No description available.

ITC/USA 2011 Conference Proceedings / The Forty-Seventh Annual International Telemetering Conference and Technical Exhibition / October 24-27, 2011 / Bally's Las Vegas, Las Vegas, Nevada / This paper concentrates on aircraft specific issues and impacts of utilizing a "C" band telemetry system on a new or existing instrumentation system.

This thesis describes the use of a multi-amplitude minimum shift keying (MAMSK) signal in various types of wireless communication system. A MAMSK signal is a bandwidth efficient modulation scheme obtained by superimposing ℳ minimum shift keying (MSK) signals with unequal amplitudes. The overall phase of a MAMSK signal is controlled by the phase of the largest component MSK signal which allows the use of a low-complexity differential detector. A closed form expression for the average bit error rate (BER) for coherent detection of an MAMSK in AWGN is derived and is shown to achieve the same BER as that of square constellation quadrature amplitude modulation (QAM) with the same average transmit power. We describe the design and implementation of a STBC-based MIMO radio system in conjunction with MAMSK modulation. The proposed system provides high capacity data transmission by carrying information not only in the phases but also in the amplitude. Despite using a simple MAMSK differential receiver the system achieves performance within 1 dB of coherent detection. The existing MSK modems in conjunction with STBC could easily be modified to construct the proposed system. The MAMSK modulation scheme is extended to a multiuser relaying network where two nodes cooperate in a half-duplex environment to achieve diversity gain. The cooperative scheme is based on superposition modulation using a decode-and-forward (DF) strategy. In the proposed scheme, each node simultaneously transmits its own and the relayed signals by superimposing one on the other. A MAMSK signal is an excellent choice for this type of cooperative communication due its being obtained by a superposition technique. The proposed system exploits the overall phase of a MAMSK signal which allows differential detection and as a result it provides the lowest decoding complexity and memory requirements among the existing superposition based cooperation schemes. The performance of the system is evaluated by simulation, where it is shown that the MAMSK cooperative system outperforms a conventional DF scheme in terms of both power and bandwidth efficiency.

Ultra wide band (UWB) is an extremely promising wireless technology for researchers and industrials. One of the most interesting is its high data rate and fading robustness due to selective frequency fading. However, beside such advantages, UWB system performance is highly affected by existing narrowband interference (NBI), undesired UWB signals and tone/multi-tone noises. For this reason, research about NBI cancellation is still a challenge to improve the system performance vs. receiver complexity, power consumption, linearity, etc. In this work, the two major receiver sections, i.e., analog (radiofrequency or RF) and digital (digital signal processing or DSP), were considered and new techniques proposed to reduce circuit complexity and power consumption, while improving signal parameters. In the RF section, different multiband UWB low-noise amplifier key design parameters were investigated like circuit configuration, input matching and desired/undesired frequency band filtering, highlighting the most suitable filtering package for efficient UWB NBI cancellation. In the DSP section, due to pulse transmitter signals, different issues like modulation type and level, pulse variety, shape and color noise/tone noise assumptions, were addressed for efficient NBI cancelation. A comparison was performed in terms of bit-error rate, signal-to-interference ratio, signal-to-noise ratio, and channel capacity to highlight the most suitable parameters for efficient DSP design. The optimum number of filters that allows the filter bandwidth to be reduced by following the required low sampling rate and thus improving the system bit error rate was also investigated.

In the first part of the thesis, protein-ligand interactions were investigated using the chaperone LcrH, from Yersinia as target protein. The structure of a peptide encompassing the amphipathic domain (residue 278-300) of the protein YopD from Yersinia was determined by NMR in 40% TFE. The structure of YopD278-300 is a well defined α-helix with a β-turn at the C-terminus of the helix capping the structure. This turn is crucial for the structure as peptides lacking the residues involved in the turn are unstructured. NMR relaxation indicates that the peptide is not monomeric. This is supported by intermolecular NOEs found from residue Phe280 to Ile288 and Val292 indicative of a multimeric structure with the helical structures oriented in an antiparallel manner with hydrophobic residues forming the oligomer. The interaction with the chaperone LcrH was confirmed by 1H relaxation experiments and induced chemical shift changes in the peptide Protein-ligand interactions were investigated further in the second paper using a different approach. A wide range of substances were used in screening for affinity against the chaperones PapD and FimC from uropathogenic Escherichia coli using 1H relaxation NMR experiments, surface plasmon resonance and 19F NMR. Fluorine NMR proved to be advantageous as compared to proton NMR as it is straight forward to identify binding ligands due to the well resolved 19F NMR spectra. Several compounds were found to interact with PapD and FimC through induced line-broadening and chemical shift changes for the ligands. Data corroborate well with surface plasmon resonance and proton NMR experiments. However, our results indicate the substances used in this study to have poor specificity for PapD and FimC as the induced chemical shift is minor and hardly no competitive binding is observed. Paper III and IV is an investigation of the structural features of the allergenic 2S albumin Ber e 1 from Brazil nut. Ber e 1 is a 2S albumin previously identified as the major allergen of Brazil nut. Recent studies have demonstrated that endogenous Brazil nut lipids are required for an immune response to occur in vivo. The structure was obtained from 3D heteronuclear NMR experiments followed by simulated annealing using the software ARIA. Interestingly, the common fold of the 2S albumin family, described as a right-handed super helix with the core composed of a helix bundle, is not found in Ber e 1. Instead the C-terminal region is participating in the formation of the core between helix 3, 4 and 5. The dynamic properties of Ber e 1 were investigated using 15N relaxation experiments and data was analyzed using the model-free approach. The analysis showed that a few residues in the loop between helix 2 and 3 experience decreased mobility, compared to the rest of the loop. This is consistent with NOE data as long range NOEs were found from the loop to the core region of the protein. The anchoring of this loop is a unique feature of Ber e 1, as it is not found in any other structures of 2S albumins. Chemical shift mapping of Ber e 1 upon the addition of lipid extract from Brazil nut identified 4 regions in the protein where chemical shift perturbations were detected. Interestingly, all four structural clusters align along a cleft in the structure formed by helix 1-3 on one side and helix 4-5 on the other. This cleft is big enough to encompass a lipid molecule. It is therefore tempting to speculate whether this cleft is the lipid binding epitope in Ber e 1.

Ultra wide band (UWB) is an extremely promising wireless technology for researchers and industrials. One of the most interesting is its high data rate and fading robustness due to selective frequency fading. However, beside such advantages, UWB system performance is highly affected by existing narrowband interference (NBI), undesired UWB signals and tone/multi-tone noises. For this reason, research about NBI cancellation is still a challenge to improve the system performance vs. receiver complexity, power consumption, linearity, etc. In this work, the two major receiver sections, i.e., analog (radiofrequency or RF) and digital (digital signal processing or DSP), were considered and new techniques proposed to reduce circuit complexity and power consumption, while improving signal parameters. In the RF section, different multiband UWB low-noise amplifier key design parameters were investigated like circuit configuration, input matching and desired/undesired frequency band filtering, highlighting the most suitable filtering package for efficient UWB NBI cancellation. In the DSP section, due to pulse transmitter signals, different issues like modulation type and level, pulse variety, shape and color noise/tone noise assumptions, were addressed for efficient NBI cancelation. A comparison was performed in terms of bit-error rate, signal-to-interference ratio, signal-to-noise ratio, and channel capacity to highlight the most suitable parameters for efficient DSP design. The optimum number of filters that allows the filter bandwidth to be reduced by following the required low sampling rate and thus improving the system bit error rate was also investigated.

There is a growing demand for the high quality TV programs such as High Definition TV (HDTV). The CATV network is often a suitable solution to address this demand using a CATV modem delivering high data rate digital signals in a cost effective manner, thereby, utilizing a complex digital modulation scheme is inevitable. Exploiting complex modulation schemes, entails a more sophisticated modulator and distribution system with much tighter tolerances. However, there are always distortions introduced to the modulated signal in the modulator degrading signal quality.<p> In this research, the effect of distortions introduced by the RF band pass filter in the modulator will be considered which cause degradations on the quality of the output Quadrature Amplitude Modulated (QAM) signal. Since the RF filter's amplitude/group delay distortions are not symmetrical in the frequency domain, once translated into the base band they have a complex effect on the QAM signal. Using Matlab, the degradation effects of these distortions on the QAM signal such as Bit Error Rate (BER) is investigated.<p> In order to compensate for the effects of the RF filter distortions, two different methods are proposed. In the first method, a complex base band compensation filter is placed after the pulse shaping filter (SRRC). The coefficients of this complex filter are determined using an optimization algorithm developed during this research. The second approach, uses a pre-equalizer in the form of a Feed Forward FIR structure placed before the pulse shaping filter (SRRC). The coefficients of this pre-equalizer are determined using the equalization algorithm employed in a test receiver, with its tap weights generating the inverse response of the RF filter. The compensation of RF filter distortions in base band, in turn, improves the QAM signal parameters such as Modulation Error Ratio (MER). Finally, the MER of the modulated QAM signal before and after the base band compensation is compared between the two methods, showing a significant enhancement in the RF modulator performance.

Channel coding has been largely used for the purpose of improving error performance on a communications system. Typical methods based on added redundancy allow for error detection and correction, this improvement however comes at a cost of bandwidth. This thesis focuses on channel coding for the bandwidth-limited channel where no bandwidth expansion is allowed. We first discuss the idea of coding for the bandwidth-limited channel as seen from the signal space point of view where the purpose of coding is to maximize the Euclidian distance between constellation points without increasing the total signal power and under the condition that no extra bits can be added. We then see the problem from another angle and identify the tradeoffs related to bandwidth and error performance. This thesis intends to find a simple way of achieving an improvement in error performance for the bandwidth-limited channel without the use of lattice codes or trellis-coded modulation. The proposed system is based on convolutional coding followed by multilevel transmission. It achieved a coding gain of 2 dB on Eb/No or equivalently, a coding gain of approximately 2.7 dB on SNRnorm without increase in bandwidth. This coding gain is better than that obtained by a more sophisticated lattice code Gosset E8 at the same error rate.

There is a growing demand for the high quality TV programs such as High Definition TV (HDTV). The CATV network is often a suitable solution to address this demand using a CATV modem delivering high data rate digital signals in a cost effective manner, thereby, utilizing a complex digital modulation scheme is inevitable. Exploiting complex modulation schemes, entails a more sophisticated modulator and distribution system with much tighter tolerances. However, there are always distortions introduced to the modulated signal in the modulator degrading signal quality.<p> In this research, the effect of distortions introduced by the RF band pass filter in the modulator will be considered which cause degradations on the quality of the output Quadrature Amplitude Modulated (QAM) signal. Since the RF filter's amplitude/group delay distortions are not symmetrical in the frequency domain, once translated into the base band they have a complex effect on the QAM signal. Using Matlab, the degradation effects of these distortions on the QAM signal such as Bit Error Rate (BER) is investigated.<p> In order to compensate for the effects of the RF filter distortions, two different methods are proposed. In the first method, a complex base band compensation filter is placed after the pulse shaping filter (SRRC). The coefficients of this complex filter are determined using an optimization algorithm developed during this research. The second approach, uses a pre-equalizer in the form of a Feed Forward FIR structure placed before the pulse shaping filter (SRRC). The coefficients of this pre-equalizer are determined using the equalization algorithm employed in a test receiver, with its tap weights generating the inverse response of the RF filter. The compensation of RF filter distortions in base band, in turn, improves the QAM signal parameters such as Modulation Error Ratio (MER). Finally, the MER of the modulated QAM signal before and after the base band compensation is compared between the two methods, showing a significant enhancement in the RF modulator performance.

Carl Philipp Emanuel Bach (1714-1788) published his Versuch &#x00FC;ber die wahre Art das Clavier zu spielen in 1753 and 1762. It was the most important essay on keyboard performance practice of the mid-eighteenth century. The publication of this book also made C. P. E. Bach the most influential keyboard pedagogue of the eighteenth century. The last chapter of the Vers&#x00FC;ch, titled ¡§Improvisation¡¨, explains his concepts of ¡§Freie Fantasia¡¨ and provides suggestions for performing the fantasia. C. P. E. Bach points out that Freie Fantasia is a kind of composition in which the performer has much freedom for improvising and for expressing his emotion. This thesis is divided into three sections, excluding the introduction and the conclusion. The first section discusses the development of the fantasia before the eighteenth century. It explores the change of styles and compositional technique of the fantasia from the sixteenth to the eighteenth century. The second part includes an introduction of the life of C. P. E. Bach, his style of composition, technique of improvisation and how he applies his improvisational techniques in his fantasia. The third part provides the definition of ¡§Freie Fantasia¡¨, discusses the influences of J. S. Bach¡¦s Chromatic Fantasia and Fugue in D Minor on him, and elaborates on the characteristics of the Freie Fantasia, including the recitative style, meter-free and formal structure, virtuosic passages, bold modulations, and the use of contrasting materials. Examples are also provided in this part.