No presente trabalho quatro ligas Al-Si hipereutéticas, três das quais foram produzidas por conformação por \"spray\" e a outra por fundição, foram caracterizadas quanto a textura, dureza, microestrutura e resistência à corrosão em meio de condensado sintético automotivo (CSA). Duas das ligas conformadas por \"spray\" foram retiradas de camisas de cilindro e a outra de um pré-formado obtido em laboratório. A conformação por \"spray\" envolve a atomização de uma liga e a deposição de gotículas em um substrato, antes mesmo que todas se encontrem no estado sólido. Este processo permite a obtenção de materiais que se caracterizam por uma microestrutura livre de macrossegregações e bastante refinada, implicando melhor trabalhabilidade a quente. A caracterização da microestrutura das quatro ligas hipereutéticas revelou a presença de porosidades na liga obtida em laboratório, e microestrutura com distribuição homogênea de precipitados primários nas três ligas conformadas por \"spray\". A microestrutura de uma das ligas apresentou-se muito diferenciada, com a presença de eutético, sugerindo que esta foi fabricada por fundição. Nas camisas de cilindro foram feitas medidas de rugosidade, e em todas as ligas foram realizados ensaios de microdureza. A liga conformada por \"spray\" e obtida em laboratório foi laminada a quente e a frio. Foram realizados também estudos de textura, para tentar estabelecer uma correlação entre todas as ligas quanto ao processo de fabricação. A avaliação da textura indicou que a presença de fases de silício primário, finamente distribuídas impedem o aparecimento de texturas típicas de deformação de ligas de alumínio, mesmo após severas deformações, como as necessárias para a transformação de pré-formados em tubos que originam as camisas de cilindro. As medidas de rugosidade indicaram características próprias do acabamento superficial usado para a produção das camisas, por brunimento ou por ataque químico. Os ensaios de microdureza apresentaram variações de acordo com as rotas de fabricação sendo que a liga eutética apresentou os maiores valores de microdureza em comparação às ligas conformadas por \"spray\". Todas as ligas foram avaliadas quanto a resistência à corrosão por ensaios de espectroscopia de impedância eletroquímica em dois meios, CSA com pH 3,3 e CSA com pH 11. As quatro ligas hipereutéticas estudadas apresentaram mecanismo de corrosão similar em condensado sintético automotivo (CSA) pH 3,3. Em todas ocorreu o ataque intenso da matriz de alumínio e as partículas de silício primário atuaram como regiões catódicas. A liga 2 apresentou maior resistência à corrosão entre todas as ligas ensaiadas, tanto em CSA pH 3,3 como em pH 11. Neste último meio, uma camada de produtos de corrosão formou-se sobre todas as ligas, e os resultados indicaram mecanismos diferentes para o ataque da matriz de Al e para o crescimento da camada depositada na superfície das ligas estudadas. O ataque da matriz da liga 2 neste meio foi aparentemente mais lento do que sobre as demais ligas, com a formação de uma camada mais compacta de produtos de corrosão, estabelecendo um controle por difusão dos processos interfaciais para maiores períodos de ensaio. A camada formada sobre as demais ligas neste meio apresentou-se mais defeituosa, e nestas ocorreu também menor controle da velocidade das reações interfaciais por processos difusionais. / In the present study four hypereutectic Al-Si alloys, three produced by spray forming and one by casting, were characterized for microhardness, roughness, microstructure, texture and corrosion resistance in a synthetic automotive condensed solution (SACS). Two of the spray formed alloys tested were obtained from cylinder liners and the other was laboratory made. Spray forming involves alloy atomization and droplets deposition on a substrate, previous to the solidification of all of the droplets. This process favours the production of materials with a fine microstructure free of macrosegregation that is related to improved hot workability. The microstructure characterization of the four alloys revealed the presence of porosities in the laboratory made alloy. All the three alloys produced by spray forming showed a homogeneous distribution of primary precipitates. The microstructure of one of the alloys showed eutectic microstructure, indicating that this alloy was fabricated by casting. In the cylinder liners, the surface roughness was measured and the microhardness of all the alloys was also evaluated. Furthermore, the laboratory made alloy was hot and cold rolled. Texture determinations were carried out to investigate the correlation between the alloy type and their fabrication process. The texture investigation indicated that the fine distribution of primary silicon phase in the alloy hindered the development of texture typical of aluminium alloys deformation, even after severe mechanical work, such as those used in the conversion of pre-formed in cylinder liners. The surface roughness results indicated typical characteristics of the surface finishing used, honing or chemical etching. The microhardness results were dependent on the fabrication process used, with higher microhardness associated to the eutectic alloy comparatively to the spray formed ones. All hypereutectic alloys were tested for corrosion resistance using electrochemical impedance spectroscopy in two electrolytes, SACS with pH 3.3 and SACS with pH 11. The four tested alloys showed similar corrosion mechanisms in the acid electrolyte (SACS pH 3.3). The intense attack of the aluminium matrix occurred in ali tested alloys and the primary silicon phase was unattacked and appeared as emerging from the surface after corrosion immersion test. The primary silicon particles acted as cathodic sites. The alloy 2 showed the highest corrosion resistance among the tested alloys in both electrolytes, SACS pH 3.3 and SACS pH 11. In this last medium, a layer of corrosion products formed on all the alloys, and the results indicated different mechanisms for the aluminium matrix corrosive attack and growth of the deposited layer on the alloys surface. The kinetics of aluminium matrix attack was apparently slower in the alloy 2 than for the other alloys, resulting in the formation of a more compact layer of corrosion products, leading to diffusion controlled interfacial processes for longer test periods. The layer of corrosion products on the other three alloys (1, 3, and 4) had more defects and for these alloys diffusional controlled interfacial processes were not as significant as for alloy 2.

Cette thèse présente des travaux sur l’étude et la calibration de modèles d’équations aux dérivées partielles pour la croissance tumorale. La première partie porte sur l’analyse d’un modèle de croissance tumorale pour le cas de métastases au foie de tumeurs gastro-intestinales (GIST). Le modèle est un système d’équations aux dérivées partielles couplées et prend en compte plusieurs traitements dont un traitement anti-angiogénique. Le modèle permet de reproduire des données cliniques. La première partie de ce travail concerne la preuve d’existence/unicité de la solution du modèle. La seconde partie du travail porte sur l’étude du comportement asymptotique de la solution du modèle lorsqu’un paramètre du modèle, décrivant la capacité de la tumeur à évacuer la nécrose, converge vers 0. La seconde partie de la thèse concerne le développement d’un modèle de croissance pour des sphéroïdes tumoraux ainsi que sur la calibration de ce modèle à partir de données expérimentales in vitro. L’objectif est de développer un modèle permettant de reproduire quantitativement la distribution des cellules proliférantes à l’intérieur d’un sphéroïde en fonction de la concentration en nutriments. Le travail de modélisation et de calibration du modèle a été effectué à partir de données expérimentales permettant d’obtenir la répartition spatiale de cellules proliférantes dans un sphéroïde tumoral. / In this thesis, we present several works on the study and the calibration of partial differential equations models for tumor growth. The first part is devoted to the mathematical study of a model for tumor drug resistance in the case of gastro-intestinal tumor (GIST) metastases to the liver. The model we study consists in a coupled partial differential equations system and takes several treatments into account, such as a anti-angiogenic treatment. This model is able to reproduce clinical data. In a first part, we present the proof of the existence/uniqueness of the solution to this model. Then, in a second part, we study the asymptotic behavior of the solution when a parameter of this model, describing the capacity of the tumor to evacuate the necrosis, goes to 0. In the second part of this thesis, we present the development of model for tumor spheroids growth. We also present the model calibration thanks to in vitro experimental data. The main objective of this work is to reproduce quantitatively the proliferative cell distribution in a spheroid, as a function of the concentration of nutrients. The modeling and calibration of this model have been done thanks to experimental data consisting of proliferative cells distribution in a spheroid.

Lors de l'extraction de l'uranium par lixiviation acide, AREVA fait face à des phénomènes transitoires de précipitation de phases mal cristallisées entrainant un colmatage des installations. Les analyses de ces précipités ont mis en évidence la formation d'un solide jaune minoritaire et d'un blanc majoritaire composé de sulfate de calcium et d'hydroxysulfate d'aluminium. Afin de comprendre les phénomènes menant à la précipitation et pour prévoir, éviter ou limiter leur apparition, les travaux de thèse ont consisté en l'étude expérimentale des équilibres solides-liquide du système complexe Al–Fe–K–P–S–H2O (± Ca et Mg) en milieu acide à 25°C, avec pour objectif l'identification des solides susceptibles d'apparaître en conditions industrielles. Les résultats permettront ainsi de compléter les bases de données thermodynamiques utilisées pour modéliser le comportement global du milieu lors des opérations. Après la mise au point de techniques analytiques appropriées, le travail s'est porté sur la délimitation des équilibres liquide-solides du système relatif au précipité blanc et particulièrement sur l'analyse des ternaires impliquant les hydroxysulfates d'aluminium. Le colmatage se produisant durant la phase d'acidification, l'évolution de la précipitation de ces hydroxysulfates en fonction du pH a été étudiée, afin de caractériser les solides formés en présence de cations minoritaires (Na+, K+, Mg2+, Ca2+) et de définir leurs constantes de solubilités à partir d'un modèle de calcul des coefficients d'activités des ions en solution. Des tests dynamiques sur colonne à partir de minerai naturel ont également été effectués et comparés aux résultats statiques / During the uranium extraction by acid leaching, AREVA observed the precipitation of not well crystallized solid phases, leading to the clogging of various equipment. The analyses of these precipitates highlighted the formation of a minor yellow precipitate and a major white precipitate containing calcium sulphate and aluminium hydroxisulphate. To understand the phenomena leading to the precipitation and to predict, prevent or at least limit their formation, this thesis work consisted of the solid-liquid equilibria experimental study of the Al–Fe–K–P–S–H2O (± Ca and Mg) system in an acidic environment at 25°C, with the identification of solid phases which may appear in natural ore as the major goal. The results could complete the thermodynamic database used to model global behaviour of the environment during acid mining. Based on the observed precipitates, two quaternary systems were defined, such as the H2O-Al3+, Ca2+ // O2-, SO42- system. After the development of appropriate analytical techniques, the work focused on the delimitation of the liquid-solid equilibria of the system based on the white precipitate and particularly on the analysis of the ternaries involving aluminium hydroxisulphates. As clogging occurs during acidification, the hydroxisulphate precipitation depending on the pH was studied in the presence of minority cations (Na+, K+, Mg2+, Ca2+), in order to characterise the solid phases which were formed, and to define their solubility constants. For the solubility constant determination, a calculation model of the ion activity coefficients in solution was used. A dynamic survey on a column containing natural ore was done and compared to static results

The objective of this thesis research is to improve our understanding of the flow obstacle effect on heat transfer at supercritical and high subcritical pressures by experimentally studying the effect of different obstacles on heat transfer in two vertical upward-flow test sections: a 3-rod bundle and an 8 mm ID tube. The heat transfer measurements cover the region of interest of the Canadian Super-critical Water Cooled Reactor (SCWR). A thorough analysis of the obstacle effect on supercritical heat transfer (SCHT) was performed. In the 3-rod bundle, two types of obstacles were employed: wire wraps and low-impact grid spacers. Wire wraps were found to be more effective than grid spacers to enhance the SCHT. In the tubular test section, obstacles appeared to suppress the heat transfer deterioration (HTD) or decrease its severity; obstacles also generally enhanced the SCHT both in the liquid-like and the gas- like region. The experiment in the tubular test section revealed that, at certain flow conditions (low mass flux, low inlet subcooling), flow obstacles can have an adverse impact on the SCHT. A criterion to predict the onset of this adverse effect was developed. At high subcritical pressures, obstacles increased the CHF and reduced the maximum post-CHF temperature. A comparison of the experimental data with prediction methods for the SCHT, single phase heat transfer, CHF and post-dryout heat transfer was performed. Lastly, a new correlation to predict the enhancement in SCHT due to obstacles was developed for heat transfer in the liquid-like and gas-like regions.

O fertilizante é considerado um componente essencial para a agricultura, pois sua utilização aumenta e repõe os nutrientes naturais do solo, perdidos por desgaste ou erosão. No processo de obtenção dos fertilizantes fosfatados, o concentrado de rocha reage com ácido sulfúrico concentrado produzindo ácido fosfórico e sulfato de cálcio (fosfogesso), como subproduto. O ácido fosfórico é utilizado para a produção do superfosfato triplo (TSP), superfosfato simples (SSP), monoamônio fosfato (MAP) e diamônio fosfato (DAP). A rocha fosfatada usada como matéria prima apresenta em sua composição radionuclídeos das séries naturais do urânio e tório. Durante o ataque químico do concentrado de rocha, as espécies presentes na reação, estáveis e radioativas, são redistribuídas entre o ácido fosfórico (matéria prima dos fertilizantes), e o fosfogesso, de acordo com sua solubilidade e características químicas. Enquanto os fertilizantes são comercializados, o fosfogesso fica estocado em pilhas podendo impactar o meio ambiente. Com a finalidade de entender a distribuição dos elementos e dos radionuclídeos no processo industrial de produção de fertilizantes fosfatados, foram analisadas amostras de concentrado de rocha, de fertilizantes (SSP, TSP, MAP e DAP) e fosfogesso de três procedências nacionais denominadas indústrias A, B e C. A técnica utilizada para a análise elementar foi a análise por ativação com nêutrons, que permitiu analisar os elementos Ba, Co, Cr, Fe, Hf, Na, Sc, Ta, Th, U, Zn e Zr, e as terras raras, La, Ce, Nd, Sm, Eu, Tb, Yb e Lu. Os resultados obtidos permitiram concluir que em geral, as terras raras se distribuem de forma homogênea em todos os fertilizantes e no fosfogesso, exceto o Lu. Os fertilizantes SSP e TSP apresentaram concentrações de todos os elementos analisados da mesma ordem de grandeza da rocha de origem. O mesmo comportamento foi observado nos fertilizantes MAP e DAP, exceto para os elementos Co, Sc e U. Os elementos pertencentes à série radioativa natural do urânio (238U, 234U, 230Th, 226Ra e 210Pb), do tório (232Th, 228Ra e 228Th) e o K-40, foram determinados por meio da espectrometria gama e alfa. As amostras de fertilizantes MAP e DAP, que são diretamente derivadas do ácido fosfórico, apresentaram baixa concentração para o 226Ra, 228Ra e 210Pb, enquanto que para o U e Th as concentrações encontradas foram da mesma ordem de grandeza da rocha de origem. Os fertilizantes SSP e TSP, que são obtidos pela mistura de ácido fosfórico com concentrado de rocha, apresentaram concentrações mais elevadas para os radionuclídeos das séries naturais. Avaliou-se a exposição devido a sucessivas aplicações de fertilizantes e fosfogesso, calculando-se a dose interna devida à aplicação por 10, 50 e 100 anos. Os valores encontrados estão abaixo do limite de 2,4 mSv a-1, mostrando que esta prática é negligenciável. / Fertilizer is considered an essential component for agriculture, because its use increases the natural soil nutrients, which are lost slow waste or erosion. The Brazilian phosphate fertilizer is obtained by wet reaction of igneous phosphate rock with concentrated sulphuric acid, giving as final product, phosphoric acid and dihydrated calcium sulphate (phosphogypsum) as by-product. Phosphoric acid is the starting material for triple superphosphate (TSP), single superphosphate (SSP), monoammonium phosphate (MAP) and diammonium phosphate (DAP). The phosphate rock used as raw material presents in its composition, radionuclides of the U and Th natural series in. During the chemical attack of the phosphate rock, this equilibrium is disrupted and the radionuclides and the elements migrate to intermediate, final products and by-products, according to their solubility and chemical properties. While the fertilizers are commercialized, the phosphogypsum is disposed in stack piles and can cause an impact in the environment. In order to evaluate the radionuclides and the elements distribution in the industrial process of phosphate fertilizer production, samples of concentrated rock, fertilizers (SSP, TSP, MAP and DAP) and phosphogypsum from three national industries (A, B and C), were analyzed. The characterization of the elements Ba, Co, Cr, Fe, Hf, Na, Sc, Ta, Th, U, Zn and Zr, and the rare earths La, Ce, Nd, Sm, Eu, Tb, Yb and Lu, were performed by instrumental neutron activation analysis. The results obtained showed that, in general, the rare earth elements are distributed uniformly in the fertilizers and phosphogypsum, except for Lu. The elemental concentration present in the fertilizers SSP and TSP are of the same order of magnitude of the source rock. The same behavior was observed in the fertilizers MAP and DAP, except for the elements Co, Sc and U. The radionuclides of the U series (238U, 234U, 230Th, 226Ra, 210Pb) and of the Th series (232Th, 228Ra, 228Th) and 40K were determined by gamma and alpha spectrometry. The fertilizers samples, with are derived directly from phosphoric acid, MAP and DAP, presented in their composition low activity concentrations for 226Ra, 228Ra and 210Pb. For U and Th, the concentrations founded in MAP and DAP are more significant, similar to the source rock. SSP and TSP fertilizers, which are obtained by mixing phosphoric acid with different amounts of phosphate rock, presented higher concentrations of all radionuclides of the natural series. Long-term exposure due to successive fertilizer and phosphogypsum application was evaluated. Internal doses due to the application of phosphate fertilizer and phosphogypsum for 10, 50 and 100 years were below 2.4 mSv y-1, showing that the radiological impact of such practice is negligible.

"Review of the literature shows that the reported correlation between predictions and experimental data of flame spread vary greatly. The discrepancies displayed by the models are generally attributed to inaccurate input parameters, user effects, and inadequacy of the model. In most experiments, the metric to which the model is deemed accurate is based on the prediction of the heat release rate, but flame spread is a highly complex phenomenon that should not be simplified as such. Moreover, fire growth models are usually made up of distinctive groups of calculation on separate physical phenomena to predict processes that drive fire growth. Inaccuracies of any of these “sub-models” will impact the overall flame spread prediction, hence identifying the sources of error and sensitivity of the subroutines may aid in the development of more accurate models. Combating this issue required that the phenomenon of flame spread be decomposed into four components to be studied separately: turbulent fluid dynamics, flame temperature, flame heat transfer, and condensed phase pyrolysis. Under this framework, aspects of a CFD model may be validated individually and cohesively. However, a lack of comprehensive datasets in the literature hampered this process. Hence, three progressively more complex sets of experiments, from free plume fires to fires against an inert wall to combustible wall fires, were conducted in order to obtain a variety of measurements related to the four inter-related components of flame spread. Multiple permutations of the tests using different source fuels, burner size, and source fire heat release rate allowed a large amount of comparable data to be collected for validation of different fire configurations. FDS simulations using mostly default parameters were executed and compared against the experimental data, but found to be inaccurate. Parametric study of the FDS software shows that there are little definitive trends in the correlation between changes in the predicted quantities and the modeling parameters. This highlights the intricate relationships shared between the subroutines utilized by FDS for calculations related to the four components of flame spread. This reveals a need to examine the underlying calculation methods and source code utilized in FDS."

O fertilizante é considerado um componente essencial para a agricultura, pois sua utilização aumenta e repõe os nutrientes naturais do solo, perdidos por desgaste ou erosão. No processo de obtenção dos fertilizantes fosfatados, o concentrado de rocha reage com ácido sulfúrico concentrado produzindo ácido fosfórico e sulfato de cálcio (fosfogesso), como subproduto. O ácido fosfórico é utilizado para a produção do superfosfato triplo (TSP), superfosfato simples (SSP), monoamônio fosfato (MAP) e diamônio fosfato (DAP). A rocha fosfatada usada como matéria prima apresenta em sua composição radionuclídeos das séries naturais do urânio e tório. Durante o ataque químico do concentrado de rocha, as espécies presentes na reação, estáveis e radioativas, são redistribuídas entre o ácido fosfórico (matéria prima dos fertilizantes), e o fosfogesso, de acordo com sua solubilidade e características químicas. Enquanto os fertilizantes são comercializados, o fosfogesso fica estocado em pilhas podendo impactar o meio ambiente. Com a finalidade de entender a distribuição dos elementos e dos radionuclídeos no processo industrial de produção de fertilizantes fosfatados, foram analisadas amostras de concentrado de rocha, de fertilizantes (SSP, TSP, MAP e DAP) e fosfogesso de três procedências nacionais denominadas indústrias A, B e C. A técnica utilizada para a análise elementar foi a análise por ativação com nêutrons, que permitiu analisar os elementos Ba, Co, Cr, Fe, Hf, Na, Sc, Ta, Th, U, Zn e Zr, e as terras raras, La, Ce, Nd, Sm, Eu, Tb, Yb e Lu. Os resultados obtidos permitiram concluir que em geral, as terras raras se distribuem de forma homogênea em todos os fertilizantes e no fosfogesso, exceto o Lu. Os fertilizantes SSP e TSP apresentaram concentrações de todos os elementos analisados da mesma ordem de grandeza da rocha de origem. O mesmo comportamento foi observado nos fertilizantes MAP e DAP, exceto para os elementos Co, Sc e U. Os elementos pertencentes à série radioativa natural do urânio (238U, 234U, 230Th, 226Ra e 210Pb), do tório (232Th, 228Ra e 228Th) e o K-40, foram determinados por meio da espectrometria gama e alfa. As amostras de fertilizantes MAP e DAP, que são diretamente derivadas do ácido fosfórico, apresentaram baixa concentração para o 226Ra, 228Ra e 210Pb, enquanto que para o U e Th as concentrações encontradas foram da mesma ordem de grandeza da rocha de origem. Os fertilizantes SSP e TSP, que são obtidos pela mistura de ácido fosfórico com concentrado de rocha, apresentaram concentrações mais elevadas para os radionuclídeos das séries naturais. Avaliou-se a exposição devido a sucessivas aplicações de fertilizantes e fosfogesso, calculando-se a dose interna devida à aplicação por 10, 50 e 100 anos. Os valores encontrados estão abaixo do limite de 2,4 mSv a-1, mostrando que esta prática é negligenciável. / Fertilizer is considered an essential component for agriculture, because its use increases the natural soil nutrients, which are lost slow waste or erosion. The Brazilian phosphate fertilizer is obtained by wet reaction of igneous phosphate rock with concentrated sulphuric acid, giving as final product, phosphoric acid and dihydrated calcium sulphate (phosphogypsum) as by-product. Phosphoric acid is the starting material for triple superphosphate (TSP), single superphosphate (SSP), monoammonium phosphate (MAP) and diammonium phosphate (DAP). The phosphate rock used as raw material presents in its composition, radionuclides of the U and Th natural series in. During the chemical attack of the phosphate rock, this equilibrium is disrupted and the radionuclides and the elements migrate to intermediate, final products and by-products, according to their solubility and chemical properties. While the fertilizers are commercialized, the phosphogypsum is disposed in stack piles and can cause an impact in the environment. In order to evaluate the radionuclides and the elements distribution in the industrial process of phosphate fertilizer production, samples of concentrated rock, fertilizers (SSP, TSP, MAP and DAP) and phosphogypsum from three national industries (A, B and C), were analyzed. The characterization of the elements Ba, Co, Cr, Fe, Hf, Na, Sc, Ta, Th, U, Zn and Zr, and the rare earths La, Ce, Nd, Sm, Eu, Tb, Yb and Lu, were performed by instrumental neutron activation analysis. The results obtained showed that, in general, the rare earth elements are distributed uniformly in the fertilizers and phosphogypsum, except for Lu. The elemental concentration present in the fertilizers SSP and TSP are of the same order of magnitude of the source rock. The same behavior was observed in the fertilizers MAP and DAP, except for the elements Co, Sc and U. The radionuclides of the U series (238U, 234U, 230Th, 226Ra, 210Pb) and of the Th series (232Th, 228Ra, 228Th) and 40K were determined by gamma and alpha spectrometry. The fertilizers samples, with are derived directly from phosphoric acid, MAP and DAP, presented in their composition low activity concentrations for 226Ra, 228Ra and 210Pb. For U and Th, the concentrations founded in MAP and DAP are more significant, similar to the source rock. SSP and TSP fertilizers, which are obtained by mixing phosphoric acid with different amounts of phosphate rock, presented higher concentrations of all radionuclides of the natural series. Long-term exposure due to successive fertilizer and phosphogypsum application was evaluated. Internal doses due to the application of phosphate fertilizer and phosphogypsum for 10, 50 and 100 years were below 2.4 mSv y-1, showing that the radiological impact of such practice is negligible.

La finalidad de esta tesis es la obtención de las distribuciones de velocidades, presiones y temperaturas en la convección forzada de flujos compresibles en situaciones bidimensionales y de estabilización. Es a partir de estos valores que se determina la fricción y la transferencia de calor entre el fluido y el contorno o canalización.La tesis consta de cinco capítulos. En el primero, de carácter introductorio, se plantea la problemática de resolución de las ecuaciones que describen el comportamiento del flujo. Se analizan dos niveles de modelización. De una parte, y en base al concepto de capa límite introducido por L. Prandtl, se divide el dominio por el que circula el flujo en dos zonas: unas delgadas regiones próximas a los contornos sólidos en los que la fricción y la transferencia de calor son factores condicionantes, y el resto del dominio en el que el flujo puede considerarse como no viscoso, pudiéndose despreciar los efectos de la fricción y de la transferencia de calor. En el segundo nivel de modelización se plantea la resolución directa de las ecuaciones de continuidad, cantidad de movimiento y energía en todo el dominio.Los capítulos segundo, tercero y cuarto están dedicados al primer nivel de modelización indicado. En el segundo capítulo se resuelve el flujo potencial compresible en base a la discretización del dominio mediante la generación de mallas adaptables a los contornos. Se analizan diferentes criterios de discretización de las ecuaciones siendo los resultados numéricos obtenidos contrastados entre si y con los que se derivan del empleo de mallas de discretización rectangulares. El tercer capítulo trata de la resolución de las capas límites hidrodinámicas y térmicas mediante la integración numérica de la ecuaciones de conservación. Para el análisis de las capas límite turbulentas se ha utilizado los conceptos de viscosidad turbulenta y conductividad térmica turbulenta, empleándose expresiones semiempíricas en la descripción de dichas cantidades. Se estudian diversas situaciones contrastándose los resultados numéricos obtenidos con los que se derivan de estudios experimentales presentados por distintos autores. En el cuarto capítulo se efectúa la resolución conjunta de la zona potencial y de las capas límite en el marco de un algoritmo global de resolución. A modo ilustrativo se ha realizado el estudio del flujo de aire en una tobera o canalización convergente, analizándose aspectos tales como la compresibilidad del flujo y la transferencia de calor entre el fluido y los contornos sólidos limitantes. Los resultados que se derivan de la resolución numérica, supuestos los contornos adiabáticos, son contratados con los obtenidos experimentalmente en esta tesis y en una unidad de soplado del laboratorio. En el quinto y último capítulo se aborda el segundo nivel de modelización arriba indicado, si bien la atención se centra en ecuaciones genéricas del tipo convección-difusión. Así, partiendo de una distribución de velocidades conocida, se realiza la resolución de dicha ecuación en base a la generación de sistemas ortogonales de coordenadas curvilíneas coincidentes con las propias líneas de corriente del flujo. La precisión y zonas de aplicación del método numérico son puestas de manifiesto en situaciones singulares de solución analítica conocida. Los resultados obtenidos son satisfactorios en un amplio rango de números de Peclet, y claramente superiores a los que se derivan del empleo de mallas de discretización rectangulares. / The purpose of this thesis is to obtain velocity, pressure and temperature distributions in compressible flows under steady-state conditions.The thesis has five chapters. The first one introduces the mathematical formulation and two main strategies to solve the governing equations. The first one is based on a zonal model, which solved in a coupled manner the Euler and the boundary layer equations. The second level is based on the resolution of the Navier-Stokes equations in the whole domain.The next three chapters are devoted to the first level of modelization mentioned above. The second chapter solves the Euler equations of the inviscid flow based on the discretization of the domain by means of body-fitted meshes. Numerical solutions are also carefully verificated based on grid refinement techniques. Several numerical criteria for the discretization of the equations are presented and contrasted. The third chapter deals with the numerical integration of the hydrodynamic and thermal boundary layer equations using algebraic turbulence models extended to compressible flows. A study of the different parameters which influence on flow is presented.In the fourth chapter, a coupled procedure of the two zones (inviscid zone and boundary layers) is proposed within the framework of a global algorithm. By way of illustration the study of the compressible flow in a converging channel is carried out. Different aspects related to the compressibility of the flow and the heat transfers exchanged with the solid boundaries are studied. The mathematical model is validated against experimental results obtained in a specially designed set-up.In the fifth and final chapter, the second level of modelization is presented but only the part which refers to generic convection-diffusion equations. Thus, starting from a known velocity distribution, an analysis of different standard numerical schemes is performed together with a proposal of a new scheme to reduce the numerical false diffusion effects.

Les métamatériaux sont définis comme étant des matériaux artificiels présentant des propriétés exotiques qui modifient la propagation des ondes électromagnétiques. À la fin des années 90, Pendry et al. démontrèrent théoriquement qu'il est possible de générer de tels métamatériaux, grâce à des structures particulières au sein du matériau (le fameux "splitring resonator"). Les métamatériaux sont donc structurés à une échelle inférieure à la longueur d'onde incidente, et décrits par une permittivité et une perméabilité effective. En 2000, Smith et al. fabriquèrent le premier métamatériau mais dans la gamme micro-onde. Les perspectives dans le domaine de l'optique (300800 nm) sont très prometteuses, mais le transfert des technologies utilisées en micro-ondes rencontre des obstacles. Un des défis dans le domaine émergent des métamatériaux est d'assembler à grande échelle des nanoparticules NPs (10-50 nm) en des super-réseaux présentant des propriétés collectives. Des nanostructures tridimensionnelles de matériaux nobles, ayant de fortes réponses plasmoniques, peuvent en effet générer des matériaux aux nouvelles propriétés optiques. Cette thèse fait partie du projet européen METACHEM, dont le but est de fabriquer des métamatériaux dans le domaine de l'infrarouge et du visible, en se basant sur l'utilisation de la nanochimie et de l'assemblage de matériaux. Plus précisément, ce travail de thèse se situe à l'interface entre les groupes de chimie qui synthétisent des nanoparticules en dispersion, et les groupes de caractérisation optique des matériaux. Dans ce travail de thèse, nous utilisons une technique originale la microévaporation basée sur les outils microfluidiques, afin de générer de façon contrôlée des assemblées 3D de nanoparticules (dimensions typiques 1 mm10 m 50 m). / 1-Microevaporation - Microfluidics is the branch of fluid mechanics dedicated to the study of flows in the channel withdimensions between 1 micron and 100 micron. The object of this chapter is to illustrate the basicprinciples and possible applications of microfluidic chip, called microevaporator. In the first part ofthe chapter, we present a detailed description of the physics of microevaporators using analyticalarguments, and describe some applications. In the second part of the chapter, we present theexperimental protocol of engineering of micro evaporator and different type of microfluidics device.2- On-chip microspectroscopy - The object of this chapter is to illustrate a method to measure absorption spectra during theprocess of growth of our materials in our microfluidic tools. The aim is to make an opticalcharacterization of our micro materials and to carry-out a spatio-temporal study of kineticproperties of our dispersion under study. This instrumental chapter presents the theoretical basis !of the method we used.3-Role of colloidal stability in the growth of micromaterials - We used combined microspectroscopy and videomicroscopy to follow the nucleation and growth ofmaterials made of core-shell Ag@SiO2 NPs in micro evaporators.!We evidence that the growth is actually not always possible, and instead precipitation may occurduring the concentration process. This event is governed by the concentration of dispersion in thereservoir and we assume that its origin come from ionic species that are concentrated all togetherwith the NPs and may alter the colloidal stability en route towards high concentration. 4-Microfluidic-induced growth and shape-up of three-dimensional extended arrays of denselypacked nano particles - In this chapter I present in details microfluidic evaporation experiments to engineer various denselypacked 3D arrays of NPs.5-Bulk metamaterials assembled by microfluidic evaporation - In this chapter I introduced the technique we used (microspot ellipsometry) in close collaborationswith V.Kravets and A.Grigorenko(University of Manchester) and with A.Aradian, P.Barois, A.Baron,K.Ehrhardt(CRPP, Pessac) to characterized the solids made of densely packed NPs. I describe theconstraints that emerge from the coupling between the small size of our materials and the opticalrequirements, the analysis and interpretation of the ellipsometry experiments show that for thematerial with high volume fraction of metal exists the strong electrical coupling between the NPsand the materials display an extremely high refraction index in the near infra-red regime.

Celui-ci a pour objectif de valider l'ensemble des modèles physiques utilisés dans un code de simulation numérique pour simuler un écoulement de type annulaire dispersé en conduite rencontré lors d'une procédure de lavage à eau utilisé dans les raffineries. Pour ce faire une banque de données expérimentale est mise en place sur des configurations représentatives de celles utilisées en condition industrielle. La géométrie retenue comporte une zone horizontale d'injection rectiligne avec un injecteur central, suivi d'un coude à 90° situé dans un plan vertical. Différentes conditions expérimentales permettent d'étudier l'influence de la vitesse du gaz, de la condition d'injection du brouillard et de la pression sur les différents processus physiques. Ces résultats comprenant des visualisations du brouillard et du film pariétale, des mesures de taille et de distribution de gouttes,des mesures de débit et d'épaisseur de film, sont analysés pour faire ressortir les principaux mécanismes d'interaction entre le gaz et la phase dispersée, le gaz et le film liquide pariétal et la phase dispersée et le film pariétal. En parallèle, des premières simulations, avec une approche RANS, sont réalisées avec le code CEDRE de l'ONERA et les résultats sont confrontés aux mesures. / This work has been realised within a CIFRE contract with TOTAL. Its aim was to validate all the physical models used in a computation, which simulates an annular dispersed flow through a pipe used in a water washing process in refinery plants. That is why, a whole set of data has been gathered using experimental boundary conditions which are representative to those used in industrial configurations. The geometry is made of a horizontal pipe with a centred nozzle followed by a 90º elbow in the vertical plane. Several experimental boundary conditions enable one to study the influence of the gas velocity, the type of the spray injection and the pressure on the different physical phenomena. These results including spray and liquid film visualisations, droplets distribution and size measurements as well as liquid film thickness and mass flow measurements were analysed in order to extract the main interaction mechanism between the gas and the dispersed phase, the gas and the liquid film, and the dispersed phase and the annular liquid film. Meanwhile, simulations using a RANS approach were realized with the ONERA code named CEDRE and its results were compared to the gathered measurements.