The effects of thermal loads on steel bridges are not well understood. Although thermal effects are discussed in the AASHTO specifications, the appropriateness of the recommended thermal gradients is questionable. Thermal effects on the bridges can impact the design of the steel superstructure, the support bearings, and even the bridge piers. Previous field monitoring of steel trapezoidal box girder bridges has shown that thermal stresses on the order of ±5 ksi were not uncommon under regular daily thermal cycles. Stresses induced during annual thermal cycles may be potentially larger than those during daily thermal cycles. Recent data has shown that the bearings that are to allow the girders to expand and contract freely due to thermal movements are not frictionless. Because of the bearing friction, the supporting piers must flex to accommodate the bridge movements. In curved girder applications, questions have been raised by designers and contractors regarding the proper orientation of guided bearings. This research study includes field measurements, laboratory tests and finite element parametric analyses. The bearings of nine bridges in the Houston area have been instrumented and monitored for more than a year to measure bearing movements due to changes in temperature. Instrumentation of the steel girders on one of the Houston bridges was made utilizing thermocouples and vibrating wire strain gages to measure temperature distribution and thermal stresses. In addition, strain gages and thermal couples were applied to the steel girders and concrete bridge deck on a simple twin box girder bridge located at the Ferguson Structural Engineering Laboratory in Austin, Texas. The data from the field monitoring and laboratory tests were used to validate a finite element model. Based on this model, a detailed parametric study was conducted to investigate the effects of bridge configuration. It is found that under the given weather conditions, the most critical thermal loads are achieved under the following bridge configurations: N-S bridge orientation, shorter lengths of the concrete deck overhang, deeper steel girder webs, thinner concrete decks, and larger spacing between two box girders. To evaluate the effect of environmental conditions and obtain extreme thermal loads for design purposes, the most critical configuration of bridge sections was modeled for thermal analysis with Texas weather data from 1961 to 2005 as the input environmental conditions. Four cities were considered to bound Texas weather conditions. Based on the thermal analyses, a 45-year sample data of thermal parameters were used to describe the temperature field over a section. Extreme value analyses of the sample data were performed to obtain the relationship between thermal loads and return periods. The thermal loads with 100-year return period were compared to the ones suggested by AASHTO. The thermal loads with 100-year return period were used to investigate structural response. The effect of bearing orientation and the point of fixity were studied. A rigid body model was proposed to estimate thermal movements at the ends, which matched those obtained from field monitoring and finite element analysis. The maximum possible thermal stresses were also evaluated. Design suggestions are put forward based on the analysis. / text

published_or_final_version / Civil Engineering / Master / Master of Philosophy

Sugarcane plants (cultivar NCo376) were studied to assess the effects of temperature and season (spring and autumn equinox) on the morphological and physiological response of stalk components. Plants were grown from single-eyed setts for ca. five months and then placed into three temperature controlled glasshouses (22/12°C (C), 27/17°C (W) and 32/22°C (H) day/night temperatures). The plants were sampled twice weekly over a one month period., and intemodes 4, 6 and 10 of the primary haulms of each plant sampled for growth and sugar analysis. During spring, the leaf emergence rates were 0.0303, 0.1095 and 0.1682 leaves d(-1) at temperatures C, W and H, respectively; and 0.0327, 0.0824 and 0.113 leaves d(-1) in autumn. The phyllochron intervals were 114°Cd in spring and 147°Cd in autumn. Highest green leaf blade area of the primary haulms was achieved at H (438.0 and 511.7 cm2 in spring and autumn, respectively). The stalk extension rates were 1.22, 1.02, 0.38 cm d(-1) (spring) and 1.35, 0.98, 0.45 cm d(-1) (autumn), respectively, in descending order of temperature. Total biomass and stalk biomass per plant were not affected by temperature, despite the differences in stem elongation. Internodes of plants at C were shorter but thicker and heavier than the comparable internodes of plants at W and H. In autumn, the mature internode sucrose concentrations were 35.5, 29.2 and 25.5% at C, W and H, respectively; corresponding to mean RS% of 5.7, 9.8 and 13.3%, and fibre % of 58.8, 61.1 and 61.3%, at the respective ascending order of temperature. Sucrose % in the mature internodes in spring were 27.8, 20.9 and 19.9% at C, W and H, respectively; corresponding to RS% of 5.9, 9.76 and 10.9% and fibre % of 66.3, 69.4 and 69.2% at the respective ascending order of temperature. Temperature effect on the concentration of the stalk components of the immature internodes was in general not significant. Sucrose partitioning coefficients in the mature internodes were 0.25, 0.21 and 0.20 in spring and 0.50, 0.32 and 0.21 in autumn (at C, W and H, respectively). Data that resulted from this study, which is isolated to temperature and cultivar NCo376 can be used in models of sugarcane that simulate leaf appearance and senescence, assimilate partitioning between leaf and stalk and assimilate partitioning between the stalk components namely sucrose, reducing sugars and fibre. / Thesis (M.Sc.)-University of KwaZulu-Natal, Pietermaritzburg, 2005.

This thesis investigates the effects of low temperatures on Silicon Germanium (SiGe) Hterojunction Bipolar Transistors (HBT) BiCMOS technology. A comprehensive set of dc measurements were taken on first, second, third and fourth generation IBM SiGe technology over a range of temperatures (room temperature to 43K for first generation, and room temperature to 15K for the rest). This work is unique in the sense that this sort of comprehensive study of dc characteristics on four SiGe HBT technology generations over a wide range of temperatures has never been done before to the best of the authors knowledge.

Thesis (MSc (Horticulture))--University of Stellenbosch, 2006. / A growing number of fruit producers in warm areas are adopting the use of overtree evaporative cooling (EC) as a technique to reduce sunburn and enhance colour development of red or blushed fruit. Because fruit do not have efficient mechanisms of utilising and/or dissipating solar radiation, fruit surface temperature may rise 10 – 15oC higher than the ambient air temperature, making them very susceptible to sunburn. Sunburn negatively affects the appearance of the fruit, and they cannot be sold for fresh market consumption, which receives the highest prices. Evaporative cooling uses a sprinkler system to cool the trees from above. Energy needed to evaporate the water is extracted from the fruit skin, cooling the fruit down. The air around the trees is cooled, and a more favorable microclimate is created in the orchard. Producers have also found that the use of EC just prior to sundown and sometimes around sunrise has improved colour development on red apples (especially early varieties) before harvest. In this study, two apple (‘Cripps’ Pink’ and ‘Royal Gala’) and two pear (‘Rosemarie’ and ‘Forelle’) cultivars under EC were compared with control fruit in terms of maturity, colour, sunburn and concentrations of polyphenolics in the skin. Two EC treatments were given; early application starting from the second week in December, and late application starting two to four weeks before harvest. Photosynthetic responses were measured, as well as fruit and leaf temperatures. Underlying physiological responses of trees and fruit to EC were investigated, particularly the phenomenon of acclimation and the potential for colour development and heat stress. Fruit surface temperature of fruit under EC was found to be significantly lower than control fruit. In both apple cultivars a significant increase in fruit skin anthocyanin concentration and a decrease in phenolic content was found as the season progressed. In both pear cultivars there was a significant decrease in both anthocyanin and phenolic. No significant differences were found in anthocyanin content between treatments in either the apple or pear cultivars. In both apple cultivars a higher phenolic content was found in the peel of the EC treatments. A decrease of up to four percent in leaf and fruit surface temperature was found under EC. No significant difference in trunk circumference was found in any of the cultivars. The late EC treatment in ‘Cripps’ Pink’ had a significantly faster rate of budbreak than the control and early EC treatments. Significantly higher transpiration was observed in leaves under EC. ‘Royal Gala’ fruit under EC had less sunburn than control fruit. Unfortunately the system broke down on a hot day, causing more sunburn on ‘Cripps’ Pink’ fruit under EC. Heat tolerance of apple fruit grown under EC was evaluated in ‘Cripps’ Pink’ and ‘Royal Gala’ by determining the maximum quantum yield of chlorophyll fluorescence (Fv/Fm). Measurements were also made 12 hours after the heat treatments to determine recovery. ‘Cripps’ Pink’ fruit from both EC treatments, but particularly the early EC treatment, were less resistant to heat stress than control (non-EC) fruit at the “threshold” air temperature of 45°C. Apples were able to recover from heat treatments in the range of 32-38oC fruit surface temperature, and generally also recovered fully after 43-45°C fruit surface temperature when exposure did not exceed four hours. This knowledge could be helpful in the management of sunburn, for example when determining the threshold temperature for the activation of evaporative cooling treatments. Knowledge about the various effects evaporative cooling and the subsequent lowering of ambient temperatures has on fruit trees and fruit could contribute greatly to producers’ ability to grow high quality fruit. EC can be used successfully for controlling sunburn and increasing fruit colour, but the system needs to be controlled very carefully and care should be taken that it does not fail on a hot day, as it did during this study.

Experimental results of damage development in and mechanical response of heat-treated NicaloniCAS-II laminates subjected to monotonic flexure and axial loading and to cyclic tensile loading are reported. The specimens were subjected to post-processing heat treatments at 900°, 1000°, and l100°C in air for 100 hours. Changes at the fiber/matrix interface/interphase due to post-processing heat treatments were also characterized. The combined effect of fiber debonding and transverse matrix cracking in both 90° and 0° plies plays an important role in damage development in [0/90]₄₅ Nicalon/CAS-II laminates, especially in developing the secondary damage modes such as longitudinal matrix cracking and delamination. Frictional wear effects found in cyclically loaded specimens may be responsible for the observed temperature profiles during the intermediate stage of fatigue life. It is also believed that frictional wear is critical to the failure of notch sensitive fibers. Different damage modes such as "brittle" matrix crack propagation and "quasi-brittle" matrix crack propagation were observed in heat-treated specimens. Results obtained from microanalysis using an analytical scanning transmission electron microscope equipped with an energy dispersive spectrometer, and microindentation indicated that the changes of damage and failure modes were directly related to the changes of characteristics at the fiber/matreix interface/interphase. / Ph. D.

No description available.

Chickens, being open thermodynamic systems, maintain a constant exchange of energy and matter with their surrounding environment. In order to avoid reaching thermodynamic equilibrium with the environment the bird makes use of homeostatic mechanisms. These ensure the reduction of the entropy of the system to values that guarantee its integrality. The thermoregulatory response is a major component of the homeostatic machinery of living systems. This induces modifications of physiological parameters of the bird, taking the system “bird” to a new steady state. The achievement of this new state is possible only if the thermoregulatory mechanisms of the birds are able to counteract the environmental demand/burden. A successful thermoregulatory response depends not only on the achievement of that steady state, but also on the compatibility of the value of those parameters with life (especially regarding the value achieved by body temperature) as well as on the time of exposure to the environmental perturbation. Based on those premises, this thesis presents a mechanistic analysis of the thermal interaction between a broiler and its surroundings. The first section of the document introduces the reader to the general concepts of thermodynamics of living systems and physics of heat exchange. The second use mechanistic simulation techniques to represent the environment, the thermal and thermoregulatory properties of a broiler chicken and the interaction between bird and environment. Finally, the third section describes a conceptual simulation model able to predict, over a given period of time, the response of a bird to environmental conditions above those associated with least thermoregulatory effort. Various simulation exercises are reported, the objectives being to study the behaviour of certain variables and to question the validity of current theories of thermoregulation in environmental physiology. / Thesis (Ph.D.)-University of KwaZulu-Natal, Pietermaritzburg, 2010.

Onions are widely produced within the tropics, but little scientific research has been done specifically on the Eritrean cultivars, like Hagaz Red 1 and 2 (HR I, and HR 2). Many onion cultivars are limited in their range of adaptation due to the combined effects of photoperiod and temperature. A priority for research on the crop was to elucidate the local crop's growth response to environmental conditions, particularly temperature and daylength. The Eritrean cultivars HR I and 2 and an American (Louisiana) cultivar Red Creole (RC) grown in South Africa were grown in growth rooms under all combinations of three daylengths (11.5h, 12h, 12.5h) and three day/night temperatures (25/12°C, 30/15°C and 35/18°C). Growth responses were determined at 108 days and by using a growing degree day (GDD) base. A broken-stick regression model was used to determine the points of inflection, indicating the initiation of bulbing. Based on leaf area and plant height data, mathematical differentiation equations and coefficient of determination (R2) were applied to determine the base temperature (6.4°C) for these particular cultivars. All three cultivars needed at least 12 h daylength for bulb initiation when assessed by a bulbing ratio >=2.0. A bulbing ratio >=2.0 characterizes the onset of bulbing. Under a 11.5 h daylength, a temperature higher than 25/12°C decreased vegetative growth. Temperature in this region may be a supra-optimal condition for the growth of these cultivars at this daylength. However, the 25/12°C and 30/15°C temperatures were found to be ideal for onion bulb production under 12 hand 12.5 h daylengths. The three cultivars (HR I, HR 2 and RC) showed very similar growth response to the daylength and temperature interactions. The thermal presentation of plant growth indicated that there were relationships between bulb initiation and rate of leaf area growth under inductive conditions (12 hand 12.5 h). Under the 12 h daylength, cultivars needed 343, 482, and 597 GDD units before bulb initiation and 405, 432, and 431 GDD to increase the rate of leaf area development at 25/12°C, 30/15°C, and 35/18°C, respectively. Under a 12.5 h daylength, these cultivars needed 344, 423, and 432.2 GDDs to initiate bulbing and 140, 411, and 579 GDDs to increase leaf growth rates at 25/12°C, 30/15°C, and 35/18°C, respectively. In the 12 h daylength, bulbing was initiated and followed by an increased rate of growth of leaf area. However, the reverse happened for the 12.5 h daylength. Overall, where plant response to temperature can be expressed as the rate of progress towards a morphogenetic change, GDD values can be used to predict a plant developmental stage at a particular temperature. It must be concluded that temperatures induced significant variations in growth components (leaf number, plant height, leaf area), and affected bulbing response. The findings in this study confirmed that the cultivars require only a certain fixed amount of thermal time for their development at a particular temperature, and that, if anything, the slow growth rate at the higher temperature must be due to supra-optimal temperatures. They also require a minimum 12 h photoperiod for bulb formation. / Thesis (M.Sc.Agric.)-University of KwaZulu-Natal, Pietermaritzburg, 2005.

Silicon-germanium (SiGe) BiCMOS technology platforms have proven invaluable for implementing a wide variety of digital, RF, and mixed-signal applications in extreme environments such as space, where maintaining high levels of performance in the presence of low temperatures and background radiation is paramount. This work will focus on the investigation of the total-dose radiation tolerance of a third generation complementary SiGe:C BiCMOS technology platform. Tolerance will be quantified under proton and X-ray radiation sources for both the npn and pnp HBT, as well as for an operational amplifier built with these devices. Furthermore, a technique known as junction isolation radiation hardening will be proposed and tested with the goal of improving the SEE sensitivity of the npn in this platform by reducing the charge collected by the subcollector in the event of a direct ion strike. To the author's knowledge, this work presents the first design and measurement results for this form of RHBD.