<p> </p><p>The aim of this Master Thesis is to assess the load carrying capacity of the Glomman Bridge outside of the Swedish city Örebro. The Glomman Bridge is an unreinforced concrete single span arch bridge with backfill. The bridge was constructed in 1923 on assignment from the Swedish National Railways (SJ).</p><p>The failure criteria used in this thesis is that the bridge collapses when any cross section in the concrete arch reaches its ultimate capacity. In reality, the bridge may manage heavier loads than this. When the capacity is reached in a cross section, a hinge is formed and the arch relocates the forces to other parts of the arch that can carry higher stresses. The real bridge will not collapse until a fourth hinge is formed, and by that a mechanism. To be able to calculate the cross section forces in the arch, it was necessary to know the influences of the loads on the arch when they were run along the bridge. For this purpose, influence lines were obtained from a 2D finite element model created in ABAQUS, a general FE-analyses software. A calculation routine to find the least favourable load combination was then created in Matlab, a numerical calculation software. The routine was made to find the worst case among different load cases and to combine the standardized axle pressures with the present number of axles.</p><p>A parametric survey was also performed because the material properties for the different parts of the bridge are very uncertain. In the survey, the initial values were changed one at a time to study the outcome on the load factor. The load factor is the ratio between the ultimate limit load and the actual load. The studied parameters are the compressive strength, the Young's modulus, the density and the Poisson's ratio of the different parts of the bridge. The parameters are studied individually irrespective of possible correlation. The studied parts of the bridge are the backfill, the arch, the abutments and the asphalt. The clearly most important component is found to be the backfill. With increased stiffness or increased Poisson's ratio in the backfill follows increased load factor.</p><p>The equations behind the failure envelope can be derived from equilibrium equations for the unreinforced cross section. The influence lines are normalised with respect to the capacity of the cross section to get the degree of efficiency along the whole length of the arch, instead of the common influence lines that give the cross section forces. This is done because the failure is not caused by large cross section forces but by an exceeded ultimate stress. As the different loads are run along the bridge, the largest positive and negative efficiency for bending moment and normal force are localised. The normalised cross section forces are plotted together with the failure envelope and the load factor is then calculated.</p><p>Several masonry arch bridges were loaded until collapse in a study performed by the British Transport and Road Research Laboratory. One of the bridges in the study, the Prestwood Bridge, has been used in this thesis as a comparison to the Glomman Bridge. The load carrying capacity of the Prestwood Bridge is known, and is used to verify that the method using the failure envelope is applicable.</p><p>To compare the results from the cross section analysis from the failure envelope model to another method, the Glomman Bridge and the Prestwood Bridge were also tested in the commercial software RING 2.0. The method used in RING 2.0 differs from the failure mode in this thesis by calculating the load factor when four different cross sections reach their capacity and the bridge collapses.</p><p>The failure envelope method allows an A/B-value (Axle- and Bogie load) of 102 kN/147 kN when using very poor values of the parameters and 181 kN/226 kN when using a reference case with normal parameters.</p><p>Although the load capacity is found to be acceptable, the uncertainties are still large. To get a more accurate apprehension of the condition of the actual bridge, further research should be carried out, such as e.g. a non-linear model.</p> / <p>Syftet med föreliggande examensarbete är att uppskatta bärförmågan hos bron Glomman utanför Örebro. Glomman är en oarmerad betongvalvbro i ett spann med ovanliggande jordfyllning. Bron byggdes 1926 på uppdrag av Statens Järnvägar (SJ).</p><p>Brottkriteriet i detta examensarbete är att bron går till brott när något tvärsnitt i betongbågen uppnår sin kapacitet. I själva verket är det möjligt att bron kan klara tyngre last än detta. När kapaciteten nås i ett tvärsnitt uppstår en led och bågen omlagrar krafterna till andra bågdelar som klarar större spänningar. Den verkliga bron rasar inte förrän en fjärde led har utvecklats, och därmed en mekanism. För att kunna beräkna tvärsnittskrafterna i bågen, var det nödvändigt att känna till trafiklasternas påverkan på bågen när de kördes över bron. För detta ändamål erhölls influenslinjer från en tvådimensionell finita elementmodell skapad i ABAQUS, ett generellt FE-program. En beräkningsrutin för att finna värsta tänkbara lastkombinering skapades i Matlab, ett numeriskt beräkningsprogram. Rutinen utformades för att hitta värsta fallet bland olika lastfall samt för att kombinera standardiserade axeltryck med det aktuella antalet axlar.</p><p>En parameterstudie utfördes också då materialegenskaperna för de olika delarna i bron är mycket osäkra. I parameterstudien ändrades ingångsvärdena ett åt gången för att studera utslaget på lastfaktorn. Lastfaktorn är förhållandet mellan brottgränslasten och den verkliga lasten. De parametrar som studeras är tryckhållfastheten, <em>E</em>-modulen, densiteten och tvärkontraktionen för de olika brodelarna. Parametrarna studeras enskilt utan hänsyn till eventuell korrelation. De brodelar som studeras är fyllningen, bågen, fundamenten och asfalten. Den klart viktigaste komponenten visar sig vara fyllningen. Med ökad styvhet eller ökad tvärkontraktion i fyllningen följer ökad last­faktor.</p><p>Ekvationerna bakom brottenveloppet kan härledas ur jämviktsekvationer för det oarmerade tvärsnittet. Influenslinjerna normeras med avseende på tvärsnittets kapa­citet för att få ut utnyttjandegraden längs hela bågen. Detta görs då det egentligen inte är för stor tvärsnittskraft som orsakar brott utan för stor spänning. Högsta och lägsta utnyttjandegrad för böjande moment och normalkraft lokaliseras när de olika typlasterna körs över bron. Utnyttjandegraderna placeras i brottenveloppet för att sedan räkna fram en lastfaktor.</p><p>Ett flertal liknande broar har lastats till brott i en studie genomförd av British Transport and Road Research Laboratory. En av broarna i studien, Prestwood Bridge, har använts i denna rapport som jämförelse med Glomman. Då bärförmågan hos Prestwood Bridge är känd används den till att bekräfta att metoden med brott­enveloppet är tillämpbar.</p><p>För att jämföra resultaten från tvärsnittsanalysen i brottenveloppmetoden med en annan metod, testades även Glomman och Prestwood Bridge i det kommersiella programmet RING 2.0. Metoden som används i RING 2.0 skiljer sig från brottmoden i denna rapport genom att istället beräkna lastfaktorn när fyra olika tvärsnitt har uppnått sina kapaciteter och bron kollapsar.</p><p>Metoden med brottenvelopp tillåter ett A/B-värde (Axel- och Boggitryck) på 102 kN/147 kN när mycket dåliga parametervärden används och 181 kN/226 kN när referensfallet med normala parametervärden används.</p><p>Även om bärförmågan kan anses vara acceptabel är osäkerheterna stora. För att få en nogrannare uppfattning om brons faktiska tillstånd bör fortsatta studier utföras, som t.ex. en icke-linjär modell.</p>

Am Übergang von Brückenbauwerken zu den angrenzenden Hinterfüllungen treten teilweise größere Unebenheiten der Fahrbahnoberfläche im Längsprofil auf. Eine Ursache dafür können Setzungen innerhalb der Hinterfüllung sein. Um diesen Anteil unter realen Bedingungen zu untersuchen, wurden an zwei Autobahnbrücken acht unterschiedlichen Hinterfüllungen ausgeführt und die Verformungen unter Verkehrsbelastung mit einem aufwändigen Messprogramm über einen Beobachtungszeitraum von bis zu vier Jahren erfasst. Im Ergebnis konnte für diese beiden Brücken gezeigt werden, dass die Setzungen unter Verkehrsbelastung nur wenige Millimeter betrugen und deutlich kleiner waren als die Höhenungenauigkeiten beim Einbau der Asphaltdeckschicht. Die Fahrbahnebenheit im Längsprofil wurde allein durch den Zustand vor Verkehrsfreigabe geprägt. Einfache Sofortmaßnahmen zur Erhöhung der Einbaugenauigkeit werden in der Arbeit vorgeschlagen. In einem weiteren Teil werden Erddruck- und Verformungsmessungen an zwei Hinterfüllungen einer integralen Rahmenbrücke vorgestellt.

The use of backfill in underground mining is increasing due to need for systematic backfilling of mine openings and workings to avoid surface damage, increase safety and contribution to sustainable mining. This study is to investigate backfill materials and new methods suited for systematic selection and application of backfill in underground mines. Laboratory tests were carried out on physical, chemical and mechanical properties of different backfill materials and mixtures thereof. Special attention was paid to materials generated as by-products and other cheaply available materials e.g. fly ash and FGD-gypsum from power plants, natural and synthetic anhydrite. The different material mixtures investigated can be used as a technically and economically viable backfill for underground mines. In summary, the systematic selection of backfill materials from by-products, mine waste and tailings from the mineral processing of mining industry and other industries were suited as a backfill material for test field in China coal fires and recommended for underground potash mines in Thailand.

Master of Science / Department of Civil Engineering / Stacey Kulesza / In Kansas, mechanically stabilized earth (MSE) retaining walls are typically backfilled with coarse aggregate. Current backfill material testing procedures used by the Kansas Department of Transportation (KDOT) utilize on-site observations for construction quality assurance and the American Association of State Highway and Transportation Officials standard T 288-12 (“Standard Method of Test for Determining Minimum Laboratory Soil Resistivity”). AASHTO T 288-12 is designed to test a soil sample’s electrical resistivity (ER) that correlates to its corrosion potential. However, the test, based on material passing through a No. 10 sieve, is inappropriate for coarse aggregate typically used by KDOT as the aggregate will be retained on a No. 10 sieve and potentially leads to over-conservative designs. However, ER imaging provides a two-dimensional (2D) profile of bulk ER of backfill material, thereby yielding more information regarding backfill uniformity compared to traditional sampling. The objective of this study was to characterize bulk ER of in-place MSE wall backfill aggregate. In this study, MSE walls selected by KDOT were tested using ER imaging during construction to determine bulk ER of the backfill. Variations within backfill ER may be a result of varying aggregate material, inclusions of fines, thoroughness of compaction, and the presence of water. ER imaging was used on five walls: four MSE walls and one gravity retaining wall that contained no reinforcement. One MSE wall contained metal reinforcement, while the other four walls contained geosynthetic. The ER imaging field method produced a 2D profile that depicted ER uniformity for bulk analysis. A post processing algorithm was generated to remove the subjective nature of the ER imaging results. The program determines the bulk ER based upon the ER imaging results. These results indicate that the laboratory analysis of AASHTO T 288-12 under-estimates the bulk ER of in-situ backfill material. Identification of a material’s bulk ER will help characterize the ER of aggregates in a complementary KDOT project. Results of this study will be used to recommend an in-situ test method for aggregate used by KDOT.

Made available in DSpace on 2014-10-09T12:36:01Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:59:48Z (GMT). No. of bitstreams: 0 / Dissertação (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

Made available in DSpace on 2014-10-09T12:36:01Z (GMT). No. of bitstreams: 0 / Made available in DSpace on 2014-10-09T13:59:48Z (GMT). No. of bitstreams: 0 / Pasta de cimento é um material comum em repositórios para rejeitos radioativos, atuando como material estrutural e de imobilização. Sua utilização como material de preenchimento em um repositório tipo poço tubular profundo para fontes seladas, no entanto, requer um maior tempo de vida útil do material. O conhecimento de seu comportamento em longo prazo é necessário para garantir a segurança da instalação em milhares de anos. O presente trabalho avaliou as alterações na pasta de cimento induzidas por fatores de degradação, como ataque de agentes agressivos, alta temperatura e presença de campo de radiação. Corpos de prova (cps) de pasta de cimento foram submetidos a ensaios acelerados de degradação e os efeitos deletérios foram avaliados por meio de ensaios de resistência mecânica, variação dimensional, lixiviação/penetração de íons, DRX, TGA e MEV. Observou-se que a hidratação dos cps foi beneficiada pela imersão (em água destilada ou em solução salina) e alta temperatura, resultando em uma resistência maior. O armazenamento à seco prejudicou a hidratação, mantendo a resistência mais baixa. O tempo de imersão e a irradiação não foram capazes de alterar a mineralogia e a resistência da pasta de cimento. / Dissertação (Mestrado) / IPEN/D / Instituto de Pesquisas Energeticas e Nucleares - IPEN-CNEN/SP

The use of backfill in underground mining is increasing due to need for systematic backfilling of mine openings and workings to avoid surface damage, increase safety and contribution to sustainable mining. This study is to investigate backfill materials and new methods suited for systematic selection and application of backfill in underground mines. Laboratory tests were carried out on physical, chemical and mechanical properties of different backfill materials and mixtures thereof. Special attention was paid to materials generated as by-products and other cheaply available materials e.g. fly ash and FGD-gypsum from power plants, natural and synthetic anhydrite. The different material mixtures investigated can be used as a technically and economically viable backfill for underground mines. In summary, the systematic selection of backfill materials from by-products, mine waste and tailings from the mineral processing of mining industry and other industries were suited as a backfill material for test field in China coal fires and recommended for underground potash mines in Thailand.

Skewed bridges have exhibited poorer performance during lateral earthquake loading when compared to non-skewed bridges (Apirakvorapinit et al. 2012; Elnashai et al. 2010). Results from small-scale laboratory tests by Rollins and Jessee (2012) and numerical modeling by Shamsabadi et al. (2006) suggest that skewed bridge abutments may provide only 35% of the non-skewed peak passive resistance when a bridge is skewed 45°. This reduction in peak passive force is of particular importance as 40% of the 600,000 bridges in the United States are skewed (Nichols 2012). Passive force-deflection results based on large-scale testing for this study largely confirm the significant reduction in peak passive resistance for abutments with longitudinal reinforced concrete wingwalls. Large-scale lateral load tests were performed on a non-skewed and 45° skewed abutment with densely compacted sand backfill. The 45° skewed abutment experienced a 54% reduction in peak passive resistance compared to the non-skewed abutment. The peak passive force for the 45° skewed abutment was estimated to occur at 5.0% of the backwall height compared to 2.2% of the backwall height for the non-skewed abutment. The 45° skewed abutment displayed evidence of rotation, primarily pushing the obtuse side of the abutment into the backfill, significantly more than the non-skewed abutment as it was loaded into the backfill. The structural and geotechnical response of the wingwalls was also monitored during large-scale testing. The wingwall on the obtuse side of the 45° skewed abutment experienced nearly 6 times the amount of horizontal soil pressure and 7 times the amount of bending moment compared to the non-skewed abutment. Pressure and bending moment distributions are provided along the height of the wingwall and indicate that the maximum moment occurs approximately 20 in (50.8 cm) below the top of the wingwall. A comparison of passive force per unit width suggests that MSE wall abutments provide 60% more passive resistance per unit width compared to reinforced concrete wingwall and unconfined abutment geometries at zero skew. These findings suggest that changes should be made to current codes and practices to properly account for skew angle in bridge design.

One hundred billion tons of mine solid waste are estimated to be produced worldwide each year. In Canada, the mining and oil industries produce the most solid and semi-solid waste in the country, with more than a billion tons each year. In the earlier days of mining, the initial practices that were used to contain these waste materials consisted of surface storage, river dumping or just simple abandonment, while the more recent practices include dam impoundment and underground waste fill. These methods however can potentially cause environmental hazards and geotechnical problems. Against this context and as a result of stricter environmental regulations, cemented paste backfilling has been developed as a solution. This relatively new technology uses the produced waste tailings to backfill the mine stopes, greatly reducing their environmental impact while offering proper structural support in an efficient manner. However, the cost of cemented paste backfill (CPB) is greatly impacted by the binder content which can constitute up to 75% of its total cost. Additionally, the binder is usually mostly composed of ordinary Portland cement, and its production is highly energy-intensive and generates a large volume of carbon dioxide (CO₂). Indeed, it is estimated that the cement industry accounts for approximately 7% of the global anthropogenic CO₂ emissions, which is expected to increase on an annual basis. All of these factors have compelled the mining industry to seek alternatives for cement to enhance CPB strength, in hopes of reducing its carbon footprint. Against this context, this study investigates the effect of the addition of nanoparticles, namely nano silica (SiO₂) and nano-calcium carbonate (CaCO₃), on the strength development of CPB cured at a constant room temperature and in non-isothermal conditions. Nanoparticles have been studied and used as chemical admixtures in different cementitious materials with promising results; non-isothermal curing conditions better reflect the in-situ thermal curing conditions of CPB. Thus, numerous different laboratory tests and analyses, including uniaxial compressive strength (UCS), scanning electron microscopy (SEM) and mercury intrusion porosimetry (MIP) tests, thermogravimetric/derivative thermogravimetric (TG/DTG) analyses and electrical conductivity monitoring, have been conducted on CPB samples with or without nanoparticles, and cured at room temperatures or under non-isothermal conditions. The non-isothermal conditions replicate the development of temperature in two different sizes of CPB structures in the field. The results show that CPB that contains nanoparticles show a higher UCS over the entire period of curing in all of the tested conditions. The mechanical performance is further enhanced when tested under higher temperatures in non-isothermal temperature profiles. Most of the strength increase takes place at the early ages (3 days) of the testing. The reason for the improvement in the mechanical strength is linked to accelerated binder hydration and the nucleating and filler effects of the nano-material, which is corroborated by results obtained through microstructural analyses and EC monitoring. The use of natural gold tailings affects the mechanical performance of CPB and the accelerating effect of the nanoparticles due to sulphate attacks. Overall, these promising findings can help to contribute to reducing the carbon footprint of mining activities, and improve the efficiency and cost-effectiveness of mine backfilling processes.

Low-strength cellular concrete consists of a cement slurry that is aerated prior to placement. It remains a largely untested material with properties somewhere between those of soil, geofoam, and typical controlled low-strength material (CLSM). The benefits of using this material include its low density, ease of placement, and ability to self-compact. Although the basic laboratory properties of this material have been investigated, little information exists about the performance of this material in the field, much less the passive resistance behavior of this material in the field.In order to evaluate the use of cellular concrete as a backfill material behind bridge abutments, two large-scale tests were conducted. These tests sought to better understand the passive resistance, the movement required to reach this resistance, the failure mechanism, and skew effects for a cellular concrete backfill. The tests used a pile cap with a backwall face 5.5 ft (1.68 m) tall and 11 ft (3.35 m) wide. The backfill area had walls on either side running parallel to the sides of the pile cap to allow the material to fail in a 2D fashion. The cellular concrete backfill for the 30° skew test had an average wet density of 29.6 pcf (474 kg/m3) and a compressive strength of 57.6 psi (397 kPa). The backfill for the 0° skew test had an average wet density of 28.6 pcf (458 kg/m3) and a compressive strength of 50.9 psi (351 kPa). The pile cap was displaced into the backfill area until failure occurred. A total of two tests were conducted, one with a 30° skew wedge attached to the pile cap and one with no skew wedge attached.It was observed that the cellular concrete backfill mainly compressed under loading with no visible failure at the surface. The passive-force curves showed the material reaching an initial peak resistance after movement equal to 1.7-2.6% of the backwall height and then remaining near this strength or increasing in strength with any further deflection. No skew effects were observed; any difference between the two tests is most likely due to the difference in concrete placement and testing.