grafting-from approach, the Fe3O4 NPs were surface-functionalized with α-bromo isobutyryl bromide (BIBB) to form BIB-modified Fe3O4 NPs (Fe3O4-BIB NPs) with covalent linkage. The resultant Fe3O4-BIB NPs were used as surface-initiators to grow PGMA by surface-initiated atom transfer radical polymerization (SI-ATRP). For the grafting-to approach, the Fe3O4 NP were surface-functionalized with (3-mercaptopropyl)triethoxysilane (MCTES) to form MCTES-modified Fe3O4 NPs (Fe3O4-MCTES NPs). The PGMA with Br-end group was pre-synthesized by ATRP and then was grafted to the surface of the Fe3O4-MCTES NPs by coupling reaction. Both bare and modified Fe3O4 NPs exhibited superparamagnetism and the existence of iron oxide in the form of Fe3O4 was confirmed. The particle size of individual Fe3O4 NPs was about 8 – 24 nm but they aggregated to form clusters. The PGMA-modified NPs formed stable dispersion in chloroform and had larger cluster sizes than the unmodified ones because of the PGMA polymer layer. However, the uniformity of the NP clusters could be improved with PGMA surface grafting. The PGMA surface layer of the grafting-from (Fe3O4-gf-PGMA) NPs was thin and dense while that of the grafting-to (Fe3O4-gt-PGMA) NPs was thick and loose. The hydrodynamic diameters (Zave) of Fe3O4-gf-PGMA NP clusters could be controlled between 176 to 643 nm, dependent on the PGMA contents and reaction conditions. During SI-ATRP, side reactions happened and caused NP aggregation as well as increase of size of NP clusters. However, the aggregation has been minimized through optimization of reaction conditions. Oppositely, Zave values of Fe3O4-gt-PGMA NPs had little variation of about 120 – 190 nm. And the PGMA content of the Fe3O4-gt-PGMA NPs was limited to 12.5% because of the spatial hindrance during grafting process. The saturation magnetization (Ms) of the unmodified Fe3O4 NPs was about 77 emu/g, while those of the grafting-from and grafting-to Fe3O4-PGMA NPs were 50 – 66 emu/g and 63 – 70 emu/g, respectively. For Fe3O4-PGMA NPs with similar Fe3O4 contents, the grafting-to NPs had slightly higher Ms than the grafting-from counterparts. In addition, the Ms of both kinds of the Fe3O4-PGMA NPs with higher Fe3O4 content (> 87%) were also higher than that of the fluidMAG-Amine, the commercially available amine-modified MNPs. Besides, both kinds of Fe3O4-PGMA NPs also had much higher Fe3O4 contents and Ms values than most of the reported PGMA-modified MNPs. The magnetic epoxy nanocomposites (MENCs) were prepared by blending the modified Fe3O4 NPs into bisphenol A diglycidyl ether (BADGE)-based epoxy system and the distributions of both kinds of the PGMA-modified NPs were much better than that of the oleic acid-modified Fe3O4 NPs. Similar to the NPs, the MENCs also exhibited superparamagnetism. By cross-section TEM observation, the grafting-to Fe3O4-PGMA NPs formed more homogeneous distributions with smaller cluster size than the grafting-from counterparts and gave higher Ms of the MENCs. Nondestructive flaw detection of surface and sub-surface defects could be successfully achieved by brightness contrast of images given through eddy current testing (ET) method, which is firstly reported. The mechanical properties of the materials were influenced very slightly when 2.5% or lower Fe3O4-gt-PGMA NPs were present while the presence of the Fe3O4-gf-PGMA NPs (1 – 2.5 %) gave mild improvement of the storage modulus and increase of the glass-rubber transition temperature(Tg) of the MENCs. Furthermore, the Fe3O4-PGMA NPs could be evenly coated onto the functionalized ultra-high molecular weight poly(ethylene) (UHMWPE) textiles. The Fe3O4-gt-PGMA NPs were coated on the textile in order to prepare NP-coated textile-reinforced composite. Preliminary result of ET measurement showed that the Fe3O4-gt-PGMA NPs coated on the textiles could visualize the structure of the textile hidden inside and their relative depth. Accordingly, the incorporation of MNPs to polymers opens a new pathway of damage-free structural health monitoring of polymeric materials.

Here, we report on a new temperature responsive polymer brush system with a terminal “click” functionality. Bifunctionalized poly(N-isopropylacrylamide) (PNiPAAm) with distinct functional end groups was synthesized by atom transfer radical polymerization (ATRP) and grafted to a modified silicon substrate. The presence of the active terminal alkyne functionality is validated using an azide-modified rhodamine B (N3-RhB) via copper(I) catalyzed alkyne–azide cycloaddition (CuAAC). The optical properties and swelling dynamics of an N3-RhB modified PNiPAAm brush are analyzed in dry state and in situ by VIS-spectroscopic ellipsometry (SE). The best-fit results are obtained using a Gaussian oscillator model and are confirmed by UV/VIS-spectroscopy. We observed evidence of interactions between the aromatic residues of the dye and the PNiPAAm amide groups, which significantly affect the swelling behavior of the modified polymer brush. / Dieser Beitrag ist mit Zustimmung des Rechteinhabers aufgrund einer (DFG-geförderten) Allianz- bzw. Nationallizenz frei zugänglich.

The poly(glycidyl methacrylate)-modified magnetite nanoparticles, Fe3O4-PGMA NPs, were investigated and applied in nondestructive flaw detection of polymeric materials in this research. The Fe3O4 endowed magnetic property to the materials for flaw detection while the PGMA promoted colloidal stability and prevented particle aggregation. The magnetite nanoparticles (Fe3O4 NPs) were successfully synthesized by coprecipitation and then surface-modified with PGMA to form PGMA-modified Fe3O4 NPs by both grafting-from and grafting-to approaches. For the grafting-from approach, the Fe3O4 NPs were surface-functionalized with α-bromo isobutyryl bromide (BIBB) to form BIB-modified Fe3O4 NPs (Fe3O4-BIB NPs) with covalent linkage. The resultant Fe3O4-BIB NPs were used as surface-initiators to grow PGMA by surface-initiated atom transfer radical polymerization (SI-ATRP). For the grafting-to approach, the Fe3O4 NP were surface-functionalized with (3-mercaptopropyl)triethoxysilane (MCTES) to form MCTES-modified Fe3O4 NPs (Fe3O4-MCTES NPs). The PGMA with Br-end group was pre-synthesized by ATRP and then was grafted to the surface of the Fe3O4-MCTES NPs by coupling reaction. Both bare and modified Fe3O4 NPs exhibited superparamagnetism and the existence of iron oxide in the form of Fe3O4 was confirmed. The particle size of individual Fe3O4 NPs was about 8 – 24 nm but they aggregated to form clusters. The PGMA-modified NPs formed stable dispersion in chloroform and had larger cluster sizes than the unmodified ones because of the PGMA polymer layer. However, the uniformity of the NP clusters could be improved with PGMA surface grafting. The PGMA surface layer of the grafting-from (Fe3O4-gf-PGMA) NPs was thin and dense while that of the grafting-to (Fe3O4-gt-PGMA) NPs was thick and loose. The hydrodynamic diameters (Zave) of Fe3O4-gf-PGMA NP clusters could be controlled between 176 to 643 nm, dependent on the PGMA contents and reaction conditions. During SI-ATRP, side reactions happened and caused NP aggregation as well as increase of size of NP clusters. However, the aggregation has been minimized through optimization of reaction conditions. Oppositely, Zave values of Fe3O4-gt-PGMA NPs had little variation of about 120 – 190 nm. And the PGMA content of the Fe3O4-gt-PGMA NPs was limited to 12.5% because of the spatial hindrance during grafting process. The saturation magnetization (Ms) of the unmodified Fe3O4 NPs was about 77 emu/g, while those of the grafting-from and grafting-to Fe3O4-PGMA NPs were 50 – 66 emu/g and 63 – 70 emu/g, respectively. For Fe3O4-PGMA NPs with similar Fe3O4 contents, the grafting-to NPs had slightly higher Ms than the grafting-from counterparts. In addition, the Ms of both kinds of the Fe3O4-PGMA NPs with higher Fe3O4 content (> 87%) were also higher than that of the fluidMAG-Amine, the commercially available amine-modified MNPs. Besides, both kinds of Fe3O4-PGMA NPs also had much higher Fe3O4 contents and Ms values than most of the reported PGMA-modified MNPs. The magnetic epoxy nanocomposites (MENCs) were prepared by blending the modified Fe3O4 NPs into bisphenol A diglycidyl ether (BADGE)-based epoxy system and the distributions of both kinds of the PGMA-modified NPs were much better than that of the oleic acid-modified Fe3O4 NPs. Similar to the NPs, the MENCs also exhibited superparamagnetism. By cross-section TEM observation, the grafting-to Fe3O4-PGMA NPs formed more homogeneous distributions with smaller cluster size than the grafting-from counterparts and gave higher Ms of the MENCs. Nondestructive flaw detection of surface and sub-surface defects could be successfully achieved by brightness contrast of images given through eddy current testing (ET) method, which is firstly reported. The mechanical properties of the materials were influenced very slightly when 2.5% or lower Fe3O4-gt-PGMA NPs were present while the presence of the Fe3O4-gf-PGMA NPs (1 – 2.5 %) gave mild improvement of the storage modulus and increase of the glass-rubber transition temperature(Tg) of the MENCs. Furthermore, the Fe3O4-PGMA NPs could be evenly coated onto the functionalized ultra-high molecular weight poly(ethylene) (UHMWPE) textiles. The Fe3O4-gt-PGMA NPs were coated on the textile in order to prepare NP-coated textile-reinforced composite. Preliminary result of ET measurement showed that the Fe3O4-gt-PGMA NPs coated on the textiles could visualize the structure of the textile hidden inside and their relative depth. Accordingly, the incorporation of MNPs to polymers opens a new pathway of damage-free structural health monitoring of polymeric materials.:1. Introduction 2. Theoretical section 2.1. Magnetite Nanoparticles (MNPs) 2.2. Applications of MNPs 2.3. Atom transfer radical polymerization (ATRP) 2.4. Magnetic nanocomposites (MNCs) 2.5. Damage-free structural health monitoring (SHM) using MNPs 3. Objective of the work 4. Materials, methods and characterization 4.1. Materials 4.2. Methods 4.3. Formation of polymeric magnetic nanocomposites 4.4. Characterization 5. Results and discussions 5.1. Unmodified magnetite nanoparticles (Fe3O4 NPs) 5.2. Oleic acid-modified (Fe3O4–OA) NPs 5.3. PGMA-modified NPs by grafting-from approach (Fe3O4-gf-PGMA NPs) 5.4. PGMA-modified NP by grafting-to approach (Fe3O4-gt-PGMA NPs) 5.5. Comparison between grafting-from and grafting-to Fe3O4-PGMA NPs 5.6. Magnetic epoxy nanocomposites (MENCs) 5.7. Fiber-reinforced epoxy nanocomposites 6. Conclusions and outlook 7. Appendix 8. List of figures, schemes and tables 9. References Versicherung Erklaerung List of publications