No description available.

No description available.

No description available.

Li-ion batteries (LIB) are used in many applications because of their high-power/energy density, long life cycling, and low self-discharge rate. The use of LIB continues to grow every day, and the necessity for proper safety standards grows as well. A key aspect for safe utilization of LIB is determining their safety and remaining useful life (RUL). Battery characteristics degrade over time under normal and extreme operating conditions and modeling the electrochemical processes can improve RUL estimations. Extreme operating conditions such as abnormal temperatures and charge/discharge rates are believed to exacerbate the rate of degradation. Li-ion batteries are also susceptible to mechanical damage, which may lead to an electrical short. In severe cases, mechanical damage causes a thermal run away, and possibly explosions or fires. In the event of a car accident, battery packs can be damage without an electrical short or immediate thermal run away. Currently, there is no reliable batt / Mechanical Engineering

<p dir="ltr">Microfluidic techniques have been widely adopted in biomedical research due to the pre- cise control of fluids, small volume requirement, low cost and etc, and have boosted the development of biomolecular interaction analysis, point-of-care diagnostics, and biosensors.</p><p dir="ltr">Protein-protein interaction plays a key role in biological, biomedical and pharmaceutical research. The technical development of biosensors, new drugs and vaccines, and disease diagnostics heavily rely on the characterization of protein-protein interaction kinetics. The current gold standard assays for measuring protein-protein interaction are surface plasmon resonance (SPR), and bio-layer interferometry (BLI). These commercial devices are accurate but expensive, however.</p><p dir="ltr">Here, I have developed new microfluidic techniques and models in protein-protein in- teraction kinetics measurement, rotational diffusion coefficient modeling, electrochemical impedance spectroscopy-based biosensors, and two-phase porous media flow models. Firstly, I applied particle diffusometry (PD) in the streptavidin-biotin binding kinetics measurement, utilizing a Y-junction microchannel. Secondly, to reduce solution volumes used in an analysis experiment, I designed a low-volume chip and coupled it with PD to measure the binding kinetics of human immunodeficiency virus p24 antibody-antigen interactions. Thirdly, con- sidering the Brownian motion of the non-symmetric particles, I developed a new model to efficiently compute particles’ rotational diffusion coefficients. Fourthly, to make economic biosensors to detect multiple biomarkers, I created a new chip, enabling hundreds of tests in a single droplet (∼ 50 μL) on one chip. Finally, to understand the liquid flow in porous media, such as nitrocellulose in lateral flow assays, I built a new two-phase porous media flow model based on the Navier-Stokes equation and compared it with experiments. These techniques and models underwent rigorous experimental and computational validation, demonstrating their effectiveness and performance.</p>

Conducting vertical nanopillar arrays can serve as three-dimensional nanostructured electrodes with improved performance for electrical recording and electrochemical sensing in bio-electronics applications. However, vertical nanopillar-array electrodes made of inorganic conducting materials by conventional nanofabrication approach still faces challenges in high manufacturing costs, poor scalability, and limited choice of carrier substrates. Here, we report a new type of conducting nanopillar arrays composed of multi-walled carbon nanotubes (MWCNTs) doped polymeric nanocomposites, which are manufactured over the wafer-scale on both rigid and flexible substrates by direct nanoimprinting of perfluoropolyether nanowell-array templates into uncured MWCNT/polymer mixtures. By controlling the MWCNT ratios and the annealing temperatures during the fabrication process, MWCNT/polymer nanopillar arrays can possess outstanding electrical properties with high DC conductivity (~4 S/m) and low AC electrochemical impedance (~104 Ω at 1000 Hz). Moreover, by electrochemical impedance spectroscopy (EIS) measurements and equivalent circuit modeling-analysis, we can decompose the overall impedance of MWCNT/polymer nanopillar arrays in the electrolyte into multiple bulk and interfacial circuit components, and thus can illustrate their different dependence on the MWCNT ratios and the annealing temperatures. In particular, we find that a proper annealing process can significantly reduce the anomalous ion diffusion impedance and improve the impedance properties of MWCNT/polymer nanopillars in the electrolyte. / Master of Science / Conducting vertical nanopillar arrays can serve as three-dimensional nanostructured electrodes with improved performance for electrical recording and electrochemical sensing in nano-bioelectronics applications. However, vertical nanopillar-array electrodes made of inorganic conducting materials by conventional nanofabrication approach still faces challenges in high manufacturing costs, poor scalability, and limited choice of carrier substrates. Compared to conventional nanofabrication approaches, nanoimprint lithography exhibits unique advantages for low-cost scalable manufacturing of nanostructures on both rigid and flexible substrates. Very few studies, however, have been conducted to achieve the scalable nanoimprinting fabrication of conducting nanopillar arrays made of MWCNT/polymer nanocomposites. Here, I'm reporting a new type of conducting nanopillar arrays composed of multi-walled carbon nanotubes (MWCNTs) doped polymeric nanocomposites, which can be manufactured over the wafer-scale on both rigid and flexible substrates by direct nanoimprinting of the perfluoropolyether nanowell-array template into uncured MWCNT/polymer mixtures. We find that the nanoimprinted conducting nanopillar arrays can possess appealing electrical properties with a high DC conductivity (~4 S/m) and a low AC electrochemical impedance (~104 Ω at 1000 Hz) in the physiologically relevant electrolyte solutions (1X PBS). Furthermore, I've conducted a systematic equivalent circuit modeling analysis of measured EIS results to understand the effects of the MWCNT ratios and the annealing temperatures on the impedance of different bulk and interfacial circuit components for MWCNT/polymer nanopillar arrays in the electrolyte.

<p dir="ltr">Portable sensing enables an enhanced form of disease monitoring due to its accessible form-factors, low costs, and insights into user health, along with enhanced detection methods due to its many use cases for at-home or in-field applications. To that end, electrochemistry has been a widely used technique in characterization, detection, and diagnostics. Electrochemical Impedance Spectroscopy (EIS) is an electrochemical technique that enables electrode surface characterization through changes in impedance across a given frequency range making it sensitive to interactions at the electrode surface and enabling the detection and quantification of analytes. While EIS has been traditionally limited to benchtop potentiostats, advancements in integrated circuits (ICs) have since enabled the miniaturization of potentiostats for at-home or field applications. However, implementation of EIS in a portable format is still limited by discontinuous measurements, high cost, or designs not fit for portability. This work revolves around the development of a miniaturized potentiostat that can implement EIS to better accommodate the need for miniaturized sensing platforms. My design uses the AD5941 IC which is a single-chip potentiostat analog-front-end enabling a small form-factor that fits in the palm of the user’s hand. The device was able to characterize a resistor-capacitor circuit with errors as low as 0.33% and quantify the concentration of a redox active compound with a 6.2% error, providing agreeable results with a commercial benchtop potentiostat and demonstrating our device’s potential for diagnostic applications. Our working frequency range of 200 kHz – 0.15 Hz, coupled with high system configurability and a cost of $50 makes our device an accessible option for at-home and portable applications. Future work to implement truly wireless functionalities, such as WiFi or Bluetooth Low Energy, along with experimental testing of biological substances will create a truly robust platform for portable diagnostic and sensing applications.</p>

This study involved a comparative investigation of chloride-induced corrosion detection techniques on loaded reinforced concrete slabs which were exposed to deicing salts and wetting-drying cycles to simulate typical aggressive environments in cold climates. The studied techniques involved linear polarization technique, galvanostatic pulse technique, electrochemical impedance spectroscopy, half-cell potential and concrete electrical resistivity mapping. The results showed that concrete quality and moisture content have a direct effect on corrosion activity, and these properties are represented well with concrete electrical resistivity. The galvanostatic pulse technique was shown to correlate well with electrochemical impedance spectroscopy, which was used as a benchmark for corrosion rate measurements in this study; however, the galvanostatic pulse technique was not capable of detecting corrosion activity in saturated concrete accurately. The results of this research do not support the criteria provided by the ASTM C876-09 standard for using half-cell potentials to estimate the probability of reinforcing steel corrosion in reinforced concrete structures.

Ce travail concerne l'étude du comportement vis-à-vis de la corrosion de deux alliage d'aluminium : l'alliage 2024 (AA 2024 T351) et l'alliage 7075 (AA7075 T7351) et de l'aluminium pur, utilisé comme référence, dans une solution de Na2SO4 0,1 M à l'aide de mesures électrochimiques (courbes de polarisation, courbes de Levich et spectroscopie d'impédance) avec des électrodes à disque tournant. Comparativement aux travaux de la littérature, des données quantitatives sur les processus anodique et cathodique qui se produisent sur les deux alliages ont été obtenues. La première partie de la thèse est consacrée à la caractérisation microstructurale des deux alliages : taille, composition chimique des précipités et fraction surfacique occupée par les différentes phases. La seconde partie présente les résultats d'impédance obtenus au potentiel de corrosion pour différents temps d'immersion et différentes vitesses de rotation. A ce potentiel, le comportement des matériaux est essentiellement contrôlé par le film passif. Les diagrammes d'impédance présentent une dispersion en fréquence, exprimée en termes de « constant phase element (CPE) ». Ce comportement a été analysé à l'aide d'un modèle physique qui permet de montrer une distribution de résistivité dans l'épaisseur des films d'oxyde. Dans la dernière partie, une attention particulière a été portée à l'analyse de la réaction cathodique à la surface des deux alliages qui est à l'origine de leur dégradation importante. La réduction de l'oxygène se produit principalement sur les particules intermétalliques. De façon surprenante, la densité de courant cathodique est nettement plus faible pour l'alliage 7075 qui présente une plus grande surface couverte par les particules. Il a été montré que pour l'alliage 2024, la réaction cathodique est contrôlée par le transport de matière par diffusion convective sur de petites électrodes alors que pour l'alliage AA 7075, la majeure partie des particules, de très petite taille, se comporte comme des microélectrodes pour lesquelles le courant est fixé par la diffusion sphérique, indépendante de la convection. / This work concerns the study of behavior the corrosion of two aluminum alloy: the alloy 2024 (AA 2024 T351) and 7075 (AA7075 T7351) and pure aluminum, used as reference, in a solution of 0.1 M Na2SO4 using electrochemical measurements (polarization curves, curves Levich and impedance spectroscopy) with rotating disk electrodes. Compared to published studies, quantitative data on the anodic and cathodic processes occurring on the two alloys were obtained. The first part of the thesis is devoted to the microstructural characterization of two alloys: size, chemical composition of precipitates and surface fraction occupied by the different phases. The second part presents the results of impedance obtained at the corrosion potential for different immersion times and different speeds. At this potential, the behavior of materials is mainly controlled by the passive film. The impedance diagrams exhibit a frequency dispersion, expressed in terms of "constant stage element (CPE)." This behavior was analyzed using a physical model which allows to show a distribution of resistivity in the thickness of oxide films. In the last part, special attention was paid to the analysis of the cathodic reaction on the surface of the two alloys that is causing their degradation. The oxygen reduction occurs mainly on the intermetallic particles. Surprisingly, the cathode current density is significantly lower for the alloy 7075 which has a greater surface area covered by the particles. It was shown that for 2024 alloy, the cathodic reaction is controlled by material transport by convective diffusion of small electrodes, while for the alloy AA 7075, most of the particles, very small, behaves as microelectrodes for which the current is set by the spherical diffusion, independent of the convection.

Les aciers inoxydables martensitiques sont utilisés dans l'industrie aéronautique où de hautes propriétés mécaniques sont requises. Cependant, dû à leur faible teneur en chrome, ils sont relativement sensibles à la corrosion localisée et particulièrement à la corrosion caverneuse qui se développe en milieu confiné. Tout d'abord, le comportement électrochimique de l'acier inoxydable martensitique X12CrNiMoV12-3 a été étudié dans une solution neutre et chlorurée (NaCl 0,1 M + Na2SO4 0,04 M) en plein bain. Des mesures électrochimiques (courbes de polarisation et mesures d'impédance) couplées à des analyses de surface par XPS ont permis de caractériser les films passifs formés pour différentes conditions. Les résultats obtenus ont permis de montrer le rôle important joué par l'oxygène dissous sur la formation et/ou la modification du film passif pendant l'immersion dans l'électrolyte. Les diagrammes d'impédance obtenus au potentiel de corrosion et en milieu aéré sont caractérisés par deux constantes de temps qui ont été attribuées au film passif (hautes fréquences) et au transfert de charges (basses fréquences). L'analyse de la partie hautes fréquences des diagrammes d'impédance électrochimique à l'aide du modèle en loi de puissance a permis de montrer de faibles variations de l'épaisseur des films pendant l'immersion. Des mesures électrochimiques ont ensuite été réalisées à l'aide du montage de la cellule à couche mince qui permet de travailler avec des épaisseurs d'électrolyte rigoureusement contrôlées. Les essais réalisés ont montré l'aptitude à la repassivation de l'acier inoxydable martensitique dès qu'il est en contact avec l'oxygène dissous en particulier pour des faibles épaisseurs d'électrolyte (inférieur à 100 µm). Lorsque le milieu est confiné entre deux parois en acier afin de reproduire une situation de corrosion caverneuse, il a été montré la corrosion est fortement accélérée lorsque l'épaisseur d'électrolyte est faible (inférieur à 500 µm). / Martensitic stainless steels are mainly used for applications where high mechanical performance is required. However, due to the low chromium content, they are relatively sensitive to localised corrosion, and particularly, to crevice corrosion encountered in confined environments. First, the electrochemical behavior of X12CrNiMoV12-3 martensitic stainless steel has been studied in a bulk neutral chloride solution (0.1 M NaCl + 0.04 M Na2SO4). Electrochemical measurements (polarisation curves and impedance measures) and XPS surface analysis were performed in order to characterise the passive films formed under different experimental conditions. The results showed the important role of dissolved oxygen to form and/or modify the passive film during immersion in electrolyte. The impedance diagrams are characterised by two time constants wich are attributed to passive film response (high frequency range) and to charge transfert resistance (low frequency range). The analyse of the high frequencies part of the diagrams by using the "power law model" showed low evolution of passive films thickness during immersion. Then, electrochemical measurements were perfomed in confined environments by using a thin layer cell where the electrolyte thickness were rigourosly adjusted. The measurements showed that the martensitic stainless steel is in passive state even for low electrolyte thickness (inferior in 100 µm). When the electrolyte is confined between two stainless electrodes in order to reproduce the same conditions find during crevice corrosion, the corrosion is sharply accelerated when the electrolyte thickness is above 500 µm