Este trabalho apresenta uma revisão bibliográfica a respeito dos rejuntes para revestimento cerâmico. A nomenclatura internacional é explorada e os tipos de rejunte e seus empregos são enumerados. Para embasar o leitor sobre o reves-timento cerâmico, os principais conceitos a ele relacionados são exibidos de forma sucinta. Uma vez que o rejunte é um componente importante do revestimento ce-râmico, suas funções dentro desse subsistema são abordadas em detalhes. O as-pecto de alívio de tensões é amplamente comentado, uma vez que essa é uma função essencial do rejunte, particularmente no caso de fachadas. Ao final, são abordados os aspectos de preparo e aplicação dos rejuntes, particularmente os produtos cimentícios. O rejuntamento de locais específicos, como encontros com selantes e interfaces com aparelhos sanitários são detalha-dos com vistas à diminuição da ocorrência de manifestações patológicas futuras. No trabalho experimental, painéis em forma de laje revestidos com placas cerâmicas são submetidos à flexão até a ocorrência de desplacamento, objeti-vando detectar qual a influência da largura da junta e do tipo de argamassa ade-siva na ruptura do corpo-de-prova. Os resultados indicam que a largura das juntas de assentamento assumem importância apenas quando a argamassa adesiva apresenta alta resistência de aderência. / This study presents a bibliographical revision regarding the ceramic tile grouts. Here, the international nomenclature is explored and the types of grouts as well as its employments are enumerated. To base the reader on the ceramic tile cladding, its main concepts are shown succinctly. Being the grout an important component of the ceramic tile cladding, its functions in this subsystem are broached in details. The aspect of stress relief is widely mentioned, for this is an essential function of grout, particularly in the case of facades. In the end, the aspects of the preparation and the application of grouts are broached, particularly the cementitious products. The grouting of specific places such as meetings of sealants and interfaces with sanitary devices is detailed viewing the decrease of the occurrence of future problems. In the experimental study, panels in flagstone form tiled with ceramic plates are submitted to flexion until the occurrence of rupture of these panels, aiming to detect the influence of the joint thickness and of the type of the adhesive mortar in the rupture of the sample. The results indicate that the nesting joint thickness only assumes importance when the adhesive mortar presents high resistance of adherence.

Orientador: Gladis Camarini / Dissertação (mestrado) - Universidade Estadual de Campinas, Faculdade de Engenharia Civil, Arquitetura e Urbanismo / Made available in DSpace on 2018-08-10T20:33:15Z (GMT). No. of bitstreams: 1 Moreira-Lima_MariaMargaridaTeixeira_M.pdf: 1594548 bytes, checksum: 38f498b14a56cd02f47e608c6fa62728 (MD5) Previous issue date: 2007 / Resumo: A poeira gerada no processo de fabricação de materiais cerâmicos pode ser um agente de risco à saúde dos trabalhadores, em especial quando em sua composição houver a presença de polimorfos da sílica nas formas cristalinas do a-quartzo e da cristobalita. A exposição ocupacional à poeira respirável desses polimorfos pode ocasionar o aparecimento da silicose e de outras doenças associadas. Na indústria de revestimentos cerâmicos as informações sobre as características da poeira gerada nos seus processos e sobre a prevalência da silicose no setor são insuficientes para definir a magnitude do risco da exposição ocupacional à sílica. Este estudo de campo busca identificar parâmetros físicos e a concentração em sílica cristalina do material particulado suspenso no ar em indústrias de revestimentos cerâmicos para pisos e paredes. Foram selecionadas nove indústrias no município de Santa Gertrudes, no estado de São Paulo, com processo de fabricação por via seca, onde a matéria-prima principal é a argila vermelha proveniente da Formação Corumbataí. O estudo realizou-se por meio da observação sistemática das etapas do processo industrial, da coleta e análise de amostras da poeira presente nos ambientes de trabalho e da análise mineralógica da massa cerâmica manufaturada. As amostras de poeira foram analisadas por ravimetria e por difratometria de raios-X (DRX). Foi determinada a presença na poeira de partículas com tamanho na fração respirável (< 10 µm), sendo identificado o a-quartzo em 72% das amostras de poeira respirável analisadas. Não se encontraram outros polimorfos da sílica cristalina na poeira coletada. As avaliações realizadas indicaram concentrações de a-quartzo respirável entre 0,01 mg/m³ e 0,16 mg/m³, sendo a concentração média de a-quartzo respirável nos setores de moagem e de recepção de massa de 0,06 mg/m³, nos setores de prensas de 0,03 mg/m³, nas linhas de esmaltação de 0,02 mg/m³ e na preparação dos esmaltes e engobe de 0,09 mg/m³. Foi caracterizada por DRX a presença de minerais do grupo das micas, dos feldspatos e da esmectita na composição das massas cerâmicas analisadas, juntamente com a hematita e o quartzo, como mineral predominante / Abstract: Dust generated in the process of manufacturing ceramic materials may be a hazardous agent to the health of workers, especially when silica polymorphs in crystal forms of a-quartz and cristobalite are present in its composition. Occupational exposure to respirable dust of such polymorphs may lead to the onset of lung disease named silicosis and other associated diseases. In the ceramic wall and floor tiles industry data on the characteristics of dust generated in their processes and on the prevalence of silicosis in the sector are not sufficient to define the magnitude of occupational exposure risk to silica in this industry. This field study aims to identify physical parameters and the mass concentration and the composition in crystalline silica of airborne particulate material in industries of glazed ceramic tiles for floors and walls. Nine plants in Santa Gertrudes Municipality, São Paulo State, with dry manufacturing process, where the main raw material is red clay from the Corumbataí Formation have been selected. The study was conducted through systematic observation of the industrial process steps with dust generation, the collection and analysis of air samples from the environments and the mineralogical analysis of the raw ceramic bodies manufactured. Dust samples were analyzed with gravimetric and X-ray diffractometry (XRD) techniques. The air samples indicated that there was dust in the respirable fraction (< 10 µm) and the a-quartz was identified in 72% of the analyzed respirable dust samples. Other polymorphs of the crystalline silica were not found in the collected dust. The dust samples indicated concentrations of respirable a-quartz between 0.01 mg/m³ and 0.16 mg/m³ in the main stages of the process. The mean concentration of respirable a-quartz in the sectors of clay grinding was 0.06 mg/m³, in the pressing sectors it was 0.03 mg/m³, in the glazing lines it was 0.02 mg/m³ and in the preparation of enamels and engobe sectors it was 0.09 mg/m³. Minerals of the group of the micas, feldspars and smectite had been identified by XRD in the composition of all the ceramic masses, together with hematite and quartz, as the predominant mineral / Mestrado / Arquitetura e Construção / Mestre em Engenharia Civil

Made available in DSpace on 2014-12-17T14:07:06Z (GMT). No. of bitstreams: 1 RaimundoJSC_TESE.pdf: 1754370 bytes, checksum: 88d2811dd20d4c281cc4bc5a58cfc6fa (MD5) Previous issue date: 2010-11-16 / The red pottery industry in Piau? state is well developed and stands out at the national context for the technical quality of its products. The floor and wall tile industry, however, is little developed since the state has only one company that produces red clay-based ceramic tiles. This thesis aims at using the predominantly illitic basic mass of the above mentioned industry, with the addition of feldspar and/or kaolin residue in order to obtain products of higher technical quality. Kaolin residue consists basically of kaolinite, muscovite mica and quartz; the feldspar used was potassic. In this experiment, basic mass (MB) was used for experimental control and fifteen formulations codified as follows: F2, F4, F8, F16, F32, FR2, FR4, FR8, FR16, FR32, R2, R4, R8, R16 and R32. All raw materials were dry-milled, classified, formulated and then humidified to 10% water. Thereafter, test samples were produced by unixial pressing process in a rectangular steel matrix (60.0 x 20.0 x 5.0) mm3 at (25 MPa). They were fired at four temperatures: 1080?C, 1120?C, 1160?C, with a heating rate of 10?C/min during up to 10 min in an electric oven, and the last one in an industrial oven with a peak of 1140?C, aim ing to confirm the results found in laboratory and, finally, technological tests were performed: MEA, RL, AA, PA, TRF and PF. The results revealed that the residue under study can be considered a raw material with large potential in the industry of red clay-based ceramic tiles, since the results found both in laboratory and in the industry have shown that the test samples produced from the formulations with up to 4% feldspar and those produced with up to 8% feldspar and residue permitted a reduction in the water absorption rate and an increase in the mechanical resistance while those samples produced with up to 4% residue had an increase in the mechanical resistance when compared to those produced from the basic mass and that the formulation with 2% feldspar and residue presented the best technological properties, lowering the sintering temperature down to 1120?C / A ind?stria de cer?mica vermelha do Piau? ? bem desenvolvida e se destaca no contexto nacional pela qualidade t?cnica de seus produtos. J? a ind?stria de revestimento pouco se desenvolveu, visto que o estado possui uma ?nica empresa que produz revestimento de base argilosa vermelha. Esta tese tem por objetivo utilizar a massa b?sica predominantemente il?tica da ind?stria citada, adicionando ? mesma feldspato e/ou res?duo de caulim com o prop?sito de obter produtos de melhores qualidades t?cnicas. O res?duo caulim ? constitu?do basicamente de caulinita, mica moscovita e quartzo; o feldspato utilizado foi o pot?ssico. Para este experimento, utilizou-se a massa b?sica (MB) para controle experimental e quinze formula??es assim codificadas: F2, F4, F8, F16, F32, FR2, FR4, FR8, FR16, FR32, R2, R4, R8, R16 e R32. Todas as mat?rias-primas foram mo?das a seco, caracterizadas, formuladas, depois umidificadas a 10% com ?gua. Em seguida, foram confeccionados corpos-de-prova por prensagem uniaxial em matriz retangular de a?o (60,0 x 20,0 x 5,0) mm? a (24 MPa), os quais foram queimados em quatro temperaturas: 1080?C, 1120?C, 1160?C, com taxa de aqu ecimento de 10?C/min e patamar de 10 min em forno el?trico, e a ?ltima em forno a rolo industrial e pico de 1140?C com o objetivo de validar os resultados encontra dos em laborat?rio; por ?ltimo, foram realizados ensaios tecnol?gicos: MEA, RL, AA, PA, TRF e PF. Os mesmos mostraram que o res?duo estudado pode ser considerado como mat?riaprima de grande potencial para a ind?stria de pisos e revestimentos cer?micos de base argilosa vermelha, j? que tanto os resultados encontrados em laborat?rio como na ind?stria mostram que os corpos-de-prova produzidos a partir das formula??es com feldspato at? 4% e os produzidos com feldspato e res?duo at? 8% permitiram uma redu??o da absor??o de ?gua e aumento da resist?ncia mec?nica, sendo que os corpos-de-prova produzidos com at? 4% de res?duo tiveram aumento da resist?ncia mec?nica, quando comparados aos corpos-de-prova produzidos a partir da massa b?sica e que a formula??o com 2% de feldspato e res?duo apresentou melhores propriedades tecnol?gicas, reduzindo a temperatura de sinteriza??o para 1120?C

Made available in DSpace on 2014-12-17T14:58:05Z (GMT). No. of bitstreams: 1 DabneySGM_DISSERT.pdf: 1770376 bytes, checksum: 5e5a6ea101ce8878066e0256504f801a (MD5) Previous issue date: 2011-03-31 / In the industry of ceramic in Rio G. do Norte, tile stands out as the most manufactured product by this industry, being the intermittent kiln ab?bada and caieira the principal type of kiln used in burning. There was a need to make a study of the influence exerted by the type of kiln in which tiles are burnt in their thermo physical properties. The analysis started with 24 raw samples of tile, which was split in two groups of 12 samples and burnt in Ab?bada and Caieira kiln. Besides that, it was made study of the tax of heat transfer to the environment (for each kiln). After having been burnt the samples were taken for laboratory analysis. The properties verified were impermeability, determination of dry mass, absorption of water, the load of bending rupture and its geometric characteristics, the tests were conducted following the currents standards. The tests were carried out according to the ABNT - NBR 15310. The calculation of the rate of heat transfer showed that the ab?bada kiln is more efficient than the Caieira, however the results of tests on the samples revealed no superiority of one over another sample. So the furnace had no influence on the performance of the ceramic tiles / Na ind?stria de cer?mica vermelha a telha desponta como o produto mais fabricado pela ind?stria de cer?mica do Serid?/RN, sendo os fornos intermitentes do tipo ab?bada e caieira os mais utilizados para a queima destas telhas. Verificou-se a necessidade de se fazer um estudo da influ?ncia exercida pelo tipo de forno no qual as telhas s?o queimadas nas suas propriedades termof?sicas, mec?nicas e geom?tricas. Sendo selecionadas 24 amostras de um mesmo processo de fabrica??o, no entanto estas foram posteriormente separadas em dois lotes de 12 unidades e levadas a queima no forno caieira e ab?bada. ? importante ressaltar que os corpos de prova n?o fazem parte do processo produtivo das cer?micas de onde foram utilizados os fornos para queima, ou seja, as cer?micas gentilmente cederam seus fornos para a realiza??o do experimento. Foi realizado um estudo da taxa de transfer?ncia de calor ao meio ambiente para cada tipo de forno. Assim as amostras ap?s serem queimadas foram levadas para an?lise em laborat?rio. As propriedades verificadas foram ? impermeabilidade, determina??o da massa seca e da absor??o da ?gua, determina??o da carga de ruptura ? flex?o e de suas caracter?sticas geom?tricas. Os ensaios foram realizados segundo a norma ABNT - NBR 15310. O calculo da taxa de transfer?ncia de calor mostrou que o forno ab?bada ? mais eficiente que o caieira, no entanto os resultados dos ensaios nas amostras mostraram que n?o houve superioridade de uma amostra sobre outra, assim os fornos n?o tiveram influ?ncia no desempenho das telhas

Les « Maîtres de Tabriz » ont suscité un vif intérêt chez les chercheurs. Ces céramistes, qui ont orné des édifices ottomans au 15ème et 16ème siècle, demeurent pourtant mystérieux à bien des égards. L’absence de biographies rend leur identification incertaine et engendre par conséquent de nombreuses théories sur leur origine historique et géographique. Concrètement, ces maîtres ne sont connus qu’à travers leur nom figurant dans les inscriptions monumentales ou dans les archives ottomanes. Une investigation dans les textes anciens a alors été essentielle pour combler le manque d’indices. Cependant, certaines de ces sources écrites ont fait l’objet d’extrapolations et de spéculations aléatoires. Pourtant, elles sont considérées comme des éléments probants, ce qui fausse évidemment l’identification de ces céramistes. Il a été primordial de revenir sur les éléments d’identification. La relecture des sources primaires permet en effet de dégager les notions concrètes et d’écarter les hypothèses infondées. Tel est l’enjeu de la première partie de cette étude qui met en évidence les connaissances que l’on possède des « Maîtres de Tabriz ». La deuxième partie est consacrée à l’analyse technique et ornementale des céramiques architecturales. Les œuvres des « Maîtres de Tabriz » sont relativement bien connues. Elles ont fait l’objet de nombreuses publications, mais ont souvent été abordées de manière transversale. Cette étude propose une nouvelle approche en mettant en relation la production de chacun des quatre groupes de céramistes. Cette démarche permet ainsi de saisir l’évolution de cette production tout en mettant en avant les corrélations et les disparités artistiques. / The « Masters of Tabriz » generate high interest among researchers. These ceramists, who decorated ottoman buildings in the 15th and 16th centuries, remain mysterious in many respects. The absence of biographies makes their identification uncertain and hence leads to many different theories about their historical and geographical origins. In reality, these masters are only known for their names found on monumental inscriptions and from ottoman chancery documents. Thus, investigation into ancient texts became essential to fill in the lack of evidence. However, some of these written sources have led to extrapolations and uncertain speculations. Yet these have been accepted and considered as conclusive elements, which obviously misrepresent these master ceramists. It is thus essential to return to the elements of identification. Rereading primary sources written in Arabic, Persian and Ottoman gives evidence to concrete notions and dismisses unfounded suppositions. As the shadow zones round them tend to lead to myths, the objective of the first part of this study is to rectify the knowledge in our possession of the “Masters of Tabriz”.The second part consists of a technical and ornamental analysis of the architectural ceramic tiles. The productions of the “Masters of Tabriz”, principally found in Bursa, Edirne, Istanbul and Jerusalem, are relatively well known. They have been the subject of many publications, but have often been treated transversally. This study offers a new approach, comparing the productions of the four groups of ceramists. This procedure brings to light the progression of this production as it focuses on the artistic correlations and disparities.

This thesis is focused on the possibilities of the utilization of the fludized fly ash in ceramic technology, especially in the field of brick manufacturing and ceramic tiles. There were used fly ashes from thermal power plants in Hodonín, Ledvice and Tisová. Fluidized fly ash can be used for manufacturing of building materials. There hasn’t been done extensive research in this area. One of the problem is sulphur dioxide leakage during burning. The work describes the behaviour of fluidized ash during firing. The attention is focused on air pollution of sulphur dioxide. The production of SO2 is controlled so that the aim of the work is to find a way how to avoid leaking. It was proved that addition of sodium ions causes the formation of minerals hauyne and nosean during firing. Also is described the behaviour of the fly ash-soil mixtures. The anhydrite decomposition temperature is lower than in pure fly ash. In the end is fluidized ash applied for the production of dry pressed ceramic tiles. This ash can be used in ceramic technology. However, despite the interesting results there are number of problems that need to be solved.

Konformen har tidigare under arkitekturhistorien ofta använts för att skapa rum enligt en cellulär logik. Projektet ämnar ompröva användandet av konformen för att organisera rum, i det här fallet applicerat på en konsthall i Solna, genom att gå utanför enbart ett repetitivt arrangemang av vertikala koniska moduler för att uppnå en variation av skalor och riktningar som spänner från stora horisontella koniska rum till mer intima småskaliga vertikala rumsbildningar. Rummen skapas genom en adderande process där koner genomskärs med varandra och med plana element som adderas i operationen. Detta tillåter på så sätt en samexistens av två olika rumsliga logiker vilket leder till en komplex och tillåtande arkitektur som kan svara mot behoven i programmet och som även lyfter fram och förstärker formen hos byggnaden. Projektet utforskar även möjligheterna med att använda konen i egenskap av att vara en enkelkrökt yta och dess betydelse för digital modellering, ritningar och konstruktion. / The cone in architecture has often been used to shape and generate space with a cellular structural logic. This project reconsiders the use of the cone for organizing space, in this case applied on an Art Centre in Solna, going beyond the mere repetitive logic of conic modules, to allow for a variety of scales and directions, ranging from large span horizontal conic spaces to more intimate smaller scaled vertical conic rooms. The spaces are created through an additive process of intersecting cones with planar elements added into the operation, thus allowing the coexistence of two spatial logics, leading towards a manifold and allowing architecture that can handle the requirements of the program and that reinforces the perception of the shape. The project also explores the possibilities of the cone as a single curved unfoldable surface and it’s implications on digital model making, drawing and physical construction.

This thesis presents a case of study of the development and performance analysis of a surface grading application with real-time compliance. We address the issue of spatial and temporal uniformity in the acquisition system. In a surface grading application it is crucial to ensure the uniform response of the system through time and space. All the results presented for surface grading were obtained using real data from the ceramic tile industry. The VxC TSG database is public and can be accessed at www.disca.upv.es/vision/vxctsg. We present a method based on soft colour-texture descriptors computed in perceptually uniform colour spaces. The method is parameterized and the involved factors are studied using two statistical procedures; experimental design and logistic regression. Although it is not a new theoretical contribution, we have found and demonstrate that a simple set of global colour and texture statistics, together with well-known classifiers, are powerful enough to meet stringent factory requirements for real-time and performance. Also the method is compared with two other approaches from the scientific literature; Colour Histograms and Centile-LBP. Finally, we explore the method's capacity for on-line inspection in a study of real-time compliance and parallelization. / López García, F. (2005). Real-time surface grading of ceramic tiles [Tesis doctoral no publicada]. Universitat Politècnica de València. https://doi.org/10.4995/Thesis/10251/1909 / Palancia

Diploma thesis is about design and making of execution project for office city building which is located in Nový Bydžov. The building is located in the late brownfield area of Dufek´s wood manufacture, which is on the south part of Nový Bydžov. The building has four above ground floors and one below ground floor. The building shape is rectangular of dimensions 53,02 x 17,62 m. On the south, west and east is the façade from height of second floor slightly cantilevered. On the east part the edge of cantilevered façade duplicate slopping edge of the bottom land and it creates wonderful but economical shape. The height of the building from the ground is 14,5 m. The shape of roof is flat, covered with the mPVC foil and gravel mound. Façade which covering the first ground floor is made of polystyrene with thin layer of plaster which creates building plinth. Top cantilevered façade is made of ceramic tiles of dimensions 1200 x 600 mm which are suspended behind the air layer. The ceramic tiles are light brown color. In the bottom part are glazed areas of rectangular and square shapes to create the open feeling in the ground floor. In the rear part is designed coffee bar with nice outside wooden terrace. Windows in the top cantilevered part of the façade are the circular shape and extend the architectural impression of the building. All windows are in the same color of dark blue. The steel parts of the building are also dark blue color. In the bellow ground floor are designed underground parking lot with the maximum capacity 29 cars and technical equipment. In the first floor above ground are designed reception, big lecture hall, exhibition hall, coffee bar with terrace and toilets. In the second floor above the ground are offices, computer room and HVAC equipment. In the third above floor are offices, conference hall, and IT equipment. In the fourth floor above the ground are also offices, maintenance room and storage of furniture.

The subject of this thesis is the preparation and organization of construction of residential buildings in Štětí. In the technological regulations deal with all the layers of flooring from the ceiling construction in residential buildings. The objects are hard floors. For floor coverings will be used PVC roofing, ceramic tiles and concrete coating. It will be used for machining of concrete. Next, I will discuss technological instruction, timing, valuation of all technological stages, construction site equipment, health and safety at work. Also here describe the proper allocation of construction processes into sub-processes to technological stage of completion of work most effectively achieve the objective.