[pt] Deformabilidade e estabilidade de taludes em solo grampeado são aspectos relevantes na utilização deste sistema de reforço de taludes naturais ou resultantes de processo de escavação. A concepção do projeto envolve a escolha do comprimento, ângulo de instalação, espaçamento e resistência dos grampos. O dimensionamento, usualmente baseado na teoria do Equilíbrio Limite, não consegue prever deformações no interior da massa grampeada, assim como a redistribuição de esforços nos grampos ao longo das diversas etapas de escavação. Estas informações podem ser obtidas por modelagem computacional com o auxílio do programa FLAC, de forma a definir critérios de projeto para massas grampeadas em solo residual. Para escavações de baixa altura (inferiores a 5m), a razão entre comprimento do grampo e altura da escavação deve ser superior a 0,7 e a razão entre espaçamento vertical e comprimento do grampo inferior a 50%. Para escavações maiores, a razão entre espaçamento vertical e comprimento do grampo deve ser inferior a 25%. Para estas condições não é observada uma configuração de colapso do talude em solo grampeado. O ângulo de rotação da face da escavação é um parâmetro importante no projeto. Adicionalmente verifica-se que uma pequena variação na geometria, condições de contorno, modelo constitutivo e parâmetros do solo e do grampo causam mudanças expressivas nos valores de deslocamento, tensões iniciais e esforços axiais nos grampos. Uma pequena variação da inclinação do talude pode acarretar reduções de até 70% nos deslocamentos finais. Os esforços axiais máximos, mobilizados em cada grampo durante o processo de escavação, são maiores nos taludes mais íngremes. / [en] Deformability and stability of slopes supported by soil nailing are relevant aspects in the utilization of this reinforcement system during excavation. The project concept involves choosing the installation angle, spacing, and resistance of the soil nails. The parameters, usually determined from Limit Equilibrium Theory, cannot predict the deformation of the reinforced mass or the redistribution of stresses on the nails throughout the excavation stages. This information was obtained through computer modeling using the FLAC Program, which defined the performance of soil nailing masses in residual soil. For shallow excavations (H < 5m), the ratio between length and excavation height must be a minimum of 0.7, the ratio between spacing and length up to a maximum of 0.5. For higher excavations, the ratio between spacing and length has to be reduced to 0.25. The rotation angle of the excavation s face is an important parameter. Additionally, small variations in the geometry, boundary conditions, constitutive model, and soil and nail parameters, can cause large changes in the deformations, initial tensions and axial stresses in the nails. Regarding the slope inclination, a small variation can cause reductions of up to 70% in the final deformations. The maximum axial stresses mobilized in each nail during the process of excavation are larger in steeper slopes.

<p>The market of portable digital audio players (DAPs) have literally exploded the last couple of years. Other markets has grown as well. PDAs, GPS receivers, mobile phones, and so on. This resulted in more advanced ICs and SoCs becoming publically available, eliminating the need for in-house ASICs, thus enableing smaller actors to enter the markets.</p><p>This thesis explores the possibilities of developing a low power, hand-held device on a very limited budget and strict time scale.</p><p>This thesis report also covers all the steps taken in the development procedure.</p>

Vertical inclusions of expanded polystyrene (EPS) placed behind rigid retaining walls were investigated as geofoam seismic buffers to reduce earthquake-induced loads. A numerical model was developed using the program FLAC and the model validated against 1-g shaking table test results of EPS geofoam seismic buffer models. Two constitutive models for the component materials were examined: elastic-perfectly plastic with Mohr-Coulomb (M-C) failure criterion and non-linear hysteresis damping model with equivalent linear method (ELM) approach. It was judged that the M-C model was sufficiently accurate for practical purposes. The mechanical property of interest to attenuate dynamic loads using a seismic buffer was the buffer stiffness defined as K = E/t (E = buffer elastic modulus, t = buffer thickness). For the range of parameters investigated in this study, K ≤ 50 MN/m3 was observed to be the practical range for the optimal design of these systems. Parametric numerical analyses were performed to generate design charts that can be used for the preliminary design of these systems. A new high capacity shaking table facility was constructed at RMC that can be used to study the seismic performance of earth structures. Reduced-scale models of geosynthetic reinforced soil (GRS) walls were built on this shaking table and then subjected to simulated earthquake loading conditions. In some shaking table tests, combined use of EPS geofoam and horizontal geosynthetic reinforcement layers was investigated. Numerical models were developed using program FLAC together with ELM and M-C constitutive models. Physical and numerical results were compared against predicted values using analysis methods found in the journal literature and in current North American design guidelines. The comparison shows that current Mononobe-Okabe (M-O) based analysis methods could not consistently satisfactorily predict measured reinforcement connection load distributions at all elevations under both static and dynamic loading conditions. The results from GRS model wall tests with combined EPS geofoam and geosynthetic reinforcement layers show that the inclusion of a EPS geofoam layer behind the GRS wall face can reduce earth loads acting on the wall facing to values well below those recorded for conventional GRS wall model configurations. / Thesis (Ph.D, Civil Engineering) -- Queen's University, 2011-04-28 16:56:57.084

The following report is the results of a master thesis project performed on the behalf of Boliden Tara Mines. The work includes a numerical modelling study with the main purpose to evaluate the room- and pillar stability for the mining method "drift-and-slash" mining currently used in the Tara Mine when mining in thin, low-rise lenses. Also, the potential of applying the "drift-and-fill" mining method was studied during the project. The numerical modelling work was performed both two-dimensionally and three-dimensionally, using the Itasca software FLAC and FLAC3D.  The study resulted in recommendations regarding the room- and pillar dimensions, mining sequence, rock support, mining method and further studies. It was concluded that the currently used room- and pillar dimensions could be altered to increase the extraction ratio and that the mining sequence and rock support should be determined depending on the room- and pillar dimensions. Also, that it could be possible to change from the drift-and-slash method to the drift-and-fill method from a stability perspective. Lastly, it was recommended to further study the rock strength and to monitor the pillar behaviour.

In this investigation, seismic response of retaining walls constructed with cohesive and cohesionless backfill materials was studied. Fully dynamic analysis based on finite difference method was used to evaluate the performance of retaining walls during the earthquake. The analysis response was verified by the experimental study conducted on a retaining wall system with cohesive backfill material in the literature. The effects of cohesion and free-field peak ground acceleration (PGA) on seismic earth thrust, the point of action of earth thrust, and maximum wall moment during the earthquake were compared with analytical and experimental solutions. The numerical results were compared with various analytical solutions. The motion characteristics of the retaining wall during the earthquake were also considered. The relative displacement of the walls with various backfill cohesions, under different ground motions, and free-field PGAs were investigated. Current analytical and empirical correlations developed based on Newmark sliding block method for estimating retaining wall movement during earthquakes were compared with the numerical approach. Consequently, fragility analyses were conducted to determine the probability of damage to the retaining walls. To evaluate the fragility of the studied models, specific failure criterion was chosen for retaining walls based on the suggested methods in practice. Using numerical approaches, the effects of soil-wall interaction and wall rigidity on the seismic response of retaining walls were also evaluated in earthquake conditions for both cohesive and cohesionless backfill materials. According to the findings, practical correlations were presented for conducting the seismic design of retaining walls.

No description available.

No description available.

Two-dimensional analysis of four types of water-filled tube dams is carried out: an apron-tube dam, a single baffle tube dam, a sleeved tube dam, and a stacked tube dam. Since the analysis of the water-filled tube dam involves highly nonlinear geometric deformations and interactions with soil, fluid, and structure, it is solved numerically with the explicit finite difference program FLAC. The tube is numerically modeled with beam elements. The predicted contact regions are modeled with interface elements. The Mohr-Coulomb constitutive model is used for the soil. Water inside and outside of the tube is modeled as hydrostatic pressure and the pressures are continuously updated as the configuration of the tube is changed. The change of the internal water pressure head (IWPH) for maintaining a constant tube area during the deformation is simulated. The simulation is achieved by two iterative procedures, the secant method and the factored secant method. The numerical analysis results show good agreement with the experimental results overall: the deformation of the tube(s), the IWPH changes, and the critical external water heights. From the numerical simulation of the experiments and the parametric studies, the behavior of each type of water-filled tube dam is clarified. Also, the failure modes of the tube dams are examined. The failure mode of a tube dam depends on the configuration and IWPH of the tube dam and the characteristics of the soil surface. / Ph. D.

Pile-supported T-walls, which are concrete floodwalls that are shaped like an inverted "T" and supported by batter piles, are commonly used by the United States Army Corps of Engineers (USACE) to protect low-lying portions of New Orleans and other areas. The design of a T-wall in southern Louisiana is complex, as the structure needs to resist both 1) large settlements caused by fill placed beneath and beside the T-wall before T-wall construction or by fill placed beside the T-wall after T-wall construction, and 2) large lateral flood loads that are imposed during a hurricane. As a result of these loading conditions, large bending moments can develop in the batter piles and these moments need to be accounted for as part of the T wall design. The goal of this research is to develop a more complete understanding of the pile bending moments in T wall systems, specifically for cross sections where large settlements may occur. As a first step towards this goal, Rensselaer Polytechnic Institute (RPI) performed a series of eight centrifuge tests to investigate and physically model the effects of settlement-induced bending moments on pile-supported T-walls. The centrifuge tests were evaluated and interpreted, and in order to better capture uncertainty, upper and lower bounds were estimated for the interpreted data. The centrifuge results offered some valuable insights on their own, but were ultimately used as the basis for validating and calibrating corresponding numerical models. The numerical models were developed following a rigorous modeling approach and using rational and reasonable assumptions based on widely-accepted and well-justified procedures. The numerical model results were in good agreement with the centrifuge results without the need for significant calibration or modifications. This good agreement indicates that similar numerical models can be developed to reliably analyze actual T-wall cross sections. Detailed recommendations were developed for using numerical models to analyze pile-supported T walls, and an example problem is presented herein that illustrates the application of this approach. These same techniques were then used to perform a parametric study to analyze the combined and separate effects of flood loading for a wide range of different T-wall cross sections. The range was selected in collaboration with the USACE in order to reasonably cover cross sections and conditions that 1) are typically encountered in practice, and 2) were expected to generate both upper and lower bound pile bending moments. In total, 3,648 cross sections were analyzed, and 29,184 sets of analysis results were generated since each cross section was analyzed for eight different loading conditions. Summary results are provided to show the influence of the loading conditions and parameters on T-wall response, including the influence of flood loading, new fill symmetry, pile fixity, number of piles, subsurface profile, pile batter, pile type, levee slope, T-wall elevation, and the presence of existing levee fill. In addition, the key results for all of the analyses are provided in the appendices and in an electronic database. Based on the parametric study results, a simplified analysis procedure was developed that can be used to calculated maximum pile bending moments for T walls installed directly on foundation soils due to settlements. In this procedure, the loads from new fill placed during or after T-wall construction are distributed onto the pile, and the pile response is analyzed using traditional p-y curves and a beam on elastic foundation formulation. This procedure shows good agreement with the numerical model results for a range of conditions. To demonstrate the application of the procedure, the same example problem that is analyzed numerically is reanalyzed using the simplified analysis procedure. Due to the complexity of the problem, it was not possible to modify this procedure or develop a similar procedure for T-walls installed on top of new or existing levees. Overall, this research demonstrates that numerical models can be used to calculate the bending moments that can develop in pile-supported T-walls due to settlements and flood loading, provides valuable insights into the behavior of T-walls and the influence of various parameters on T-wall response, presents a large database of T-wall analysis results, and recommends a simplified analysis procedure that can be used in some cases to calculate pile bending moments due to settlements. / Ph. D.

[pt] O fenômeno de liquefação continua sendo um dos temas mais importantes, complexos e controversos da engenharia geotécnica, sendo a liquefação dinâmica, causada por terremotos, o maior contribuinte de risco sísmico urbano em vários países andinos. O movimento causa incrementos da poropressão que reduz a tensão efetiva e conseqüentemente a resistência ao cisalhamento de solos arenosos. O presente trabalho de pesquisa apresenta e compara algumas das metodologias existentes para a avaliação do fenômeno de liquefação dinâmica, variando desde o método semi-empírico de Seed-Idriss para estimativas do potencial de liquefação até a execução de algumas análises numéricas, no contexto dinâmico, através do programa computacional FLAC 2D v.5. Um estudo de caso, para uma comparação dos diversos procedimentos, consiste na análise dinâmica de uma pilha de lixiviação de minério de cobre, situada em região de atividade sísmica no Peru que, devido a problemas no sistema de drenagem interna, resultou com um alto nível de saturação que poderia colocar sua estabilidade em risco devido à possibilidade de liquefação sob carregamento sísmico. Dos resultados obtidos nessas análises, pode-se afirmar que o método semi-empírico de Seed-Idriss, para determinação do potencial de liquefação, compara-se bastante bem com modelos mais sofisticados baseados em análises dinâmicas empregando tanto o modelo constitutivo de Finn quanto o modelo constitutivo elastoplástico UBCSAND. / [en] The phenomenon of liquefaction is still one of the most important, complex and controversial subjects of the geotechnical engineering, being the dynamic liquefaction, caused by earthquakes, the major contributor to urban seismic risks in several Andesian countries. The shaking increases the pore water pressure which reduces the soil effective stress and, therefore, the shear strength of sandy soils. This dissertation presents and compares some of the proposed methodologies to evaluate the phenomenon of dynamic liquefaction, ranging from the semi-empirical method of Seed-Idriss to estimate the liquefaction potential to the execution of some numerical analyses, within the dynamic context, through the computational program FLAC 2D v.5. The case study, for the comparison among the several procedures, consists of a copper ore heap leach, situated in a high seismic activity zone in Peru, that experimented high levels of saturation, due to problems in the internal drainage system, that could put in risk the stability of the leach pad to the possibility of liquefaction under seismic loading. From the results of such analyses, one can say that the semi-empirical method proposed by Seed- Idriss for the determination of the liquefaction potential compares quite well with outputs from more sophisticated numerical analyses based on dynamic studies that incorporate either the Finn s or the elasto-plastic UBCSAND constitutive models.